TI TAS5716

TAS5716
www.ti.com............................................................................................................................................................................................... SLOS569 – JANUARY 2009
20-W Stereo Digital-Audio Power Amplifier With EQ and DRC
FEATURES
1
• Audio Input/Output
– 20 W Into an 8-Ω Load From an 18-V Supply
– Two Serial Audio Inputs (Four Audio
Channels)
– Supports Multiple Output Configurations:
– 2-Ch Bridged Outputs (20 W × 2)
– 4-Ch Single-Ended Outputs (10 W × 4)
– 2-Ch Single-Ended + 1-Ch Bridged (2.1)
(10 W × 2 + 20 W)
• Closed-Loop Power-Stage Architecture
– Improved PSRR Reduces Power Supply
Performance Requirements
– Higher Damping Factor Provides for
Tighter, More Accurate Sound With
Improved Bass Response
– Constant Output Power Over Variation in
Supply
• Wide PVCC Range From (10 V to 26 V)
– No Separate Supply Required for Gate
Drive
• Supports 32-kHz–192-kHz Sample Rates
(LJ/RJ/I2S)
• Headphone PWM Outputs
• Subwoofer PWM Outputs
• AM Interference Avoidance Support
• Audio/PWM Processing
– Independent Channel Volume Controls With
24-dB to –100-dB Range—Soft Mute (50%
Duty Cycle)
– Programmable Dynamic Range Control
– 16 Programmable Biquads for Speaker
Equalization
– Adaptive Biquad Coefficients for EQ and
DRC Filters
– Programmable Input and Output Mixers
23
•
– Loudness Compensation for Subwoofer
– Automatic Sample-Rate Detection and
Coefficient Banking
– 3D Support
– Pseudo-Bass Support
General Features
– Serial Control Interface Operational Without
MCLK
– Factory-Trimmed Internal Oscillator Avoids
the Need for External Crystal
– Surface Mount, 64-Terminal, 10-mm ×
10-mm HTQFP Package
– Thermal and Short-Circuit Protection
DESCRIPTION
The TAS5716 is a 20-W, efficient, digital-audio power
amplifier for driving stereo bridged-tied speakers. Two
serial data inputs allow processing of up to four
discrete audio channels and seamless integration to
most digital audio processors and MPEG decoders,
accepting a wide range of input data and clock rates.
A fully programmable data path allows these
channels to be routed to the internal speaker drivers
or output via the subwoofer or headphone PWM
outputs.
The TAS5716 is a slave-only device receiving all
clocks from external sources. The TAS5716 operates
at a 384-kHz switching rate for 32-, 48-, 96-, and
192-kHz data, and at a 352.8 kHz switching rate for
44.1-, 88.2-, and 176.4-kHz data. The 8×
oversampling combined with the fourth-order noise
shaper provides a flat noise floor and excellent
dynamic range from 20 Hz to 20 kHz.
1
2
3
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas
Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
PurePath Digital is a trademark of Texas Instruments.
All other trademarks are the property of their respective owners.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2009, Texas Instruments Incorporated
TAS5716
SLOS569 – JANUARY 2009............................................................................................................................................................................................... www.ti.com
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
SIMPLIFIED APPLICATION DIAGRAMS
Bridge-Tied Load (BTL) Mode
3.3 V
10 V–26 V
DVDD/AVDD
AVCC/PVCC
OUT_A
LRCLK
SCLK
Digital
Audio
Source
BST_A
MCLK
SDIN1
LCBTL*
Left
LCBTL*
Right
BST_B
SDIN2
OUT_B
2
SDA
I C
Control
OUT_C
SCL
BST_C
BST_D
MUTE
HPSEL
Control
Inputs
OUT_D
RESET
10 V–26 V
TAS5601
PDN
SUB_PWM+
PWM_AP
OUT_A
PWM_AN
PLL_FLTP
SUB_PWM–
PWM_BP
BST_A
LCBTL*
Subwoofer
BST_B
Loop
Filter
PWM_BN
PLL_FLTM
BKND_ERR
FAULT
VALID
RESET
OUT_B
HPR_PWM
HPL_PWM
RC
Filter
TPA6110A2
(HP Amplifier)
* Refer to TI Application Note (SLOA119) on LC filter design for BTL (AD/BD mode) configuration.
B0264-02
2
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s): TAS5716
TAS5716
www.ti.com............................................................................................................................................................................................... SLOS569 – JANUARY 2009
Single-Ended (SE) 2.1 Mode
3.3 V
10 V–26 V
DVDD/AVDD
AVCC/PVCC
OUT_A
LCSE*
LRCLK
SCLK
Digital
Audio
Source
BST_A
MCLK
SDIN1
SDIN2
BST_B
OUT_B
2
LCSE*
SDA
I C
Control
SCL
MUTE
OUT_C
HPSEL
Control
Inputs
RESET
PDN
BST_C
LCBTL*
BST_D
OUT_D
PLL_FLTP
Loop
Filter
SUB_PWM+
PLL_FLTM
SUB_PWM–
BKND_ERR
VALID
HPR_PWM
HPL_PWM
RC
Filter
TPA6110A2
(HP Amplifier)
* Refer to TI Application Note (SLOA119) on LC filter design for SE or BTL configuration.
B0264-05
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s): TAS5716
3
TAS5716
SLOS569 – JANUARY 2009............................................................................................................................................................................................... www.ti.com
Single-Ended (SE) 4.0 Mode
3.3 V
10 V–26 V
DVDD/AVDD
AVCC/PVCC
OUT_A
LCSE*
LRCLK
SCLK
Digital
Audio
Source
BST_A
MCLK
SDIN1
SDIN2
2
BST_B
OUT_B
LCSE*
OUT_C
LCSE*
SDA
I C
Control
SCL
MUTE
HPSEL
Control
Inputs
RESET
BST_C
PDN
BST_D
OUT_D
LCSE*
PLL_FLTP
Loop
Filter
SUB_PWM+
PLL_FLTM
SUB_PWM–
BKND_ERR
VALID
HPR_PWM
HPL_PWM
RC
Filter
TPA6110A2
(HP Amplifier)
* Refer to TI Application Note (SLOA119) on LC filter design for SE configuration.
B0264-04
4
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s): TAS5716
TAS5716
www.ti.com............................................................................................................................................................................................... SLOS569 – JANUARY 2009
FUNCTIONAL VIEW
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s): TAS5716
5
6
Submit Documentation Feedback
Product Folder Link(s): TAS5716
Dolby
down
mix
R
L
6 sub
Sum/
2
Vol4
´
´
Vol3
sc3
sc2
sc1
7 BQ EQ
7 BQ EQ
ealpha
ealpha
BQ
0
Vol2
´
´
Vol1
<<
BQ
ealpha
ealpha
>>
NOTES: Nodes identified with red text are turned ON.
To write to the input mixers (0x96, 0x99, 0xA9, 0xAA), follow the sequence described on page 40.
1–4
+
+
V2IM2 0x099
+
V2 IMDMR0x0AA
´
´
´
V1 IMDML0x0A9
´
V1IM1 0x096
Vol
Energy
MAXMUX
10 dB
1–4
4 RS
3 LS
2 RF
1 LF
´
ealpha
Loudness
DRC2
BQ
Master
ON/ OFF
Attack
DRC1 Decay
1
1
´
´
Master
ON/OFF
Attack
Decay
´
´
´
+
V1OM3 0x51[1]
+
B0296-01
V2OM4 0x52[1]
V2OM6 0x52[2]
´
´
´
V2OM2 0x52[0]
´
´
V1OM1 0x51[0]
TAS5716
SLOS569 – JANUARY 2009............................................................................................................................................................................................... www.ti.com
DAP Process Flow
Input Muxing
Copyright © 2009, Texas Instruments Incorporated
TAS5716
www.ti.com............................................................................................................................................................................................... SLOS569 – JANUARY 2009
64-PIN, HTQFP PACKAGE
PIN FUNCTIONS
PIN
NAME
TYPE
NO.
(1)
5-V
TOLERANT
TERMINATION
DESCRIPTION
(2)
AGND
57
P
Analog ground for power stage
AVCC
58
P
Analog power supply for power stage. Connect externally to same
potential as PVCC.
AVDD
10
P
3.3-V analog power supply
AVSS
11
P
Analog 3.3-V supply ground
BKND_ERR
35
DI
(1)
(2)
Pullup
Active-low. A back-end error sequence is generated by applying logic
LOW to this terminal. This terminal is connected to an external power
stage. If no external power stage is used, connect this terminal directly
to DVDD.
TYPE: A = analog; D = 3.3-V digital; P = power/ground/decoupling; I = input; O = output
All pullups are 20-µA weak pullups and all pulldowns are 20-µA weak pulldowns. The pullups and pulldowns are included to assure
proper input logic levels if the terminals are left unconnected (pullups → logic 1 input; pulldowns → logic 0 input). Devices that drive
inputs with pullups must be able to sink 20 µA while maintaining a logic-0 drive level. Devices that drive inputs with pulldowns must be
able to source 20 µA while maintaining a logic-1 drive level.
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s): TAS5716
7
TAS5716
SLOS569 – JANUARY 2009............................................................................................................................................................................................... www.ti.com
PIN FUNCTIONS (continued)
PIN
NAME
TYPE
NO.
(1)
5-V
TOLERANT
TERMINATION
DESCRIPTION
(2)
BST_A
59
P
High-side bootstrap supply for half-bridge A
BST_B
61
P
High-side bootstrap supply for half-bridge B
BST_C
53
P
High-side bootstrap supply for half-bridge C
BST_D
55
P
High-side bootstrap supply for half-bridge D
BYPASS
56
O
Nominally equal to VCC/8. Internal reference voltage for analog cells
DVDD
15,
33
P
3.3-V digital power supply
DVSS
20,
26
P
Digital ground
HPL_PWM
37
DO
HPR_PWM
38
DO
HPSEL
30
DI
5-V
Headphone select, active high. When a logic HIGH is applied, device
enters headphone mode and speakers are hard-muted. When a logic
LOW is applied, device is in speaker mode and headphone outputs
become line outputs or are disabled.
LRCLK
22
DI
5-V
Input serial audio data left/right clock (sampling rate clock)
MCLK
34
DI
5-V
MCLK is the clock master input. The input frequency of this clock can
range from 2.822 MHz to 49 MHz.
MUTE
21
DI
5-V
OSC_RES
19
AO
OUT_A
4, 5
O
Output, half-bridge A
OUT_B
1, 64
O
Output, half-bridge B
OUT_C
49,
50
O
Output, half-bridge C
OUT_D
45,
46
O
Output, half-bridge D
PDN
17
DI
PGND_A
6, 7
P
Power ground for half-bridge A
PGND_B
2, 3
P
Power ground for half-bridge B
PGND_C
47,
48
P
Power ground for half-bridge C
PGND_D
43,
44
P
Power ground for half-bridge D
PLL_FLTM
12
AO
PLL negative input
PLL_FLTP
13
AI
PLL positive input
PVCC_A
8, 9
P
Power supply input for half-bridge output A
PVCC_B
62,
63
P
Power supply input for half-bridge output B
PVCC_C
51,
52
P
Power supply input for half-bridge output C
PVCC_D
41,
42
P
Power supply input for half-bridge output D
8
Headphone left-channel PWM output
Headphone right-channel PWM output
Pullup
Performs a soft mute of outputs, active-low. A logic low on this
terminal sets the outputs equal to 50% duty cycle. A logic high on this
terminal allows normal operation. The mute control provides a
noiseless volume ramp to silence. Releasing mute provides a
noiseless ramp to previous volume.
Oscillator trim resistor. Connect an 18.2-kΩ resistor to GND.
5-V
Pullup
Power down, active-low. PDN powers down all logic, stops all clocks,
and outputs stops switching. When PDN is released, the device
powers up all logic, starts all clocks, and performs a soft start that
returns to the previous configuration determined by register settings.
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s): TAS5716
TAS5716
www.ti.com............................................................................................................................................................................................... SLOS569 – JANUARY 2009
PIN FUNCTIONS (continued)
PIN
NAME
TYPE
(1)
5-V
TOLERANT
TERMINATION
(2)
DESCRIPTION
Pullup
Reset, active-low. A system reset is generated by applying a logic low
to this terminal. RESET is an asynchronous control signal that
restores the DAP to its default conditions, sets the VALID outputs low,
and places the PWM in the hard-mute state (stops switching). Master
volume is immediately set to full attenuation. Upon the release of
RESET, if PDN is high, the system performs a 4- to 5-ms device
initialization and sets the volume at mute.
NO.
RESET
16
DI
5-V
SCL
29
DI
5-V
I2C serial-control clock input
SCLK
23
DI
5-V
Serial audio data clock (shift clock). SCLK is the serial audio-port input
data-bit clock.
SDA
28
DIO
5-V
I2C serial-control data-interface input/output
SDIN1
25
DI
5-V
Serial audio data-1 input is one of the serial data input ports. SDIN1
supports three discrete (stereo) data formats.
SDIN2
24
DI
5-V
Serial audio data-2 input is one of the serial data input ports. SDIN2
supports three discrete (stereo) data formats.
STEST
31
DI
Test terminal. Connect directly to GND.
SUB_PWM–
39
DO
Subwoofer negative PWM output
SUB_PWM+
40
DO
Subwoofer positive PWM output
TEST2
32
DI
Test terminal. Connect directly to DVDD.
VALID
36
DO
Output indicating validity of ALL PWM channels, active-high. This
terminal is connected to an external power stage. If no external power
stage is used, leave this terminal floating.
VCLAMP_AB
60
P
Internally generated voltage supply for channels A and B gate drive.
Not to be used as a supply or connected to any component other than
the decoupling capacitor
VCLAMP_CD
54
P
Internally generated voltage supply for channels C and D gate drive.
Not to be used as a supply or connected to any component other than
the decoupling capacitor
VR_ANA
14
P
Internally regulated 1.8-V analog supply voltage. This terminal must
not be used to power external devices.
VR_DIG
27
P
Internally regulated 1.8-V digital supply voltage. This terminal must not
be used to power external devices.
VREG_EN
18
DI
Pulldown
Voltage regulator enable. Connect directly to GND.
ABSOLUTE MAXIMUM RATINGS
over operating free-air temperature range (unless otherwise noted)
Supply voltage
Input voltage
(1)
VALUE
UNIT
DVDD, AVDD
–0.3 to 3.6
V
PVCC
–0.3 to 30
V
–0.5 to DVDD + 0.5
V
3.3-V digital input
5-V tolerant (2) digital input
Input clamp current, IIK (VI < 0 or VI > 1.8 V
Output clamp current, IOK (VO < 0 or VO > 1.8 V
–0.5 to 6
V
±20
mA
±20
mA
Operating free-air temperature
0 to 85
°C
Operating junction temperature range
0 to 150
°C
–40 to 125
°C
Storage temperature range, Tstg
(1)
(2)
Stresses beyond those listed under absolute ratings may cause permanent damage to the device. These are stress ratings only and
functional operation of the device at these or any other conditions beyond those indicated under recommended operation conditions are
not implied. Exposure to absolute-maximum conditions for extended periods may affect device reliability.
5-V tolerant inputs are PDN, RESET, MUTE, SCLK, LRCLK, MCLK, SDIN1, SDIN2, SDA, SCL, and HPSEL.
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s): TAS5716
9
TAS5716
SLOS569 – JANUARY 2009............................................................................................................................................................................................... www.ti.com
DISSIPATION RATINGS
PACKAGE (1)
DERATING FACTOR
TA = 25°C
POWER RATING
TA = 45°C
POWER RATING
TA = 70°C
POWER RATING
10-mm × 10-mm QFP
29 mW/°C
2.89 W
2.31 W
1.59 W
(1)
For the most current package and ordering information, see the Package Option Addendum at the end of this document, or see the TI
website at www.ti.com.
