ADT7410 (Rev. A)

±0.5°C Accurate, 16-Bit Digital
I2C Temperature Sensor
ADT7410
Data Sheet
FEATURES
Industrial process control
Power system monitors
Hand-held applications
High performance
Temperature accuracy
±0.5°C from −40°C to +105°C (2.7 V to 3.6 V)
±0.4°C from −40°C to +105°C (3.0 V)
16-bit temperature resolution: 0.0078°C
Fast first temperature conversion on power-up of 6 ms
Easy implementation
No temperature calibration/correction required by user
No linearity correction required
Low power
Power saving 1 sample per second (SPS) mode
700 µW typical at 3.3 V in normal mode
7 µW typical at 3.3 V in shutdown mode
Wide operating ranges
Temperature range: −55°C to +150°C
Voltage range: 2.7 V to 5.5 V
Programmable interrupts
Critical overtemperature interrupt
Overtemperature/undertemperature interrupt
I2C-compatible interface
8-lead narrow SOIC RoHS-compliant package
GENERAL DESCRIPTION
The ADT7410 is a high accuracy digital temperature sensor
in a narrow SOIC package. It contains a band gap temperature
reference and a 13 bit ADC to monitor and digitize the temperature to a 0.0625°C resolution. The ADC resolution, by default,
is set to 13 bits (0.0625°C). This can be changed to 16 bits
(0.0078°C) by setting Bit 7 in the configuration register
(Register Address 0x03).
The ADT7410 is guaranteed to operate over supply voltages from
2.7 V to 5.5 V. Operating at 3.3 V, the average supply current is typically 210 μA. The ADT7410 has a shutdown mode that powers
down the device and offers a shutdown current of typically 2 μA.
The ADT7410 is rated for operation over the −55°C to +150°C
temperature range.
Pin A0 and Pin A1 are available for address selection, giving the
ADT7410 four possible I2C® addresses. The CT pin is an opendrain output that becomes active when the temperature exceeds
a programmable critical temperature limit. The default critical
temperature limit is 147°C. The INT pin is also an open-drain
output that becomes active when the temperature exceeds a
programmable limit. The INT and CT pins can operate in either
comparator or interrupt mode.
APPLICATIONS
Medical equipment
Environmental control systems
Computer thermal monitoring
Thermal protection
FUNCTIONAL BLOCK DIAGRAM
VDD
8
TEMPERATURE
VALUE
REGISTER
ADT7410
INTERNAL
OSCILLATOR
CONFIGURATION
REGISTER
TCRIT
REGISTER
THIGH
REGISTER
6
CT
5
INT
1
SCL
2
SDA
TCRIT
INTERNAL
REFERENCE
Σ-Δ
MODULATOR
TEMPERATURE
SENSOR
THIGH
TLOW
REGISTER
A0
3
A1
4
POINTER
REGISTER
FILTER
LOGIC
I2C INTERFACE
7
GND
TLOW
06560-001
THYST
REGISTER
Figure 1.
Rev. A
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
www.analog.com
Fax: 781.461.3113 ©2009–2011 Analog Devices, Inc. All rights reserved.
ADT7410
Data Sheet
TABLE OF CONTENTS
Features .............................................................................................. 1
Temperature Value Registers .................................................... 13
Applications ....................................................................................... 1
Status Register ............................................................................. 14
General Description ......................................................................... 1
Configuration Register .............................................................. 14
Functional Block Diagram .............................................................. 1
THIGH Setpoint Registers ............................................................. 15
Revision History ............................................................................... 2
TLOW Setpoint Registers.............................................................. 15
Specifications..................................................................................... 3
TCRIT Setpoint Registers.............................................................. 15
I2C Timing Specifications ............................................................ 4
THYST Setpoint Register............................................................... 16
Absolute Maximum Ratings ............................................................ 5
ID Register................................................................................... 16
ESD Caution .................................................................................. 5
Serial Interface ................................................................................ 17
Pin Configuration and Function Descriptions ............................. 6
Serial Bus Address ...................................................................... 17
Typical Performance Characteristics ............................................. 7
Writing Data ............................................................................... 18
Theory of Operation ........................................................................ 9
Reading Data ............................................................................... 19
Circuit Information ...................................................................... 9
Reset ............................................................................................. 19
Converter Details.......................................................................... 9
General Call ................................................................................ 19
Temperature Measurement ......................................................... 9
INT and CT Outputs...................................................................... 21
One-Shot Mode .......................................................................... 10
Undertemperature and Overtemperature Detection ............ 21
1 SPS Mode .................................................................................. 10
Applications Information .............................................................. 23
Shutdown ..................................................................................... 11
Thermal Response Time ........................................................... 23
Fault Queue ................................................................................. 11
Supply Decoupling ..................................................................... 23
Temperature Data Format ......................................................... 12
Temperature Monitoring ........................................................... 23
Temperature Conversion Formulas ......................................... 12
Outline Dimensions ....................................................................... 24
Registers ........................................................................................... 13
Ordering Guide .......................................................................... 24
Address Pointer Register ........................................................... 13
REVISION HISTORY
12/11—Rev. 0 to Rev. A
Changes to Features Section............................................................ 1
Changes to Table 1 ............................................................................ 3
Changes to Figure 5 .......................................................................... 7
Changes to One-Shot Mode Section and 1 SPS Mode
Section .............................................................................................. 10
Changes to Shutdown Section ...................................................... 11
Changes to Table 8 and Table 9 ..................................................... 13
Changes to Table 10 and Table 11 ................................................ 14
Changes to Ordering Guide .......................................................... 24
4/09—Revision 0: Initial Version
Rev. A | Page 2 of 24
Data Sheet
ADT7410
SPECIFICATIONS
TA = −55°C to +150°C, VDD = 2.7 V to 5.5 V, unless otherwise noted.
Table 1.
