CP2104 S INGLE - C HIP USB- T O -UART B RIDGE Single-Chip USB to UART Data Transfer Integrated Virtual COM Port Device Drivers USB transceiver; no external resistors Works required Integrated clock; no external crystal required Integrated 1024-Byte One-Time Programmable ROM for customizable product information On-chip power-on reset circuit On-chip voltage regulator: 3.45 V output Windows Mac OS-X USBXpress™ Direct Driver Support Royalty-Free USB Specification 2.0 compliant; full-speed (12 Mbps) USB Suspend states supported via SUSPEND and SUSPEND pins Windows Distribution License 7/Vista/XP/Server 2003/2000 Windows CE® 6.0, 5.0, and 4.2 Example Applications Asynchronous Serial Data BUS (UART) Upgrade of RS-232 legacy devices to USB of RS-485 legacy devices to USB Cellular phone USB interface cable PDA USB interface cable USB to RS-232 serial adapter All handshaking and modem interface signals Data formats supported: - Data bits: 5, 6, 7, and 8 - Stop bits: 1, 1.5, and 2 - Parity: odd, even, mark, space, no parity Baud rates: 300 bps to 2 Mbits 576 byte receive buffer; 576 byte transmit buffer Hardware or X-On/X-Off handshaking supported Four GPIO signals for status and control Configurable I/O (1.8 V to VDD) using VIO pin RS-485 ® 7®/Vista®/XP®/Server 2003®/2000® ® Linux USB Function Controller Configurable with Existing COM Port PC Applications Distribution License Royalty-Free Upgrade Supply Voltage Self-powered: 3.0 to 3.6 V bus powered: 4.0 to 5.25 V I/O voltage: 1.8 V to VDD USB Package I/O (VDD to 5 V) using external pull-up RoHS-compliant mode with bus transceiver control 24-pin QFN (4x4 mm) Ordering Part Number CP2104-F03-GM Temperature Range: –40 to +85 °C External voltage supply or direct connection to VDD CP2104 GPIO.0 VIO GPIO.1 GPIO.2 (to external circuitry for status and control) 4 REGIN IN GPIO.3 Voltage Regulator RST OUT SUSPEND VDD GND USB CONNECTOR VBUS DD+ GND SUSPEND 48 MHz Oscillator RI DCD VBUS DTR DD+ USB Transceiver USB Function Controller DSR UART TXD 1024B PROM VPP (to external circuitry for USB suspend states) 576B 576B TX RX Buffer Buffer External RS-232 transceiver or UART circuitry RXD RTS CTS Figure 1. Example System Diagram Rev. 1.1 11/13 Copyright © 2013 by Silicon Laboratories CP2104 CP2104 2 Rev. 1.1 CP2104 TABLE O F C ONTENTS Section Page 1. System Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4 2. Electrical Characteristics . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .5 3. Pinout and Package Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8 4. QFN-24 Package Specifications . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10 5. USB Function Controller and Transceiver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 6. Asynchronous Serial Data Bus (UART) Interface . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 6.1. Baud Rate Generation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 7. GPIO Pins . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 13 7.1. GPIO.0-1—Transmit and Receive Toggle . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 7.2. GPIO.2—RS-485 Transceiver Bus Control . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 7.3. Hardware Flow Control (RTS and CTS) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15 8. One-Time Programmable ROM . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 9. Voltage Regulator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17 10. CP2104 Device Drivers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 10.1. Virtual COM Port Drivers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 10.2. USBXpress Drivers . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .19 10.3. Driver Customization . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 10.4. Driver Certification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 11. Relevant Application Notes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20 Document Change List . