CURRENT 6.0 Amperes VOLTAGE 50 to 600 Volts SF61 THRU SF67 Features · Low forward voltage drop · High current capability · High reliability · High surge current capability · Super fast recovery time · Good for use in switching mode circuits · Plastic package has Underwrites Laboratory Flammability Classification 94V-0 P-6 0.360(9.1) 0.340(8.6) DIA. 1.0(25.4) MIN. 0.360(9.1) 0.340(8.6) Mechanical Data · Case : P-6 molded plastic body · Terminals : Plated axial lead solderable per MIL-STD-750, method 2026 · Polarity : Color band denotes cathode end · Mounting Position : Any · Weight : 0.07 ounce, 2.1 gram 1.0(25.4) MIN. 0.052(1.3) 0.048(1.2) DIA. Dimensions in inches and (millimeters) Maximum Ratings And Electrical Characteristics (Ratings at 25℃ ambient temperature unless otherwise specified, Single phase, half wave 60Hz, resistive or inductive load. For capacitive load, derate by 20%) Symbols SF61 SF62 SF63 SF64 SF65 SF66 SF67 Units Maximum recurrent peak reverse voltage VRRM 50 100 150 200 300 400 600 Volts Maximum RMS voltage VRMS 35 70 105 140 210 280 420 Volts Maximum DC blocking voltage VDC 50 100 150 200 300 400 600 Volts Maximum average forward rectified current 0.375"(9.5mm) lead length at TA=55℃ I(AV) 6.0 Amps Peak forward surge current 8.3ms single half sine-wave superimposed on rated load (JEDEC method) IFSM 150 Amps Maximum instantaneous forward voltage at 6.0A VF Maximum DC reverse current at rated DC blocking voltage IR TA=25℃ 1.70 10 TA=100℃ Volts μA 100 Maximum reverse recovery time (Note 1) Trr Typical junction capacitance (Note 2) CJ Operating junction and storage temperature range 1.30 0.95 TJ TSTG Notes: (1) Test conditions: IF=0.5A, IR=1.0A, Irr=0.25A. (2) Measured at 1MHz and applied reverse voltage of 4.0 Volts. ns 35 60 120 -55 to +125 -55 to +150 pF ℃ RATINGS AND CHARACTERISTIC CURVES SF61 THRU SF67 10 50 NONINDUCTIVE NONINDUCTIVE (+ ) 50Vdc (approx) (-) AND TEST CIRCUIT DIAGRAM +0.5A DUT PULSE GENERATOR (NOTE 2 ) FIG . 2 -MAXIMUM AVERAGE FORWARD CURRENT DERATING trr AVERAGE FORWARD CURRENT . ( A ) FIG . 1 -REVERSE RECOVERY TIME CHARACTERISTIC 0 -0.25A OSCILLOSCOPE (NOTE 2 ) NOTES: 1 . RISE TIME = 7nsmax. INPUT IMPEDANCE= 1 MEGOHM 22p 2 . RISETIME = 10ns max. SOURSE IMPEDANCE = 50ohmsf -1.0A 1cm FIG . 3 -TYPICAL REVERSE CHARACTERISTICS SET TIME BASE FOR 5/ 10ns / cm 6.0 5.0 4.0 3.0 SINGLE PHASE HALF WAVE 60Hz RESISTIVE OR INDUCTIVE LOAD 0.375"(9.5m m) LEAD LENGTH 2.0 1.0 25 50 75 100 125 150 175 AMBIENT TEMPERATURE . (OC) FIG . 4 -TYPICAL REVERSE CHARACTERISTICS 100.0 10 TJ=25O C 1 .1 0 20 40 60 80 100 F6 4 -S 10.0 6 F6 SF 1.0 67 0.1 .01 .4 120 -S 65 SF TJ=100OC 61 100 SF INSTANTANEOUS FORWARD CURRENT. (A) INSTANTA NEOUS REVERSE CURRET . ( A) 1000 Tj=25oC Pulse Width=300 1% Duty Cycle .6 .8 1.0 1.2 1.4 1.6 s 1.8 FIG . 5 -MAXIMUM NON- REPETITIVE FORWARD SUREG CURRENT 175 200 150 180 125 FIG . 6 -TYPICAL JUNCTION CAPACITANCE JUNCTION CAPACITANCE(pF) PEAK FORWARD SURGE CURRENT . (A) PERCENT OF RATED PEAK REVERSE VOL. (% ) 8.3ms Single Half Sine Wave JEDEC Method 100 75 50 25 0 1 2 5 10 20 NUMBER OF CYCLES AT 60Hz 50 100 TJ=25 C O 160 S F6 140 120 100 S F6 80 60 .1 .5 5 -S 1 -S F64 F67 1 2 5 10 20 50 100 200 500 1000 REVERSE VOLTAGE ,(V)