Parameter
TEMPERATURE SENSOR AND ADC
Accuracy 1
Min
ADC Resolution
Temperature Resolution
13-Bit
16-Bit
Temperature Conversion Time
Fast Temperature Conversion Time
1 SPS Conversion Time
Temperature Hysteresis
Repeatability 3
DC PSRR
DIGITAL OUTPUTS (OPEN DRAIN)
High Output Leakage Current, IOH
Output High Current
Output Low Voltage, VOL
Output High Voltage, VOH
Output Capacitance, COUT
DIGITAL INPUTS
Input Current
Input Low Voltage, VIL
Input High Voltage, VIH
SCL, SDA Glitch Rejection
Pin Capacitance
POWER REQUIREMENTS
Supply Voltage
Supply Current
At 3.3 V
At 5.5 V
1 SPS Current
At 3.3 V
At 5.5 V
Shutdown Current
At 3.3 V
At 5.5 V
Power Dissipation Normal Mode
Power Dissipation 1 SPS
Typ
Max
Unit
Test Conditions/Comments
−0.05
±0.4 2
±0.44
±0.5
±0.5
±0.7
±0.8
±1.0
13
°C
°C
°C
°C
°C
°C
°C
Bits
16
Bits
TA = −40°C to +105°C, VDD = 3.0 V
TA = −40°C to +105°C, VDD = 2.7 V to 3.3 V
TA = −55°C to +125°C, VDD = 3.0 V
TA = −40°C to +105°C, VDD = 2.7 V to 3.6 V
TA = −55°C to +150°C, VDD = 2.7 V to 3.6 V
TA = −40°C to +105°C, VDD = 4.5 V to 5.5 V
TA = −55°C to +150°C, VDD = 2.7 V to 5.5 V
Twos complement temperature value of the sign bit
plus 12 ADC bits (power-up default resolution)
Twos complement temperature value of the sign bit
plus 15 ADC bits (Bit 7 = 1 in the configuration register)
0.0625
0.0078
240
6
60
±0.002
±0.015
0.1
°C
°C
ms
ms
ms
°C
°C
°C/V
13-bit resolution (sign + 12-bit)
16-bit resolution (sign + 15-bit)
Continuous conversion and one-shot conversion modes
First conversion on power-up only
Conversion time for 1 SPS mode
Temperature cycle = 25°C to 125°C and back to 25°C
TA = 25°C
TA = 25°C
5
1
0.4
µA
mA
V
V
pF
CT and INT pins pulled up to 5.5 V
VOH = 5.5 V
IOL = 2 mA @ 5.5 V, IOL = 1 mA @ 3.3 V
±1
0.4
VIN = 0 V to VDD
10
µA
V
V
ns
pF
5.5
V
250
300
µA
µA
Peak current while converting, I2C interface inactive
Peak current while converting, I2C interface inactive
µA
µA
VDD = 3.3 V, 1 SPS mode, TA = 25°C
VDD = 5.5 V, 1 SPS mode, TA = 25°C
µA
µA
µW
µW
Supply current in shutdown mode
Supply current in shutdown mode
VDD = 3.3 V, normal mode at 25°C
Power dissipated for VDD = 3.3 V, TA = 25°C
0.1
0.7 × VDD
3
0.7 × VDD
50
5
2.7
210
250
46
65
2.0
5.2
700
150
15
25
Input filtering suppresses noise spikes of less than 50 ns
Accuracy includes lifetime drift.
The equivalent 3 σ limits are ±0.33°C. This 3 σ specification is provided to enable comparison with other vendors who use these limits.
3
Based on a floating average of 10 readings.
1
2
Rev. A | Page 3 of 24
ADT7410
Data Sheet
I2C TIMING SPECIFICATIONS
TA = −55°C to +150°C, VDD = 2.7 V to 5.5 V, unless otherwise noted. All input signals are specified with rise time (tR) = fall time (tF) = 5 ns
(10% to 90% of VDD) and timed from a voltage level of 1.6 V.
Table 2.
Parameter
SERIAL INTERFACE1, 2
SCL Frequency
SCL High Pulse Width, tHIGH
SCL Low Pulse Width, tLOW
SCL, SDA Rise Time, tR
SCL, SDA Fall Time, tF
Hold Time (Start Condition), tHD;STA
Setup Time (Start Condition), tSU;STA
Data Setup Time, tSU;DAT
Min
0
0.6
1.3
2
Max
Unit
400
kHz
μs
μs
μs
μs
μs
μs
μs
μs
μs
μs
μs
0.3
0.3
0.6
0.6
0.25
0.35
0.6
0
1.3
Setup Time (Stop Condition), tSU;STO
Data Hold Time, tHD;DAT (Master)
Bus-Free Time (Between Stop and Start Condition), tBUF
1
Typ
Test Conditions/Comments
See Figure 2
After this period, the first clock is generated
Relevant for repeated start condition
VDD ≥ 3.0 V
VDD < 3.0 V
Sample tested during initial release to ensure compliance.
All input signals are specified with input rise/fall times = 3 ns, measured between the 10% and 90% points. Timing reference points at 50% for inputs and outputs.
Output load = 10 pF.
Timing Diagram
tLOW
tR
tF
tHD:STA
SCL
tHD:STA
tHD:DAT
tHIGH
tSU:STA
tSU:DAT
tSU:STO
tBUF
P
S
S
Figure 2. Serial Interface Timing Diagram
Rev. A | Page 4 of 24
P
06560-002
SDA
Data Sheet
ADT7410
ABSOLUTE MAXIMUM RATINGS
1.2
WMAX = (TJMAX − TA2)/θJA
121°C/W
56°C/W
220°C
260°C (0°C)
1.0
0.8
0.6
0.4
0.2
MAX PD = 3.4mW AT 150°C
0
20 sec to 40 sec
3°C/sec maximum
−6°C/sec maximum
8 minutes maximum
Values relate to package being used on a standard 2-layer PCB. This gives a
worst-case θJA and θJC. See Figure 3 for a plot of maximum power dissipation
vs. ambient temperature (TA).
2
TA = ambient temperature.
3
Junction-to-case resistance is applicable to components featuring a
preferential flow direction, for example, components mounted on a heat
sink. Junction-to-ambient is more useful for air-cooled, PCB-mounted
components.
1
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
TEMPERATURE (°C)
Figure 3. SOIC_N Maximum Power Dissipation vs. Temperature
ESD CAUTION
Rev. A | Page 5 of 24
06560-003
Rating
−0.3 V to +7 V
−0.3 V to VDD + 0.3 V
−0.3 V to VDD + 0.3 V
−0.3 V to VDD + 0.3 V
−0.3 V to VDD + 0.3 V
−0.3 V to VDD + 0.3 V
2.0 kV
−55°C to +150°C
−65°C to +160°C
150°C
–55
–50
–40
–30
–20
–10
0
10
20
30
40
50
60
70
80
90
100
110
120
130
140
150
Parameter
VDD to GND
SDA Voltage to GND
SCL Output Voltage to GND
A0 Input Voltage to GND
A1 Input Voltage to GND
CT and INT Output Voltage to GND
ESD Rating (Human Body Model)
Operating Temperature Range
Storage Temperature Range
Maximum Junction Temperature, TJMAX
8-Lead SOIC-N (R-8)
Power Dissipation1
Thermal Impedance3
θJA, Junction-to-Ambient (Still Air)
θJC, Junction-to-Case
IR Reflow Soldering
Peak Temperature (RoHS-Compliant
Package)
Time at Peak Temperature
Ramp-Up Rate
Ramp-Down Rate
Time from 25°C to Peak Temperature
MAXIMUM POWER DISSIPATION (W)
Table 3.
ADT7410
Data Sheet
SCL 1
SDA 2
ADT7410
A0 3
TOP VIEW
A1 4 (Not to Scale)
8
VDD
7
GND
6
CT
5
INT
06560-005
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
Figure 4. Pin Configuration
Table 4. Pin Function Descriptions
Pin No.
1
Mnemonic
SCL
2
SDA
3
4
5
A0
A1
INT
6
CT
7
8
GND
VDD
Description
I2C Serial Clock Input. The serial clock is used to clock in and clock out data to and from any register of the ADT7410.
Open-drain configuration. A pull-up resistor is required, typically 10 kΩ.
I2C Serial Data Input/Output. Serial data to and from the part is provided on this pin. Open-drain configuration. A
pull-up resistor is required, typically 10 kΩ.
I2C Serial Bus Address Selection Pin. Logic input. Connect to GND or VDD to set an I2C address.
I2C Serial Bus Address Selection Pin. Logic input. Connect to GND or VDD to set an I2C address.
Overtemperature and Undertemperature Indicator. Logic output. Power-up default setting is as an active low
comparator interrupt. Open-drain configuration. A pull-up resistor is required, typically 10 kΩ.
