VCS943 High Kv, 9x14mm VCSO APPLICATIONS Frequency Translation and Jitter Attenuation SONET/SDH 10 GbE WiMAX Base Stations/Picocells DAC clocking FEATURES • • • • • • • • • • High Tuning Gain Transfer Industry Standard 9x14mm SMT Footprint +3.3 Vdc Supply Voltage -40°C to 85°C Temp. Range LVPECL differential outputs ± 50ppm Absolute Pull Range (APR) Output Enable/Disable Function SAW filter design Extremely Low Jitter DESCRIPTION Surface mount 9x14mm VCSO operating at 3.3V supply with complementary LVPECL outputs for use in datacom, telecom, and DAC clock applications. ELECTRICAL SPECIFICATIONS Parameter Operating Conditions Min Typical Max Unit 600 622.08, 644.5313, 666.514, 669.3266 693.483, 768 1000 MHz Operating Temperature Range -40 - 85 °C Storage Temperature Range -55 - 125 °C Nominal Frequency Conditions & Remarks fNOM Supply Voltage VCC; ±5% 3.135 3.300 3.465 Vdc Supply Current Icc; Max. VCC; TA = 25°C load = 50Ω to VCC – 2V - 65 75 mA Load output to VCC -2V - 50 - Ω ref to TA = 25°C; VC = constant - +20 -160 - ppm Frequency Stability Frequency vs. Temperature Electronic Frequency Control Input Impedance Zi 50 100 - kΩ Control Voltage Range VC ; positive monotonic transfer 0.3 - 3.0 Vdc Gain Transfer Kv - 350 - ppm/V Absolute Pull Range APR; all causes (see Note 1) ± 50 - - ppm Modulation Bandwidth -3dB ref. 100Hz - 500 - kHz Linearity Deviation from best linear fit - ±4 ±10 % NOTE 1: Minimum guaranteed frequency shift (∆f/fNOM) under all conditions (temperature, aging, supply voltage, load) for 15 years at an average effective operating temperature of +55°C ELECTRICAL SPECIFICATIONS (Continued) Document No. VCS943 Data Sheet Page 1 - 5 Rev. X1 ٠ ٠ ٠ CTS Electronic Components, Inc. ٠ 171 Covington Drive ٠ Bloomingdale, IL 60108 ٠ ٠ ٠ ٠ ٠ ٠ www.ctscorp.com ٠ ٠ ٠ VCS943 High Kv, 9x14mm VCSO Parameter Output Parameters Conditions & Remarks Min Output Signal Rise/Fall Times 20% to 80% Duty Cycle @ 50% of output signal Start up time to reach 90% of final amplitude Phase Jitter Unit VOL - - VCC-1.620 VOH VCC-1.025 - - Vdc - 250 400 ps 45 50 55 % - - 10 ms 100Hz - -85 - dBc/Hz 1kHz - -110 - dBc/Hz 10kHz - -140 - dBc/Hz 100kHz - -143 - dBc/Hz 1MHz - -143 - dBc/Hz 12kHz to 20MHz (calculated from 622 MHz Phase Noise) - 0.10 0.25 ps RMS 50kHz to 80MHz (calculated from 622 MHz Phase Noise) - 0.10 0.25 ps RMS Typical for 622.08 MHz LVPECL OUTPUT WAVEFORM Pad 2 Low ”0” Open High ”1” Max LVPECL Amplitude Phase Noise Typical TEST CIRCUIT, LVPECL LOAD OUTPUT ENABLE/DISABLE LOGIC Pad 4 outputs disabled PECL Low outputs enabled Output outputs enabled Output Document No. VCS943 Data Sheet Page 2 - 5 Pad 5 PECL High Comp. Output Comp. Output Rev. X1 ٠ ٠ ٠ CTS Electronic Components, Inc. ٠ 171 Covington Drive ٠ Bloomingdale, IL 60108 ٠ ٠ ٠ ٠ ٠ ٠ www.ctscorp.com ٠ ٠ ٠ VCS943 High Kv, 9x14mm VCSO MECHANICAL SPECIFICATIONS PACKAGE DRAWING 14.2 MAX [.559] Pin 5 Date Code Pin 4 VCS943 622M0800 CTS LLLLL-RR YYWW Pin 6 Lot Code Pin 1 Pin 2 Pin 1 2 3 4 5 6 9.1 [.358] MAX Pin 3 Pin #1 Mark Function Control Voltage - Vc Enable/Disable Control Ground/Case Output Complementary Output Supply Voltage - Vcc 3.00 [.118] MAX 5.08 [.200] Ø0.64 [.025] TYP 2.54 [.100] 1.15 TYP [.045] Pin 1 5.59 [.220] Exposed Ground plane and cover castelation area. 2 places Pin 3 3.30 TYP [.130] 4.17 [.164] Pin 6 Pin 4 Ground plane .76 [.030] 1.02 [.040] Hatching indicates barrier covering over resist mask over ground plane. Solder resist mask All dimensions are in MM [Inches]. All dimensions are Nominal unless otherwise specified. Lead Termination Finish: Gold Flash, <10 micro inch, over Ni plated Cu. Lead Termination Finish: Gold flash, <10 micro inch, over 100 micro inch minimum Ni plated Cu Co-Planarity (from seating plane): 0.1 [0.004] maximum Dimensions in mm and [inches] PAD FUNCTION 1 - Control Voltage - VC 2 - Enable/Disable Control 3 - Ground/Case 4 - Output 5 - Complementary Output 6 - Supply Voltage - VCC Document No. VCS943 Data Sheet Page 3 - 5 Rev. X1 ٠ ٠ ٠ CTS Electronic Components, Inc. ٠ 171 Covington Drive ٠ Bloomingdale, IL 60108 ٠ ٠ ٠ ٠ ٠ ٠ www.ctscorp.com ٠ ٠ ٠ VCS943 High Kv, 9x14mm VCSO SUGGESTED SOLDER PAD GEOMETRY 5.08 [.200] 2.54 [.100] 5.33 [.210] 9.86 [.388] 1.27 [.050] Dimensions are in mm and [inches]. MAXIMUM SOLDERING PROFILE Temperature 217°C 260°C (Absolute max temperature) Time 60-150 sec 10 sec. max Note: Part is not designed to be reflowed in an inverted position. TAPE AND REEL INFORMATION 24.4 2.4 Ø 13 Ø1.50 5.10 4.00 12.00 120° 1.75 11.50 VCS943 622M0800 CTS LLLLL-RR YYWW 14.80 VCS943 622M0800 CTS LLLLL-RR YYWW 9.80 Ø 100 24.00 DIMENSIONS ARE IN MM Ø 21.2 DIRECTION OF FEED Device quantity is 1000 pieces max. per 330mm reel. Document No. VCS943 Data Sheet Page 4 - 5 Rev. X1 ٠ ٠ ٠ CTS Electronic Components, Inc. ٠ 171 Covington Drive ٠ Bloomingdale, IL 60108 ٠ ٠ ٠ ٠ ٠ ٠ www.ctscorp.com ٠ ٠ ٠ Ø 330 VCS943 High Kv, 9x14mm VCSO ENVIRONMENTAL SPECIFICATIONS This product is capable of operating within the following environmental conditions: Operating Temperature Storage Temperature Humidity Atmospheric Pressure Moisture Sensitivity RoHS -40 to +85 °C -55 to 125°C 95% Relative humidity max @ 40°C 730 to 780 mm Hg Level 1 Fully compliant to RoHS Directive 2002/95/EC Model 943 Part Number Generator: Frequency in MHz (“M” = decimal point) VCS943 - _ _ _M_ _ _ _ P/N example: VCS943-622M0800 Document No. VCS943 Data Sheet Page 5 - 5 Rev. X1 ٠ ٠ ٠ CTS Electronic Components, Inc. ٠ 171 Covington Drive ٠ Bloomingdale, IL 60108 ٠ ٠ ٠ ٠ ٠ ٠ www.ctscorp.com ٠ ٠ ٠