Series 282 Data Sheet ® Electrocomponents Precision Potentiometer Industrial 16mm Size Conductive Plastic Precision Rotary Sensor Features • Robust Construction • 2 Million Cycle Life • 2% Precision Linearity • Water Resistant (IP54, IP67) • Wide Temperature Range • Solder Lug, Faston, PC Terminal • Continuous Rotation Available • RoHS Compliant Electrical and Mechanical Specifications Resistance Range 1 K through 500 K ohms, linear Consult CTS for audio taper Resistance Tolerance ± 10%, ± 20% Linearity ± 2% Dielectric Strength 750 VDC for 1 minute Maximum Operating Voltage 500 VDC Insulation Resistance 1000 Megohms minimum @ 500 VDC (Refer to Resistance Tapers for detail) Rotational Torque 3 – 50 gf-cm Mounting Information Bushing Mount Rotational L ife 2 M cycles Power Rating 0.25 watts @ 55°C Angle of Rotation 250°, 300°, 360° Push-Pull Strength of Shaft 13.6 kg for 10 seconds Temperature Operating: -40°C to 125°C Storage: -55°C to 150°C Solder Heat Resistance 350°C for 5 seconds Ingress Protection Rating IP54, IP67 Vibration 15G, 10 to 2000 Hz Stop Strength 9 kgf-cm minimum 1-4 CTS Electrocomponents © 2013 CTS Corporation. All rights reserved. Information subject to change. 12/5/13 www.ctscorp.com 282S Metal Shaft, Bushing Mount, Solder Lug (Faston) Terminal Formed to Rear DIMENSION : mm STANDARD TOLERANCE : .X (1 PLACE) : ±0.3 .XX(2 PLACE): ±0.13 282U Metal Shaft, Bushing Mount, PC Terminal Formed to Front 15.9 M9 X .75P or 3/8”-32 UNEF 2.5±0.2 “G” See “Shaft Trim Options” Ø2.8±0.2 1.0±0.1 17.4 T2 T1 CTS 4.3 1.6±0.2 1 2 3 3.2 G “L”±0.4 +0.2 Ø3.0-0 Locating Lug “G” Thickness “T1” Thickness “T2” 8 mm 9.4 mm 4.1 mm 10 mm 9.8 mm 4.5 mm CCW DIMENSION : mm STANDARD TOLERANCE : .X (1 PLACE) : ±0.3 .XX(2 PLACE): ±0.13 C CLEARANCE HOLE 16.25±0.05 WIPER 3 1 CLOCKWISE CIRCUIT 0.8 C +0.2 Ø1.2-0 (3) 2 2-4 CTS Electrocomponents 13.9 16.25 “A“ CW 6.00 6.00 ±0.05 ±0.05 PCB LAYOUT OPPOSITE COMPONENT SIDE © 2013 CTS Corporation. All rights reserved. Information subject to change. 12/5/13 www.ctscorp.com 282T Metal Shaft, Bushing Mount, Solder Lug (Faston) Terminal DIMENSION : mm STANDARD TOLERANCE : .X (1 PLACE) : ±0.3 .XX(2 PLACE): ±0.13 Shaft Trim Options ROUND X FLATTED Shaft Trim Diameter R .236” (6.00 mm) O .250” (6.35 mm) Shaft Trim Y Y X X KNURLED & SLOTTED Y X Y F .236” (6.00 mm) .375” (9.52 mm) .156” (3.96 mm) L .250” (6.35 mm) .440” (11.18 mm) .217” (5.50 mm) Shaft Trim SD SLOT Diameter Diameter X Y S .236” (6.00 mm) .063” (1.6mm) .039” (1.0mm) D .250” (6.35 mm) .063“ (1.6mm) .039“ (1.0mm) Shaft Trim K Diameter X Y .236” (6.00 mm) .344” (8.74 mm) .063” (1.60 mm) Z 24 Teeth Z 3-4 CTS Electrocomponents © 2013 CTS Corporation. All rights reserved. Information subject to change. 12/5/13 www.ctscorp.com PERCENT RESISTANCE PERCENT RESISTANCE PERCENT RESISTANCE Resistance Tapers TOTAL ROTATIONAL ANGLE TOTAL ROTATIONAL ANGLE TOTAL ROTATIONAL ANGLE: 250 TOTAL ROTATIONAL ANGLE TOTAL ROTATIONAL ANGLE: 300° TOTAL ROTATIONAL ANGLE: 360° Ordering Information 282 T TERMINAL STYLE T- Solder Lug(Faston) S- Solder Lug Formed to Rear U- PC Terminals Formed to Front A A SHAFT LENGTH “L” Examples: mm inch A - 10 mm 1 - .625” B - 15 mm 2 - .750” C - 20 mm 3 - .875” D - 25 mm 4 - 1.000” E - 30 mm 5 - 1.125” 103 R RESISTANCE CODE EXAMPLES CODE 102 103 503 104 504 Note: Incremental length : 5mm or .125” BUSHING MOUNT ”A” Bushing Length mm inch A - 5.0 mm 2 - .250” B - 7.5 mm 3 - .375” C - 10.0 mm 4 - .500” Notes: Incremental Length : 2.5mm or .125” Bushing Dia. & Thread: M9 X .75P (metric) 3/8” - 32 UNEF (imperial) A SHAFT TRIM OPTIONS Shaft Diameter 6mm (.236”) *R - Round F - Flatted .375” X .156” K - Knurled 24 Teeth S - SD Slot .039”W X .063” D Shaft Diameter 6.35mm (.250”) *O - Round L - Flatted .440” X .217” D - SD Slot .039” W X .063” D 2 5 B 1 LINEARITY 2 - ± 2% RESISTANCE 1K 10K 50K 100K 500K LOCATING LUG “G” 1 - Left, 10mm 2 - Left, 8mm 3 - No Lug IP Rating 5 - IP54 6 - IP67 RESIST TOL A - ± 10% B - ± 20% ROTATION ANGLE ABC- Total 250° 300° 360° Effective 240° 280° 340 Notes: *Round shafts are not applicable for 360° rotational angle option. Please consult factory for other mounting options or custom features not listed. Standard Part - 282T33L502A25A2, 282T33L502A25C2, 282TCBS103A25B1 282T33L502A26A2, 282T33L502A26C2, 282TCBS103A26B1 4 -4 CTS Electrocomponents © 2013 CTS Corporation. All rights reserved. Information subject to change. 12/5/13 www.ctscorp.com