Critical Overtemperature Indicator. Logic output. Power-up default polarity is active low. Open-drain configuration.
A pull-up resistor is required, typically 10 kΩ.
Analog and Digital Ground.
Positive Supply Voltage (2.7 V to 5.5 V). The supply should be decoupled with a 0.1 µF ceramic capacitor to ground.
Rev. A | Page 6 of 24
Data Sheet
ADT7410
TYPICAL PERFORMANCE CHARACTERISTICS
1.0
0.30
5.5V CONTINUOUS
CONVERSION
0.25
0.6
MAX ACCURACY LIMITS
0.4
3.0V CONTINUOUS
CONVERSION
0.20
0.2
IDD (mA)
0
–0.2
0.15
0.10
–0.4
5.5V 1SPS
MAX ACCURACY LIMITS
–0.6
0.05
3.0V 1SPS
–0.8
–40
–20
0
20
40
60
80
100
120
140
160
TEMPERATURE (°C)
0
–100
06560-006
–1.0
–60
–50
0
50
100
150
200
TEMPERATURE (°C)
Figure 5. Temperature Accuracy at 3 V
06560-007
TEMPERATURE ERROR (°C)
0.8
Figure 7. Operating Supply Current vs. Temperature
1.0
30
0.8
25
SHUTDOWN IDD (µA)
0.4
0.2
0
–0.2
–0.4
20
15
10
5.5V
5.0V
5
MAX ACCURACY LIMITS
4.5V
–0.8
–1.0
–60
3.3V
3.0V
2.7V
3.6V
–40
–20
0
20
40
60
80
100
120
TEMPERATURE (°C)
140
160
0
–100
–50
0
50
100
150
TEMPERATURE (°C)
Figure 6. Temperature Accuracy at 5 V
Figure 8. Shutdown Current vs. Temperature
Rev. A | Page 7 of 24
200
06560-025
–0.6
06560-024
TEMPERATURE ERROR (°C)
MAX ACCURACY LIMITS
0.6
ADT7410
Data Sheet
160
0.30
140
IDD CONTINUOUS CONVERSION
0.25
TEMPERATURE (°C)
120
IDD (mA)
0.20
0.15
0.10
100
80
60
40
IDD 1SPS
0.05
3.0
3.5
4.0
4.5
5.0
5.5
6.0
SUPPLY VOLTAGE (V)
0
06560-008
0
2.5
0
8
7
5
4
3
2
1
3.5
4.0
4.5
5.0
5.5
SUPPLY VOLTAGE (V)
6.0
06560-009
SHUTDOWN IDD (µA)
6
3.0
10
15
20
25
30
TIME (Seconds)
Figure 9. Average Operating Supply Current vs. Supply Voltage at 25°C
0
2.5
5
Figure 10. Shutdown Current vs. Supply Voltage at 25°C
Rev. A | Page 8 of 24
Figure 11. Response to Thermal Shock
35
40
06560-011
20
Data Sheet
ADT7410
THEORY OF OPERATION
CIRCUIT INFORMATION
TEMPERATURE MEASUREMENT
The ADT7410 is a 13-bit digital temperature sensor that is extendable to 16 bits for greater resolution. An on-board temperature
sensor generates a voltage proportional to absolute temperature,
which is compared to an internal voltage reference and input to a
precision digital modulator.
In normal mode, the ADT7410 runs an automatic conversion
sequence. During this automatic conversion sequence, a conversion takes 240 ms to complete and the ADT7410 is continuously
converting. This means that as soon as one temperature conversion is completed, another temperature conversion begins. Each
temperature conversion result is stored in the temperature value
registers and is available through the I2C interface. In continuous
conversion mode, the read operation provides the most recent
converted result.
The on-board temperature sensor has excellent accuracy
and linearity over the entire rated temperature range without
needing correction or calibration by the user.
The sensor output is digitized by a sigma-delta (Σ-Δ) modulator,
also known as the charge balance type analog-to-digital converter. This type of converter utilizes time-domain oversampling
and a high accuracy comparator to deliver 16 bits of resolution
in an extremely compact circuit.
Configuration register functions consist of






Switching between 13-bit and 16-bit resolution
Switching between normal operation and full power-down
Switching between comparator and interrupt event modes
on the INT and CT pins
Setting the active polarity of the CT and INT pins
Setting the number of faults that activate CT and INT
Enabling the standard one-shot mode and 1 SPS mode
CONVERTER DETAILS
The Σ-Δ modulator consists of an input sampler, a summing
network, an integrator, a comparator, and a 1-bit DAC. This
architecture creates a negative feedback loop and minimizes the
integrator output by changing the duty cycle of the comparator
output in response to input voltage changes. The comparator
samples the output of the integrator at a much higher rate than
the input sampling frequency. This oversampling spreads the
quantization noise over a much wider band than that of the
input signal, improving overall noise performance and
increasing accuracy.
On power-up, the first conversion is a fast conversion, taking
typically 6 ms. If the temperature exceeds 147°C, the CT pin
asserts low. If the temperature exceeds 64°C, the INT pin asserts
low. Fast conversion temperature accuracy is typically within ±5°C.
The conversion clock for the part is generated internally.
No external clock is required except when reading from
and writing to the serial port.
The measured temperature value is compared with a critical
temperature limit (stored in the 16-bit TCRIT setpoint read/write
register), a high temperature limit (stored in the 16-bit THIGH setpoint read/write register), and a low temperature limit (stored
in the 16-bit TLOW setpoint read/write register). If the measured
value exceeds these limits, the INT pin is activated; and if it exceeds
the TCRIT limit, the CT pin is activated. The INT and CT pins are
programmable for polarity via the configuration register, and the
INT and CT pins are also programmable for interrupt mode via
the configuration register.
The modulated output of the comparator is encoded using
a circuit technique that results in I2C temperature data.
Σ-∆ MODULATOR
INTEGRATOR
COMPARATOR
VOLTAGE REF
AND VPTAT
1-BIT
DAC
CLOCK
GENERATOR
LPF DIGITAL
FILTER
13-BIT
TEMPERATURE
VALUE
REGISTER
06560-012
1-BIT
Figure 12. Σ-Δ Modulator
Rev. A | Page 9 of 24
ADT7410
Data Sheet
ONE-SHOT MODE
When one-shot mode is enabled, the ADT7410 immediately
completes a conversion and then goes into shutdown mode. The
one-shot mode is useful when one of the circuit design priorities is
to reduce power consumption.
writing 1 to Bit 6 and 0 to Bit 5 of the configuration register
(Register Address 0x03).
CT and INT Operation in One-Shot Mode
To enable one-shot mode, set Bits[6:5] of the configuration
register (Register Address 0x03) to 01.
See Figure 13 for more information on one-shot CT pin
operation for TCRIT overtemperature events when one of the
limits is exceeded. Note that in interrupt mode, a read from
any register resets the INT and CT pins.
After writing to the operation mode bits, wait at least 240 ms
before reading back the temperature from the temperature value
register. This delay ensures that the ADT7410 has adequate time
to power up and complete a conversion.
For the INT pin in the comparator mode, if the temperature
drops below the THIGH – THYST value or goes above the TLOW +
THYST value, a write to the one-shot bits (Bit 5 and Bit 6 of the
configuration register, Register Address 0x03) resets the INT pin.
To obtain an updated temperature conversion, reset Bits[6:5] of the
configuration register (Register Address 0x03) to 01.
