PRODUCT SPECIFICATION Part Number PLC764-WCW04 Details • • • • Features Piranha LED 7.62 x 7.62 x 9.4mm Emitting Color White InGaN Dice Used • • • • 3mm Lens High Luminous Output High Current Operation RoHS Compliant Mechanical Dimensions Notes: 1. Dimensions in millimeters [inch], and tolerance is ±0.25 [.010] unless otherwise noted. 2. Specifications subject to change without notice www.p-tec.net 100814 Rev0 JAS Page 1 of 7 Device Selection Guide Chip Model Number Material InGaN PLC764-WCW04 Emitting Color White Absolute Maximum Ratings at Ta=25°C Parameter Symbol Power Dissipation Continuous Forward Current Peak Current (duty cycle 1/10, 1KHz) Reverse Voltage Operating Temperature Storage Temperature Soldering Conditions PAD IAF IPF VR Topr Tstg Rating W 266 70 100 5 -40~+80 -40~+100 Unit mW mA mA V °C °C Max. 260℃ for 5 sec Max.(3mm from the epoxy body) Electrical and Optical Characteristics at Ta=25°C Parameter Forward Voltage Luminous Flux Chromacity Coordinates Viewing Angle Reverse Current www.p-tec.net Symbol VF Iv X/Y 2θ1/2 IR Min. -6000 ---- Typ. 3.3 8500 0.31/0.32 50 -- 100814 Rev0 JAS Max. 3.8 ---10 Unit V mlm nm deg μA Condition IF=30mA VR=5V Page 2 of 7 Luminous Flux Rank Limits ( IF = 30mA ) Code K L M N Unit: mlm Min. Max. 6000 7000 7000 8000 8000 10000 10000 12000 Color Rank Limits ( IF = 30mA ) www.p-tec.net 100814 Rev0 JAS Page 3 of 7 Forward Voltage Rank Limits ( IF = 30mA ) Code H J K L M Unit: V Min. Max. 2.8 3.0 3.0 3.2 3.2 3.4 3.4 3.6 3.6 3.8 Notes: 1. Tolerance of measurement of luminous Flux: ±15% 2. Tolerance of measurement of Dominant wavelength: ±2nm 3. Tolerance of measurement of forward voltage: ±0.05v 4. All data measured by P-tec’s test equipment 5. One delivery will include several color rank, VF and Iv ranks of the products. 6. The quantity-ratio of the ranks is decided by P-tec 7. Please confirm with P-tec salesman, if your request differs from standard specifications. www.p-tec.net 100814 Rev0 JAS Page 4 of 7 Typical Electrical/Optical Characteristic Curves • Ta=25°C Unless Otherwise Noted www.p-tec.net 100814 Rev0 JAS Page 5 of 7 Precautions for Use 1. Recommended soldering conditions 1.1. Wave soldering 1.2. Recommended Soldering: Power dissipation of iron should be smaller than 15W and temperature should be controllable. Soldering temperature should be under 230, time 3sec. 2. Static Electricity 2.1 Static electricity or surge voltage damages LEDs. It is recommended that a wrist band or an anti-electrostatic glove be used when handling the LEDs. 2.2 All devices, equipment and machinery must be properly grounded. It is recommended that measures be taken against surge voltage to the equipment that mounts the LEDs. www.p-tec.net 100814 Rev0 JAS Page 6 of 7 Approved By Checked By Prepared By Customer Approval Signatures Rev. 0 www.p-tec.net Record Of Revisions Comments Released Spec 100814 Rev0 JAS Page -- Date 10/08/14 Page 7 of 7