Quick Installation Guide

LevelOne
WBR-6011
N_Max Wireless Router
Quick Installation Guide
English
1
Table of Contents
English ......................................................................................... 3
2
English
Package Contents
 WBR-6011 N_Max Wireless Router
 Power Adapter (12VDC, 1A)
 RJ-45 LAN Ethernet Cable
 Rubber Feet
 CD User Manual
 Quick Installation Guide
If any of the above items are missing, please contact your retailer
or distributor.
3
Before You Begin
Please note the default settings listed below.
Default Settings
IP Address
192.168.0.1
User / Password
admin / password
Wireless Mode
Enable
Wireless SSID
WBR-6011
Security
None
This Quick Installation Guide only describes the most basic
situations and settings. Please consult the User Manual on the CD
for more details.
Please have your Internet Service Provider’s username, password
or other connection details ready.
4
Installation
1. Please power off your ADSL / Cable modem by unplugging
the power adapter.
2.
Attach the included antennas.
3.
Connect your broadband internet connection
to the wireless router’s WAN port.
4.
Connect the Computer LAN cable.
5
ADSL / Cable
Modem
5.
Plug in the Power Adapter.
6.
Wait until the Power light remains on.
This means the router is ready for use.
7.
Power back on your ADSL / Cable modem by plugging in the
power adapter.
8.
Installation is now complete. You can now begin to
configure the device.
6
Check Your Network Settings
(Windows XP / Vista)
1.
Click the Start Button and open Control Panel.
Windows XP
2.
Windows Vista
Windows XP, double click
Network Connections
Windows Vista, click
View Network Status and Tasks
then Manage Network Connections
7
3.
Right click on Local Area
Connection and choose
Properties.
Note: The name could be
different due to different
Network Interfaces.
4.
Check the Client for Microsoft Networks, File and Printer
Sharing, and Internet Protocol (TCP/IP) is ticked. If not,
please tick them.
8
5.
Select Internet Protocol (TCP/IP) and
click [Properties]
6.
Select these two options and click [OK].
9
Configuration
1. Shutdown and restart your computer.
2. Once restart is completed, start your WEB browser (Internet
Explorer recommended).
In the Address box, enter the following:
http://192.168.0.1
3.
Enter the Username and Password when prompted.
Defaults
Username: admin
Password: password
10
4.
You can select the language on Wizard to setup step by step
5.
You also can click on the left menu for language selection.
6.
Please have your Internet Service
Provider’s Username, Password
and other connection details
ready.
Then follow the steps of the
wizard to complete the setup.
11
7.
You can set your Wireless network name (SSID) and
security encryption.
12
8.
LevelOne recommends WPA2-PSK AES for maximum
wireless security. Please ensure that the same network
security settings are used on both the router and wireless
client.
Please type your passkey in the PSK field.
13
Troubleshooting
1. I cannot connect to the wireless router to start
configuration.
Check that you have connected the cable correctly between
the router’s LAN port and your computer. Also check if your
computer is set to obtain an IP Address via DHCP (see above).
2. I cannot connect to the Internet.
Try to turn off the router and your ADSL/Cable modem. Wait 30
seconds and then turn the devices back on. If you still have
problems, then access the router’s configuration page and
check whether the router has obtained an Internet IP Address
in the Status page.
If the above does not work, please contact your Internet
Service Provider to check whether there are any problems with
the connection or settings.
14
3. I cannot connect to the wireless network.
Check whether the SSID network name and wireless security
are the same on both the client and router. If you still have
problems, then power off and on your router and restart your
computer.
Your last solution will be forced to reset the router to factory
default settings.
Make sure your router’s Power light is not blinking and remains
ON. Then press and hold the WPS and WLAN buttons for more
than 10 seconds until you see the Power light blink 2 times,
then release the buttons. The router is now reset to factory
defaults.
15