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21 Contact Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22 Rev. 1.1 3 CP2104 1. System Overview The CP2104 is a highly-integrated USB-to-UART Bridge Controller providing a simple solution for updating RS-232/RS-485 designs to USB using a minimum of components and PCB space. The CP2104 includes a USB 2.0 full-speed function controller, USB transceiver, oscillator, one-time programmable ROM, and asynchronous serial data bus (UART) with full modem control signals in a compact 4 x 4 mm QFN-24 package (sometimes called “MLF” or “MLP”). No other external USB components are required. The on-chip one-time programmable ROM may be used to customize the USB Vendor ID, Product ID, Product Description String, Power Descriptor, Device Release Number, Device Serial Number, and GPIO configuration as desired for OEM applications. Royalty-free Virtual COM Port (VCP) device drivers provided by Silicon Labs allow a CP2104-based product to appear as a COM port to PC applications. The CP2104 UART interface implements all RS-232/RS-485 signals, including control and handshaking signals, so existing system firmware does not need to be modified. The device also features up to four GPIO signals that can be user-defined for status and control information. Support for I/O interface voltages down to 1.8 V is provided via a VIO pin. In many existing RS-232 designs, all that is required to update the design from RS-232 to USB is to replace the RS-232 level-translator with the CP2104. Direct access driver support is available through the Silicon Labs USBXpress driver set. See www.siliconlabs.com for the latest application notes and product support information for the CP2104. An evaluation kit for the CP2104 (Part Number: CP2104EK) is available. It includes a CP2104-based USB-toUART/RS-232 evaluation board, a complete set of VCP device drivers, USB and RS-232 cables, and full documentation. Contact a Silicon Labs sales representatives or go to www.siliconlabs.com to order the CP2104 Evaluation Kit. 4 Rev. 1.1 CP2104 2. Electrical Characteristics Table 1. Absolute Maximum Ratings Parameter Conditions Min Typ Max Units Ambient Temperature Under Bias –55 — 125 °C Storage Temperature –65 — 150 °C VIO > 2.2 V VIO < 2.2 V –0.3 –0.3 — — 5.8 VIO + 3.6 V VDD > 3.0 V VDD not powered –0.3 –0.3 — — 5.8 VDD + 3.6 V –0.3 — 4.2 V Maximum Total Current through VDD, VIO, and GND — — 500 mA Maximum Output Current Sunk by RST or any I/O pin — — 100 mA Voltage on RST, GPIO or UART Pin with respect to GND Voltage on VBUS with respect to GND Voltage on VDD or VIO with respect to GND Note: Stresses above those listed may cause permanent damage to the device. This is a stress rating only, and functional operation of the devices at or exceeding the conditions in the operation listings of this specification is not implied. Exposure to maximum rating conditions for extended periods may affect device reliability. Table 2. Global DC Electrical Characteristics VDD = 3.0 to 3.6 V, –40 to +85 °C unless otherwise specified. Parameter Min Typ Max Units Digital Supply Voltage (VDD) 3.0 — 3.6 V Digital Port I/O Supply Voltage (VIO) 1.8 — VDD V 5.75 — VIO + 3.6 V — 4.7 — µF Voltage on VPP with respect to GND during a ROM programming operation Conditions VIO > 3.3 V Capacitor on VPP for ROM programming Supply Current1 Normal Operation; VREG Enabled — 17.0 18.5 mA Supply Current1 Suspended; VREG Enabled — 100 200 µA — 200 228 µA –40 — +85 °C Supply Current—USB Pull-up2 Specified Operating Temperature Range Notes: 1. If the device is connected to the USB bus, the USB Pull-up Current should be added to the supply current for total supply current. 2. The USB Pull-up supply current values are calculated values based on USB specifications. Rev. 1.1 5 CP2104 Table 3. UART and Suspend I/O DC Electrical Characteristics VDD = 3.0 to 3.6 V, VIO = 1.8 V to VDD, –40 to +85 °C unless otherwise specified. Parameters Conditions Min Typ Max UNITS IOH = –10 µA IOH = –3 mA IOH = –10 mA VIO – 0.1 VIO – 0.2 — — — VIO – 0.4 — — — V IOL = 10 µA IOL = 8.5 mA IOL = 25 mA — — — — — 0.6 0.1 0.4 — V Input High Voltage (VIH) 0.7 x VIO — — V Input Low Voltage (VIL) — — 0.6 V Output High Voltage (VOH) Output Low Voltage (VOL) Input Leakage Current Weak Pull-Up Off Weak Pull-Up On, VIN = 0 V — — — 25 1 50 µA Maximum Input Voltage Open drain, logic high (1) — — 5.8 V Min Typ Max Units RST Input High Voltage 0.75 x VIO — — V RST Input Low Voltage — — 0.6 V Minimum RST Low Time to Generate a System Reset 15 — — µs VDD Ramp Time for Power On — — 1 ms Table 4. Reset Electrical Characteristics –40 to +85 °C unless otherwise specified. Parameter Conditions Table 5. Voltage Regulator Electrical Specifications –40 to +85 °C unless otherwise specified. Parameter Conditions Min Typ Max Units 3.0 — 5.25 V 3.3 3.45 3.6 V VBUS Detection Input Threshold 2.5 — — V Bias Current — — 120 µA Input Voltage Range Output Voltage Output Current = 1 to 100 mA* *Note: The maximum regulator supply current is 100 mA. This includes the supply current of the CP2104. 