RECOMMENDED OPERATING CONDITIONS
over operating free-air temperature range (unless otherwise noted)
MIN
NOM
MAX
UNIT
3
3.3
3.6
V
26
V
Digital/analog supply voltage
DVDD
Half-bridge supply voltage
PVCC_xx
VIH
High-level input voltage
3.3-V TTL, 5-V tolerant
VIL
Low-level input voltage
3.3-V TTL, 5-V tolerant
0.8
V
TA
Operating ambient temperature range
0
85
°C
TJ
Operating junction temperature range
0
150
°C
10
2
RL (BTL)
RL (SE)
Output filter: L = 22 µH, C = 680 nF
Load impedance
RL (PBTL)
V
6.0
8
3.2
4
3.2
4
LO (BTL)
Ω
10
LO (SE)
Minimum output inductance under
short-circuit condition
Output-filter inductance
µH
10
LO (PBTL)
10
PWM OPERATION AT RECOMMENDED OPERATING CONDITIONS
PARAMETER
Output sample rate 2×–1×
oversampled
TEST CONDITIONS
MODE
32-kHz data rate ±2%
12× sample rate
VALUE
UNITS
384
44.1-, 88.2-, 176.4-kHz data rate ±2%
kHz
8×, 4×, and 2× sample rates
352.8
48-, 96-, 192-kHz data rate ±2%
kHz
8×, 4×, and 2× sample rates
384
kHz
PLL INPUT PARAMETERS AND EXTERNAL FILTER COMPONENTS
PARAMETER
fMCLKI
TEST CONDITIONS
MIN
Frequency, MCLK (1 / tcyc2)
TYP
2.822
MCLK duty cycle
40%
50%
UNIT
49
MHz
60%
MCLK minimum high time
≥2-V MCLK = 49.152 MHz, within the
minimum and maximum duty-cycle
constraints
8
ns
MCLK minimum low time
≤0.8-V MCLK = 49.152 MHz, within the
minimum and maximum duty-cycle
constraints
8
ns
LRCLK allowable drift before LRCLK reset
10
MAX
10
MCLKs
External PLL filter capacitor C1
SMD 0603 Y5V
47
nF
External PLL filter capacitor C2
SMD 0603 Y5V
4.7
nF
External PLL filter resistor R
SMD 0603, metal film
470
Ω
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s): TAS5716
TAS5716
www.ti.com............................................................................................................................................................................................... SLOS569 – JANUARY 2009
ELECTRICAL CHARACTERISTICS
DC Characteristics, TA = 25°C, PVCC_X, AVCC = 18 V, RL = 8 Ω (unless otherwise noted)
PARAMETER
TEST CONDITIONS
VOH
High-level output voltage
3.3-V TTL and 5-V tolerant
(1)
IOH = –4 mA
VOL
Low-level output voltage
3.3-V TTL and 5-V tolerant
(1)
IOL = 4 mA
| VOS |
Class-D output offset voltage
VBYPASS
PVCC/8 reference for analog section
IIL
Low-level input current
IIH
High-level input current
MIN
TYP MAX
2.4
V
0.5
±26
No load
2.2
2.26
VI = VIL
±2
5-V tolerant (1)
VI = 0 V, DVDD = 3 V
±2
3.3-V TTL
VI = VIH
5-V tolerant
VI = 5.5 V, DVDD = 3 V
±2
±20
43
65
80
2
8
16
33
V
µA
µA
IDD
Input supply current
Reset (RESET = LOW)
11
23
ICC
Quiescent supply current
No load
14
33
57
mA
ICC(RESET)
Quiescent supply current in reset mode
No load
58
176
µA
ICC(PDNZ)
Quiescent supply current in power-down mode
No load
58
176
µA
PSRR
DC power-supply rejection ratio
PVCC = 17.5 V to 18.5 V
60
Drain-source on-state resistance, high-side
VCC = 18 V , IO = 500 mA,
TJ = 25°C
240
RDS(on)
Supply voltage (DVDD, AVDD)
Power down
(PDNZ = LOW)
V
mV
2.3
3.3-V TTL
Normal mode
UNIT
Low-side
Total
tON
tOFF
(1)
Turnon time (BTL mode) (Set Reg 0x1A bit 7 to 0)
Turnoff time (SE mode) (Set Reg 0X1A bit 7 to 1)
C(BYPASS) = 1 µF,
Time required for C(BYPASS)
to reach its final value
Turnoff time (BTL mode) (Set Reg 0X1A bit 7 to 0)
dB
240
480
Turnon time (SE mode) (Set Reg 0x1A bit 7 to 1)
mA
mΩ
850
500
30
500
30
ms
ms
5-V tolerant pins are PDN, RESET, MUTE, SCLK, LRCLK, MCLK, SDIN1, SDIN2, SDA, SCL, and HPSEL.
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s): TAS5716
11
TAS5716
SLOS569 – JANUARY 2009............................................................................................................................................................................................... www.ti.com
AC Characteristics, TA = 25°C, PVCC_X, AVCC = 18 V, AVDD, DVDD = 3.3 V, RL = 8 Ω (unless
otherwise noted) (1)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
KSVR
Supply ripple rejection
100-mVPP ripple at 20 Hz–20 kHz, BTL, 50%
duty cycle PWM
–60
dB
PO
Continuous output
power
BTL (RL = 8 Ω, THD+N = 10%, f = 1 kHz,
PVCC = 18 V)
20.6
W
BTL (RL = 8 Ω, THD+N = 7%, f = 1 kHz,
PVCC = 18 V)
19.3
W
SE (RL = 4 Ω, THD+N = 10%, f = 1 kHz,
PVCC = 24 V)
18.1
W
SE (RL = 4 Ω, THD+N = 7%, f = 1 kHz, PVCC
= 24 V)
17.3
W
THD+N
Vn
Total harmonic distortion VCC = 24 V, RL = 4 Ω, f = 1 kHz, PO = 10 W
+ noise (SE)
(half-power)
0.08%
Total harmonic distortion VCC = 18 V, RL = 8 Ω, f = 1 kHz, PO = 10 W
+ noise (BTL)
(half-power)
0.05%
20 Hz to 22 kHz (BD mode)
115
µV
A-weighted filter; MUTE = LOW
–82
dBV
PO = 1 W, f = 1 kHz
–69
dB
99
dB
Thermal trip point
(output shut down,
unlatched fault)
150
°C
Thermal hysteresis
15
°C
Output integrated noise
Crosstalk
SNR
(1)
Signal-to-noise ratio
Maximum output at THD+N < 1%, f = 1 kHz,
A-weighted
All measurement in AD mode.
AC Characteristics, TA = 25°C, PVCC_X, AVCC = 12 V, AVDD, DVDD = 3.3 V, RL = 8 Ω (unless
otherwise noted) (1)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
KSVR
Supply ripple rejection
100-mVpp ripple at 20 Hz–20 kHz, BTL,
50% duty cycle PWM
–60
dB
PO
Continuous output power
BTL (RL = 8 Ω, THD+N = 10%, f = 1 kHz)
9.2
W
BTL (RL = 8 Ω, THD+N = 7%, f = 1 kHz)
8.7
W
SE (RL = 4 Ω, THD+N = 10%, f = 1 kHz)
4.5
W
SE (RL = 4 Ω, THD+N = 7%, f = 1 kHz)
4.2
W
THD+N
Total harmonic distortion
+ noise (BTL)
VCC = 12 V, RL = 8 Ω, f = 1 kHz,
PO = 5 W (half-power)
Vn
Output integrated noise
20 Hz to 22 kHz (BD mode)
115
µV
A-weighted filter
–82
dBV
PO = 1 W, f = 1 kHz
–75
dB
96
dB
150
°C
15
°C
Crosstalk
SNR
Signal-to-noise ratio
Maximum output at THD+N < 1%,
f = 1 kHz, A-weighted
Thermal trip point (output
shutdown, unlatched fault)
Thermal hysteresis
(1)
12
0.07%
All measurement in AD mode.
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s): TAS5716
TAS5716
www.ti.com............................................................................................................................................................................................... SLOS569 – JANUARY 2009
SERIAL AUDIO PORTS SLAVE MODE
over recommended operating conditions (unless otherwise noted)
TEST
CONDITIONS
PARAMETER
CL = 30 pF
MIN
TYP
1.024
MAX
UNIT
12.288
MHz
fSCLKIN
Frequency, SCLK 32 × fS, 48 × fS, 64 × fS
tsu1
Setup time, LRCLK to SCLK rising edge
10
ns
th1
Hold time, LRCLK from SCLK rising edge
10
ns
tsu2
Setup time, SDIN to SCLK rising edge
10
ns
th2
Hold time, SDIN from SCLK rising edge
10
LRCLK frequency
32
48
192
SCLK duty cycle
40%
50%
60%
LRCLK duty cycle
40%
50%
60%
32
64
SCLK
edges
–1/4
1/4
SCLK
period
SCLK rising edges between LRCLK rising edges
t(edge)
LRCLK clock edge with respect to the falling edge of SCLK
ns
kHz
Figure 1. Slave-Mode Serial-Data Interface Timing
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s): TAS5716
13
TAS5716
SLOS569 – JANUARY 2009............................................................................................................................................................................................... www.ti.com
I2C SERIAL CONTROL PORT OPERATION
Timing characteristics for I2C Interface signals over recommended operating conditions (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
No wait states
MAX
UNIT
400
kHz
fSCL
Frequency, SCL
tw(H)
Pulse duration, SCL high
0.6
tw(L)
Pulse duration, SCL low
1.3
tr
Rise time, SCL and SDA
300
ns
tf
Fall time, SCL and SDA
300
ns
tsu1
Setup time, SDA to SCL
th1
Hold time, SCL to SDA
t(buf)
µs
µs
100
ns
0
ns
Bus free time between stop and start conditions
1.3
µs
tsu2
Setup time, SCL to start condition
0.6
µs
th2
Hold time, start condition to SCL
0.6
µs
tsu3
Setup time, SCL to stop condition
0.6
CL
Load capacitance for each bus line
µs
400
tw(H)
tw(L)
pF
tf
tr
SCL
tsu1
th1
SDA
T0027-01
Figure 2. SCL and SDA Timing
SCL
t(buf)
th2
tsu2
tsu3
SDA
Start
Condition
Stop
Condition
T0028-01
Figure 3. Start and Stop Conditions Timing
14
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s): TAS5716
TAS5716
www.ti.com............................................................................................................................................................................................... SLOS569 – JANUARY 2009
RESET TIMING (RESET)
Control signal parameters over recommended operating conditions (unless otherwise noted)
PARAMETER
MIN
td(VALID_LOW)
Time to assert VALID (reset to power stage) low
tw(RESET)
Pulse duration, RESET active
td(I2C_ready)
Time to enable I2C
td(run)
Device start-up time (after start-up command via I2C)
TYP
MAX
UNIT
300
ns
1
ms
3.5
ms
10
RESET
ms
Earliest time
that hard mute
could be exited
tw(RESET)
VALID
td(I2C_ready)
td(run)
td(VALID_LOW)
System initialization.
Start system
2
Enable via I C.
T0029-05
Figure 4. Reset Timing
POWER-DOWN (PDN) TIMING
Control signal parameters over recommended operating conditions (unless otherwise noted)
PARAMETER
MIN
TYP
MAX
UNIT
td(VALID_LOW)
Time to assert VALID (reset to power stage) low
725
µs
td(STARTUP)
Device startup time
120
ms
tw
Minimum pulse duration required
800
ns
PDN
tw
VALID
td(VALID_LOW)
td(STARTUP)
T0030-04
Figure 5. Power-Down Timing
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s): TAS5716
15
TAS5716
SLOS569 – JANUARY 2009............................................................................................................................................................................................... www.ti.com
BACK-END ERROR (BKND_ERR)
Control signal parameters over recommended operating conditions (unless otherwise noted)
PARAMETER
MIN
tw(ER)
Pulse duration, BKND_ERR active (active-low)
tp(valid_high)
Programmable. Time to stay in the OUT_x low state. After tp(valid_high), the TAS5716
attempts to bring the system out of the OUT_x low state if BKND_ERR is high. See
register 0x1C.
tp(valid_low)
TYP
MAX
UNIT
350
None
ns
ms
Time TAS5716 takes to bring OUT_x low after BKND_ERR assertion.
350
ns
tw(ER)
BKND_ERR
VALID
Normal
Operation
Normal
Operation
tp(valid_high)
tp(valid_low)
T0031-04
Figure 6. Error Recovery Timing
MUTE TIMING (MUTE)
Control signal parameters over recommended operating conditions (unless otherwise noted)
PARAMETER
td(VOL)
(1)
MIN
Volume ramp time. Ramp time = number of steps (programmable number of steps, see
register 0x0E) × step size (1)
TYP
MAX
1024
UNIT
steps
Stepsize = 4 LRCLKs (for 32–48 kHz sample rate); 8 LRCLKs (for 88.2–96 kHz sample rate); 16 LRCLKs (for 176.4–192 kHz sample
rate)
MUTE
VOLUME
Normal
Operation
Normal
Operation
td(VOL)
td(VOL)
50-50
Duty Cycle
T0032-03
Figure 7. Mute Timing
16
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s): TAS5716
TAS5716
www.ti.com............................................................................................................................................................................................... SLOS569 – JANUARY 2009
HEADPHONE SELECT (HPSEL)
PARAMETER
tw(MUTE)
Pulse duration, HPSEL active
td(VOL)
Soft volume update time
t(SW)
Switch-over time
(1)
MIN
MAX
350
None
See
(1)
0.2
UNIT
ns
ms
1
ms
Defined by rate setting. See the Volume Configuration Register section.
Figure 8 and Figure 9 show functionality when bit 4 in HP configuration register is set to DISABLE line output from HP_PWM outputs. If
bit 4 is not set, than the HP PWM outputs are not disabled when HPSEL is brought low.
HPSEL
Spkr Volume
td(VOL)
HP Volume
td(VOL)
t(SW)
VALID
T0267-01
Figure 8. HPSEL Timing for Headphone Insertion
HPSEL
HP Volume
td(VOL)
Spkr Volume
td(VOL)
t(SW)
VALID
T0268-01
Figure 9. HPSEL Timing for Headphone Extraction
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s): TAS5716
17
TAS5716
SLOS569 – JANUARY 2009............................................................................................................................................................................................... www.ti.com
TYPICAL CHARACTERISTICS, BTL CONFIGURATION
TOTAL HARMONIC DISTORTION + NOISE (BTL)
vs
FREQUENCY
TOTAL HARMONIC DISTORTION + NOISE (BTL)
vs
FREQUENCY
10
THD+N − Total Harmonic Distortion + Noise − %
THD+N − Total Harmonic Distortion + Noise − %
10
VCC = 12 V
RL = 8 Ω
P=5W
1
P = 2.5 W
0.1
0.01
P = 0.5 W
0.001
20
100
1k
VCC = 18 V
RL = 8 Ω
P = 10 W
1
P=5W
0.1
0.01
P=1W
0.001
20
10k 20k
100
1k
f − Frequency − Hz
10k 20k
f − Frequency − Hz
G001
G002
Figure 10.
Figure 11.
TOTAL HARMONIC DISTORTION + NOISE (BTL)
vs
FREQUENCY
TOTAL HARMONIC DISTORTION + NOISE (BTL)
vs
OUTPUT POWER
10
THD+N − Total Harmonic Distortion + Noise − %
THD+N − Total Harmonic Distortion + Noise − %
10
VCC = 24 V
RL = 8 Ω
P = 10 W
1
P=5W
0.1
0.01
P=1W
0.001
20
100
1k
10k 20k
VCC = 12 V
RL = 8 Ω
1
f = 10 kHz
f = 1 kHz
0.1
0.01
f = 20 Hz
0.001
0.01
f − Frequency − Hz
G003
Figure 12.
18
0.1
1
PO − Output Power − W
10
40
G004
Figure 13.
