TLV320DAC3100 Test for Detection of Open

Application Report
SLAA540B – June 2012 – Revised June 2013
TLV320DAC3100 Test for Detection of Open Loads
Wen-Shin Wang............................................................................................. MSA Catalog Applications
ABSTRACT
An open-load detection test can be implemented using headset-detection test of the TLV320DAC3100.
This application note provides a summary of the headset-detection test with the TLV320DAC3100 EVM
and how to use the headset-detection test to detect an open load.
1
Test for Detection of Headsets
Headset detection is normally used to determine if a headset has been inserted into the EVM. It can also
determine the type of headset, either with or without a microphone. This detection is accomplished by
observing the voltage on the MICDET input. See Figure 1 for schematic representation and Table 1 for
threshold voltages.
Table 1. Voltage Threshold for Detection of Headsets
REGISTER 67
BITS
REGISTER VALUE
DESCRIPTION
VOLTAGE THRESHOLD
D6-D5
(1)
(2)
00
0x80
No headset detected
MICDET > approx. 0.91 × MICBIAS (1) (2)
01
0xA0
Headset without microphone detected
MICDET < approx. 0.1 × MICBIAS
11
0xE0
Headset with microphone detected
Approx. 0.1 × MICBIAS < MICDET <
approx. 0.9 × MICBIAS
MICBIAS by default is powered to AVDD and can also be powered to 2.5 V, 2 V, or powered down.
If MICBIAS is powered down, the voltage threshold is based on DVDD.
MICBIAS
100 kΩ
R1
100 kΩ
220 µF
R2
10 kΩ
VOL/MICDET
4.7 µF
150 µH
SPKP
Class D
driver
8- or 4-Ω
speaker
SPKM
150 µH
220 µF
4.7 µF
100 kΩ
R3
DAC3100
Figure 1. Test Layout for Detection of Open Loads
SLAA540B – June 2012 – Revised June 2013
Submit Documentation Feedback
TLV320DAC3100 Test for Detection of Open Loads
Copyright © 2012–2013, Texas Instruments Incorporated
1
Test for Detection of Open Loads
www.ti.com
For the open-load test, the feature for headset detection makes a voltage measurement that can
determine the continuity of the speaker circuit. The voltage on the MICDET pin is set by the divider
consisting of R1, R2, R3, and the resistance of the speaker (see Figure 1). During an open circuit, the
resistance of the speaker circuit is near infinity; therefore, the MICDET voltage is simply pulled to
MICBIAS. During normal conditions, the resistance of the speaker circuit is near zero compared to the
resistance of R1, R2, and R3, and thus the MICDET voltage is calculated according to formula. See
Equation 1 for the calculation of MICDET.
æ R 2 + R3 ö
VMICDET = ç
÷ VMICBIAS
è R1 + R2 + R3 ø
æ
ö
100 kW + 100 kW VMICDET = ç
÷ 3.3 V
è 100 kW + 100 kW + 100 kW ø
æ2ö
VMICDET = ç ÷ 3.3 V
è3ø
VMICDET = 2.2 V
(1)
The detection feature must be specifically activated, because it is not enabled by default. To enable
headset detection, see Section 5.5.5 in the data manual (SLAS671).
2
Test for Detection of Open Loads
The layout of the test for detection of open loads is as seen in Figure 1.
When a load is detected, MICDET is pulled below the 0.91 × MICBIAS threshold (≈ 2.2 V in this case),
which allows for a headset to be detected. When the load is disconnected, MICDET is pulled to MICBIAS,
and no headset is detected. See Figure 2 for an example. Figure 3 shows the register values provided
when using the EVM GUI Command Buffer prompt.
MICBIAS
MICBIAS
100 kΩ
10 kΩ
VOL/MICDET
100 kΩ
VOL/MICDET
4.7 µF
4.7 µF
100 kΩ
220 µF
150 µH
SPKP
Class D
driver
150 µH
100 kΩ
220 µF
150 µH
SPKP
8- or 4-Ω
speaker
SPKM
10 kΩ
Class D
driver
8- or 4-Ω
speaker
SPKM
220 µF
150 µH
4.7 µF
220 µF
4.7 µF
100 kΩ
DAC3100
100 kΩ
DAC3100
Figure 2. Voltage Flow of MICDET With and Without an Open Load
2
TLV320DAC3100 Test for Detection of Open Loads
Copyright © 2012–2013, Texas Instruments Incorporated
SLAA540B – June 2012 – Revised June 2013
Submit Documentation Feedback
Test for Detection of Open Loads
www.ti.com
Figure 3. Register Values From the Command Prompt
The resistors between MICBIAS and MICDET to ground must be high, such as 100 kΩ, to reduce losses,
limit the current, and ensure that the output is not being driven back into the input. The resistor from
MICBIAS to ground can be any value, such as 10 kΩ, to complete the current path to ground.
The 220-µF capacitors are necessary to minimize dc bias of the detection circuit. These capacitors must
be large in order to minimize any contribution to the series impedance of the speaker circuit.