6 Rev. 1.1 CP2104 Table 6. GPIO Output Specifications –40 to +85 °C unless otherwise specified Parameter Conditions Min Typ Max Units RS-485 Active Time After Stop Bit — 1 — bit time* TX Toggle Rate — 10 — Hz RX Toggle Rate — 10 — Hz *Note: Bit-time is calculated as 1 / baud rate. Rev. 1.1 7 CP2104 3. Pinout and Package Definitions Table 7. CP2104 Pin Definitions Name Pin # Type VDD 6 Power In Description Power Supply Voltage Input. Power Out Voltage Regulator Output. See Section 9. I/O Supply Voltage Input. VIO 5 GND 2 RST 9 D I/O Device Reset. Open-drain output of internal POR or VDD monitor. An external source can initiate a system reset by driving this pin low for the time specified in Table 4. REGIN 7 Power In 5 V Regulator Input. This pin is the input to the on-chip voltage regulator. VBUS 8 D In VBUS Sense Input. This pin should be connected to the VBUS signal of a USB network. VPP 16* Special D+ 3 D I/O USB D+ D– 4 D I/O USB D– TXD 21 D Out Asynchronous data output (UART Transmit) RXD 20 D In Asynchronous data input (UART Receive) CTS 18* D In Clear to Send control input (active low) RTS 19* D Out Ready to Send control output (active low) DSR 22* D In Data Set Ready control input (active low) DTR 23* D Out DCD 24* D In Data Carrier Detect control input (active low) RI 1* D In Ring Indicator control input (active low) SUSPEND 17* D Out This pin is logic high when the CP2104 is in the USB Suspend state. SUSPEND 15* D Out This pin is logic low when the CP2104 is in the USB Suspend state. GPIO.3 11* D I/O User-configurable input or output. GPIO.2 12* D I/O User-configurable input or output. GPIO.1 13* D I/O User-configurable input or output. GPIO.0 14* D I/O User-configurable input or output. NC 10* Power In Ground. Must be tied to ground. Connect a 4.7 µF capacitor between this pin and ground to support ROM programming via USB interface. Data Terminal Ready control output (active low) This pin should be left unconnected or tied to VIO. *Note: Pins can be left unconnected when not used. 8 Rev. 1.1 DCD DTR DSR TXD RXD RTS 24 23 22 21 20 19 CP2104 RI 1 18 CTS GND 2 17 SUSPEND D+ 3 16 VPP D- 4 15 SUSPEND VIO 5 14 GPIO.0 VDD 6 13 GPIO.1 CP2104-GM Top View 11 12 GPIO.3 GPIO.2 9 RST 10 8 VBUS NC 7 REGIN GND (Optional) Figure 2. QFN-24 Pinout Diagram (Top View) Rev. 1.1 9 CP2104 4. QFN-24 Package Specifications Figure 3. QFN-24 Package Drawing Table 8. QFN-24 Package Dimensions Dimension Min Typ Max Dimension Min Typ Max A A1 b D D2 e E E2 0.70 0.00 0.18 0.75 0.02 0.25 4.00 BSC. 2.70 0.50 BSC. 4.00 BSC. 2.70 0.80 0.05 0.30 L L1 aaa bbb ddd eee Z Y 0.30 0.00 — — — — — — 0.40 — — — — — 0.24 0.18 0.50 0.15 0.15 0.10 0.05 0.08 — — 2.55 2.55 2.80 2.80 Notes: 1. All dimensions shown are in millimeters (mm) unless otherwise noted. 2. Dimensioning and Tolerancing per ANSI Y14.5M-1994. 3. This drawing conforms to JEDEC Solid State Outline MO-220, variation WGGD except for custom features D2, E2, Z, Y, and L which are toleranced per supplier designation. 4. Recommended card reflow profile is per the JEDEC/IPC J-STD-020 specification for Small Body Components. 10 Rev. 1.1 CP2104 Figure 4. QFN-24 Recommended PCB Land Pattern Table 9. QFN-24 PCB Land Pattern Dimensions Dimension Min Max Dimension Min Max C1 C2 E X1 3.90 3.90 4.00 4.00 X2 Y1 Y2 2.70 0.65 2.70 2.80 0.75 2.80 0.50 BSC 0.20 0.30 Notes: General 1. All dimensions shown are in millimeters (mm) unless otherwise noted. 2. This Land Pattern Design is based on the IPC-7351 guidelines. Solder Mask Design 3. All metal pads are to be non-solder mask defined (NSMD). Clearance between the solder mask and the metal pad is to be 60 m minimum, all the way around the pad. Stencil Design 4. A stainless steel, laser-cut and electro-polished stencil with trapezoidal walls should be used to assure good solder paste release. 