W005 THRU W10 SILICON BRIDGE RECTIFIERS Reverse Voltage - 50 to 1000 Volts WOM FEATURES 0.366(9.3) 0.350(8.9) The plastic package carries Underwriters Laboratory Flammability Classification 94V-0 Ideal for printed circuit boards Low reverse leakage High forward surge current capability High temperature soldering guaranteed: 260 C/10 seconds,0.375”(9.5mm) lead length, 5 lbs. (2.3kg) tension 0.237(6.0) 0.197(5.0) 1.1 (27.9) MIN. POS.LEAD Forward Current - 1.5 Amperes 1.0 (25.4) MIN. MECHANICAL DATA 0.032(0.8) DIA. 0.028(0.7) Case: Molded plastic body Terminals: Plated leads solderable per MIL-STD-750, Method 2026 Polarity: Polarity symbols marked on case Mounting Position: Any Weight:0.042 ounce, 1.2 grams 0.220(5.6) 0.180(4.6) 0.220(5.6) 0.180(4.6) Dimensions in inches and (millimeters) MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25 C ambient temperature unless otherwise specified. Single phase half-wave 60Hz,resistive or inductive load, for capacitive load current derate by 20%. W08 W10 UNITS Maximum repetitive peak reverse voltage VRRM 50 100 200 400 600 800 Maximum RMS voltage VRMS 35 70 140 280 420 560 Maximum DC blocking voltage VDC 50 100 200 400 600 800 Maximum average forward output rectified current I(AV) 1.5 at TA=25 C (Note 2) Peak forward surge current 8.3ms single half sine-wave superimposed on 50.0 IFSM rated load (JEDEC Method) Rating for Fusing(t<8.3ms) 10 I2t Maximum instantaneous forward voltage drop VF 1.0 per birdge element at 1.0A Maximum DC reverse current TA=25 C 10 IR at rated DC blocking voltage TA=100 C 0.5 Typical Junction Capacitance (Note 1) CJ 15 Typical Thermal Resistance RθJA 40 Operating junction temperature range TJ -55 to +125 storage temperature range TSTG -55 to +150 NOTES: 1.Measured at 1.0 MHz and applied reverse voltage of 4.0 Volts. 2.Unit mounted on P.C. board with 0.22” x 0.22”(5.5x5.5mm) copper pads,0.375”(9.5mm) lead length. 1000 700 1000 VOLTS VOLTS VOLTS MDD Catalog Number SYMBOLS W005 W01 W02 MDD ELECTRONIC W04 W06 Amps Amps A2s Volts µA mA pF C/W C C FIG. 1- FORWARD CURRENT DERATING CURVE 1.5 1.2 0.9 Single Phase Half Wave 60Hz Resistive or inductive Load 0.6 0.3 0 0 25 50 75 100 125 150 PEAK FORWARD SURGE CURRENT, AMPERES AVERAGE FORWARD RECTIFIED CURRENT, AMPERES RATINGS AND CHARACTERISTIC CURVES W005 THRU W10 FIG. 2-MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT 50 40 30 20 10 175 0 8.3ms SINGLE HALF SINE-WAVE (JEDEC Method) 1 10 AMBIENT TEMPERATURE, C 20 10 1 TJ=25 C PULSE WIDTH=300 µs 1%DUTY CYCLE 0.01 0.6 0.8 1.0 1.2 1.4 1.5 FIG. 4-TYPICAL REVERSE CHARACTERISTICS INSTANTANEOUS REVERSE CURRENT, MICROAMPERES INSTANTANEOUS FORWARD CURRENT,AMPERES FIG. 3-TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS 0.1 1,000 100 10 TJ=25 C 0.1 0.01 0 20 40 60 80 TJ=25 C 10 TRANSIENT THERMAL IMPEDANCE, C/W 200 FIG. 6-TYPICAL TRANSIENT THERMAL IMPEDANCE 100 10 1 0.1 0.01 0.1 1 10 1 0.1 1.0 10 100 PERCENT OF PEAK REVERSE VOLTAGE,% FIG. 5-TYPICAL JUNCTION CAPACITANCE JUNCTION CAPACITANCE, pF TJ=100 C 1 INSTANTANEOUS FORWARD VOLTAGE, VOLTS 100 100 NUMBER OF CYCLES AT 60 Hz 100 REVERSE VOLTAGE,VOLTS MDD ELECTRONIC t,PULSE DURATION,sec. 100