For the CT pin in the comparator mode, if the temperature
drops below the TCRIT – THYST value, a write to the one-shot
bits (Bit 5 and Bit 6 of the configuration register, Register
Address 0x03) resets the CT pin. See Figure 13.
1 SPS MODE
In this mode, the part performs one measurement per second.
A conversion takes only 60 ms, and it remains in the idle state
for the remaining 940 ms period. This mode is enabled by
Note that when using one-shot mode, ensure that the refresh
rate is appropriate to the application being used.
TEMPERATURE
149°C
148°C
TCRIT
147°C
146°C
145°C
144°C
143°C
TCRIT – THYST
142°C
141°C
140°C
CT PIN
POLARITY = ACTIVE LOW
CT PIN
POLARITY = ACTIVE HIGH
TIME
WRITE TO
BIT 5 AND BIT 6 OF
CONFIGURATION
REGISTER.*
WRITE TO
BIT 5 AND BIT 6 OF
CONFIGURATION
REGISTER.*
*THERE IS A 240ms DELAY BETWEEN WRITING TO THE CONFIGURATION REGISTER TO START
A STANDARD ONE-SHOT CONVERSION AND THE CT PIN GOING ACTIVE. THIS IS DUE TO THE
CONVERSION TIME. THE DELAY IS 60ms IN THE CASE OF A 1 SPS CONVERSION.
Figure 13. One-Shot CT Pin
Rev. A | Page 10 of 24
06560-013
WRITE TO
BIT 5 AND BIT 6 OF
CONFIGURATION
REGISTER.*
Data Sheet
ADT7410
SHUTDOWN
FAULT QUEUE
The ADT7410 can be placed in shutdown mode by writing 1
to Bit 6 and 1 to Bit 5 of the configuration register (Register
Address 0x03), in which case the entire IC is shut down and
no further conversions are initiated until the ADT7410 is
taken out of shutdown mode. The ADT7410 can be taken
out of shutdown mode by writing 0 to Bit 6 and 0 to Bit 5 in
the configuration register (Register Address 0x03). The
ADT7410 typically takes 1 ms (with a 0.1 µF decoupling
capacitor) to come out of shutdown mode. The conversion
result from the last conversion prior to shutdown can still be
read from the ADT7410 even when it is in shutdown mode.
When the part is taken out of shutdown mode, the internal
clock is started and a conversion is initiated.
Bit 0 and Bit 1 of the configuration register (Register Address
0x03) are used to set up a fault queue. The queue can facilitate up
to four fault events to prevent false tripping of the INT and CT pins
when the ADT7410 is used in a noisy temperature environment.
The number of faults set in the queue must occur consecutively
to set the INT and CT outputs. For example, if the number of
faults set in the queue is four, then four consecutive temperature
conversions must occur with each result exceeding a temperature
limit in any of the limit registers before the INT and CT pins are
activated. If two consecutive temperature conversions exceed a
temperature limit and the third conversion does not, the fault
count is reset back to zero.
Rev. A | Page 11 of 24
ADT7410
Data Sheet
TEMPERATURE DATA FORMAT
TEMPERATURE CONVERSION FORMULAS
One LSB of the ADC corresponds to 0.0625°C in 13-bit mode.
The ADC can theoretically measure a temperature range of
255°C, but the ADT7410 is guaranteed to measure a low value
temperature limit of −55°C to a high value temperature limit
of +150°C. The temperature measurement result is stored in
the 16-bit temperature value register and is compared with the
high temperature limits stored in the TCRIT setpoint register and
the THIGH setpoint register. It is also compared with the low
temperature limit stored in the TLOW setpoint register.
16-Bit Temperature Data Format
Positive Temperature = ADC Code (dec)/128
Temperature data in the temperature value register, the TCRIT
setpoint register, the THIGH setpoint register, and the TLOW
setpoint register are represented by a 13-bit twos complement
word. The MSB is the temperature sign bit. The three LSBs, Bit 0
to Bit 2, on power-up, are not part of the temperature conversion result and are flag bits for TCRIT, THIGH, and TLOW. Table 5
shows the 13-bit temperature data format without Bit 0 to Bit 2.
The number of bits in the temperature data-word can be extended
to 16 bits, twos complement, by setting Bit 7 to 1 in the configuration register (Register Address 0x03). When using a 16-bit
temperature data value, Bit 0 to Bit 2 are not used as flag bits
and are, instead, the LSB bits of the temperature value. The
power-on default setting has a 13-bit temperature data value.
Reading back the temperature from the temperature value register
requires a 2-byte read. Designers that use a 9-bit temperature
data format can still use the ADT7410 by ignoring the last four
LSBs of the 13-bit temperature value. These four LSBs are Bit 6
to Bit 3 in Table 5.
Table 5. 13-Bit Temperature Data Format
Temperature
−55°C
−50°C
−25°C
−0.0625°C
0°C
+0.0625°C
+25°C
+50°C
+125°C
+150°C
Digital Output
(Binary) Bits[15:3]
1 1100 1001 0000
1 1100 1110 0000
1 1110 0111 0000
1 1111 1111 1111
0 0000 0000 0000
0 0000 0000 0001
0 0001 1001 0000
0 0011 0010 0000
0 0111 1101 0000
0 1001 0110 0000
Digital Output (Hex)
0x1C90
0x1CE0
0x1E70
0x1FFF
0x000
0x001
0x190
0x320
0x7D0
0x960
Negative Temperature = (ADC Code (dec) – 65,536)/128
where ADC Code uses all 16 bits of the data byte, including the
sign bit.
Negative Temperature = (ADC Code (dec) – 32,768)/128
where Bit 15 (sign bit) is removed from the ADC code.
13-Bit Temperature Data Format
Positive Temperature = ADC Code (dec)/16
Negative Temperature = (ADC Code (dec) − 8192)/16
where ADC Code uses the first 13 MSBs of the data byte,
including the sign bit.
Negative Temperature = (ADC Code (dec) – 4096)/16
where Bit 15 (sign bit) is removed from the ADC code.
10-Bit Temperature Data Format
Positive Temperature = ADC Code (dec)/2
Negative Temperature = (ADC Code (dec) − 1024)/2
where ADC Code uses all 10 bits of the data byte, including the
sign bit.
Negative Temperature = (ADC Code (dec) − 512)/2
where Bit 9 (sign bit) is removed from the ADC code.
9-Bit Temperature Data Format
Positive Temperature = ADC Code (dec)
Negative Temperature = ADC Code (dec) − 512
where ADC Code uses all nine bits of the data byte, including
the sign bit.
Negative Temperature = ADC Code (dec) − 256
where Bit 8 (sign bit) is removed from the ADC code.
Rev. A | Page 12 of 24
Data Sheet
ADT7410
REGISTERS
The ADT7410 contains 14 registers:
ADDRESS POINTER REGISTER
•
•
•
•
•
•
This register is always the first register written to during a write
to the ADT7410. It should be set to the address of the register
to which the write or read transaction is intended. Table 7
shows the register address of each register on the ADT7410.
The default value of the address pointer register is 0x00.
Nine temperature registers
A status register
An ID register
A configuration register
An address pointer register
A software reset
Table 7. Address Pointer Register
All registers are eight bits wide. The temperature value registers,
the status register, and the ID register are read-only. The software
reset is a write-only register. On power-up, the address pointer
register is loaded with 0x00 and points to the temperature value
register MSB.