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s): TAS5716
TAS5716
www.ti.com............................................................................................................................................................................................... SLOS569 – JANUARY 2009
TYPICAL CHARACTERISTICS, BTL CONFIGURATION (continued)
TOTAL HARMONIC DISTORTION + NOISE (BTL)
vs
OUTPUT POWER
TOTAL HARMONIC DISTORTION + NOISE (BTL)
vs
OUTPUT POWER
10
THD+N − Total Harmonic Distortion + Noise − %
THD+N − Total Harmonic Distortion + Noise − %
10
VCC = 18 V
RL = 8 Ω
1
f = 10 kHz
f = 1 kHz
0.1
0.01
f = 20 Hz
0.001
0.01
0.1
1
10
PO − Output Power − W
VCC = 24 V
RL = 8 Ω
1
f = 10 kHz
f = 1 kHz
0.1
0.01
f = 20 Hz
0.001
0.01
40
0.1
1
G005
40
G006
Figure 14.
Figure 15.
EFFICIENCY
vs
OUTPUT POWER
SUPPLY CURRENT
vs
TOTAL OUTPUT POWER
3.0
100
RL = 8 Ω
90
2.5
VCC = 18 V
70
VCC = 24 V
VCC = 18 V
60
ICC − Supply Current − A
80
Efficiency − %
10
PO − Output Power − W
VCC = 12 V
50
40
30
2.0
VCC = 12 V
1.5
1.0
VCC = 24 V
20
0.5
10
RL = 8 Ω
0.0
0
0
5
10
15
20
25
PO − Output Power (Per Channel) − W
30
0
5
10
15
20
25
30
35
PO − Total Output Power − W
G007
Figure 16.
40
G008
Figure 17.
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s): TAS5716
19
TAS5716
SLOS569 – JANUARY 2009............................................................................................................................................................................................... www.ti.com
TYPICAL CHARACTERISTICS, BTL CONFIGURATION (continued)
OUTPUT POWER
vs
SUPPLY VOLTAGE
PSRR
vs
PVCC
40
0
RL = 8 Ω
35
−10
−20
−30
THD+N = 10%
25
PSRR − dB
PO − Output Power − W
30
20
15
THD+N = 1%
−40
−50
−60
−70
10
−80
5
−90
0
10
12
14
16
18
20
22
24
12
16
18
20
G009
22
24
26
G010
Figure 18.
Figure 19.
A-WTD NOISE
vs
PVCC
CROSSTALK
vs
FREQUENCY
−75
−40
−76
−50
−77
−60
−78
−70
Right to Left
−79
−80
−81
−80
−100
−110
−83
−120
−84
−130
10
12
14
16
18
20
22
24
Left to Right
−90
−82
−85
RL = 8 Ω
VCC = 12 V
−140
20
26
PVCC − V
G011
Figure 20.
20
14
PVCC − V
Crosstalk − dB
A-Wtd Noise − dBV
VCC − Supply Voltage − V
−100
10
26
100
1k
10k 20k
f − Frequency − Hz
G012
Figure 21.
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s): TAS5716
TAS5716
www.ti.com............................................................................................................................................................................................... SLOS569 – JANUARY 2009
TYPICAL CHARACTERISTICS, BTL CONFIGURATION (continued)
CROSSTALK
vs
FREQUENCY
CROSSTALK
vs
FREQUENCY
−40
−40
−50
−50
−60
−60
Right to Left
−80
Left to Right
−90
−100
−110
−140
20
Left to Right
−80
−90
−100
−110
−120
−130
Right to Left
−70
Crosstalk − dB
Crosstalk − dB
−70
−120
RL = 8 Ω
VCC = 18 V
100
RL = 8 Ω
VCC = 24 V
−130
1k
−140
20
10k 20k
100
1k
f − Frequency − Hz
10k 20k
f − Frequency − Hz
G013
G014
Figure 22.
Figure 23.
TYPICAL CHARACTERISTICS, SE CONFIGURATION
TOTAL HARMONIC DISTORTION + NOISE (SE)
vs
FREQUENCY
TOTAL HARMONIC DISTORTION + NOISE (SE)
vs
OUTPUT POWER
10
PO = 1 W
RL = 4 Ω
THD+N − Total Harmonic Distortion + Noise − %
THD+N − Total Harmonic Distortion + Noise − %
10
1
VCC = 12 V
0.1
VCC = 24 V
0.01
VCC = 18 V
0.001
20
100
1k
10k 20k
f = 1 kHz
RL = 4 Ω
1
VCC = 12 V
0.1
VCC = 24 V
0.01
VCC = 18 V
0.001
0.01
f − Frequency − Hz
G015
Figure 24.
0.1
1
10
PO − Output Power − W
40
G016
Figure 25.
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s): TAS5716
21
TAS5716
SLOS569 – JANUARY 2009............................................................................................................................................................................................... www.ti.com
TYPICAL CHARACTERISTICS, SE CONFIGURATION (continued)
EFFICIENCY
vs
OUTPUT POWER
SUPPLY CURRENT
vs
TOTAL OUTPUT POWER
2.0
100
RL = 4 Ω
90
VCC = 18 V
80
1.5
VCC = 24 V
VCC = 18 V
ICC − Supply Current − A
Efficiency − %
70
60
VCC = 12 V
50
40
30
VCC = 12 V
1.0
VCC = 24 V
0.5
20
10
RL = 4 Ω
0.0
0
0
5
10
15
20
0
25
5
10
15
20
25
30
PO − Total Output Power − W
PO − Output Power (Per Channel) − W
G017
Figure 26.
35
40
G018
Figure 27.
OUTPUT POWER
vs
SUPPLY VOLTAGE
20
RL = 4 Ω
18
PO − Output Power − W
16
14
12
THD+N = 10%
10
8
THD+N = 1%
6
4
2
0
10
12
14
16
18
20
22
VCC − Supply Voltage − V
24
26
G019
Figure 28.
22
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s): TAS5716
TAS5716
www.ti.com............................................................................................................................................................................................... SLOS569 – JANUARY 2009
DETAILED DESCRIPTION
POWER SUPPLY
The digital portion of the chip requires 3.3 V, and the power stages can work from 10 V to 26 V.
CLOCK, AUTO DETECTION, AND PLL
The TAS5716 DAP is a slave device. It accepts MCLK, SCLK, and LRCLK. The digital audio processor (DAP)
supports all the sample rates and MCLK rates that are defined in the clock control register.
The TAS5716 checks to verify that SCLK is a specific value of 32 fS, 48 fS, or 64 fS. The DAP only supports a 1 ×
fS LRCLK. The timing relationship of these clocks to SDIN1/2 is shown in subsequent sections. The clock section
uses MCLK or the internal oscillator clock (when MCLK is unstable or absent) to produce the internal clock.
The DAP can autodetect and set the internal clock-control logic to the appropriate settings for the frequencies of
32 kHz, normal speed (44.1 or 48 kHz), double speed (88.2 kHz or 96 kHz), and quad speed (176.4 kHz or 192
kHz). The automatic sample rate detection can be disabled and the values set via I2C in the clock control
register.
The DAP also supports an AM interference-avoidance mode during which the clock rate is adjusted, in concert
with the PWM sample rate converter, to produce a PWM output at 7 × fS, 8 × fS, or 6 × fS.
The sample rate must be set manually during AM interference avoidance and when de-emphasis is enabled.
SERIAL DATA INTERFACE
Serial data is input on SDIN1/2. The PWM outputs are derived from SDIN1/2. The TAS5716 DAP accepts 32-,
44.1-, 48-, 88.2-, 96-, 176.4-, and 192-kHz serial data as 16-, 18-, 20-, or 24-bit data in left-justified,
right-justified, or I2S serial-data format.
PWM SECTION
The TAS5716 DAP device uses noise-shaping and sophisticated error correction algorithms to achieve high
power efficiency and high-performance digital audio reproduction. The DAP uses a fourth-order noise shaper that
has >100-dB SNR performance from 20 Hz to 20 kHz. The PWM section accepts 24-bit PCM data from the DAP
and outputs four PWM audio output channels. The TAS5716 PWM section output supports bridge-tied loads.
The PWM section has individual channel dc-blocking filters that can be enabled and disabled. The filter cutoff
frequency is less than 1 Hz. Individual channel de-emphasis filters for 32-, 44.1-, and 48-kHz are included and
can be enabled and disabled.
Finally, the PWM section has an adjustable maximum modulation limit of 93.8% to 99.2%.
I2C COMPATIBLE SERIAL-CONTROL INTERFACE
The TAS5716 DAP has an I2C serial-control slave interface to receive commands from a system controller. The
serial-control interface supports both normal-speed (100-kHz) and high-speed (400-kHz) operations without wait
states. As an added feature, this interface operates even if MCLK is absent.
The serial-control interface supports both single-byte and multiple-byte read and write operations for status
registers and the general control registers associated with the PWM.
The I2C interface supports a special mode which permits I2C write operations to be broken up into multiple
data-write operations that are multiples of 4 data bytes. These are 6-, 10-, 14-, 18-, ... etc., -byte write operations
that are composed of a device address, read/write bit, subaddress, and any multiple of 4 bytes of data. This
permits the system to write large register values incrementally without blocking other I2C transactions.
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s): TAS5716
23
24
Submit Documentation Feedback
Product Folder Link(s): TAS5716
SDIN2
SDIN1
SDI
0x04
SDIN1L
SDIN1R
SDIN2L
SDIN2R
6
4
3
2
1
0x20
R'
Down Mix
0x21<3:0>
L'
SUB
2
BQ
7
BQ
7
BQ
0x21<9:8>
(L'+R')/2
0x21<11>
Bass
Management
RS
LS
RF
LF
0x21<12>
Vol6
0x0D
Vol 4
0x0B
Vol 3
0x0A
Vol 2
0x09
Vol1
0x08
DRC2
drc2_ coeff
Drc2_en
drc1_ coeff
Drc1_en
Drc2_dis
drc1_ coeff
Drc1_en
drc1_ coeff
Drc1_en
DRC1
drc1_ coeff
Drc1_en
Drc1_dis
Noise
Shaper
AD/BD
B
T
L
PWM3
0x13
0x20<14:12>
PWM2
0x12
PWM1
0x11
Sub+
B
T
L
0x20<6:4>
Sub–
B
T
L
PWM6
0x16
PWM5
0x15
PWM4
0x14
0x20<10:8>
RF–
RF+
LF–
LF+
0x20<3>
Noise
Shaper
AD
Noise
Shaper
AD
Noise
Shaper
AD/BD
0x20<19>
Noise
Shaper
AD/BD
0x20<23>
6
6
6
6
6
6
6
6
0x25
B0263-01
HPR
HPL
Sub+
Sub–
Out_D
Out_C
Out_B
Out_A
TAS5716
SLOS569 – JANUARY 2009............................................................................................................................................................................................... www.ti.com
BQ (0x24)
Loudness (0x23)
Master Volume 0x07
Figure 29. TAS5716 DAP Data Flow Diagram With I2C Registers
Copyright © 2009, Texas Instruments Incorporated
TAS5716
www.ti.com............................................................................................................................................................................................... SLOS569 – JANUARY 2009
I2S TIMING
I2S timing uses LRCLK to define when the data being transmitted is for the left channel and when it is for the
right channel. LRCLK is low for the left channel and high for the right channel. A bit clock running at 32, 48, or
64 × fS is used to clock in the data. There is a delay of one bit clock from the time the LRCLK signal changes
state to the first bit of data on the data lines. The data is written MSB-first and is valid on the rising edge of bit
clock. The DAP masks unused trailing data-bit positions.
2
2-Channel I S (Philips Format) Stereo Input
32 Clks
LRCLK (Note Reversed Phase)
32 Clks
Right Channel
Left Channel
SCLK
SCLK
MSB
24-Bit Mode
23 22
LSB
9
8
5
4
5
4
1
0
1
0
1
0
MSB
LSB
23 22
9
8
5
4
19 18
5
4
1
0
15 14
1
0
1
0
20-Bit Mode
19 18
16-Bit Mode
15 14
T0034-01
NOTE: All data presented in 2s-complement form with MSB first.
Figure 30. I2S 64-fS Format
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s): TAS5716
25
TAS5716
SLOS569 – JANUARY 2009............................................................................................................................................................................................... www.ti.com
2
2-Channel I S (Philips Format) Stereo Input/Output (24-Bit Transfer Word Size)
LRCLK
24 Clks
24 Clks
Left Channel
Right Channel
SCLK
SCLK
MSB
24-Bit Mode
23 22
MSB
LSB
17 16
9
8
5
4
13 12
5
4
1
0
9
1
0
3
2
1
0
LSB
23 22
17 16
9
8
5
4
19 18
13 12
5
4
1
0
15 14
9
1
0
3
2
1
20-Bit Mode
19 18
16-Bit Mode
15 14
8
8
T0092-01
NOTE: All data presented in 2s-complement form with MSB first.
Figure 31. I2S 48-fS Format
2
2-Channel I S (Philips Format) Stereo Input
LRCLK
16 Clks
16 Clks
Left Channel
Right Channel
SCLK
SCLK
MSB
16-Bit Mode
15 14 13 12
MSB
LSB
11 10
9
8
5
4
3
2
1
0
15 14 13 12
LSB
11 10
9
8
5
4
3
2
1
T0266-01
NOTE: All data presented in 2s-complement form with MSB first.
Figure 32. I2S 32-fS Format
26
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s): TAS5716
TAS5716
www.ti.com............................................................................................................................................................................................... SLOS569 – JANUARY 2009
LEFT-JUSTIFIED
Left-justified (LJ) timing uses LRCLK to define when the data being transmitted is for the left channel and when it
is for the right channel. LRCLK is high for the left channel and low for the right channel. A bit clock running at 32,
48, or 64 × fS is used to clock in the data. The first bit of data appears on the data lines at the same time LRCLK
toggles. The data is written MSB-first and is valid on the rising edge of the bit clock. The DAP masks unused
trailing data-bit positions.
2-Channel Left-Justified Stereo Input
32 Clks
32 Clks
Left Channel
Right Channel
LRCLK
SCLK
SCLK
MSB
24-Bit Mode
23 22
LSB
9
8
5
4
5
4
1
0
1
0
1
0
MSB
LSB
23 22
9
8
5
4
19 18
5
4
1
0
15 14
1
0
1
0
20-Bit Mode
19 18
16-Bit Mode
15 14
T0034-02
NOTE: All data presented in 2s-complement form with MSB first.
Figure 33. Left-Justified 64-fS Format
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s): TAS5716
27
TAS5716
SLOS569 – JANUARY 2009............................................................................................................................................................................................... www.ti.com
2-Channel Left-Justified Stereo Input (24-Bit Transfer Word Size)
24 Clks
24 Clks
Left Channel
Right Channel
LRCLK
SCLK
SCLK
MSB
24-Bit Mode
23 22
21
LSB
17 16
9
8
5
4
13 12
5
4
1
0
9
1
0
1
0
MSB
LSB
21
17 16
9
8
5
4
19 18 17
13 12
5
4
1
0
15 14 13
9
1
0
23 22
1
0
20-Bit Mode
19 18 17
16-Bit Mode
15 14 13
8
8
T0092-02
NOTE: All data presented in 2s-complement form with MSB first.
Figure 34. Left-Justified 48-fS Format
2-Channel Left-Justified Stereo Input
16 Clks
16 Clks
Left Channel
Right Channel
LRCLK
SCLK
SCLK
MSB
16-Bit Mode
15 14 13 12
LSB
11 10
9
8
5
4
3
2
1
0
MSB
15 14 13 12
LSB
11 10
9
8
5
4
3
2
1
0
T0266-02
NOTE: All data presented in 2s-complement form with MSB first.
Figure 35. Left-Justified 32-fS Format
28
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s): TAS5716
TAS5716
www.ti.com............................................................................................................................................................................................... SLOS569 – JANUARY 2009
RIGHT-JUSTIFIED
Right-justified (RJ) timing uses LRCLK to define when the data being transmitted is for the left channel and when
it is for the right channel. LRCLK is high for the left channel and low for the right channel. A bit clock running at
32, 48, or 64 × fS is used to clock in the data. The first bit of data appears on the data lines 8 bit-clock periods
(for 24-bit data) after LRCLK toggles. In RJ mode, the LSB of data is always clocked by the last bit clock before
LRCLK transitions. The data is written MSB-first and is valid on the rising edge of the bit clock. The DAP masks
unused leading data-bit positions.