5. The stencil thickness should be 0.125 mm (5 mils). 6. The ratio of stencil aperture to land pad size should be 1:1 for all perimeter pads. 7. A 2x2 array of 1.10 mm x 1.10 mm openings on a 1.30 mm pitch should be used for the center pad. Card Assembly 8. A No-Clean, Type-3 solder paste is recommended. 9. The recommended card reflow profile is per the JEDEC/IPC J-STD-020 specification for Small Body Components. Rev. 1.1 11 CP2104 5. USB Function Controller and Transceiver The Universal Serial Bus (USB) function controller in the CP2104 is a USB 2.0 compliant full-speed device with integrated transceiver and on-chip matching and pullup resistors. The USB function controller manages all data transfers between the USB and the UART as well as command requests generated by the USB host controller and commands for controlling the function of the UART and GPIO pins. The USB Suspend and Resume signals are supported for power management of both the CP2104 device as well as external circuitry. The CP2104 will enter Suspend mode when Suspend signaling is detected on the bus. On entering Suspend mode, the CP2104 asserts the SUSPEND and SUSPEND signals. SUSPEND and SUSPEND are also asserted after a CP2104 reset until device configuration during USB Enumeration is complete. The CP2104 exits the Suspend mode when any of the following occur: Resume signaling is detected or generated, a USB Reset signal is detected, or a device reset occurs. On exit of Suspend mode, the SUSPEND and SUSPEND signals are de-asserted. Both SUSPEND and SUSPEND temporarily float high during a CP2104 reset. If this behavior is undesirable, a strong pulldown (10 k) can be used to ensure SUSPEND remains low during reset. The logic level and output mode (push-pull or open-drain) of various pins during USB Suspend is configurable in the PROM. See Section 8 for more information. 6. Asynchronous Serial Data Bus (UART) Interface The CP2104 UART interface consists of the TX (transmit) and RX (receive) data signals as well as the RTS, CTS, DSR, DTR, DCD, and RI control signals. The UART supports RTS/CTS, DSR/DTR, and X-On/X-Off handshaking. The UART is programmable to support a variety of data formats and baud rates. If the Virtual COM Port drivers are used, the data format and baud rate are set during COM port configuration on the PC. If the USBXpress drivers are used, the CP2104 is configured through the USBXpress API. The data formats and baud rates available are listed in Table 10. Table 10. Data Formats and Baud Rates Data Bits1 5, 6, 7, and 8 Stop Bits 1, 1.52, and 2 Parity Type None, Even, Odd, Mark, Space Baud Rates 300 bps to 2.0 Mbps Notes: 1. Data sizes of 5 and 6 bits are not supported at baud rates above 921600 bps. 2. 1.5 stop bits only available when using 5 data bits. 12 Rev. 1.1 CP2104 6.1. Baud Rate Generation The baud rate generator is very flexible, allowing the user to request any baud rate in the range from 300 bps to 2 Mbps. If the baud rate cannot be directly generated from the 48 MHz oscillator, the device will choose the closest possible option. The actual baud rate is dictated by Equation 1 and Equation 2. Prescale = 4 if Requested Baud Rate 365 bps Prescale = 1 if Requested Baud Rate 365 bps 48 MHz Clock Divider = ---------------------------------------------------------------------------------------------------2 Prescale Requested Baud Rate Equation 1. Clock Divider Calculation 48 MHz Actual Baud Rate = ----------------------------------------------------------------------------2 Prescale Clock Divider Prescale = 4 if Requested Baud Rate 365 bps Prescale = 1 if Requested Baud Rate 365 bps Equation 2. Baud Rate Calculation Most baud rates can be generated with an error of less than 1.0%. A general rule of thumb for the majority of UART applications is to limit the baud rate error on both the transmitter and the receiver to no more than ±2%. The clock divider value obtained in Equation 1 is rounded to the nearest integer, which may produce an error source. Another error source will be the 48 MHz oscillator, which is accurate to ±0.25%. Knowing the actual and requested baud rates, the total baud rate