CYStech Electronics Corp. Spec. No. : C546P8 Issued Date : 2013.03.14 Revised Date : Page No. : 1/7 Dual Operational Comparator LM358P8 Description The LM358P8 consists of two independent high gain, internally frequency compensated operational amplifier. It can be operated from a single power supply and also split power supplies. Features • Internally frequency compensated for unity gain • Single supply operation:3V to 32V • Input common-mode voltage range includes ground • Large DC voltage gain • Pb-free lead plating and halogen-free package Applications • General purpose amplifier • Transducer amplifier Pin Configurations LM358P8 Pin1: OUTPUT 1 Pin5: INPUT 2 (+) Pin2: INPUT 1 (-) Pin6: INPUT 2 (-) Pin3: INPUT 1 (+) Pin7: OUTPUT 2 Pin4: Gnd/VEE Pin8: VCC CYStek Product Specification Spec. No. : C546P8 Issued Date : 2013.03.14 Revised Date : Page No. : 2/7 CYStech Electronics Corp. Absolute Maximum Rating(Ta=25℃) Parameter Power Supply Voltages Single Supply Split Supplies Symbol Value Unit VCC VCC, VEE 32 ±16 V Input Differential Voltage Range VIDR ±32 V Input Common Mode Voltage Range VICR -0.3 ~ +32 V Power Dissipation PD 570 mW Output Short Circuit Duration tSC Continuous Operating Temperature Topr 0 ~ +70 ℃ Storage Temperature Tstg -65 ~ +150 ℃ Electrical Characteristics (VCC=5V,Ta=25°C, VEE=GND, unless otherwise specified.) Parameter Symbol Min. Typ. Max. Unit VIO - 2.9 7.0 mV Input Offset Current IIO - 5 50 nA Input Bias Current IIB - 45 250 nA VICR 0 - VCC-1.5 V - 0.5 1.2 mA - 0.8 2.0 mA 25 100 - V/mV 26 - - 27 28 - VO(L) - 5 20 mV Common Mode Rejection Ratio CMRR 65 80 - dB Power Supply Rejection Ratio PSRR 65 100 - dB CS - 120 - dB ISC - 40 60 mA Isource 10 30 - mA 10 15 - mA 12 100 - μA - - VCC V Input Offset Voltage Input Common-Mode Voltage Power Supply Current Large Signal Voltage Gain Output Voltage-High Limit Output Voltage-Low Limit Channel Separation Test Condition VCM=0 to VCC-1.5V VO(p)=1.4V, Rs=0 VCC=30V RL=∞, VCC=5V, VO=0V RL=∞, VCC=30V, VO=0V VCC=15V, RL≥2kΩ VO(p)=1V to 11V VCC=30V, RL=2kΩ VCC=30V, RL=10kΩ VCC=5V, RL≥10kΩ f=1kHz to 20kHz Short Circuit Current to Ground Output Source Current Output Sink Current Differential Input Voltage LM358P8 Vi(+)=1V, Vi(-)=0V, VCC=15V, VO(p)=2V Vi(+)=0V, Vi(-)=1V, VCC=15V, VO(p)=2V Vi(+)=0V, Vi(-)=1V, VCC=15V, VO(p)=0.2V ICC GV VO(H) V Isink VIDR CYStek Product Specification CYStech Electronics Corp. Spec. No. : C546P8 Issued Date : 2013.03.14 Revised Date : Page No. : 3/7 Block Diagram Ordering Information Device LM358P8-0-UB-G LM358P8 Package DIP-8 (Pb-free lead plating and halogen-free package) Shipping 60 pcs / tube, 60 tubes/ box, 4 boxes/carton CYStek Product Specification CYStech Electronics Corp. Spec. No. : C546P8 Issued Date : 2013.03.14 Revised Date : Page No. : 4/7 Characteristic Curves LM358P8 CYStek Product Specification CYStech Electronics Corp. Spec. No. : C546P8 Issued Date : 2013.03.14 Revised Date : Page No. : 5/7 Characteristic Curves(Cont.) LM358P8 CYStek Product Specification CYStech Electronics Corp. Spec. No. : C546P8 Issued Date : 2013.03.14 Revised Date : Page No. : 6/7 Recommended wave soldering condition Product Pb-free devices Peak Temperature 250 +0/-5 °C Soldering Time 5 +1/-1 seconds Recommended temperature profile for IR reflow Profile feature Average ramp-up rate (Tsmax to Tp) Preheat −Temperature Min(TS min) −Temperature Max(TS max) −Time(ts min to ts max) Time maintained above: −Temperature (TL) − Time (tL) Peak Temperature(TP) Time within 5°C of actual peak temperature(tp) Ramp down rate Time 25 °C to peak temperature Sn-Pb eutectic Assembly Pb-free Assembly 3°C/second max. 3°C/second max. 100°C 150°C 60-120 seconds 150°C 200°C 60-180 seconds 183°C 60-150 seconds 240 +0/-5 °C 217°C 60-150 seconds 250 +0/-5 °C 10-30 seconds 20-40 seconds 6°C/second max. 6°C/second max. 6 minutes max. 8 minutes max. Note : All temperatures refer to topside of the package, measured on the package body surface. LM358P8 CYStek Product Specification CYStech Electronics Corp. Spec. No. : C546P8 Issued Date : 2013.03.14 Revised Date : Page No. : 7/7 DIP-8 Dimension Marking: Date Code LM358 □□□□ Device Name DIP-8 Plastic Package CYStek Package Code : P8 Millimeters Min. Max. 3.710 4.310 0.510 3.200 3.600 0.380 0.570 1.524 (BSC) 0.204 0.360 DIM A A1 A2 B B1 C Inches Min. Max. 0.146 0.170 0.020 0.126 0.142 0.015 0.022 0.060 (BSC) 0.008 0.014 DIM D E E1 e L E2 Millimeters Min. Max. 9.000 9.400 6.200 6.600 7.320 7.920 2.540 (BSC) 3.000 3.600 8.400 9.000 Inches Min. Max. 0.354 0.370 0.244 0.260 0.288 0.312 0.100 (BSC) 0.118 0.142 0.331 0.354 Notes : 1.Controlling dimension : millimeters. 2.Maximum lead thickness includes lead finish thickness, and minimum lead thickness is the minimum thickness of base material. 3.If there is any question with packing specification or packing method, please contact your local CYStek sales office. Material : • Mold Compound : Epoxy resin family, flammability solid burning class:UL94V-0. Important Notice: • All rights are reserved. Reproduction in whole or in part is prohibited without the prior written approval of CYStek. • CYStek reserves the right to make changes to its products without notice. • CYStek semiconductor products are not warranted to be suitable for use in Life-Support Applications, or systems. • CYStek assumes no liability for any consequence of customer product design, infringement of patents, or application assistance. LM358P8 CYStek Product Specification