2-Channel Right-Justified (Sony Format) Stereo Input
32 Clks
32 Clks
Left Channel
Right Channel
LRCLK
SCLK
SCLK
MSB
24-Bit Mode
LSB
23 22
19 18
15 14
1
0
19 18
15 14
1
0
15 14
1
0
MSB
LSB
23 22
19 18
15 14
1
0
19 18
15 14
1
0
15 14
1
0
20-Bit Mode
16-Bit Mode
T0034-03
Figure 36. Right-Justified 64-fS Format
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s): TAS5716
29
TAS5716
SLOS569 – JANUARY 2009............................................................................................................................................................................................... www.ti.com
2-Channel Right-Justified Stereo Input (24-Bit Transfer Word Size)
24 Clks
24 Clks
Left Channel
Right Channel
LRCLK
SCLK
SCLK
MSB
24-Bit Mode
23 22
LSB
19 18
15 14
6
5
2
1
0
19 18
15 14
6
5
2
1
0
15 14
6
5
2
1
0
MSB
23 22
LSB
19 18
15 14
6
5
2
1
0
19 18
15 14
6
5
2
1
0
15 14
6
5
2
1
0
20-Bit Mode
16-Bit Mode
T0092-03
Figure 37. Right-Justified 48-fS Format
Figure 38. Right-Justified 32-fS Format
30
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s): TAS5716
TAS5716
www.ti.com............................................................................................................................................................................................... SLOS569 – JANUARY 2009
I2C SERIAL CONTROL INTERFACE
The TAS5716 DAP has a bidirectional I2C interface that compatible with the I2C (Inter IC) bus protocol and
supports both 100-kHz and 400-kHz data transfer rates for single- and multiple-byte write and read operations.
This is a slave-only device that does not support a multimaster bus environment or wait-state insertion. The
control interface is used to program the registers of the device and to read device status.
The DAP supports the standard-mode I2C bus operation (100 kHz maximum) and the fast I2C bus operation
(400 kHz maximum). The DAP performs all I2C operations without I2C wait cycles.
General I2C Operation
The I2C bus employs two signals; SDA (data) and SCL (clock), to communicate between integrated circuits in a
system. Data is transferred on the bus serially, one bit at a time. The address and data can be transferred in byte
(8-bit) format, with the most-significant bit (MSB) transferred first. In addition, each byte transferred on the bus is
acknowledged by the receiving device with an acknowledge bit. Each transfer operation begins with the master
device driving a start condition on the bus and ends with the master device driving a stop condition on the bus.
The bus uses transitions on the data terminal (SDA) while the clock is high to indicate start and stop conditions.
A high-to-low transition on SDA indicates a start, and a low-to-high transition indicates a stop. Normal data-bit
transitions must occur within the low time of the clock period. These conditions are shown in Figure 39. The
master generates the 7-bit slave address and the read/write (R/W) bit to open communication with another
device and then waits for an acknowledge condition. The TAS5716 holds SDA low during the acknowledge clock
period to indicate an acknowledgment. When this occurs, the master transmits the next byte of the sequence.
Each device is addressed by a unique 7-bit slave address plus R/W bit (1 byte). All compatible devices share the
same signals via a bidirectional bus using a wired-AND connection. An external pullup resistor must be used for
the SDA and SCL signals to set the high level for the bus.
SDA
R/
A
W
7-Bit Slave Address
7
6
5
4
3
2
1
0
8-Bit Register Address (N)
7
6
5
4
3
2
1
0
8-Bit Register Data For
Address (N)
A
7
6
5
4
3
2
1
8-Bit Register Data For
Address (N)
A
0
7
6
5
4
3
2
1
A
0
SCL
Start
Stop
T0035-01
2
Figure 39. Typical I C Sequence
There is no limit on the number of bytes that can be transmitted between start and stop conditions. When the last
word transfers, the master generates a stop condition to release the bus. A generic data-transfer sequence is
shown in Figure 39.
The 7-bit address for the TAS5716 is 0011 011 (0x36).
Single- and Multiple-Byte Transfers
The serial-control interface supports both single-byte and multiple-byte read/write operations for status registers
and the general control registers associated with the PWM. However, for the DAP data processing registers, the
serial-control interface supports only multiple-byte (4-byte) read/write operations.
During multiple-byte read operations, the DAP responds with data, a byte at a time, starting at the subaddress
assigned, as long as the master device continues to respond with acknowledges. If a particular subaddress does
not contain 32 bits, the unused bits are read as logic 0.
During multiple-byte write operations, the DAP compares the number of bytes transmitted to the number of bytes
that are required for each specific subaddress. If a write command is received for a biquad subaddress, the DAP
expects to receive five 32-bit words. If fewer than five 32-bit data words have been received when a stop
command (or another start command) is received, the data received is discarded. Similarly, if a write command is
received for a mixer coefficient, the DAP expects to receive one 32-bit word.
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s): TAS5716
31
TAS5716
SLOS569 – JANUARY 2009............................................................................................................................................................................................... www.ti.com
Supplying a subaddress for each subaddress transaction is referred to as random I2C addressing. The TAS5716
also supports sequential I2C addressing. For write transactions, if a subaddress is issued followed by data for
that subaddress and the 15 subaddresses that follow, a sequential I2C write transaction has taken place, and the
data for all 16 subaddresses is successfully received by the TAS5716. For I2C sequential write transactions, the
subaddress then serves as the start address, and the amount of data subsequently transmitted, before a stop or
start is transmitted, determines how many subaddresses are written. As was true for random addressing,
sequential addressing requires that a complete set of data be transmitted. If only a partial set of data is written to
the last subaddress, the data for the last subaddress is discarded. However, all other data written is accepted;
only the incomplete data is discarded.
Single-Byte Write
As shown in Figure 40, a single-byte data-write transfer begins with the master device transmitting a start
condition followed by the I2C device address and the read/write bit. The read/write bit determines the direction of
the data transfer. For a write-data transfer, the read/write bit is 0. After receiving the correct I2C device address
and the read/write bit, the DAP responds with an acknowledge bit. Next, the master transmits the address byte or
bytes corresponding to the TAS5716 internal memory address being accessed. After receiving the address byte,
the TAS5716 again responds with an acknowledge bit. Next, the master device transmits the data byte to be
written to the memory address being accessed. After receiving the data byte, the TAS5716 again responds with
an acknowledge bit. Finally, the master device transmits a stop condition to complete the single-byte data-write
transfer.
Start
Condition
Acknowledge
A6
A5
A4
A3
A2
A1
A0
Acknowledge
R/W ACK A7
A6
A5
2
A4
A3
A2
A1
Acknowledge
A0 ACK D7
D6
Subaddress
I C Device Address and
Read/Write Bit
D5
D4
D3
D2
D1
D0 ACK
Stop
Condition
Data Byte
T0036-01
Figure 40. Single-Byte Write Transfer
Multiple-Byte Write
A multiple-byte data-write transfer is identical to a single-byte data-write transfer except that multiple data bytes
are transmitted by the master device to the DAP as shown in Figure 41. After receiving each data byte, the
TAS5716 responds with an acknowledge bit.
Start
Condition
Acknowledge
A6
A5
A1
A0 R/W ACK A7
2
I C Device Address and
Read/Write Bit
A6
A5
A4
A3
Subaddress
A1
Acknowledge
Acknowledge
Acknowledge
Acknowledge
A0 ACK D7
D0 ACK D7
D0 ACK D7
D0 ACK
First Data Byte
Other Data Bytes
Last Data Byte
Stop
Condition
T0036-02
Figure 41. Multiple-Byte Write Transfer
32
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s): TAS5716
TAS5716
www.ti.com............................................................................................................................................................................................... SLOS569 – JANUARY 2009
Single-Byte Read
As shown in Figure 42, a single-byte data-read transfer begins with the master device transmitting a start
condition followed by the I2C device address and the read/write bit. For the data-read transfer, both a write
followed by a read are actually done. Initially, a write is done to transfer the address byte or bytes of the internal
memory address to be read. As a result, the read/write bit becomes a 0. After receiving the TAS5716 address
and the read/write bit, TAS5716 responds with an acknowledge bit. In addition, after sending the internal memory
address byte or bytes, the master device transmits another start condition followed by the TAS5716 address and
the read/write bit again. This time the read/write bit becomes a 1, indicating a read transfer. After receiving the
address and the read/write bit, the TAS5716 again responds with an acknowledge bit. Next, the TAS5716
transmits the data byte from the memory address being read. After receiving the data byte, the master device
transmits a not-acknowledge followed by a stop condition to complete the single-byte data-read transfer.
Repeat Start
Condition
Start
Condition
Acknowledge
A6
A5
A1
A0 R/W ACK A7
Acknowledge
A6
2
A5
A4
A0 ACK
A6
A5
A1
A0 R/W ACK D7
D6
2
Subaddress
I C Device Address and
Read/Write Bit
Not
Acknowledge
Acknowledge
D1
D0 ACK
Stop
Condition
Data Byte
I C Device Address and
Read/Write Bit
T0036-03
Figure 42. Single-Byte Read Transfer
Multiple-Byte Read
A multiple-byte data read transfer is identical to a single-byte data-read transfer except that multiple data bytes
are transmitted by the TAS5716 to the master device as shown in Figure 43. Except for the last data byte, the
master device responds with an acknowledge bit after receiving each data byte.
Repeat Start
Condition
Start
Condition
Acknowledge
A6
2
A0 R/W ACK A7
I C Device Address and
Read/Write Bit
Acknowledge
A6
A5
Subaddress
A6
A0 ACK
2
Acknowledge
Acknowledge
Acknowledge
Not
Acknowledge
A0 R/W ACK D7
D0 ACK D7
D0 ACK D7
D0 ACK
I C Device Address and
Read/Write Bit
First Data Byte
Other Data Bytes
Last Data Byte
Stop
Condition
T0036-04
Figure 43. Multiple-Byte Read Transfer
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s): TAS5716
33
TAS5716
SLOS569 – JANUARY 2009............................................................................................................................................................................................... www.ti.com
Dynamic Range Control (DRC)
The DRC scheme has a single threshold, offset, and slope (all programmable). There is one ganged DRC for the
left/right channels and one DRC for the subwoofer channel.
DRC-Compensated Output
The DRC input/output diagram is shown in Figure 44.
k
1:1 Transfer Function
Implemented Transfer Function
T
DRC Input Level
M0091-01
Professional-quality dynamic range compression automatically adjusts volume to flatten volume level.
• One DRC for left/right and one DRC for subwoofer
• Each DRC has adjustable threshold, offset, and compression levels
• Programmable energy, attack, and decay time constants
• Transparent compression: compressors can attack fast enough to avoid apparent clipping before engaging,
and decay times can be set slow enough to avoid pumping.
Figure 44. Dynamic Range Control
Energy
Filter
Compression
Control
Attack
and
Decay
Filters
a, w
T, K, O
aa, wa / ad, wd
DRC1
0x3A
0x40, 0x41, 0x42
0x3B / 0x3C
DRC2
0x3D
0x43, 0x44, 0x45
0x3E / 0x3F
Audio Input
DRC Coefficient
Alpha Filter Structure
S
a
w
–1
Z
NOTE:
a=a
w=1–a
B0265-01
Figure 45. DRC Structure
34
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s): TAS5716
TAS5716
www.ti.com............................................................................................................................................................................................... SLOS569 – JANUARY 2009
Loudness Function
The TAS5716 provides a direct form-I biquad for loudness on the subwoofer channel. The first biquad is
contained in a gain-compensation circuit that maintains the overall system gain at 1 or less to prevent clipping at
loud volume settings. This gain compensation is shown in Figure 46
1 if Vol £ 1/G
0 if Vol ³ 1/G + 1/Scale
1 - Scale (Vol - 1/G) otherwise
From
Input
Mux
To
Output
Mux
Loudness
Biquad (0x23)
Gain = G
Volume
Scale = 1/(1 - 1/G)
Biquad (0x24)
0 if Vol £ 1/G
1 if Vol ³ 1/G + 1/Scale
Scale (Vol - 1/G) otherwise
B0273-01
Figure 46. Biquad Gain-Control Structure
Table 1. Loudness Table Example for Gain = 4, 1/G = 0.25, Scale = 1.33
Volume
0.125
0.25
0.375
0.5
0.625
0.75
0.875
1
1.125
1.25
1.375
1.5
1.625
1.75
1.875
2
Biquad path
1
1
0.833
0.666
0.5
0.333
0.166
0
0
0
0
0
0
0
0
0
Direct path
0
0
0.166
0.333
0.5
0.666
0.833
1
1
1
1
1
1
1
1
1
Total gain
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
The biquads are implemented in a direct form-I architecture. The direct form-I structure provides a separate delay
element and mixer (gain coefficient) for each node in the biquad filter.
The five 26-bit (3.23) coefficients for the biquad are programmable via the I2C interface.
The following steps are involved in using a loudness biquad with the volume compensation feature:
1. Program the biquad with a loudness filter.
2. Program 0x26 (1/G) and 0x28 (scale).
3. Enable volume compensation in register 0x0E.
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s): TAS5716
35
TAS5716
SLOS569 – JANUARY 2009............................................................................................................................................................................................... www.ti.com
b0
x(n)
S
b1
z
a1
–1
z
b2
z
y(n)
Magnitude
Truncation
–1
a2
–1
z
–1
M0012-02
Figure 47. Biquad Filter
BANK SWITCHING
The TAS5716 uses an approach called bank switching together with automatic sample-rate detection. All
processing features that must be changed for different sample rates are stored internally in the TAS5716. The
TAS5716 has three full banks storing information, one for 32 kHz, one for 44.1/48 kHz, and one for all other data
rates. Combined with the clock-rate autodetection feature, bank switching allows the TAS5716 to detect
automatically a change in the input sample rate and switch to the appropriate bank without any MCU
intervention.
The TAS5716 supports three banks of coefficients to be updated during the initialization. One bank is for 32 kHz,
a second bank is for 44.1/48 kHz, and a third bank is for all other sample rates. An external controller updates
the three banks (see the I2C register mapping table for bankable locations) during the initialization sequence.
If the autobank switch is enabled (register 0x50, bits 2:0), then the TAS5716 automatically swaps the coefficients
for subsequent sample rate changes, avoiding the need for any external controller intervention for a sample rate
change.
By default, bits 2:0 have the value 000; that means the bank switch is disabled. In that state, any update to
locations 0x29–0x3F goes into the DAP. A write to register 0x50 with bits 2:0 being 001, 010, or 011 brings the
system into the coefficient-bank-update state update bank1, update bank2, or update bank3, respectively. Any
subsequent write to locations 0x29–0x3F updates the coefficient banks stored outside the DAP. After updating all
the three banks, the system controller should issue a write to register 0x50 with bits 2:0 being 100; this changes
the system state to automatic bank update. In automatic bank update, the TAS5716 automatically swaps banks
based on the sample rate.
In the headphone mode, speaker equalization and DRC are disabled, and they are restored on returning to the
speaker mode.
Command sequences for initialization can be summarized as follows:
1. Enable factory trim for internal oscillator: Write to register 0x1B with a value 0x00.
2. Update coefficients: Coefficients can be loaded into DAP RAM using the manual bank mode.
OR
Use automatic bank mode.
a. Enable bank-1 mode: Write to register 0x50 with 0x01. Load the 32-kHz coefficients. TI ALE
can generate coefficients.
b. Enable bank-2 mode: Write to register 0x50 with 0x02. Load the 48-kHz coefficients.
c. Enable bank-3 mode: Write to register 0x50 with 0x03. Load the other coefficients.
d. Enable automatic bank switching by writing to register 0x50 with 0x04.
3. Bring the system out of all-channel shutdown: Write 0 to bit 6 of register 0x05.
4. Issue master volume: Write to register 0x07 with the volume value (0 db = 0x30).
36
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s): TAS5716
TAS5716
www.ti.com............................................................................................................................................................................................... SLOS569 – JANUARY 2009
APPLICATION INFORMATION
Recovery From Error
Protection Mechanisms in the TAS5716
• SCP (short-circuit protection, OCP) protects against shorts across the load, to GND, and to PVCC.