error can be found using Equation 3. Actual Baud Rate Baud Rate Error (%) = 100 1 – ----------------------------------------------------------- 0.25% Requested Baud Rate Equation 3. Baud Rate Error Calculation 7. GPIO Pins The CP2104 supports four user-configurable GPIO pins for status and control information. Each of these GPIO pins are usable as inputs, open-drain outputs, or push-pull outputs. Three of these GPIO pins also have alternate functions which are listed in Table 11. Table 11. GPIO Pin Alternate Functions GPIO Pin Alternate Function GPIO.0 TX Toggle GPIO.1 RX Toggle GPIO.2 RS-485 Transceiver Control By default, all of the GPIO pins are configured as a GPIO input. The configuration of the pins is one-time programmable for each device. The difference between an open-drain output and a push-pull output is when the GPIO output is driven to logic high. A logic high, open-drain output pulls the pin to the VIO rail through an internal, pull-up resistor. A logic high, push-pull output directly connects the pin to the VIO voltage. Open-drain outputs are typically used when interfacing to logic at a higher voltage than the VIO pin. These pins can be safely pulled to the higher, external voltage through an external pull-up resistor. The maximum external pull-up voltage is 5 V. The speed of reading and writing the GPIO pins is subject to the timing of the USB bus. GPIO pins configured as inputs or outputs are not recommended for real-time signaling. More information regarding the configuration and usage of these pins can be found in “AN721: CP21xx Device Customization Guide” and “AN223: Runtime GPIO Control for CP210x” available on the Silicon Labs website. Rev. 1.1 13 CP2104 7.1. GPIO.0-1—Transmit and Receive Toggle GPIO.0 and GPIO.1 are configurable as Transmit Toggle and Receive Toggle pins. These pins are logic high when a device is not transmitting or receiving data, and they toggle at a fixed rate as specified in Table 6 when data transfer is in progress. Typically, these pins are connected to two LEDs to indicate data transfer. VIO CP2104 GPIO.0 – TX Toggle GPIO.1 – RX Toggle Figure 5. Transmit and Receive Toggle Typical Connection Diagram 7.2. GPIO.2—RS-485 Transceiver Bus Control GPIO.2 is configurable as an RS-485 bus transceiver control pin which is connected to the DE and RE inputs of the transceiver. When configured for RS-485 mode, the pin is asserted during UART data transmission as well as line break transmission. The RS-485 mode of GPIO.2 is active-high by default, and is also configurable for active-low mode. CP2104 RS-485 Transceiver TX R RX D GPIO.2 – RS485 RE DE Figure 6. RS-485 Transceiver Typical Connection Diagram 14 Rev. 1.1 CP2104 7.3. Hardware Flow Control (RTS and CTS) To utilize the functionality of the RTS and CTS pins of the CP2104, the device must be configured to use hardware flow control. RTS, or Ready To Send, is an active-low output from the CP2104 and indicates to the external UART device that the CP2104’s UART RX FIFO has not reached the watermark level of 383 bytes and is ready to accept more data. When the amount of data in the RX FIFO reaches the watermark, the CP2104 pulls RTS high to indicate to the external UART device to stop sending data. CTS, or Clear To Send, is an active-low input to the CP2104 and is used by the external UART device to indicate to the CP2104 when the external UART device’s RX FIFO is getting full. The CP2104 will not send more than two bytes of data once CTS is pulled high. CP2104 RS232 System TX TX RX RX RTS RTS CTS CTS Figure 7. Hardware Flow Control Typical Connection Diagram Rev. 1.1 15 CP2104 8. One-Time Programmable ROM The CP2104 includes an internal one-time programmable ROM that may be used to customize the USB Vendor ID (VID), Product ID (PID), Product Description String, Power Descriptor, Device Release Number, Device Serial Number, GPIO configuration, Suspend pins, and modes as desired for OEM applications. If the programmable ROM has not been customized, the default configuration data shown in Table 12 and Table 13 is used. Table 12. Default USB Configuration Data Name Value Vendor ID 10C4h Product ID EA60h Power Descriptor (Attributes) 80h (Bus-powered) Power Descriptor (Max. Power) 32h (100 