Table 6. ADT7410 Registers
Register
Address
0x00
0x01
0x02
0x03
0x04
0x05
0x06
0x07
0x08
0x09
0x0A
0x0B
0x2F
Description
Temperature value most significant byte
Temperature value least significant byte
Status
Configuration
THIGH setpoint most significant byte
THIGH setpoint least significant byte
TLOW setpoint most significant byte
TLOW setpoint least significant byte
TCRIT setpoint most significant byte
TCRIT setpoint least significant byte
THYST setpoint
ID
Software reset
Power-On
Default
0x00
0x00
0x00
0x00
0x20 (64°C)
0x00 (64°C)
0x05 (10°C)
0x00 (10°C)
0x49 (147°C)
0x80 (147°C)
0x05 (5°C)
0xCX
0xXX
P7
ADD7
P6
ADD6
P5
ADD5
P4
ADD4
P3
ADD3
P2
ADD2
P1
ADD1
TEMPERATURE VALUE REGISTERS
The temperature value most significant byte (MSB) and temperature value least significant byte (LSB) registers store the
temperature measured by the internal temperature sensor.
The temperature is stored in twos complement format with
the MSB being the temperature sign bit. When reading from
these registers, the eight MSBs (Bit 7 to Bit 15) are read first
from Register Address 0x00 and then the eight LSBs (Bit 0 to
Bit 7) are read from Register Address 0x01. Only the temperature value most significant byte (Register Address 0x00) needs to
be loaded into the address pointer register as the address pointer
auto-increments to the Temperature value least significant byte
address (Register Address 0x01).
Bit 0 to Bit 2 are event alarm flags for TCRIT, THIGH, and TLOW. When
the ADC is configured to convert the temperature to a 16-bit
digital value then Bit 0 to Bit 2 are no longer used as flag bits
and are instead used as the LSB bits for the extended digital value.
Table 8. Temperature Value MSB Register (Register Address 0x00)
Bit
[14:8]
15
Default Value
0000000
0
Type
R
R
Name
Temp
Sign
Description
Temperature value in twos complement format
Sign bit, indicates if the temperature value is negative or positive
Table 9. Temperature Value LSB Register (Register Address 0x01)
Bit
0
Default
Value
0
Type
R
Name
TLOW flag/LSB0
1
0
R
THIGH flag/LSB1
2
0
R
TCRIT flag/LSB2
[7:3]
00000
R
Temp
P0
ADD0
Description
Flags a TLOW event if the configuration register, Register Address 0x03[7] = 0 (13-bit
resolution). When the temperature value is below TLOW, this bit it set to 1.
Contains the Least Significant Bit 0 of the 15-bit temperature value if the configuration
register, Register Address 0x03[7] = 1 (16-bit resolution).
Flags a THIGH event if the configuration register, Register Address 0x03[7] = 0 (13-bit
resolution). When the temperature value is above THIGH, this bit it set to 1.
Contains the Least Significant Bit 1 of the 15-bit temperature value if the configuration
register, Register Address 0x03[7] = 1 (16-bit resolution).
Flags a TCRIT event if the configuration register, Register Address 0x03[7] = 0 (13-bit
resolution). When the temperature value exceeds TCRIT, this bit it set to 1.
Contains the Least Significant Bit 2 of the 15-bit temperature value if the configuration
register, Register Address 0x03[7] = 1 (16-bit resolution).
Temperature value in twos complement format.
Rev. A | Page 13 of 24
ADT7410
Data Sheet
STATUS REGISTER
This 8-bit read-only register reflects the status of the overtemperature and undertemperature interrupts that can cause the CT and
INT pins to go active. It also reflects the status of a temperature
conversion operation. The interrupt flags in this register are
reset by a read operation to the status register and/or when
the temperature value returns within the temperature limits,
including hysteresis. The RDY bit is reset after a read from the
temperature value register. In one-shot and 1 SPS modes,
the RDY bit is reset after a write to the one-shot bits.
CONFIGURATION REGISTER
This 8-bit read/write register stores various configuration modes
for the ADT7410, including shutdown, overtemperature and
undertemperature interrupts, one-shot, continuous conversion,
interrupt pins polarity, and overtemperature fault queues.
Table 10. Status Register (Register Address 0x02)
Bit
[3:0]
4
Default
Value
0000
0
Type
R
R
Name
Unused
TLOW
5
0
R
THIGH
6
0
R
TCRIT
7
1
R
RDY
Description
Reads back 0.
This bit is set to 1 when the temperature goes below the TLOW temperature limit. The bit clears to 0
when the status register is read and/or when the temperature measured goes back above the limit
set in the setpoint TLOW + THYST registers.
This bit is set to 1 when the temperature goes above the THIGH temperature limit. The bit clears to 0
when the status register is read and/or when the temperature measured goes back below the limit
set in the setpoint THIGH − THYST registers.
This bit is set to 1 when the temperature goes above the TCRIT temperature limit. This bit clears to 0
when the status register is read and/or when the temperature measured goes back below the limit
set in the setpoint TCRIT − THYST registers.
This bit goes low when the temperature conversion result is written into the temperature value
register. It is reset to 1 when the temperature value register is read. In one-shot and 1 SPS modes,
this bit is reset after a write to the one-shot bits.
Table 11. Configuration Register (Register Address 0x03)
Bit
[1:0]
Default
Value
00
Type
R/W
Name
Fault queue
2
0
R/W
CT pin polarity
3
0
R/W
INT pin polarity
4
0
R/W
INT/CT mode
[6:5]
00
R/W
Operation mode
7
0
R/W
Resolution
Description
These two bits set the number of undertemperature/overtemperature faults that can occur before
setting the INT and CT pins. This helps to avoid false triggering due to temperature noise.
00 = 1 fault (default).
01 = 2 faults.
10 = 3 faults.
11 = 4 faults.
This bit selects the output polarity of the CT pin.
0 = active low.
1 = active high.
This bit selects the output polarity of the INT pin.
0 = active low.
1 = active high.
This bit selects between comparator mode and interrupt mode.
0 = interrupt mode
1 = comparator mode
These two bits set the operational mode for the ADT7410.
00 = continuous conversion (default). When one conversion is finished, the ADT7410 starts
another.
01 = one shot. Conversion time is typically 240 ms.
10 = 1 SPS mode. Conversion time is typically 60 ms. This operational mode reduces the average
current consumption.
11 = shutdown. All circuitry except interface circuitry is powered down.
This bit sets up the resolution of the ADC when converting.
0 = 13-bit resolution. Sign bit + 12 bits gives a temperature resolution of 0.0625°C.
1 = 16-bit resolution. Sign bit + 15 bits gives a temperature resolution of 0.0078°C.
Rev. A | Page 14 of 24
Data Sheet
ADT7410
THIGH SETPOINT REGISTERS
The THIGH setpoint MSB and THIGH setpoint LSB registers store
the overtemperature limit value. An overtemperature event
occurs when the temperature value stored in the temperature
value register exceeds the value stored in this register. The INT
pin is activated if an overtemperature event occurs. The temperature is stored in twos complement format with the MSB being
the temperature sign bit.