• OTP turns off the device if Tdie (typical) > 150°C.
• UVP turns off the device if PVCC (typical) < 8.4 V
• OVP turns off the device if PVCC (typical) > 27.5 V
A short-circuit condition can be detected also by an external controller. The SCP error from the external power
stage is also fed into TAS5716. The VALID pin goes low in the event of a short circuit. The VALID pin can be
monitored by an external microcontroller. The TAS5716 initiates a back-end error sequence by itself to recover
from the error, which involves settling VALID low for a programmable amount of time and then retrying to check
whether the SCP condition still exists.
• OTP turns the device back on when Tdie (typical) < 135°C.
• UVP turns the device back on if PVCC (typical) is > 8.5 V.
• OVP turns the device back on if PVCC (typical) is < 27.2 V.
Interchannel Delay (ICD) Settings
Recommended ICD Settings
Mode
Description
ICD1
ICD2
ICD3
ICD4
ICD5
ICD6
2.0 ch BD BTL
2 BTL channels, internal
power stage only, BD
mode
A(L+) = 19
(0x4C)
C(R+) = 13
(0x34)
B(L–) = 7
(0x1C)
D(R–) = 25
(0x64)
SM(S–) = –12 SP(S+) = –28
(0xD0)
(0x90)
2.1 ch AD BTL
2 internal BTL channels,
1 external BTL channel
using PBTL TAS5601,
AD mode
A(L+) = 23
(0x5C)
C(R+) = 9
(0x24)
B(L–) = 21
(0x54)
D(R–) = 11
(0x2C)
SM(S–) = –23 SP(S+) = –21
(0xA4)
(0xAC)
2.1 ch AD SE
2 internal SE channels (2 A(L+) = 15
unused), 1 external BTL (0x3C)
channel using PBTL
TAS5601, AD mode
B(R–) = –15
(0xC4)
B(0) = 0
(0x00)
D(0) = 0
(0x00)
SM(S–) = –30 SP(S+) = –32
(0x88)
(0x80)
2.1 ch BD BTL
2 internal BTL channels,
1 external BTL channel
using PBTL TAS5601,
BD mode
A(L+) = 19
(0x4C)
C(R+) = 13
(0x34)
B(L–) = 7
(0x1C)
D(R–) = 25
(0x64 )
SM(S–) = –12 SP(S+) = –28
(0xD0)
(0x90)
3.0 ch AD 2SE + 2 internal SE channels +
1 BTL
1 internal BTL channel,
AD mode
A(L+) = 15
(0x3C)
B(R–) = –16
(0xC0)
SM(0) = 0
(0x00)
SP(0) = 0
(0x00)
D(S–) = 0
(0x00)
C(S+) = 2
(0x08)
4.0 ch AD SE
4 internal SE channels
A(L1+) = 8
(=0x20)
B(R1–) = –24
(0xA0)
C(L2+) = –8
(0xE0)
D(R2–) = 24
(0x60)
SM(0) = 1
(0x04)
SP(0) = –1
(0xFC)
4.1 ch AD SE
4 internal SE channels +
1 external BTL channel,
using PBTL TAS5601,
AD mode.
A(L1+) = 8
(0x20)
B(R1–) = –24
(0xA0)
C(L2+) = –8
(xE0)
D(R2–)= 24
(0x60)
SM(S–) = 1
(0x04)
SP(S+) = –1
(0xFC)
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s): TAS5716
37
TAS5716
SLOS569 – JANUARY 2009............................................................................................................................................................................................... www.ti.com
Calculation of Output Signal Level of TAS5716 Feedback Power Stage
(Gain Is Independent of PVCC)
The gain of the TAS5716 is the total digital gain of the controller multiplied by the gain of the power stage.
For a half-bridge channel of the TAS5716 power stage, the gain is simply:
Power stage gain = 13 × VRMS / modulation level
Modulation level = fraction of full-scale modulation of the PWM signal at the input of the power stage
VRMS = Audio voltage level at the output of the power stage = 13 × modulation level
For the TAS5716 controller, the gain is the programmed digital gain multiplied by a scaling factor, called the
maximum modulation level. The maximum modulation level is derived from the modulation limit programmed in
the controller, which limits duty cycle to a set number of percent above 0% and below 100%. Setting the
modulation limit to 97.7% (default) limits the duty cycle between 2.3% and 97.7%.
Controller gain = digital gain × maximum modulation level × (modulation level/digital FFS)
Digital FFS = digital input fraction of full scale
Modulation limit = 97.7%
Maximum modulation level = 2 × modulation limit – 1 = 0.954
The output signal level of the TAS5716 can now be calculated.
VRMS = digital FFS × digital gain × maximum modulation level × 13
With the modulation limit set at the default level of 97.7%, this becomes:
VRMS = digital FFS × digital gain × 12.4
(Single-ended)
VRMS = digital FFS × digital gain × 24.8
(BTL)
Example: Input = –20 dbFS; volume = 0 dB; biquads = ALL PASS; modulation index = 97.7%; mode = BTL
Output VRMS = 24.8 × 0.1 × 1 = 2.48 V
I2C SERIAL-CONTROL COMMAND CHARACTERISTICS
The DAP has two groups of I2C commands. One set is commands that are designed specifically to be operated
while audio is streaming and that have built-in mechanisms to prevent noise, clicks, and pops. The other set
does not have this built-in protection.
Commands that are designed to be adjusted while audio is streaming:
• Master volume
• Master mute
• Individual channel volume
• Individual channel mute
Commands that are normally issued as part of initialization:
• Serial-data interface format
• De-emphasis
• Sample-rate conversion
• Input multiplexer
• Output multiplexer
• Biquads
• Channel-6 multiplexer-2
• Channel delay
• Enable/disable dc blocking
• Hard/soft unmute from clock error
• Enable/disable headphone outputs
Start-up sequence for correct device operation
This sequence must be followed to ensure proper operation.
38
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s): TAS5716
TAS5716
www.ti.com............................................................................................................................................................................................... SLOS569 – JANUARY 2009
1.
2.
3.
4.
5.
6.
7.
Hold ALL logic inputs low. Power up AVDD/DVDD and wait for the inputs to settle in the allowed range.
Drive PDN = 1, MUTE = 1, and drive other logic inputs to the desired state.
Provide a stable MCLK, LRCLK, and SCLK (clock errors must be avoided during the initialization sequence) .
After completing step 3, wait 100 µs, then drive RESET = 1, and wait 13.5 ms after RESET goes high.
Trim the internal oscillator (write 0x00 to register 0x1B).
Wait 50 ms while the part acquires lock.
Configure the DAP via I2C, e.g.:
– Downmix control (0x21)
– Biquads (0x23–0x24 and 0x29–0x38)
– DRC parameters and controls (0x3A–0x46)
– Bank select (0x50)
NOTE: User may not issue any I2C reads or writes to the above registers after this step is complete.
8. Configure remaining I2C registers, e.g.:
– Shutdown group
– De-emphasis
– Input multiplexers
– Output multiplexers
– Channel delays
– DC blocking
– Hard/soft unmute from clock error
– Serial data interface format
– Clock register (manual clock mode only)
NOTE: The BKND_ERR register (0x1C) can only be written once with a value that is not reserved (00
and 01 are reserved values).
9. Exit all-channel shutdown (write 0 to bit 6 of register 0x05).
10. This completes the initialization sequence. From this step on, no further constraints are imposed on PDN,
MUTE, and clocks.
11. During normal operation the user may do the following:
a. Write to the master or individual-channel volume registers.
b. Write to the soft-mute register.
c. Write to the clock and serial-data interface-format registers (in manual clock mode only).
d. Write to bit 6 of register 0x05 to enter/exit all-channel shutdown. No other bits of register 0x05 may be
altered. After issuing the all-channel shutdown command, no further I2C transactions that address this
device are allowed for a period of at least: 1 ms + 1.3 × (period specified in start/stop register 0x1A) .
e. PDN may be asserted (low) at any time. Once PDN is asserted, no I2C transactions that address this
device may be issued until PDN has been deasserted and the part has returned to active mode.
NOTE: When the device is in a power-down state (initiated via PDN), the part is not reset if RESET is
asserted.
NOTE: Once RESET is asserted, and as long as the part is in a reset state, the part does not power
down if PDN is asserted. For powering the part down, a negative edge on PDN must be issued when
RESET is high and the part is not in a reset state.
NOTE: No registers besides those explicitly listed in Steps a.–d. should be altered during normal
operation (i.e., after exiting all-channel shutdown).
NOTE: No registers should be read during normal operation (i.e., after exiting all-channel shutdown) .
12. To reconfigure registers:
a. Return to all-channel shutdown (observe the shutdown wait time as specified in Step 11.d.).
b. Drive PDN = 1, and hold MUTE stable.
c. Provide a stable MCLK, LRCLK, and SCLK.
d. Repeat configuration starting from step (6).
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s): TAS5716
39
TAS5716
SLOS569 – JANUARY 2009............................................................................................................................................................................................... www.ti.com
Writing of Input Mixers
Writing of input mixers must follow the guidelines on updating DAP coefficients.
The sequence for writing of input mixers, which are internal coefficients, is as follows:
1. Enable input mixer write. Write to register 0xF8: A5 A5 A5 A5 {4 bytes}.
2. Write to input mixer address register 0xF9: 00 00 00 ADDR {4 bytes} (where ADDR = 0x96, 0x99, 0xAA, or
0xA9).
3. Write the mixer value (3.23 format) to 0xFA: {zeros[37:0], mixer_value[25:0]} {total 8 bytes}.
The MSBs (38 bits) are zeros and LSBs (26 bits) comprise the mixer value in 3.23 format.
Sample Calculation for 3.23 Format
db
Linear
Decimal
0
1
8,388,608
Hex (3.23 Format)
0080 0000
5
1.7782794
14,917,288
00E3 9EA8
–5
0.5623413
4,717,260
0047 FACC
X
L = 10(X/20)
D = 8,388,608 × L
H = dec2hex (D, 8)
Table 2. Serial Control Interface Register Summary (1)
SUBADDRESS
REGISTER NAME
NO. OF
BYTES
INITIALIZATION
VALUE
CONTENTS
A u indicates unused bits.
0x00
Clock control register
1
Description shown in subsequent section
0x6C
0x01
Device ID register
1
Description shown in subsequent section
0x28
0x02
Error status register
1
Description shown in subsequent section
0x00
0x03
System control register 1
1
Description shown in subsequent section
0xA0
0x04
Serial-data interface
register
1
Description shown in subsequent section
0x05
0x05
System-control register 2
1
Description shown in subsequent section
0x40
0x06
Soft-mute register
1
Description shown in subsequent section
0x00
0x07
Master volume
1
Description shown in subsequent section
0xFF (mute)
0x08
Channel 1 vol
1
Description shown in subsequent section
0x30 (0 dB)
0x09
Channel 2 vol
1
Description shown in subsequent section
0x30 (0 dB)
0x0A
Channel 3 vol
1
Description shown in subsequent section
0x30 (0 dB)
0x0B
Channel 4 vol
1
Description shown in subsequent section
0x30 (0 dB)
0x0C
HP volume
1
Description shown in subsequent section
0x30 (0 dB)
0x0D
Channel-6 vol
1
Description shown in subsequent section
0x30 (0 dB)
0x0E
Volume configuration
register
1
Description shown in subsequent section
0x91
1
Reserved (2)
0x0F
0x10
Modulation-limit register
1
Description shown in subsequent section
0x02
0x11
IC delay channel 1
1
Description shown in subsequent section
0x4C
0x12
IC delay channel 2
1
Description shown in subsequent section
0x34
0x13
IC delay channel 3
1
Description shown in subsequent section
0x1C
0x14
IC delay channel 4
1
Description shown in subsequent section
0x64
0x15
IC delay channel 5
1
Description shown in subsequent section
0xB0
0x16
IC delay channel 6
1
Description shown in subsequent section
0x90
0x17
Offset register
1
Reserved
0x00
0x18
(1)
(2)
Biquad definition is given in Figure 47.
Reserved registers should not be accessed.
40
Submit Documentation Feedback
1
Reserved
(2)
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s): TAS5716
TAS5716
www.ti.com............................................................................................................................................................................................... SLOS569 – JANUARY 2009
Table 2. Serial Control Interface Register Summary (continued)
SUBADDRESS
REGISTER NAME
NO. OF
BYTES
0x19
PWM shutdown group
register
1
0x30
0x1A
Start/stop period register
1
0x0A
0x1B
Oscillator trim register
1
0x82
0x1C
BKND_ERR register
1
0x02
Reserved (2)
0x1D–0x1F
0x20
Input MUX register
4
Description shown in subsequent section
0x0089 777A
0x21
Ch-6 input mux-2 register
4
Description shown in subsequent section
0x0000 4203
0x22
AM tuned frequency
4
Description shown in subsequent section
0x0000 0000
0x23
ch6_bq[2] (loudness BQ)
20
u[31:26], b0[25:0]
0x0080 0000
u[31:26], b1[25:0]
0x0000 0000
u[31:26], b2[25:0]
0x0000 0000
u[31:26], a1[25:0]
0x0000 0000
u[31:26], a2[25:0]
0x0000 0000
u[31:26], b0[25:0]
0x0080 0000
u[31:26], b1[25:0]
0x0000 0000
u[31:26], b2[25:0]
0x0000 0000
u[31:26], a1[25:0]
0x0000 0000
u[31:26], a2[25:0]
0x0000 0000
0x24
ch6_bq[3] (post volume
BQ)
0x25
PWM MUX register
0x26
1/G register
0x27
20
Description shown in subsequent section
0x0102 1345
4
u[31:26], x[25:0]
0x0080 0000
1
Reserved (3)
0x28
Scale register
4
u[31:26], x[25:0]
0x0080 0000
0x29
ch1_bq[0]
20
u[31:26], b0[25:0]
0x0080 0000
u[31:26], b1[25:0]
0x0000 0000
u[31:26], b2[25:0]
0x0000 0000
u[31:26], a1[25:0]
0x0000 0000
u[31:26], a2[25:0]
0x0000 0000
u[31:26], b0[25:0]
0x0080 0000
u[31:26], b1[25:0]
0x0000 0000
u[31:26], b2[25:0]
0x0000 0000
u[31:26], a1[25:0]
0x0000 0000
u[31:26], a2[25:0]
0x0000 0000
u[31:26], b0[25:0]
0x0080 0000
u[31:26], b1[25:0]
0x0000 0000
u[31:26], b2[25:0]
0x0000 0000
u[31:26], a1[25:0]
0x0000 0000
u[31:26], a2[25:0]
0x0000 0000
u[31:26], b0[25:0]
0x0080 0000
u[31:26], b1[25:0]
0x0000 0000
u[31:26], b2[25:0]
0x0000 0000
u[31:26], a1[25:0]
0x0000 0000
u[31:26], a2[25:0]
0x0000 0000
0x2A
0x2B
0x2C
(3)
INITIALIZATION
VALUE
CONTENTS
ch1_bq[1]
ch1_bq[2]
ch1_bq[3]
20
20
20
Reserved registers should not be accessed.
