VCO/ PLL Module Data Sheet: VCP1016A Application : UCR850 RF Tx LO synthesizer module 1.0 DESCRIPTION AND APPLICATION VCO/ PLL module with Analog Devices ADF4113 PLL IC. 2.0 ELECTRICAL SPECIFICATIONS All parameters are specified at 25 degrees C and 5.0 VDC with output load impedance of 50 ohms. Specification Min Typ Max Units 2.1 Supply Voltage 4.75 5.00 5.25 V DC 2.2 Current Drain (VCO plus PLL) 35 50 mA 2.3 RF frequency 1220.37 MHz 2.4 Step size 2.5 Lock monitor: locked 2.6 Lock monitor: unlocked 2.7 Lock time 2.8 Operating Temperature 2.9 RMS phase jitter (100 Hz – 1 MHz B/W) 2.10 Phase Noise.... 2.10.1 Phase noise @ 100 Hz offset 2.10.2 Phase noise @ 1 kHz offset 2.10.3 Phase noise @ 10 kHz offset 2.10.4 Phase noise @ 100 kHz offset 2.10.5 Phase noise @ 1 MHz offset 1195.41 30 CMOS/TTL high = locked kHz 2.5 5.0 V 0 0.5 V 40 msec 85 deg C 1.5 deg rms -10 1 -140 dBc/Hz dBc/Hz dBc/Hz dBc/Hz dBc/Hz -75 2.11 2nd Harmonic suppression -20 dBc 2.12 3rd Harmonic suppression -20 dBc 2.13 Output power 3 dBm 2.14 Spurious performance (offset < 4 MHz) -70 dBc 2.15 Spurious performance (offset > 4 MHz) -80 dBc 2.16 Note: reference oscillator 2.17 Note: reference amplitude CMOS load 2.18 Output impedance 2.19 Programming -3 0 15 0.8 MHz 1.2 50 V ptp ohms 3-wire serial 5V CMOS ADF4113 PLL IC I word: 438093 hex. R word: 7D0 hex. Rev. “0” 1/2/03 VCO/ PLL Module Data Sheet: VCP1016A Application : UCR850 RF Tx LO synthesizer module 3.0 MECHANICAL CHARACTERISTICS 3.1 Pkg. size is 10.5 x 14 mm x 2.9 mm (max.). Pinouts: 1] VCC (PLL) 2] GND 3] REF Input 4] GND 5] VCC (VCO) 6] GND 7 ] RF Output 8 ] GND 9 ] Lock Detect 10] Clock 11] Data 12] Load Enable 13] ,14] Gnd Rev. “0” 1/2/03 VCO/ PLL Module Data Sheet: VCP1016A Application : UCR850 RF Tx LO synthesizer module 4.0 STANDARD ENVIRONMENTAL LIMITS This product is capable of operating within the following environmental conditions: 4.1 Operating Temperature 4.2 Storage Temperature 4.3 Humidity 4.4 Atmospheric Pressure 4.5 Vibration 4.6 Shock -10 to +85 °C. -40 to +90 °C. 95% Relative humidity max @ 40°C. 730 to 780 mm Hg. 10 to 60 cps with double amplitude of 1.52mm max. (1/2 hour in each of 3 perpendicluar planes). 1/2 sine pulse, 7000G, with pulse width 0.3mSec. (1 shock in each of 6 directions of 3 perpendiclar planes). 5.0 MAXIMUM SOLDERING PROFILE Temperature 110 to150 °C >183°C Time 6min 2.5min >235°C 0.25min 240°C Max temperature Rev. “0” 1/2/03