The inductors, and specifically the 4.7-µF capacitors, act as output filters. Because the TLV320 family
uses BD modulation, a capacitor (CBTL) is not needed between SPKP and SPKM as it usually is for AD
modulation.
In Figure 1, the output filter (second-order Butterworth low-pass) is set to a cutoff frequency of 6 kHz with
an 8-Ω load. See Equation 2 and Equation 3 for calculating the C and L values.
1
C=
w0 ´ R L ´ 2 C=
1
æ RL
2pf ´ çç
è 2
C=
*
ö
÷÷ ´ 2
ø
1
2p(6 kHz) ´ 4 W ´ 2 C = 4.689 μF » 4.7 μF
(2)
* RL becomes RL / 2 to account for analysis of the differential mode. See Figure 4 for the equivalent circuit.
SLAA540B – June 2012 – Revised June 2013
Submit Documentation Feedback
TLV320DAC3100 Test for Detection of Open Loads
Copyright © 2012–2013, Texas Instruments Incorporated
3
Test Procedure for Detection of Open Loads
www.ti.com
LBTL
Vin+
Vout+
Cg
RBTL/2
Cg
Vin–
LBTL
Vout–
RBTL/2
Figure 4. Equivalent Circuit for Analysis of the Differential Mode
L=
R L ´ 2
w0 æ RL ö
çç
÷ ´ 2
2 ÷ø
è
L=
2pf L=
4W´
2
2p(6 kHz) L = 150.053 µ
mH » 150 µ
mH
(3)
Further details regarding BD modulation and values for the inductors and capacitors can be found in:
Class-D LC Filter Design (SLOA119).
3
Test Procedure for Detection of Open Loads
The following steps use the TLV320DAC3100 EVM and its corresponding GUI. A USB-to-mini USB cable
is needed to connect the EVM to a computer or laptop.
3.1
Setup Considerations
To download the software, go to the TLV320DAC3120 EVM product folder under Related Products.
To install the GUI, first download the software. Then attach the EVM to the computer using the USB cable.
Next, open the .exe file named CodecControl and choose TLV320AIC3100EVM-U when the Select EVM
panel appears.
For hardware considerations, all of the jumpers on the EVM must be taken off the headers (W1, W2, W3),
because the layout is manually pulling MICDET to MICBIAS. See Figure 5 for an example. Table 2 also
lists the functionality of each header.
4
TLV320DAC3100 Test for Detection of Open Loads
Copyright © 2012–2013, Texas Instruments Incorporated
SLAA540B – June 2012 – Revised June 2013
Submit Documentation Feedback
Test Procedure for Detection of Open Loads
www.ti.com
Figure 5. EVM Board With No Jumpers
Table 2. Description of Headers
HEADER
DESCRIPTION
W1 (pins 1–2)
Analog volume control
W1 (pins 2–3)
Microphone detection
W2
Apply right-channel MICBIAS voltage to microphone connector
W3
Apply left-channel MICBIAS voltage to microphone connector
One can use pin 2 on header W1 to measure MICDET and R17 (on the back of the EVM) to measure
MICBIAS.
3.2
Steps in the GUI for Detection of Open Loads
There are four steps when using the GUI to test for open loads, assuming the speaker is already
connected to the EVM.
1. Enable headset detection (Page 0, Register 67, bit D7 should be set to 1).
2. Read the register (Register should read E0 or A0, as both detect a headset; see Table 1).
3. Disconnect the speaker by removing leads.
4. Read the register (Register should read 80).
3.2.1
Enable Headset Detection
Headset detection can be enabled through either Register Inspector or Command. It is not necessary to
enable headset detection using both Register Inspector and Command. Once changes have been enabled
using either process, the GUI automatically updates the information, which is reflected in the other.
NOTE: If MCLK is not used in the application, the internal oscillator must be enabled first before
performing the following steps. To enable the internal oscillator, use the Register Inspector.
Go to Page 3, Register 16, and change Bit 7 from 1 to 0.
To enable headset detection through Register Inspector, go to View → Register Inspector. Next, scroll
down to Register 67 and click on the 0 in column 67 to change it to a 1. The number turns red when
transitioning from one value to another to indicate the change. The advantage in using this process is
ease of use.
SLAA540B – June 2012 – Revised June 2013
Submit Documentation Feedback
TLV320DAC3100 Test for Detection of Open Loads
Copyright © 2012–2013, Texas Instruments Incorporated
5
Test Procedure for Detection of Open Loads
www.ti.com
To enable headset detection through Command, go to View → Command. Then in the command buffer,
type w 30 43 80 and click Run. w indicates write and 30,43, and 80 indicate the device address, register
(Register 67 in this instance), and data value, respectively, written in hex. The advantage in using this
process is the ability to insert multiple manual instructions as desired.
See Figure 6 and Figure 7 to enable headset detection using Register Inspector and Command,
respectively.