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s): TAS5716
41
TAS5716
SLOS569 – JANUARY 2009............................................................................................................................................................................................... www.ti.com
Table 2. Serial Control Interface Register Summary (continued)
SUBADDRESS
0x2D
0x2E
0x2F
0x30
0x31
0x32
0x33
0x34
0x35
42
REGISTER NAME
ch1_bq[4]
ch1_bq[5]
ch1_bq[6]
ch2_bq[0]
ch2_bq[1]
ch2_bq[2]
ch2_bq[3]
ch2_bq[4]
ch2_bq[5]
NO. OF
BYTES
20
20
20
20
20
20
20
20
20
CONTENTS
INITIALIZATION
VALUE
u[31:26], b0[25:0]
0x0080 0000
u[31:26], b1[25:0]
0x0000 0000
u[31:26], b2[25:0]
0x0000 0000
u[31:26], a1[25:0]
0x0000 0000
u[31:26], a2[25:0]
0x0000 0000
u[31:26], b0[25:0]
0x0080 0000
u[31:26], b1[25:0]
0x0000 0000
u[31:26], b2[25:0]
0x0000 0000
u[31:26], a1[25:0]
0x0000 0000
u[31:26], a2[25:0]
0x0000 0000
u[31:26], b0[25:0]
0x0080 0000
u[31:26], b1[25:0]
0x0000 0000
u[31:26], b2[25:0]
0x0000 0000
u[31:26], a1[25:0]
0x0000 0000
u[31:26], a2[25:0]
0x0000 0000
u[31:26], b0[25:0]
0x0080 0000
u[31:26], b1[25:0]
0x0000 0000
u[31:26], b2[25:0]
0x0000 0000
u[31:26], a1[25:0]
0x0000 0000
u[31:26], a2[25:0]
0x0000 0000
u[31:26], b0[25:0]
0x0080 0000
u[31:26], b1[25:0]
0x0000 0000
u[31:26], b2[25:0]
0x0000 0000
u[31:26], a1[25:0]
0x0000 0000
u[31:26], a2[25:0]
0x0000 0000
u[31:26], b0[25:0]
0x0080 0000
u[31:26], b1[25:0]
0x0000 0000
u[31:26], b2[25:0]
0x0000 0000
u[31:26], a1[25:0]
0x0000 0000
u[31:26], a2[25:0]
0x0000 0000
u[31:26], b0[25:0]
0x0080 0000
u[31:26], b1[25:0]
0x0000 0000
u[31:26], b2[25:0]
0x0000 0000
u[31:26], a1[25:0]
0x0000 0000
u[31:26], a2[25:0]
0x0000 0000
u[31:26], b0[25:0]
0x0080 0000
u[31:26], b1[25:0]
0x0000 0000
u[31:26], b2[25:0]
0x0000 0000
u[31:26], a1[25:0]
0x0000 0000
u[31:26], a2[25:0]
0x0000 0000
u[31:26], b0[25:0]
0x0080 0000
u[31:26], b1[25:0]
0x0000 0000
u[31:26], b2[25:0]
0x0000 0000
u[31:26], a1[25:0]
0x0000 0000
u[31:26], a2[25:0]
0x0000 0000
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s): TAS5716
TAS5716
www.ti.com............................................................................................................................................................................................... SLOS569 – JANUARY 2009
Table 2. Serial Control Interface Register Summary (continued)
SUBADDRESS
0x36
0x37
0x38
REGISTER NAME
ch2_bq[6]
ch6_bq[0]
ch6_bq[1]
0x39
0x3A
DRC1 ae
NO. OF
BYTES
20
20
20
DRC1 aa
DRC1 ad
DRC2 ae
DRC2 aa
DRC2 ad
0x0000 0000
u[31:26], a1[25:0]
0x0000 0000
u[31:26], a2[25:0]
0x0000 0000
u[31:26], b0[25:0]
0x0080 0000
u[31:26], b1[25:0]
0x0000 0000
u[31:26], b2[25:0]
0x0000 0000
u[31:26], a1[25:0]
0x0000 0000
u[31:26], a2[25:0]
0x0000 0000
u[31:26], b0[25:0]
0x0080 0000
u[31:26], b1[25:0]
0x0000 0000
u[31:26], b2[25:0]
0x0000 0000
u[31:26], a1[25:0]
0x0000 0000
u[31:26], a2[25:0]
0x0000 0000
(4)
0x0080 0000
0x0000 0000
u[31:26], aa[25:0]
0x0080 0000
u[31:26], (1 – aa)[25:0]
0x0000 0000
u[31:26], ad[25:0]
0x0080 0000
u[31:26], (1 – ad)[25:0]
0x0000 0000
u[31:26], ae[25:0]
0x0080 0000
u[31:26], (1 – ae)[25:0]
0x0000 0000
u[31:26], aa[25:0]
0x0080 0000
u[31:26], (1 – aa)[25:0]
0x0000 0000
u[31:26], ad[25:0]
0x0080 0000
8
8
8
8
8
DRC2 (1 – ad)
u[31:26], (1 – ad)[27::0]
0x0000 0000
0x40
DRC1-T
4
T1[31:0]
0xFDA2 1490
0x41
DRC1-K
4
u[31:26], k1[25:0]
0x0384 2109
0x42
DRC1-O
4
u[31:24], O[23:16], O1[15:0]
0x0008 4210
0x43
DRC2-T
4
T2[31:0]
0xFDA2 1490
0x44
DRC2-K
4
u[31:24], k2'[22:0]
0x0384 2109
0x45
DRC2-O
4
u[31:24], O2[25:0]
0x0008 4210
0x46
DRC control
4
u[31:2], ch6[1], ch1_5[0]
0x0000 0000
(4)
0x47–0x49
4
Reserved
0x50
4
Bank update command register
0x0000 0000
0x51
8
V1OM3[31:0]
0x0000 0000
V1OM1[31:0]
0x0080 0000
V2OM6[31:0]
0x0000 0000
V2OM4[31:0]
0x0000 0000
V2OM2[31:0]
0x0080 0000
0x52
0x53–0xFF
(4)
u[31:26], b2[25:0]
u[31:26], (1 – ae)[25:0]
DRC2 (1 – aa)
0x3F
0x0000 0000
u[31:26], ae[25:0]
DRC 2 (1 – ae)
0x3E
0x0080 0000
u[31:26], b1[25:0]
Reserved
DRC1 (1 – ad)
0x3D
u[31:26], b0[25:0]
8
DRC1 (1 – aa)
0x3C
INITIALIZATION
VALUE
4
DRC1 (1 – ae)
0x3B
CONTENTS
12
4
Reserved
(4)
0x0000 0000
0x0000 0000
Reserved registers should not be accessed.
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s): TAS5716
43
TAS5716
SLOS569 – JANUARY 2009............................................................................................................................................................................................... www.ti.com
CLOCK CONTROL REGISTER (0x00)
In the manual mode, the clock control register provides a way for the system microprocessor to update the data
and clock rates based on the sample rate and associated clock frequencies. In the auto-detect mode, the clocks
are automatically determined by the TAS5716. In this case, the clock control register contains the auto-detected
clock status as automatically detected (D7–D2). Bits D7–D5 select the sample rate. Bits D4–D2 select the MCLK
frequency. Bit D0 is used in manual mode only. In this mode, when the clocks are updated a 1 must be written to
D0 to inform the DAP that the written clocks are valid.
Table 3. Clock Control Register (0x00)
D7
D6
D5
D4
D3
D2
D1
D0
0
0
0
–
–
–
–
–
fS = 32-kHz sample rate
FUNCTION
0
0
1
–
–
–
–
–
fS = 38-kHz sample rate
0
1
0
–
–
–
–
–
fS = 44.1-kHz sample rate
0
1
1
–
–
–
–
–
fS = 48-kHz sample rate (1)
1
0
0
–
–
–
–
–
fS = 88.2-kHz sample rate
1
0
1
–
–
–
–
–
fS = 96-kHz sample rate
1
1
0
–
–
–
–
–
fS = 176.4-kHz sample rate
1
1
1
–
–
–
–
–
fS = 192-kHz sample rate
–
–
–
0
0
0
–
–
MCLK frequency = 64 × fS (2)
–
–
–
0
0
1
–
–
MCLK frequency = 128 × fS (3)
–
–
–
0
1
0
–
–
MCLK frequency = 192 × fS
–
–
–
0
1
1
–
–
MCLK frequency = 256 × fS
(1)
(4)
–
–
–
1
0
0
–
–
MCLK frequency = 384 × fS
–
–
–
1
0
1
–
–
MCLK frequency = 512 × fS (4)
–
–
–
1
1
0
–
–
Reserved
–
–
–
1
1
1
–
–
Reserved
–
–
–
–
–
–
0
–
Bit clock (SCLK) frequency = 64 × fS or 32 × fS (selected in register 0x04) (1)
–
–
–
–
–
–
1
–
Bit clock (SCLK) frequency = 48 × fS (5)
–
–
–
–
–
–
–
0
Clock not valid (in manual mode only) (1)
–
–
–
–
1
Clock valid (in manual mode only)
(1)
(2)
(3)
(4)
(5)
Default values are in bold.
Rate not available for 32-KHz data rate or in AM avoidance mode
Rate not available for 32-kHz data rate
Rate not available for 176.4-kHz and 192-kHz data rates
Rate only available for 192-fS and 384-fS MCLK frequencies
DEVICE ID REGISTER (0x01)
The device ID register contains the ID code for the firmware revision.
Table 4. General Status Register (0x01)
D7
D6
D5
D4
D3
D2
D1
D0
0
–
–
–
–
–
–
–
Default (1)
–
0
1
0
1
0
0
0
Identification code
(1)
44
FUNCTION
Default values are in bold.
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s): TAS5716
TAS5716
www.ti.com............................................................................................................................................................................................... SLOS569 – JANUARY 2009
ERROR STATUS REGISTER (0x02)
Note that the error bits are sticky bits that are not cleared by the hardware. This means that the software must
clear the register (write zeroes) and then read them to determine if there are any persistent errors.
Table 5. Error Status Register (0x02)
D7
D6
D5
D4
D3
D2
D1
D0
1
–
–
–
–
–
–
–
MCLK error
–
1
–
–
–
–
–
–
PLL autolock error
–
–
1
–
–
–
–
–
SCLK error
–
–
–
1
–
–
–
–
LRCLK error
–
–
–
–
1
–
–
–
Frame slip
0
0
0
0
0
0
0
0
No errors (1)
(1)
FUNCTION
Default values are in bold.
Note that the error bits are sticky bits that are not cleared by the hardware. This means that the software must
clear the register (write zeroes) and then read them to determine if there are any persistent errors.
Table 6. Error Status Register (0x02)
D7
D6
D5
D4
D3
D2
D1
D0
–
1
–
–
–
–
–
–
PLL autolock error
–
–
1
–
–
–
–
–
SCLK error
–
–
–
1
–
–
–
–
LRCLK error
–
–
–
–
1
–
–
–
Frame slip
0
0
0
0
0
0
0
0
No errors (1)
(1)
FUNCTION
Default values are in bold.
SYSTEM CONTROL REGISTER 1 (0x03)
The system control register 1 has several functions:
Bit D7:
If 0, the dc-blocking filter for each channel is disabled.
If 1, the dc-blocking filter (–3 dB cutoff < 1 Hz) for each channel is enabled (default).
Bit D5:
If 0, use soft unmute on recovery from clock error. This is a slow recovery.
If 1, use hard unmute on recovery from clock error (default). This is a fast recovery.
Bit D3:
If 0, clock autodetect is enabled (default).
If 1, clock autodetect is disabled.
Bit D2:
If 0, soft start is enabled (default).
If 1, soft start is disabled.
Bits D1–D0: Select de-emphasis
Table 7. System Control Register 1 (0x03)
D7
D6
D5
D4
D3
D2
D1
D0
0
–
–
–
–
–
–
–
PWM high-pass (dc blocking) disabled
1
–
–
–
–
–
–
–
PWM high-pass (dc blocking) enabled (1)
–
0
–
–
–
–
–
–
Reserved (1)
–
–
0
–
–
–
–
–
Soft unmute on recovery from clock error
–
–
1
–
–
–
–
–
Hard unmute on recovery from clock error (1)
–
–
–
0
–
–
–
–
Reserved (1)
–
–
–
–
0
–
–
–
Enable clock autodetect (1)
(1)
FUNCTION
Default values are in bold.
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s): TAS5716
45
TAS5716
SLOS569 – JANUARY 2009............................................................................................................................................................................................... www.ti.com
Table 7. System Control Register 1 (0x03) (continued)
D7
D6
D5
D4
D3
D2
D1
D0
FUNCTION
–
–
–
–
1
–
–
–
Disable clock autodetect
–
–
–
–
–
0
–
–
Enable soft start (1)
–
–
–
–
–
1
–
–
Disable soft start
–
–
–
–
–
–
0
0
No de-emphasis (1)
–
–
–
–
–
–
0
1
Reserved
–
–
–
–
–
–
1
0
De-emphasis for fS = 44.1 kHz
–
–
–
–
–
–
1
1
De-emphasis for fS = 48 kHz
SERIAL DATA INTERFACE REGISTER (0x04)
As shown in Table 8, the TAS5716 supports 12 serial data modes. The default is 24-bit, I2S mode.
Table 8. Serial Data Interface Control Register (0x04) Format
RECEIVE SERIAL DATA
INTERFACE FORMAT
WORD
LENGTH
D7–D5
D4
D3
D2
D1
D0
Right-justified
16
000
0
0
0
0
0
Right-justified
20
000
0
0
0
0
1
Right-justified
24
000
0
0
0
1
0
I2S
16
000
0
0
0
1
1
20
000
0
0
1
0
0
24
000
0
0
1
0
1
Left-justified
16
000
0
0
1
1
0
Left-justified
20
000
0
0
1
1
1
Left-justified
24
000
0
1
0
0
0
000
0
1
0
0
1
000
0
1
0
1
0
Reserved
000
0
1
0
1
1
Reserved
000
0
1
1
0
0
Reserved
000
0
1
1
0
1
Reserved
000
0
1
1
1
0
Reserved
000
0
1
1
1
1
Reserved
000
1
0
0
0
0
Reserved
000
1
0
0
0
1
Reserved
000
1
0
0
1
0
000
1
0
0
1
1
000
1
0
1
0
0
000
1
0
1
0
1
000
1
0
1
1
0
Reserved
000
1
0
1
1
1
Reserved
000
1
1
X
X
X
2
I S
I2S
(1)
Reserved
Right-justified
I2S (32 fS SCLK)
18
16
Reserved
Reserved
Left-justified (32 fS SCLK)
(1)
46
16
Default values are in bold.
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s): TAS5716
TAS5716
www.ti.com............................................................................................................................................................................................... SLOS569 – JANUARY 2009
SYSTEM CONTROL REGISTER 2 (0x05)
Bit D6 is a control bit and bit D5 is a configuration bit.
When bit D6 is set low, the system starts playing; otherwise, the outputs are shut down.
Bit D5 defines the configuration of the system, that is, it determines what configuration the system runs in when
bit D6 is set low. When this bit is asserted, all channels are switching. Otherwise, only a subset of the PWM
channels can run. The channels to shut down are defined in the shutdown group register (0x19). Bit D5 should
only be changed when bit D6 is set, meaning that it is only possible to switch configurations by resetting the DAP
and then restarting it again in the new configuration.
Bit D3 defines which volume register is used to control the volume of the HP_PWMx outputs when in headphone
mode. When set to 0, the HP volume register (0x0C) controls the volume of the headphone outputs when in
headphone mode. When bit D3 is set to 1, the channel volume registers (0x08–0x0B, 0x0D) are used for all
modes (line out, headphone, speaker).
Bits D2–D1 define the output modes. The default is speaker mode with the headphone mode selectable via the
external HPSEL terminal. The device can also be forced into headphone mode by asserting bit D1 (all other
PWM channels are muted). Asserting bit D2 puts the device into a pseudo-line-out mode where the HP_PWMx
and all other PWM channels are active. Bit D3 must also be asserted in this mode, and the HP_PWMx volume is
controlled with the main speaker output volume controls via registers 0x08–0x0B and 0x0D..
Table 9. System Control Register 2 (0x05)
D7
D6
D5
D4
D3
D2
D1
D0
FUNCTION
(1)
0
–
–
–
–
–
–
–
Reserved
–
1
0
–
–
–
–
–
All channels are shut down (hard mute). VALID1 = 0.
–
1
1
–
–
–
–
–
All channels are shut down (hard mute). VALID1 = 0 (2)
–
0
0
–
–
–
–
–
When D6 is deasserted, all channels not belonging to shutdown group (SDG) are started.
SDG register is 0x19.
–
0
1
–
–
–
–
–
When D6 is deasserted, all channels are started. VALID1 = 1. No channels in SDG1.