mA) Release Number 0100h (Release Version 01.00) Serial Number Unique 8 character ASCII string (63 characters maximum) Product Description String “CP2104 USB to UART Bridge Controller” (126 characters maximum) Table 13. Default GPIO, UART, and Suspend Configuration Data Name Value GPIO.0 GPIO Input GPIO.1 GPIO Input GPIO.2 GPIO Input GPIO.3 GPIO Input Flush_Buffers Flush TX and RX FIFO on open SUSPEND Push-pull SUSPEND Push-pull RS-485 Level Active-High While customization of the USB configuration data is optional, customizing the VID/PID combination is recommended. A unique VID/PID combination will prevent the driver from conflicting with any other USB driver. A vendor ID can be obtained from www.usb.org or Silicon Labs can provide a free PID for the OEM product that can be used with the Silicon Labs VID. Customizing the serial number is also recommended if the OEM application is one in which it is possible for multiple CP210x-based devices to be connected to the same PC. The configuration data ROM can be programmed by Silicon Labs prior to shipment with the desired configuration information. It can also be programmed in-system over the USB interface by adding a capacitor to the PCB. If configuration ROM is to be programmed in-system, a 4.7 µF capacitor must be added between the VPP pin and ground. No other circuitry should be connected to VPP during a programming operation, and VDD must remain at 3.3 V or higher to successfully write to the configuration ROM. 16 Rev. 1.1 CP2104 9. Voltage Regulator The CP2104 includes an on-chip 5.0 to 3.45 V voltage regulator. This allows the CP2104 to be configured as either a USB bus-powered device or a USB self-powered device. A typical connection diagram of the device in a buspowered application using the regulator is shown in Figure 8. When enabled, the voltage regulator output appears on the VDD pin and can be used to power external devices. See Table 5 for the voltage regulator electrical characteristics. If the regulator is used to provide VDD in a self-powered application, use the same connections from Figure 8, but connect REGIN to an onboard 5 V supply, and disconnect it from the VBUS pin. In addition, if REGIN may be unpowered while VBUS is 5 V, a resistor divider shown in Note 5 of Figure 9 is required to meet the absolute maximum voltage on VBUS specification in Table 1. VIO Note 2 4.7 k Note 3 3.45 V Power 1-5 F VIO CP2104 VDD SUSPEND 0.1 F 1 F RST SUSPEND REGIN To external circuitry for USB suspend states GPIO.0 GPIO.1 GND GPIO.2 USB Connector To external circuitry for status and control GPIO.3 VBUS VBUS D+ D+ D- D- RI DCD GND DTR DSR TXD Note 1 4.7 F Standard UART Signals RXD VPP RTS CTS Note 4 Note 1 : Avalanche transient voltage suppression diodes compatible with Full-speed USB should be added at the connector for ESD protection. Use Littelfuse p/n SP0503BAHT or equivalent. Note 2 : An external pull-up is not required, but can be added for noise immunity. Note 3 : VIO can be connected directly to VDD or to a supply as low as 1.8 V to set the I/O interface voltage. Note 4 : If configuration ROM is to be programmed via USB, a 4.7 F capacitor must be added between VPP and ground. During a programming operation, the pin should not be connected to other circuitry, and VDD must be at least 3.3 V. Figure 8. Typical Bus-Powered Connection Diagram Rev. 1.1 17 CP2104 Alternatively, if 3.0 to 3.6 V power is supplied to the VDD pin, the CP2104 can function as a USB self-powered device with the voltage regulator bypassed. For this configuration, tie the REGIN input to VDD to bypass the voltage regulator. A typical connection diagram showing the device in a self-powered application with the regulator bypassed is shown in Figure 9. The USB max power and power attributes descriptor must match the device power usage and configuration. See application note “AN721: CP210x/CP211x Device Customization Guide” for information on how to customize USB descriptors for the CP2104. VIO Note 2 4.7 k Note 3 VIO CP2104 VDD RST SUSPEND SUSPEND 3.3 V Power To external circuitry for USB suspend states REGIN 1-5 F GPIO.0 0.1 F GPIO.1 GPIO.2 GND Note 5 (Optional) GPIO.3 24 k RI VBUS USB Connector To external circuitry for status and control DCD 47 k DTR