KBU6005 THRU KBU610 SILICON BRIDGE RECTIFIERS Reverse Voltage - 50 to 1000 Volts Forward Current - 6.0 Amperes KBU 0.935(23.7) 0.895(22.7) FEATURES 0.15 x0.23L (3.8 x5.7L) HOLE THRU The plastic package carries Underwriters Laboratory Flammability Classification 94V-0 Ideal for printed circuit boards Low reverse leakage High forward surge current capability High temperature soldering guaranteed: 260 C/10 seconds,0.375”(9.5mm) lead length, 5 lbs. (2.3kg) tension 0.300 (7.5) 0.700(17.8) 0.600(16.8) 0.780(19.8) 0.740(18.8) AC 0.866 MIN. (22.0) MECHANICAL DATA 0.052(1.3) DIA. 0.048(1.2) Case: Molded plastic body Terminals: Plated leads solderable per MIL-STD-750, Method 2026 Polarity: Polarity symbols marked on case Mounting:Thru hole for #6 serew,5in.-lbs. torque max. Weight:0.27 ounce, 7.59 grams 0.220(5.6) 0.180(4.6) 0.140 (3.5) 0.280(7.1) 0.268(6.8) Dimensions in inches and (millimeters) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25 C ambient temperature unless otherwise specified. Single phase half-wave 60Hz,resistive or inductive load,for capacitive load current derate by 20%. MDD Catalog Number Maximum repetitive peak reverse voltage Maximum RMS voltage Maximum DC blocking voltage Maximum average forward TA=100 C(Note 2) output rectified current at TA=40 C(Note 2) Peak forward surge current 8.3ms single half sine-wave superimposed on rated load (JEDEC Method) Rating for Fusing(t<8.3ms) Maximum instantaneous forward voltage drop per birdge element at 6.0A Maximum DC reverse current TA=25 C at rated DC blocking voltage TA=100 C Typical Junction Capacitance (Note 1) Typical Thermal Resistance (Note 2) Operating junction temperature range storage temperature range SYMBOLS KBU 6005 KBU 601 KBU 602 KBU 604 KBU 606 KBU 608 KBU 610 UNITS VRRM VRMS VDC 50 35 50 100 70 100 200 140 200 400 280 400 600 420 600 800 560 800 1000 700 1000 VOLTS VOLTS VOLTS I(AV) 6.0 Amps IFSM 250.0 Amps I2t 260 A2s VF 1.0 Volts 10 1.0 200 4.7 -65 to +150 -65 to +150 µA mA pF C/W C C IR CJ RθJA TJ TSTG NOTES: 1.Measured at 1.0 MHz and applied reverse voltage of 4.0 Volts. 2.Unit mounted on 2.6” x 1.4” x0.06” thick(6.3x3.5x0.15cm)Al.plate. 3.Unit mounted on P.C. board with 0.5” x 0.5”(12x12mm) copper pads. MDD ELECTRONIC FIG. 1- FORWARD CURRENT DERATING CURVE 6.0 4.8 3.6 Single Phase Half Wave 60Hz Resistive or inductive Load 2.4 1.2 0 0 25 50 75 100 125 150 PEAK FORWARD SURGE CURRENT, AMPERES AVERAGE FORWARD RECTIFIED CURRENT, AMPERES RATINGS AND CHARACTERISTIC CURVES KBU6005 THRU KBU610 FIG. 2-MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT 250 200 150 100 8.3ms SINGLE HALF SINE-WAVE (JEDEC Method) 50 175 0 1 10 AMBIENT TEMPERATURE, C 20 10 1 TJ=25 C PULSE WIDTH=300 µs 1%DUTY CYCLE 0.01 0.6 0.8 1.0 1.2 1.4 1.5 FIG. 4-TYPICAL REVERSE CHARACTERISTICS INSTANTANEOUS REVERSE CURRENT, MICROAMPERES INSTANTANEOUS FORWARD CURRENT,AMPERES FIG. 3-TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS 0.1 1,000 100 TJ=100 C 10 1 0.1 0.01 INSTANTANEOUS FORWARD VOLTAGE, VOLTS TJ=25 C 0 20 40 60 80 400 40 TJ=25 C TRANSIENT THERMAL IMPEDANCE, C/W 800 FIG. 6-TYPICAL TRANSIENT THERMAL IMPEDANCE 100 10 1 0.1 0.01 0.1 1 10 4 0.1 1.0 10 100 PERCENT OF PEAK REVERSE VOLTAGE,% FIG. 5-TYPICAL JUNCTION CAPACITANCE JUNCTION CAPACITANCE, pF 100 NUMBER OF CYCLES AT 60 Hz 100 REVERSE VOLTAGE,VOLTS MDD ELECTRONIC t,PULSE DURATION,sec. 100