–
–
–
0
–
–
–
–
Reserved (2)
–
–
–
–
0
–
–
–
Use HP volume register (0x0C) for adjusting headphone volume when in
headphone mode. (2)
–
–
–
–
1
–
–
–
Use channel volume registers (0x08–0x0B, 0x0D) for all modes.
–
–
–
–
–
0
0
–
Speaker mode. Hardware pin, HPSEL = 1, forces device into headphone mode. (2)
–
–
–
–
–
0
1
–
HP mode. This setting is logically ORed with external HPSEL pin.
–
–
–
–
–
1
0
–
Line out mode. Hardware pin, HPSEL, is ignored for this setting. HP_PWMx pins are
active.
–
–
–
–
–
1
1
–
Reserved
–
–
–
–
–
–
–
0
Reserved (2)
(1)
(2)
Default values are in bold.
Default values are in bold.
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s): TAS5716
47
TAS5716
SLOS569 – JANUARY 2009............................................................................................................................................................................................... www.ti.com
SOFT MUTE REGISTER (0x06)
Writing a 1 to any of the following bits sets the output of the respective channel to 50% duty cycle. Default is
0x00.
Table 10. Soft Mute Register (0x06)
D7
D6
D5
D4
D3
D2
D1
D0
–
–
–
–
–
–
–
1
Soft mute channel 1
–
–
–
–
–
–
1
–
Soft mute channel 2
–
–
–
–
–
1
–
–
Soft mute channel 3
–
–
–
–
1
–
–
–
Soft mute channel 4
–
–
1
–
–
–
–
–
Soft mute subwoofer channel (channel 6)
0
0
0
0
0
0
0
0
Unmute all channels (1)
(1)
FUNCTION
Default values are in bold.
VOLUME REGISTERS (0x07, 0x08, 0x09, 0x0A, 0x0B, 0x0C, 0x0D)
Step size is 0.5 dB.
Master volume
– 0x07 (default is mute)
Channel-1 volume
– 0x08 (default is 0 dB)
Channel-2 volume
– 0x09 (default is 0 dB)
Channel-3 volume
– 0x0A (default is 0 dB)
Channel-4 volume
– 0x0B (default is 0 dB)
Headphone volume
– 0x0C (default is 0 dB)
Channel-6 volume
(subwoofer)
– 0x0D (default is 0 dB)
Table 11. Volume Register
D7
D6
D5
D4
D3
D2
D1
D0
0
0
0
0
0
0
0
0
24 dB
0
0
1
1
0
0
0
0
0 dB (default for individual channel volume) (1)
1
1
1
1
1
1
1
0
–100 dB
1
1
1
1
1
1
1
1
MUTE (default for master volume); 50% duty cycle at output – SOFT MUTE (1)
(1)
48
FUNCTION
Default values are in bold.
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s): TAS5716
TAS5716
www.ti.com............................................................................................................................................................................................... SLOS569 – JANUARY 2009
VOLUME CONFIGURATION REGISTER (0x0E)
Bit D7:
Reserved = 1
Bit D6:
If 0, then biquad 1 (BQ1) volume compensation part only is disabled (default). If 1, then BQ1
volume compensation is enabled.
Bit D4:
Reserved = 1
Bit D3:
Reserved
Bits D2–D0:
Volume slew rate (Used to control volume change and MUTE ramp rates)
Table 12. Volume Control Register (0x0E)
D7
D6
D5
D4
D3
D2
D1
D0
FUNCTION
(1)
1
–
–
–
–
–
–
–
Reserved (must be 1)
–
0
–
–
–
–
–
–
Disable biquad volume compensation (1)
–
1
–
–
–
–
–
–
Enable biquad volume compensation
–
–
0
–
–
–
–
–
Reserved (1)
–
–
–
1
–
–
–
–
Reserved (must be 1) (1)
–
–
–
–
0
–
–
–
Reserved (1)
–
–
–
–
–
0
0
0
Volume slew 512 steps (44 ms volume ramp time)
–
–
–
–
–
0
0
1
Volume slew 1024 steps (1) (88 ms volume ramp time)
–
–
–
–
–
0
1
0
Volume slew 2048 steps (176 ms volume ramp time)
–
–
–
–
–
0
1
1
Volume slew 256 steps (22 ms volume ramp time)
–
–
–
–
–
1
X
X
Reserved
(1)
Default values are in bold.
MODULATION LIMIT REGISTER (0x10)
Set modulation limit. See the appropriate power stage data sheet for recommended modulation limits.
Table 13. Modulation Limit Register (0x10)
(1)
D7
D6
D5
D4
D3
D2
D1
D0
LIMIT
[DCLKs]
MIN WIDTH [DCLKs]
MODULATION LIMIT
–
–
–
–
–
0
0
0
1
2
99.2%
–
–
–
–
–
0
0
1
2
4
98.4%
–
–
–
–
–
0
1
0
3
6
–
–
–
–
–
0
1
1
4
8
96.9%
–
–
–
–
–
1
0
0
5
10
96.1%
–
–
–
–
–
1
0
1
6
12
95.3%
–
–
–
–
–
1
1
0
7
14
94.5%
–
–
–
–
–
1
1
1
8
16
93.8%
97.7%
(1)
Default values are in bold.
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s): TAS5716
49
TAS5716
SLOS569 – JANUARY 2009............................................................................................................................................................................................... www.ti.com
INTERCHANNEL DELAY REGISTERS (0x11, 0x12, 0x13, 0x14, 0x15, 0x16)
Internal PWM Channels 1, 2, 3, 4, 5, and 6 are mapped into registers 0x11, 0x12 ,0x13, 0x14, 0x15, and 0x16.
Table 14. Channel Interchannel Delay Register Format
BITS DEFINITION
D7
D6
D5
D4
D3
D2
D1
D0
0
0
0
0
0
0
0
0
Minimum absolute delay, 0 DCLK cycles, default for
channel 0 (1)
0
1
1
1
1
1
0
0
Maximum positive delay, 31 × 4 DCLK cycles
1
0
0
0
0
0
0
0
Maximum negative delay, –32 × 4 DCLK cycles
0
Unused bits
0
FUNCTION
A
SUBADDRESS
D7
D6
D5
D4
D3
D2
D1
D0
Delay = (value) × 4 DCLKs
0x11
0
1
0
0
1
1
0
0
Default value for channel 1
(1)
(1)
(1)
19
0x12
0
0
1
1
0
1
0
0
Default value for channel 2
0x13
0
0
0
1
1
1
0
0
Default value for channel 3
(1)
7
0x14
0
1
1
0
0
1
0
0
Default value for channel 4
(1)
25
–12
-28
0x15
1
1
0
1
0
0
0
0
Default value for channel 5
(1)
0x16
1
0
0
1
0
0
0
0
Default value for channel 6
(1)
13
Default values are in bold.
OFFSET REGISTER (0x17)
The offset register is mapped into 0x17.
Table 15. Channel Offset Register Format
D7
D6
D5
D4
D3
D2
D1
D0
0
0
0
0
0
0
0
0
Minimum absolute offset, 0 DCLK cycles, default for channel 0 (1)
1
1
1
1
1
1
1
1
Maximum absolute offset, 255 DCLK cycles
(1)
50
FUNCTION
Default values are in bold.
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s): TAS5716
TAS5716
www.ti.com............................................................................................................................................................................................... SLOS569 – JANUARY 2009
PWM SHUTDOWN GROUP REGISTER (0x19)
Settings of this register determine which PWM channels are active. The default is 0x30 for two BTL output
channels and no external subwoofer output. The functionality of this register is tied to the state of bit D5 in the
system control register.
This register defines which channels belong to the shutdown group (SDG). If a 1 is set in the shutdown group
register, that particular channel is not started following an exit out of all-channel shutdown command (if bit D5 is
set to 0 in system control register 2, 0x05).
Table 16. Shutdown Group Register
D7
D6
D5
D4
D3
D2
D1
D0
FUNCTION
(1)
0
–
–
–
–
–
–
–
Reserved
–
0
–
–
–
–
–
–
Reserved (1)
–
–
0
–
–
–
–
–
Channel 6 does not belong to shutdown group.
–
–
1
–
–
–
–
–
Channel 6 belongs to shut down group. (1)
–
–
–
0
–
–
–
–
Channel 5 does not belong to shutdown group.
–
–
–
1
–
–
–
–
Channel 5 belongs to shutdown group. (1)
–
–
–
–
0
–
–
–
Channel 4 does not belong to shutdown group.
–
–
–
–
1
–
–
–
Channel 4 belongs to shutdown group.
–
–
–
–
–
0
–
–
Channel 3 does not belong to shutdown group. (1)
–
–
–
–
–
1
–
–
Channel 3 belongs to shutdown group.
–
–
–
–
–
–
0
–
Channel 2 does not belong to shutdown group. (1)
–
–
–
–
–
–
1
–
Channel 2 belongs to shutdown group.
–
–
–
–
–
–
–
0
Channel 1 does not belong to shutdown group. (1)
–
–
–
–
–
–
–
1
Channel 1 belongs to shutdown group.
(1)
(1)
Default values are in bold.
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s): TAS5716
51
TAS5716
SLOS569 – JANUARY 2009............................................................................................................................................................................................... www.ti.com
START/STOP PERIOD REGISTER (0x1A)
This register is used to control the soft-start and soft-stop period when starting up or shutting down channels.
The value in this register determines the time for which the PWM inputs switch at 50% duty cycle. This helps
reduce pops and clicks at start-up and shutdown.
D7 is used to configure the output stage in a bridge-tied mode or a single-ended mode.
Table 17. Start/Stop Period Register (0x1A)
D7
D6
D5
D4
D3
D2
D1
D0
0
–
–
–
–
–
–
–
Bridge-tied load (BTL) (1)
1
–
–
–
–
–
–
–
Single-ended load (SE)
–
–
–
0
0
–
–
–
No 50% duty cycle start/stop period
–
–
–
0
1
0
0
0
16.5-ms 50% duty cycle start/stop period
–
–
–
0
1
0
0
1
23.9-ms 50% duty cycle start/stop period
–
–
–
0
1
0
1
0
31.4-ms 50% duty cycle start/stop period (1)
–
–
–
0
1
0
1
1
40.4-ms 50% duty cycle start/stop period
–
–
–
0
1
1
0
0
53.9-ms 50% duty cycle start/stop period
–
–
–
0
1
1
0
1
70.3-ms 50% duty cycle start/stop period
–
–
–
0
1
1
1
0
94.2-ms 50% duty cycle start/stop period
–
–
–
0
1
1
1
1
125.7-ms 50% duty cycle start/stop period
–
–
–
1
0
0
0
0
164.6-ms 50% duty cycle start/stop period
–
–
–
1
0
0
0
1
239.4-ms 50% duty cycle start/stop period
–
–
–
1
0
0
1
0
314.2-ms 50% duty cycle start/stop period
–
–
–
1
0
0
1
1
403.9-ms 50% duty cycle start/stop period
–
–
–
1
0
1
0
0
538.6-ms 50% duty cycle start/stop period
–
–
–
1
0
1
0
1
703.1-ms 50% duty cycle start/stop period
–
–
–
1
0
1
1
0
942.5-ms 50% duty cycle start/stop period
–
–
–
1
0
1
1
1
1256.6-ms 50% duty cycle start/stop period
–
–
–
1
1
0
0
0
1728.1-ms 50% duty cycle start/stop period
–
–
–
1
1
0
0
1
2513.6-ms 50% duty cycle start/stop period
–
–
–
1
1
0
1
0
3299.1-ms 50% duty cycle start/stop period
–
–
–
1
1
0
1
1
4241.7-ms 50% duty cycle start/stop period
–
–
–
1
1
1
0
0
5655.6-ms 50% duty cycle start/stop period
–
–
–
1
1
1
0
1
7383.7-ms 50% duty cycle start/stop period
–
–
–
1
1
1
1
0
9897.3-ms 50% duty cycle start/stop period
–
–
–
1
1
1
1
1
13,196.4-ms 50% duty cycle start/stop period
(1)
52
FUNCTION
Default values are in bold.
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s): TAS5716
TAS5716
www.ti.com............................................................................................................................................................................................... SLOS569 – JANUARY 2009
OSCILLATOR TRIM REGISTER (0x1B)
The TAS5716 PWM processor contains an internal oscillator for PLL reference. This reduces system cost
because an external reference is not required. Currently, TI recommends a trim resistor value of 18.2 kΩ (1%).
This should be connected between OSC_RES and DVSS.
The factory-trim procedure simply enables the factory trim that was previously done at the factory.
Note that trim always must be run following reset of the device.
Oscillator Trim Enable Procedure Example
Write data 0x00 to register 0x1B (enable factory trim).
Table 18. Oscillator Trim Register (0x1B)
D7
D6
D5
D4
D3
D2
D1
D0
1
–
–
–
–
–
–
–
Reserved
–
0
–
–
–
–
–
–
Oscillator trim not done (read-only) (1)
–
1
–
–
–
–
–
–
Oscillator trim done (read only)
–
–
0
0
0
0
–
–
Reserved
–
–
–
–
–
–
0
–
Select factory trim (Write a 0 to select factory trim; default is 1.)
–
–
–
–
–
–
1
–
Factory trim disabled (1)
–
–
–
–
–
–
–
0
Reserved (1)
(1)
FUNCTION
(1)
(1)
Default values are in bold.
BKND_ERR REGISTER (0x1C)
When a back-end error signal is received (BKND_ERR = LOW), all the output stages are reset by setting all
PWM, VALID1, and VALID2 signals LOW. Subsequently, the modulator waits approximately for the time listed in
Table 19 before initiation of a reset.
Table 19. BKND_ERR Register (0x1C)
D7
D6
D5
D4
D3
D2
D1
D0
–
–
–
–
0
0
0
0
Set back-end reset period to 0 ms (Reserved)
–
–
–
–
0
0
0
1
Set back-end reset period to 150 ms (Reserved)
–
–
–
–
0
0
1
0
Set back-end reset period to 299 ms (1)
–
–
–
–
0
0
1
1
Set back-end reset period to 449 ms
–
–
–
–
0
1
0
0
Set back-end reset period to 598 ms
–
–
–
–
0
1
0
1
Set back-end reset period to 748 ms
–
–
–
–
0
1
1
0
Set back-end reset period to 898 ms
–
–
–
–
0
1
1
1
Set back-end reset period to 1047 ms
–
–
–
–
1
0
0
0
Set back-end reset period to 1197 ms
–
–
–
–
1
0
0
1
Set back-end reset period to 1346 ms
–
–
–
–
1
0
1
0
Set back-end reset period to 1496 ms
–
–
–
–
1
0
1
1
Set back-end reset period to 1496 ms
–
–
–
–
1
1
–
–
Set back-end reset period to 1496 ms
(1)
FUNCTION
Default values are in bold.
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s): TAS5716
53
TAS5716
SLOS569 – JANUARY 2009............................................................................................................................................................................................... www.ti.com
INPUT MULTIPLEXER REGISTER (0x20)
The hex value for each nibble is the channel number. For each input multiplexer, any input from SDIN1, SDIN2
can be mapped to any internal TAS5716 channel.
Table 20. Input Multiplexer Register (0x20)
(1)
54
D31
D30
D29
D28
D27
D26
D25
D24
0
0
0
0
0
0
0
0
FUNCTION
D23
D22
D21
D20
D19
D18
D17
D16
0
–
–
–
–
–
–
–
Channel-1 AD mode
1
–
–
–
–
–
–
–
Channel-1 BD mode (1)
–
0
0
0
–
–
–
–
SDIN1-L to channel 1 (1)
–
0
0
1
–
–
–
–
SDIN1-R to channel 1
–
0
1
0
–
–
–
–
SDIN2-L to channel 1
–
0
1
1
–
–
–
–
SDIN2-R to channel 1
–
1
0
0
–
–
–
–
Reserved
–
1
0
1
–
–
–
–
Reserved
–
1
1
0
–
–
–
–
Ground (0) to channel 1
–
1
1
1
–
–
–
–
Reserved
–
–
–
–
0
–
–
–
Channel 2 AD mode
–
–
–
–
1
–
–
–
Channel 2 BD mode (1)
–
–
–
–
–
0
0
0
SDIN1-L to channel 2
–
–
–
–
–
0
0
1
SDIN1-R to channel 2 (1)
–
–
–
–
–
0
1
0
SDIN2-L to channel 2
–
–
–
–
–
0
1
1
SDIN2-R to channel 2
–
–
–
–
–
1
0
0
Reserved
–
–
–
–
–
1
0
1
Reserved
–
–
–
–
–
1
1
0
Ground (0) to channel 2
–
–
–
–
–
1
1
1
Reserved
Reserved = 0x00 (1)
FUNCTION
Default values are in bold.