VBUS DSR D+ D+ D- D- TXD Standard UART Signals RXD GND RTS CTS Note 1 4.7 F VPP Note 4 Note 1 : Avalanche transient voltage suppression diodes compatible with Full-speed USB should be added at the connector for ESD protection. Use Littelfuse p/n SP0503BAHT or equivalent. Note 2 : An external pull-up is not required, but can be added for noise immunity. Note 3 : VIO can be connected directly to VDD or to a supply as low as 1.8 V to set the I/O interface voltage. Note 4 : If configuration ROM is to be programmed via USB, a 4.7 F capacitor must be added between VPP and ground. During a programming operation, the pin should not be connected to other circuitry, and VDD must be at least 3.3 V. Note 5 : For self-powered systems where VDD and VIO may be unpowered when VBUS is connected to 5 V, a resistor divider (or functionally-equivalent circuit) on VBUS is required to meet the absolute maximum voltage on VBUS specification in the Electrical Characteristics section. Figure 9. Typical Self-Powered Connection Diagram (Regulator Bypass) 18 Rev. 1.1 CP2104 10. CP2104 Device Drivers There are two sets of device drivers available for CP2104 devices: the Virtual COM Port (VCP) drivers and the USBXpress Direct Access drivers. Only one set of drivers is necessary to interface with the device. The latest drivers are available at http://www.siliconlabs.com/products/mcu/Pages/SoftwareDownloads.aspx. 10.1. Virtual COM Port Drivers The CP2104 Virtual COM Port (VCP) device drivers allow a CP2104-based device to appear to the PC's application software as a COM port. Application software running on the PC accesses the CP2104-based device as it would access a standard hardware COM port. However, actual data transfer between the PC and the CP2104 device is performed over the USB interface. Therefore, existing COM port applications may be used to transfer data via the USB to the CP2104-based device without modifying the application. See application note “AN197: Serial Communications Guide for the CP210x” for Example Code for Interfacing to a CP2104 using the Virtual COM drivers. 10.2. USBXpress Drivers The Silicon Labs USBXpress drivers provide an alternate solution for interfacing with CP2104 devices. No serial port protocol expertise is required. Instead, a simple, high-level application program interface (API) is used to provide simpler CP210x connectivity and functionality. The USBXpress for CP210x Development Kit includes Windows device drivers, Windows device driver installer and uninstallers, and a host interface function library (host API) provided in the form of a Windows dynamic link library (DLL). The USBXpress driver set is recommended for new products that also include new PC software. The USBXpress interface is described in application note “AN169: USBXpress Programmer's Guide.” 10.3. Driver Customization In addition to customizing the device as described in "6. Asynchronous Serial Data Bus (UART) Interface" on page 12, the drivers and the drivers installation package can be also be customized. See application note “AN220: USB Driver Customization” for more information on generating customized VCP and USBXpress drivers. Important Note: The VID/PID in the drivers must match the VID/PID in the device for the drivers to load properly then the device is connected to the PC. 10.4. Driver Certification The default drivers that are shipped with the CP2104 are Microsoft Windows Hardware Quality Labs (WHQL) certified. The certification means that the drivers have been tested by Microsoft and their latest operating systems will allow the drivers to be installed without any warnings or errors. The customized drivers that are generated using the “AN220: USB Driver Customization” software are not automatically certified. To become certified, they must go first through the Microsoft Driver Reseller Submission process. Contact Silicon Labs support for assistance with this process. Rev. 1.1 19 CP2104 11. Relevant Application Notes The following Application Notes are applicable to the CP2104. The latest versions of these application notes and their accompanying software are available at http://www.siliconlabs.com/products/mcu/Pages/ApplicationNotes.aspx. 20 AN721: CP21xx Device Customization Guide—This