When reading from this register, the eight MSBs (Bit 15 to Bit 8)
are read first from Register Address 0x04 and then the eight
LSBs (Bit 7 to Bit 0) are read from Register Address 0x05. Only
Register Address 0x04 (THIGH setpoint MSB) needs to be loaded
into the address pointer register as the address pointer autoincrements to Register Address 0x05 (THIGH setpoint LSB).
The default setting for the THIGH setpoint is 64°C.
TLOW SETPOINT REGISTERS
The TLOW setpoint MSB and TLOW setpoint LSB registers store
the undertemperature limit value. An undertemperature event
occurs when the temperature value stored in the temperature
value register is less than the value stored in this register. The
INT pin is activated if an undertemperature event occurs. The
temperature is stored in twos complement format with the MSB
being the temperature sign bit.
When reading from this register, the eight MSBs (Bit 15 to Bit
8) are read first from Register Address 0x06 and then the eight
LSBs (Bit 7 to Bit 0) are read from Register Address 0x07. Only
the Register Address 0x06 (TLOW setpoint MSB) needs to be
loaded into the address pointer register as the address pointer
auto-increments to Register Address 0x07 (TLOW setpoint LSB).
The default setting for the TLOW setpoint is 10°C.
TCRIT SETPOINT REGISTERS
The TCRIT setpoint MSB and TCRIT setpoint LSB registers store
the critical overtemperature limit value. A critical overtemperature event occurs when the temperature value stored in the
temperature value register exceeds the value stored in this
register. The CT pin is activated if a critical overtemperature
event occurs. The temperature is stored in twos complement
format with the MSB being the temperature sign bit.
When reading from this register, the eight MSBs (Bit 15 to Bit 8)
are read first from Register Address 0x08 and then the eight
LSBs (Bit 7 to Bit 0) are read from Register Address 0x09.
Only the Register Address 0x08 (TCRIT setpoint MSB) needs to
be loaded into the address pointer register as the address pointer
auto-increments to Register Address 0x09 (TCRIT setpoint LSB).
The default setting for the TCRIT limit is 147°C.
Table 12. THIGH Setpoint MSB Register (Register Address 0x04)
Bit
Default Value
Type
Name
Description
[15:8]
0x20
R/W
THIGH MSB
MSBs of the overtemperature limit, stored in twos complement format.
Table 13. THIGH Setpoint LSB Register (Register Address 0x05)
Bit
Default Value
Type
Name
Description
[7:0]
0x00
R/W
THIGH LSB
LSBs of the overtemperature limit, stored in twos complement format.
Table 14. TLOW Setpoint MSB Register (Register Address 0x06)
Bit
Default Value
Type
Name
Description
[15:8]
0x05
R/W
TLOW MSB
MSBs of the undertemperature limit, stored in twos complement format.
Table 15. TLOW Setpoint LSB Register (Register Address 0x07)
Bit
Default Value
Type
Name
Description
[7:0]
0x00
R/W
TLOW LSB
LSBs of the undertemperature limit, stored in twos complement format.
Table 16. TCRIT Setpoint MSB Register (Register Address 0x08)
Bit
Default Value
Type
Name
Description
[15:8]
0x49
R/W
TCRIT MSB
MSBs of the critical overtemperature limit, stored in twos complement format.
Table 17. TCRIT Setpoint LSB Register (Register Address 0x09)
Bit
Default Value
Type
Name
Description
[7:0]
0x80
R/W
TCRIT LSB
LSBs of the critical overtemperature limit, stored in twos complement format.
Rev. A | Page 15 of 24
ADT7410
Data Sheet
THYST SETPOINT REGISTER
ID REGISTER
This 8-bit read/write register stores the temperature hysteresis
value for the THIGH, TLOW, and TCRIT temperature limits. The
temperature hysteresis value is stored in straight binary format
using four LSBs. Increments are possible in steps of 1°C from
0°C to 15°C. The value in this register is subtracted from the
THIGH and TCRIT values and added to the TLOW value to implement hysteresis.
This 8-bit read-only register stores the manufacturer ID in Bit 3
to Bit 7 and the silicon revision in Bit 0 to Bit 2.
Table 18. THYST Setpoint Register (Register Address 0x0A)
Bit
Default Value
Type
Name
Description
[3:0]
0101
R/W
THYST
Hysteresis value, from 0°C to 15°C. Stored in straight binary format. The default setting is 5°C.
[7:4]
0000
R/W
N/A
Not used.
Table 19. ID Register (Register Address 0x0B)
Bit
[2:0]
[7:3]
Default Value
XXX
11001
Type
R
R
Name
Revision ID
Manufacture ID
Description
Contains the silicon revision identification number
Contains the manufacturer identification number
Rev. A | Page 16 of 24
Data Sheet
ADT7410
SERIAL INTERFACE
PULL-UP
VDD
VDD
VDD
10kΩ
10kΩ
ADT7410
CT
INT
TO INTERRUPT PIN
ON MICROCONTROLLER
A0
A1
PULL-UP
VDD
10kΩ
10kΩ
0.1µF
SCL
SDA
06560-014
PULL-UP
VDD
GND
Figure 14. Typical I2C Interface Connection
Control of the ADT7410 is carried out via the I2C-compatible
serial interface. The ADT7410 is connected to this bus as a slave
and is under the control of a master device.
2.
Figure 14 shows a typical I2C interface connection.
SERIAL BUS ADDRESS
Like all I2C-compatible devices, the ADT7410 has a 7-bit serial
address. The five MSBs of this address for the ADT7410 are set
to 10010. Pin A1 and Pin A0 set the two LSBs. These pins can
be configured two ways, low and high, to give four different
address options. Table 20 shows the different bus address options
available. The recommended pull-up resistor value on the SDA
and SCL lines is 10 kΩ.
Table 20. I2C Bus Address Options
Binary
A6
1
1
1
1
A5
0
0
0
0
A4
0
0
0
0
A3
1
1
1
1
A2
0
0
0
0
3.
4.
A1
0
0
1
1
A0
0
1
0
1
Hex
0x48
0x49
0x4A
0x4B
The serial bus protocol operates as follows:
1.
The master initiates data transfer by establishing a start
condition, defined as a high-to-low transition on the serial
data line, SDA, while the serial clock line, SCL, remains
high. This indicates that an address/data stream is going
to follow. All slave peripherals connected to the serial bus
respond to the start condition and shift in the next eight
bits, consisting of a 7-bit address (MSB first) plus a read/
write (R/W) bit. The R/W bit determines whether data is
written to, or read from, the slave device.
The peripheral with the address corresponding to the
transmitted address responds by pulling the data line low
during the low period before the ninth clock pulse, known
as the acknowledge bit. All other devices on the bus then
remain idle while the selected device waits for data to be
read from or written to it. If the R/W bit is a 0, the master
writes to the slave device. If the R/W bit is a 1, the master
reads from the slave device.
Data is sent over the serial bus in sequences of nine clock
pulses, eight bits of data followed by an acknowledge bit
from the receiver of data. Transitions on the data line must
occur during the low period of the clock signal and remain
stable during the high period as a low-to-high transition when
the clock is high, which can be interpreted as a stop signal.
When all data bytes have been read or written, stop conditions are established. In write mode, the master pulls the
data line high during the 10th clock pulse to assert a stop
condition. In read mode, the master device pulls the data
line high during the low period before the ninth clock
pulse. This is known as a no acknowledge. The master
takes the data line low during the low period before the
10th clock pulse, then high during the 10th clock pulse to
assert a stop condition.