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s): TAS5716
TAS5716
www.ti.com............................................................................................................................................................................................... SLOS569 – JANUARY 2009
Table 20. Input Multiplexer Register (0x20) (continued)
D15
(2)
D14
D13
D12
D11
D10
D9
D8
FUNCTION
(2)
0
–
–
–
–
–
–
–
Reserved
–
0
0
0
–
–
–
–
SDIN1-L to channel 3
–
0
0
1
–
–
–
–
SDIN1-R to channel 3
–
0
1
0
–
–
–
–
SDIN2-L to channel 3
–
0
1
1
–
–
–
–
SDIN2-R to channel 3
–
1
0
0
–
–
–
–
Reserved
–
1
0
1
–
–
–
–
Reserved
–
1
1
0
–
–
–
–
Ground (0) to channel 3
–
1
1
1
–
–
–
–
Ch1 (BTL–) to channel 3—BTL pair for channel 1 (2)
–
–
–
–
0
–
–
–
Reserved (2)
–
–
–
–
–
0
0
0
SDIN1-L to channel 4
–
–
–
–
–
0
0
1
SDIN1-R to channel 4
–
–
–
–
–
0
1
0
SDIN2-L to channel 4
–
–
–
–
–
0
1
1
SDIN2-R to channel 4
–
–
–
–
–
1
0
0
Reserved
–
–
–
–
–
1
0
1
Reserved
–
–
–
–
–
1
1
0
Ground (0) to channel 4
–
–
–
–
–
1
1
1
Ch2 (BTL–) to channel 4—BTL pair for channel 2 (2)
D7
D6
D5
D4
D3
D2
D1
D0
FUNCTION
(2)
0
–
–
–
–
–
–
–
Reserved
–
1
0
0
–
–
–
–
Reserved
–
1
0
1
–
–
–
–
Reserved
–
1
1
0
–
–
–
–
Ground (0) to channel 5
–
1
1
1
–
–
–
–
Ch6 (BTL–) to channel 5—BTL pair to channel 6 (2)
–
–
–
–
0
–
–
–
Channel 6 AD mode
–
–
–
–
1
–
–
–
Channel 6 BD mode (2)
–
–
–
–
–
0
0
0
SDIN1-L to channel 6
–
–
–
–
–
0
0
1
SDIN1-R to channel 6
–
–
–
–
–
0
1
0
SDIN2-L to channel 6
–
–
–
–
–
0
1
1
SDIN2-R to channel 6
–
–
–
–
–
1
0
0
Reserved
–
–
–
–
–
1
0
1
Reserved
–
–
–
–
–
1
1
0
Ground (0) to channel 6
–
–
–
–
–
1
1
1
Reserved
(2)
Default values are in bold.
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s): TAS5716
55
TAS5716
SLOS569 – JANUARY 2009............................................................................................................................................................................................... www.ti.com
CHANNEL-6 INPUT MULTIPLEXER-2 REGISTER (0x21)
Bits D31–D16:
Unused
Bits D15–D10:
Reserved
Bits D7–D0:
Reserved
Table 21. Downmix Input Multiplexer Register
D31
D30
D29
D28
D27
D26
D25
D24
–
–
–
–
–
–
–
–
D23
D22
D21
D20
D19
D18
D17
D16
–
–
–
–
–
–
–
–
D15
D14
D13
D12
D11
D10
D9
D8
56
FUNCTION
Unused
FUNCTION
(1)
0
1
0
0
0
0
–
–
Reserved
–
–
–
–
–
–
0
0
Enable channel 6 data to channel 6
–
–
–
–
–
–
0
1
Enable bass management on channel 6
–
–
–
–
–
–
1
0
Enable (L+R)/2 TO channel 6 (1)
–
–
–
–
–
–
1
1
Reserved
D7
D6
D5
D4
D3
D2
D1
D0
0
(1)
FUNCTION
Unused
0
0
0
0
0
1
1
FUNCTION
Reserved
(1)
Default values are in bold.
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s): TAS5716
TAS5716
www.ti.com............................................................................................................................................................................................... SLOS569 – JANUARY 2009
AM MODE REGISTER (0x22)
See the PurePath Digital™ AM Interference Avoidance application note (SLEA040).
Table 22. AM Mode Register (0x22)
D20
D19
D18
D17
D16
FUNCTION
(1)
0
–
–
–
–
AM mode disabled
1
–
–
–
–
AM mode enabled
–
0
0
–
–
Select sequence 1 (1)
–
0
1
–
–
Select sequence 2
–
1
0
–
–
Select sequence 3
–
1
1
–
–
Select sequence 4
–
–
–
0
–
IF frequency = 455 kHz (1)
–
–
–
1
–
IF frequency = 262.5 kHz
–
–
–
–
0
Use BCD tuned frequency (1)
–
–
–
–
1
Use binary tuned frequency
(1)
Default values are in bold.
Table 23. AM Tuned Frequency Register in BCD Mode
D15
D14
D13
D12
D11
D10
D9
D8
0
0
0
X
–
–
–
–
BCD frequency (1000s kHz)
–
–
–
–
X
X
X
X
BCD frequency (100s kHz)
0
0
0
0
0
0
0
0
Default value (1)
D7
D6
D5
D4
D3
D2
D1
D0
X
X
X
X
–
–
–
–
BCD frequency (10s kHz)
–
–
–
–
X
X
X
X
BCD frequency (1s kHz)
0
0
0
0
0
0
0
0
Default value (1)
(1)
FUNCTION
FUNCTION
Default values are in bold.
OR
Table 24. AM Tuned Frequency Register in Binary Mode
D15
D14
D13
D12
D11
D10
D9
D8
0
0
0
0
0
X
X
X
Binary frequency
0
0
0
0
0
0
0
0
Default value (1)
D7
D6
D5
D4
D3
D2
D1
D0
X
X
X
X
X
X
X
X
Binary frequency
0
0
0
0
0
0
0
0
Default value (1)
(1)
FUNCTION
FUNCTION
Default values are in bold.
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s): TAS5716
57
TAS5716
SLOS569 – JANUARY 2009............................................................................................................................................................................................... www.ti.com
PWM OUTPUT MUX REGISTER (0x25)
This DAP output multiplexer selects which internal PWM channel is output to the external pins. Any channel can
be output to any external output pin.
Bits D30–D25:
Selects which PWM channel is output to HPL_PWM and HPR_PWM
Bits D23–D20:
Selects which PWM channel is output to OUT_A
Bits D19–D16:
Selects which PWM channel is output to OUT_B
Bits D15–D12:
Selects which PWM channel is output to OUT_C
Bits D11–D08:
Selects which PWM channel is output to OUT_D
Bits D07–D04:
Selects which PWM channel is output to SUB_PWM–
Bits D03–D00:
Selects which PWM channel is output to SUB_PWM+
Note that channels are encoded so that channel 1 = 0x00, channel 2 = 0x01, …, channel 6 = 0x05.
Table 25. PWM Output Mux Register (0x25)
D31
D30
D29
D28
D27
D26
D25
D24
0
–
–
–
–
–
–
–
Reserved (1)
–
0
0
0
–
–
–
–
Multiplex channel 1 to HPL_PWM (1)
–
0
0
1
–
–
–
–
Multiplex channel 2 to HPL_PWM
–
0
1
0
–
–
–
–
Multiplex channel 3 to HPL_PWM
–
0
1
1
–
–
–
–
Multiplex channel 4 to HPL_PWM
–
1
0
0
–
–
–
–
Multiplex channel 5 to HPL_PWM
–
1
0
1
–
–
–
–
Multiplex channel 6 to HPL_PWM
–
–
–
–
0
–
–
–
Reserved
–
–
–
–
–
0
0
0
Multiplex channel 1 to HPR_PWM
–
–
–
–
–
0
0
1
Multiplex channel 2 to HPR_PWM (1)
–
–
–
–
–
0
1
0
Multiplex channel 3 to HPR_PWM
–
–
–
–
–
0
1
1
Multiplex channel 4 to HPR_PWM
–
–
–
–
–
1
0
0
Multiplex channel 5 to HPR_PWM
–
–
–
–
–
1
0
1
Multiplex channel 6 to HPR_PWM
D23
D22
D21
D20
D19
D18
D17
D16
0
0
0
0
–
–
–
–
Multiplex channel 1 to OUT_A (1)
0
0
0
1
–
–
–
–
Multiplex channel 2 to OUT_A
0
0
1
0
–
–
–
–
Multiplex channel 3 to OUT_A
0
0
1
1
–
–
–
–
Multiplex channel 4 to OUT_A
0
1
0
0
–
–
–
–
Multiplex channel 5 to OUT_A
0
1
0
1
–
–
–
–
Multiplex channel 6 to OUT_A
–
–
–
–
0
0
0
0
Multiplex channel 1 to OUT_B
–
–
–
–
0
0
0
1
Multiplex channel 2 to OUT_B
–
–
–
–
0
0
1
0
Multiplex channel 3 to OUT_B (1)
–
–
–
–
0
0
1
1
Multiplex channel 4 to OUT_B
–
–
–
–
0
1
0
0
Multiplex channel 5 to OUT_B
–
–
–
–
0
1
0
1
Multiplex channel 6 to OUT_B
(1)
58
FUNCTION
FUNCTION
Default values are in bold.
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s): TAS5716
TAS5716
www.ti.com............................................................................................................................................................................................... SLOS569 – JANUARY 2009
Table 25. PWM Output Mux Register (0x25) (continued)
D15
D14
D13
D12
D11
D10
D9
D8
0
0
0
0
–
–
–
–
Multiplex channel 1 to OUT_C
0
0
0
1
–
–
–
–
Multiplex channel 2 to OUT_C (2)
0
0
1
0
–
–
–
–
Multiplex channel 3 to OUT_C
0
0
1
1
–
–
–
–
Multiplex channel 4 to OUT_C
0
1
0
0
–
–
–
–
Multiplex channel 5 to OUT_C
0
1
0
1
–
–
–
–
Multiplex channel 6 to OUT_C
–
–
–
–
0
0
0
0
Multiplex channel 1 to OUT_D
–
–
–
–
0
0
0
1
Multiplex channel 2 to OUT_D
–
–
–
–
0
0
1
0
Multiplex channel 3 to OUT_D
–
–
–
–
0
0
1
1
Multiplex channel 4 to OUT_D (2)
–
–
–
–
0
1
0
0
Multiplex channel 5 to OUT_D
–
–
–
–
0
1
0
1
Multiplex channel 6 to OUT_D
D7
D6
D5
D4
D3
D2
D1
D0
0
0
0
0
–
–
–
0
0
0
1
–
–
–
–
Multiplex channel 2 to SUB_PWM–
0
0
1
0
–
–
–
–
Multiplex channel 3 to SUB_PWM–
0
0
1
1
–
–
–
–
Multiplex channel 4 to SUB_PWM–
0
1
0
0
–
–
–
–
Multiplex channel 5 to SUB_PWM– (2)
0
1
0
1
–
–
–
–
Multiplex channel 6 to SUB_PWM–
–
–
–
–
0
0
0
0
Multiplex channel 1 to SUB_PWM+
–
–
–
–
0
0
0
1
Multiplex channel 2 to SUB_PWM+
–
–
–
–
0
0
1
0
Multiplex channel 3 to SUB_PWM+
–
–
–
–
0
0
1
1
Multiplex channel 4 to SUB_PWM+
–
–
–
–
0
1
0
0
Multiplex channel 5 to SUB_PWM+
–
–
–
–
0
1
0
1
Multiplex channel 6 to SUB_PWM+ (2)
(2)
FUNCTION
FUNCTION
Multiplex channel 1 to SUB_PWM–
Default values are in bold.
LOUDNESS BIQUAD GAIN INVERSE REGISTER (0x26)
Bit D6 of the volume configuration register (0x0E) enables/disables gain compensation for BQ1. D6 = 0 disables
gain compensation (default); D6 = 1 enables gain compensation. Max/min biquad gain = ±4.
Table 26. Loudness Biquad Gain Inverse Register (3.23 Format)
(1)
CONTENT
DEFINITION
u[31:26], x[25:0]
1/G (1)
G = gain of the biquad
LOUDNESS SCALE REGISTER (0x28)
Table 27. Loudness Scale Register (3.23 Format)
(1)
CONTENT
DEFINITION
u[31:26], x[25:0]
Scale = 1/(1 – 1/G) (1)
G = gain of the biquad
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s): TAS5716
59
TAS5716
SLOS569 – JANUARY 2009............................................................................................................................................................................................... www.ti.com
DRC CONTROL (0x46)
D7
D6
D5
D4
D3
D2
D1
D0
FUNCTION
(1)
–
–
–
–
0
–
–
–
DRC1 independent of channel 4
–
–
–
–
1
–
–
–
DRC1 dependent of channel 4
–
–
–
–
–
0
–
–
DRC1 independent of channel 3 (1)
–
–
–
–
–
1
–
–
DRC1 dependent of channel 3
–
–
–
–
–
–
0
–
DRC2 (subchannel ) turned OFF (1)
–
–
–
–
–
–
1
–
DRC2 (subchannel ) turned ON
–
–
–
–
–
–
–
0
DRC1 (satellite channels) turned OFF (1)
–
–
–
–
–
–
–
1
DRC1 (satellite channels) turned ON
(1)
Default values are in bold.
BANK SWITCH AND HEADPHONE DRC/EQ CONTROL (0x50)
Table 28. Bank Switching Command
D7
D6
D5
D4
D3
D2
D1
D0
0
–
–
–
–
–
–
–
EQ disabled in headphone mode (1)
1
–
–
–
–
–
–
–
EQ enabled in headphone mode
–
0
–
–
–
–
–
–
DRC disabled in headphone mode (1)
–
1
–
–
–
–
–
–
DRC enabled in headphone mode
–
–
0
0
0
–
–
–
Reserved (1)
–
–
–
–
–
0
0
0
No bank switching. All updates to DAP (1)
–
–
–
–
–
0
0
1
Configure bank 1 (32 kHz)
–
–
–
–
–
0
1
0
Configure bank 2 (44.1/48 kHz)
–
–
–
–
–
0
1
1
Configure bank 3 (88.2/96 kHz and above)
–
–
–
–
–
1
0
0
Automatic bank selection
(1)
60
FUNCTION
Default values are in bold.
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s): TAS5716
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Applications
Amplifiers
amplifier.ti.com
Audio
www.ti.com/audio
Data Converters
dataconverter.ti.com
Automotive
www.ti.com/automotive
DLP® Products
www.dlp.com
Communications and
Telecom
www.ti.com/communications
DSP
dsp.ti.com
Computers and
Peripherals
www.ti.com/computers
Clocks and Timers
www.ti.com/clocks
Consumer Electronics
www.ti.com/consumer-apps
Interface
interface.ti.com
Energy
www.ti.com/energy
Logic
logic.ti.com
Industrial
www.ti.com/industrial
Power Mgmt
power.ti.com
Medical
www.ti.com/medical
Microcontrollers
microcontroller.ti.com
Security
www.ti.com/security
RFID
www.ti-rfid.com
Space, Avionics &
Defense
www.ti.com/space-avionics-defense
RF/IF and ZigBee® Solutions www.ti.com/lprf
Video and Imaging
www.ti.com/video
Wireless
www.ti.com/wireless-apps
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2010, Texas Instruments Incorporated