Figure 6. Enabling Headset Detection Using Register Inspector
6
TLV320DAC3100 Test for Detection of Open Loads
Copyright © 2012–2013, Texas Instruments Incorporated
SLAA540B – June 2012 – Revised June 2013
Submit Documentation Feedback
Test Procedure for Detection of Open Loads
www.ti.com
Figure 7. Enabling Headset Detection Using Command
3.2.2
Read Register
The easiest way to read a register value is through Command. In the text box, write r 30 43 01. r indicates
read and 30 and 43 indicate the device address and register (Register 67 in this instance) once again. 01
indicates the number of bytes read from the register. Click on Execute and the data appears in the Read
Data box. See Figure 8 for reading a register value from Command. Figure 3 shows the register values
transitioning between detecting a speaker and an open load.
SLAA540B – June 2012 – Revised June 2013
Submit Documentation Feedback
TLV320DAC3100 Test for Detection of Open Loads
Copyright © 2012–2013, Texas Instruments Incorporated
7
Other Considerations
www.ti.com
Figure 8. Reading a Register Using Command
4
Other Considerations
There are two factors to take into consideration when using the headset-detection circuitry: the capacitors
and the volume level of the device.
4.1
Capacitor Considerations
For capacitor considerations, see the 220-μF dc-blocking capacitors in Section 2. When picking
capacitors, the larger the capacitor, the more efficiently dc bias is eliminated, and there is less chance for
a false reading: false reading meaning the register reads that a speaker is connected when it is actually
disconnected and vice versa. However, the charge and discharge times are also longer. This timing
means that when the speaker is disconnected, it takes a longer period of time before MICDET reaches
0.91 x MICDET and is considered disconnected.
The same logic goes to smaller capacitors. Whereas smaller capacitors have faster charge and discharge
times, and therefore detect a disconnected speaker more quickly, these capacitors also block dc bias less
efficiently with a greater chance for false readings.
Based off the headset-detection circuitry and using a Mirage 5.1 Nanosat or equivalent speaker, the
minimum capacitor value is 10-μF, though the capacitor value should be chosen based on the system and
speakers used.
4.2
Volume Level Considerations
As the purpose of the capacitors is to block out dc bias, the ac signal will passes through the capacitors
into the speakers. Therefore, some ac signal can also be seen on the MICDET pin. To ensure that the
MICDET pin does not exceed absolute maximum (AVDD + 0.3 V, or 3.6 V in this case), the ac signal on
the MICDET pin must be limited to 0.3 Vpeak at the most.
To help limit the ac signal seen on the MICDET pin, either the Class-D Speaker Driver, Analog
Attenuation, or both (see Figure 9) must be moderated so that neither of the two is at the highest setting.
See Table 3 for a summary of Class-D Speaker Driver levels versus Analog Attenuation levels as to not
exceed absolute maximum rating for MICDET.
8
TLV320DAC3100 Test for Detection of Open Loads
Copyright © 2012–2013, Texas Instruments Incorporated
SLAA540B – June 2012 – Revised June 2013
Submit Documentation Feedback
Summary
www.ti.com
Figure 9. Volume Level Section of EVM GUI
Table 3. Class-D Speaker Driver and Analog
Attenuation Levels for MICDET
5
Class-D Speaker Driver (dB)
Analog Attenuation (max) (dB)
6
0
12
0
18
–10
24
–10
Summary
Open loads can be detected using the EVM GUI by first enabling headset detect, then reading register 67.
Headset detection works by having MICDET pulled to MICBIAS. When a headset is inserted, MICDET
drops to ground. The test for detection of open loads works in the same way by using the function for
headset detection to indicate load connectivity.
Revision History
Changes from A Revision (March 2013) to B Revision .................................................................................................. Page
•
•
•
Added REGISTER VALUE column to table ........................................................................................... 1
Changed connector to cable in Section 3 ............................................................................................. 4
Added note to Section 3.2.1 ............................................................................................................ 5
NOTE: Page numbers for previous revisions may differ from page numbers in the current version.
SLAA540B – June 2012 – Revised June 2013
Submit Documentation Feedback
Revision History
Copyright © 2012–2013, Texas Instruments Incorporated
9
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
Automotive and Transportation
www.ti.com/automotive
Amplifiers
amplifier.ti.com
Communications and Telecom
www.ti.com/communications
Data Converters
dataconverter.ti.com
Computers and Peripherals
www.ti.com/computers
DLP® Products
www.dlp.com
Consumer Electronics
www.ti.com/consumer-apps
DSP
dsp.ti.com
Energy and Lighting
www.ti.com/energy
Clocks and Timers
www.ti.com/clocks
Industrial
www.ti.com/industrial
Interface
interface.ti.com
Medical
www.ti.com/medical
Logic
logic.ti.com
Security
www.ti.com/security
Power Mgmt
power.ti.com
Space, Avionics and Defense
www.ti.com/space-avionics-defense
Microcontrollers
microcontroller.ti.com
Video and Imaging
www.ti.com/video
RFID
www.ti-rfid.com
OMAP Applications Processors
www.ti.com/omap
TI E2E Community
e2e.ti.com
Wireless Connectivity
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2013, Texas Instruments Incorporated