It is not possible to mix read and write in one operation because
the type of operation is determined at the beginning and cannot
subsequently be changed without starting a new operation.
Rev. A | Page 17 of 24
ADT7410
Data Sheet
the same write transaction. Writing two bytes of data to these
registers requires the serial bus address, the data register address
of the MSB register written to the address pointer register,
followed by the two data bytes written to the selected data
register. This is shown in Figure 16.
WRITING DATA
It is possible to write either a single byte of data or two bytes to
the ADT7410, depending on which registers are to be written.
Writing a single byte of data requires the serial bus address, the
data register address written to the address pointer register,
followed by the data byte written to the selected data register.
This is shown in Figure 15.
If more than the required number of data bytes is written to a
register, the register ignores these extra data bytes. To write to
a different register, a start or repeated start is required.
For the THIGH setpoint, TLOW setpoint, and TCRIT setpoint registers,
it is possible to write to both the MSB and the LSB registers in
1
9
1
9
SCL
1
SDA
0
0
1
0
A1
A0
P7
R/W
START BY
MASTER
P6
P5
P4
P3
P2
P1
P0
ACK. BY
ADT7410
ACK. BY
ADT7410
FRAME 2
ADDRESS POINTER REGISTER BYTE
FRAME 1
SERIAL BUS ADDRESS BYTE
1
9
SCL (CONTINUED)
D7
D6
D5
D4
D3
D2
D1
D0
STOP BY
MASTER
ACK. BY
ADT7410
FRAME 3
DATA BYTE
06560-016
SDA (CONTINUED)
Figure 15. Writing to a Register Followed by a Single Byte of Data
1
9
1
9
SCL
SDA
1
0
0
1
0
A1
A0
P7
R/W
START BY
MASTER
P6
P5
P4
P3
P2
P1
P0
ACK. BY
ADT7410
ACK. BY
ADT7410
FRAME 1
SERIAL BUS ADDRESS BYTE
FRAME 2
ADDRESS POINTER REGISTER BYTE
1
9
1
9
SCL (CONTINUED)
D15
D14
D13
D12
D11
D10
D9
D8
D7
D6
D5
D4
D3
D2
ACK. BY
ADT7410
FRAME 3
DATA BYTE
Rev. A | Page 18 of 24
D0
ACK. BY
ADT7410
FRAME 4
DATA BYTE
Figure 16. Writing to a Register Followed by Two Bytes of Data
D1
STOP BY
MASTER
06560-017
SDA (CONTINUED)
Data Sheet
ADT7410
READING DATA
RESET
Reading data from the ADT7410 is done in a single data byte
operation for the configuration register, the status register,
the THYST register, and the ID register. A two data byte read
operation is needed for the temperature value register, THIGH
setpoint register, TLOW setpoint register, and the TCRIT setpoint
register. Reading back the contents of an 8-bit register similar
to the configuration register is shown in Figure 17. Reading
back the contents of the temperature value register is shown
in Figure 18.
To reset the ADT7410 without having to reset the entire I2C bus,
an explicit reset command is provided. This uses a particular
address pointer word as a command word to reset the part and
upload all default settings. The ADT7410 does not respond to
the I2C bus commands (do not acknowledge) during the default
values upload for approximately 200 µs.
Reading back from any register first requires a single-byte write
operation to the address pointer register to set up the address of
the register that is going to be read from. In the case of reading
back from the 2-byte registers, the address pointer automatically
increments from the MSB register address to the LSB register
address.
When a master issues a slave address consisting of seven 0s with
the eighth bit (R/W bit) set to 0, this is known as the general call
address. The general call address is for addressing every device
connected to the I2C bus. The ADT7410 acknowledges this address
and reads in the following data byte.
The reset command address word is 0x2F.
GENERAL CALL
If the second byte is 0x06, the ADT7410 is reset, completely
uploading all default values. The ADT7410 does not respond
to the I2C bus commands (do not acknowledge) while the
default values upload for approximately 200 µs.
To read from another register, execute another write to the
address pointer register to set up the relevant register address.
Thus, block reads are not possible, that is, there is no I2C address
pointer auto-increment except when reading back from a 16-bit
register. If the address pointer register has previously been set
up with the address of the register that is going to receive a read
command, there is no need to repeat a write operation to set up
the register address again.
1
The ADT7410 does not acknowledge any other general call
commands.
9
1
9
SCL
SDA
1
0
0
1
0
A1
A0
START BY
MASTER
R/W
P7
P6
P5
P4
P3
P2
P1
P0
ACK. BY
ADT7410
ACK. BY
ADT7410
FRAME 1
SERIAL BUS ADDRESS
BYTE
FRAME 2
ADDRESS POINTER REGISTER BYTE
1
9
1
9
SCL
1
0
0
1
0
A2
FRAME 3
SERIAL BUS ADDRESS
BYTE
A0
R/W
D7
D6
ACK. BY
ADT7410
D5
D4
D3
D1
FRAME 4
DATA BYTE FROM CONFIGURATION
REGISTER
Figure 17. Reading Back Data from the Configuration Register
Rev. A | Page 19 of 24
D2
D0
NO ACK. BY STOP BY
MASTER MASTER
06560-018
SDA
REPEAT START
BY MASTER
ADT7410
Data Sheet
9
1
9
1
SCL
SDA
1
0
0
0
1
A1
A0
ADT7410 DEVICE ADDRESS
START
ACK. BY
ADT7410
1
SR
A7
R/W
A6
A1
A0
REGISTER ADDRESS[A7:A0]
9
ACK. BY
ADT7410
1
9
SCL
1
REPEAT
START
0
A1
A0
ADT7410 DEVICE ADDRESS
R/W
ACK. BY
ADT7410
D7
D6
D1
TEMPERATURE REGISTER
MSB DATA
D0
ACK. BY
MASTER
D7
D6
D1
TEMPERATURE REGISTER
LSB DATA
D0
NO
ACK. BY
MASTER
NOTES
1. A START CONDITION AT THE BEGINNING IS DEFINED AS A HIGH-TO-LOW TRANSITION ON SDA WHILE SCLK REMAINS HIGH.
2. A STOP CONDITION AT THE END IS DEFINED AS A LOW-TO-HIGH TRANSITION ON SDA WHILE SCLK REMAINS HIGH.
3. THE MASTER GENERATES THE NO ACKNOWLEDGE AT THE END OF THE READBACK TO SIGNAL THAT IT DOES NOT WANT ADDITIONAL DATA.
4. TEMPERATURE REGISTER MSB DATA AND TEMPERATURE REGISTER LSB DATA ARE ALWAYS SEPARATED BY A LOW ACK BIT.
5. THE R/W BIT IS SET TO A1 TO INDICATE A READBACK OPERATION.
Figure 18. Reading Back Data from the Temperature Value Register
Rev. A | Page 20 of 24
06560-023
SDA
Data Sheet
ADT7410
INT AND CT OUTPUTS
Comparator Mode
The INT and CT pins are open-drain outputs, and both pins
require a 10 kΩ pull-up resistor to VDD.
In comparator mode, the INT pin returns to its inactive status
when the temperature drops below the THIGH − THYST limit or
rises above the TLOW + THYST limit.
UNDERTEMPERATURE AND OVERTEMPERATURE
DETECTION
Putting the ADT7410 into shutdown mode does not reset the
INT state in comparator mode.