application note describes how to use the AN721 software CP21xxCustomizationUtility to configure the USB parameters on the CP21xx devices. AN169: USBXpress Programmer's Guide—This application note describes the USBXpress API interface and includes example code. AN197: Serial Communications Guide for the CP210x—This application note describes how to use the standard Windows COM port function to communicate with the CP210x and includes example code. AN220: USB Driver Customization—This application note describes how to use the AN220 software to customize the VCP or USBXpress drivers with OEM information. AN223: Runtime GPIO Control for CP210x—This application note describes how to use the CP210xRuntime DLL to control the CP210x GPIO. Rev. 1.1 CP2104 DOCUMENT CHANGE LIST Revision 0.2 to Revision 0.3 Updated Figure 1, “Example System Diagram,” on page 1. Added Figure , “,” on page 11. Added Figure 8, “Typical Bus-Powered Connection Diagram,” on page 17. Added Figure 9, “Typical Self-Powered Connection Diagram (Regulator Bypass),” on page 18. Added "6.1. Baud Rate Generation" on page 13. Moved Table 5 to "2. Electrical Characteristics" on page 5. Revision 0.3 to Revision 0.4 Updated ordering part number on page 1. Updated self-powered supply voltage on page 1. Updated USB pull-up supply current in table 2. Updated output voltage in Table 5. Updated Table 7 pin descriptions. Updated Table 10 baud rates. Updated Figure 9. Revision 0.4 to Revision 1.0 Updated ordering part number on page 1. Updated electrical specifications throughout Section 2. Added Table 6 Updated Section 7. Updated Section 8. Added Table 11 and Table 13 Updated descriptions of figures in Section 9. Revision 1.0 to Revision 1.1 21 Added a row for VBUS in Table 1, “Absolute Maximum Ratings,” on page 5. Added VDD Ramp Time for Power On specification to Table 4, “Reset Electrical Characteristics,” on page 6. Added VPP Voltage and Capacitor specifications to Table 2, “Global DC Electrical Characteristics,” on page 5. Updated AN144 references to AN721. Updated "9. Voltage Regulator" on page 17 to add absolute maximum voltage on VBUS requirements in self-powered systems. Rev. 1.1 CP2104 CONTACT INFORMATION Silicon Laboratories Inc. 400 West Cesar Chavez Austin, TX 78701 Tel: 1+(512) 416-8500 Fax: 1+(512) 416-9669 Toll Free: 1+(877) 444-3032 Please visit the Silicon Labs Technical Support web page: https://www.silabs.com/support/pages/contacttechnicalsupport.aspx and register to submit a technical support request. Patent Notice Silicon Labs invests in research and development to help our customers differentiate in the market with innovative low-power, small size, analogintensive mixed-signal solutions. Silicon Labs' extensive patent portfolio is a testament to our unique approach and world-class engineering team. The information in this document is believed to be accurate in all respects at the time of publication but is subject to change without notice. Silicon Laboratories assumes no responsibility for errors and omissions, and disclaims responsibility for any consequences resulting from the use of information included herein. Additionally, Silicon Laboratories assumes no responsibility for the functioning of undescribed features or parameters. Silicon Laboratories reserves the right to make changes without further notice. Silicon Laboratories makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Silicon Laboratories assume any liability arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation consequential or incidental damages. Silicon Laboratories products are not designed, intended, or authorized for use in applications intended to support or sustain life, or for any other application in which the failure of the Silicon Laboratories product could create a situation where personal injury or death may occur. Should Buyer purchase or use Silicon Laboratories products for any such unintended or unauthorized application, Buyer shall indemnify and hold Silicon Laboratories harmless against all claims and damages. Silicon Laboratories and Silicon Labs are trademarks of Silicon Laboratories Inc. Other products or brandnames mentioned herein are trademarks or registered trademarks of their respective holders. 22 Rev. 1.1