QPI-X-EVAL1

®
QPI-X-EVAL1
QuietPower ™
Evaluation Board for QPI Series Active EMI Filters
The QPI-x-EVAL1 [“x” refers to the specific QPI model]
is an easy to use evaluation board for testing the QPI
family of active EMI filters. The board can be used in
different EMI configurations (Figures 1 and 2), with
many of the standard DC to DC converters available.
Consult the converter’s manufacturer’s
recommendation for proper EMI re-circulation. The
evaluation board includes a mounted QPI filter, input
and output capacitors, and terminals blocks for easy
electrical connection.
When using the QPI-x-EVAL1 evaluation board, close
attention must be paid to wiring and grounding. Wires
should be kept as short as possible and positioned to
minimize radiated noise pick up around the QPI filter.
Refer to Picor’s QPI-AN1 application note for proper
EMI measurement set up.
Input BUS
Filter performance in the application is highly
dependent on several factors and cannot be
extrapolated from insertion loss curves alone. Final
noise performance is a complex function of filter
elements, equipment grounding and noise source
impedances, which vary in magnitude and phase over
the frequency spectrum of interest.
Designers should be aware that to select and quantify
an EMI filter for conducted noise, they must test the
filter in their product under the set up and conditions
specified in the applicable EMI standards.
Measurements should be made in consultation with
in-house compliance testing or an independent EMI
test facility.
Check www.picorpower.com for data sheets,
application notes and additional product information.
Converter
+
CY
+
C1
QPI
-
DC/DC
C2
-
CY
SHIELD
SHIELD
QPI-Active EVAL1
Figure 1 - Typical for “Open-frame” EMI topology
Input BUS
SHIELD Plane
Converter
+
+
C1
-
C2
QPI
DC/DC
CY
SHIELD
CY
CY
CY
SHIELD
QPI-Active EVAL1
Figure 2 - Typical for “Base-plate” EMI topology
Picor Corporation • www.picorpower.com
QPI-X-EVAL1 Data Sheet Rev. 1.3 Page 1 of 2
Thermal2
IN-
OUT+
9
8
7
BUSBUSBUS-
1
5
Input BUS
C2
47uF
QPIQPIQPI-
SHIELD
2
15
16
1
SHIELD
3
QPI+
QPI+
QPI+
QPI
C1
47uF
J1
Thermal
BUS+
BUS+
BUS+
Thermal
12
13
14
J2
1
4
3
2
OUT-
2
3
Converter
6
IN+
11
10
Thermal1
SHIELD
Figure 3 - QPI-X EVAL1 schematic.
Note: C1 and C2 are 47 µF, 100 V Capacitors
Figure 4 - QPI-X EVAL board showing location of components and connectors.
Ordering Information
Part Number
Description
Part Number
Description
QPI-3-EVAL1
Evaluation board for QPI-3LZ
QPI-5-EVAL1
Evaluation board for QPI-5LZ
QPI-4-EVAL1
Evaluation board for QPI-4LZ
QPI-6-EVAL1
Evaluation board for QPI-6LZ
Vicor’s comprehensive line of power solutions includes high-density AC-DC & DC-DC modules and accessory
components, fully configurable AC-DC & DC-DC power supplies, and complete custom power systems.
Information furnished by Vicor is believed to be accurate and reliable. However, no responsibility is assumed by Vicor for its
use. No license is granted by implication or otherwise under any patent or patent rights of Vicor. Vicor components are not
designed to be used in applications, such as life support systems, wherein a failure or malfunction could result in injury or
death. All sales are subject to Vicor’s Terms and Conditions of Sale, which are available upon request.
Specifications are subject to change without notice.
Vicor Corporation
25 Frontage Road, Andover, MA, USA 01810
Tel: 800-735-6200 Fax: 978-475-6715
Picor Corporation • www.picorpower.com • QPI-X-EVAL1 Data Sheet
Email
Vicor Express: [email protected]
Technical Support: [email protected]
Rev. 1.3
4/08