The INT and CT pins have two undertemperature/overtemperature
modes: comparator mode and interrupt mode. The interrupt
mode is the default power-up overtemperature mode. The INT
output pin becomes active when the temperature is greater than
the temperature stored in the THIGH setpoint register or less than
the temperature stored in the TLOW setpoint register. How this pin
reacts after this event depends on the overtemperature mode
selected.
Interrupt Mode
In interrupt mode, the INT pin goes inactive when any ADT7410
register is read. Once the INT pin is reset, it goes active again
only when the temperature is greater than the temperature stored
in the THIGH setpoint register or less than the temperature stored
in the TLOW setpoint register.
Figure 19 illustrates the comparator and interrupt modes for
events exceeding the THIGH limit with both pin polarity settings.
Figure 20 illustrates the comparator and interrupt modes for
events exceeding the TLOW limit with both pin polarity settings.
Placing the ADT7410 into shutdown mode resets the INT pin
in the interrupt mode.
TEMPERATURE
82°C
81°C
THIGH
80°C
79°C
78°C
77°C
76°C
THIGH – THYST
75°C
74°C
73°C
INT PIN
(COMPARATOR MODE)
POLARITY = ACTIVE LOW
INT PIN
(INTERRUPT MODE)
POLARITY = ACTIVE LOW
INT PIN
(COMPARATOR MODE)
POLARITY = ACTIVE HIGH
TIME
READ
READ
READ
06560-020
INT PIN
(INTERRUPT MODE)
POLARITY = ACTIVE HIGH
Figure 19. INT Output Temperature Response Diagram for THIGH Overtemperature Events
Rev. A | Page 21 of 24
ADT7410
Data Sheet
TEMPERATURE
–13°C
–14°C
TLOW + THYST
–15°C
–16°C
–17°C
–18°C
–19°C
TLOW
–20°C
–21°C
–22°C
INT PIN
(COMPARATOR MODE)
POLARITY = ACTIVE LOW
INT PIN
(INTERRUPT MODE)
POLARITY = ACTIVE LOW
INT PIN
(COMPARATOR MODE)
POLARITY = ACTIVE HIGH
TIME
READ
READ
READ
06560-021
INT PIN
(INTERRUPT MODE)
POLARITY = ACTIVE HIGH
Figure 20. INT Output Temperature Response Diagram for TLOW Undertemperature Events
Rev. A | Page 22 of 24
Data Sheet
ADT7410
APPLICATIONS INFORMATION
THERMAL RESPONSE TIME
TEMPERATURE MONITORING
The time required for a temperature sensor to settle to a specified
accuracy is a function of the thermal mass of the sensor and the
thermal conductivity between the sensor and the object being
sensed. Thermal mass is often considered equivalent to capacitance. Thermal conductivity is commonly specified using the
symbol, Q, and can be thought of as thermal resistance. It is
commonly specified in units of degrees per watt of power
transferred across the thermal joint. The time required for
the part to settle to the desired accuracy is dependent on the
thermal contact established in a particular application and the
equivalent power of the heat source. In most applications, it is
best to determine the settling time empirically.
The ADT7410 is ideal for monitoring the thermal environment
within electronic equipment. For example, the surface-mounted
package accurately reflects the exact thermal conditions that
affect nearby integrated circuits.
SUPPLY DECOUPLING
Decouple the ADT7410 with a 0.1 µF ceramic capacitor
between VDD and GND. This is particularly important when
the ADT7410 is mounted remotely from the power supply.
Precision analog products, such as the ADT7410, require a
well-filtered power source. Because the ADT7410 operates
from a single supply, it might seem convenient to tap into the
digital logic power supply. Unfortunately, the logic supply is
often a switch-mode design, which generates noise in the
20 kHz to 1 MHz range. In addition, fast logic gates can
generate glitches hundreds of millivolts in amplitude due
to wiring resistance and inductance.
The ADT7410 measures and converts the temperature at the
surface of its own semiconductor chip. When the ADT7410 is
used to measure the temperature of a nearby heat source, the
thermal impedance between the heat source and the ADT7410
must be considered.
When the thermal impedance is determined, the temperature
of the heat source can be inferred from the ADT7410 output.
As much as 60% of the heat transferred from the heat source to
the thermal sensor on the ADT7410 die is discharged via the
copper tracks, the package pins, and the bond pads. Of the
pins on the ADT7410, the GND pin transfers most of the heat.
Therefore, to measure the temperature of a heat source, it is
recommended that the thermal resistance between the GND pin
of the ADT7410 and the GND of the heat source be reduced as
much as possible.
If possible, the ADT7410 should be powered directly from the
system power supply. This arrangement, shown in Figure 21,
isolates the analog section from the logic switching transients.
Even if a separate power supply trace is not available, generous
supply bypassing reduces supply-line induced errors. Local
supply bypassing consisting of a 0.1 µF ceramic capacitor
is critical for the temperature accuracy specifications to be
achieved. This decoupling capacitor must be placed as close
as possible to the VDD pin of the ADT7410.
0.1µF
ADT7410
POWER
SUPPLY
06560-022
TTL/CMOS
LOGIC
CIRCUITS
Figure 21. Use of Separate Traces to Reduce Power Supply Noise
Rev. A | Page 23 of 24
ADT7410
Data Sheet
OUTLINE DIMENSIONS
5.00 (0.1968)
4.80 (0.1890)
1
5
6.20 (0.2441)
5.80 (0.2284)
4
1.27 (0.0500)
BSC
0.25 (0.0098)
0.10 (0.0040)
COPLANARITY
0.10
SEATING
PLANE
1.75 (0.0688)
1.35 (0.0532)
0.51 (0.0201)
0.31 (0.0122)
0.50 (0.0196)
0.25 (0.0099)
45°
8°
0°
0.25 (0.0098)
0.17 (0.0067)
1.27 (0.0500)
0.40 (0.0157)
COMPLIANT TO JEDEC STANDARDS MS-012-AA
CONTROLLING DIMENSIONS ARE IN MILLIMETERS; INCH DIMENSIONS
(IN PARENTHESES) ARE ROUNDED-OFF MILLIMETER EQUIVALENTS FOR
REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN.
012407-A
8
4.00 (0.1574)
3.80 (0.1497)
Figure 22. 8-Lead Standard Small Outline Package [SOIC_N]
Narrow Body
(R-8)
Dimensions shown in millimeters and (inches)
ORDERING GUIDE
Model 1
ADT7410TRZ
ADT7410TRZ-REEL
ADT7410TRZ-REEL7
EVAL-ADT7X10EBZ
1
2
Temperature Range
–55°C to +150°C
–55°C to +150°C
–55°C to +150°C
Temperature Accuracy 2
±0.5°C
±0.5°C
±0.5°C
Package Description
8-Lead SOIC_N
8-Lead SOIC_N
8-Lead SOIC_N
Evaluation Board
Package Option
R-8
R-8
R-8
Z = RoHS Compliant Part.
Maximum accuracy over the −40°C to +105°C temperature range.
Purchase of licensed I2C components of Analog Devices or one of its sublicensed Associated Companies conveys a license for the purchaser under the Philips I2C Patent
Rights to use these components in an I2C system, provided that the system conforms to the I2C Standard Specification as defined by Philips.
©2009–2011 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D06560-0-12/11(A)
Rev. A | Page 24 of 24