VCO/ PLL Module Data Sheet: VCP1025A Application : Cellular / PCS Rx IF 1.0 DESCRIPTION AND APPLICATION VCO/ PLL module with Analog Devices ADF4113 PLL IC. 2.0 ELECTRICAL SPECIFICATIONS All parameters are specified at 25 degrees C and 5.0 VDC with output load impedance of 50 ohms. Specification Min Typ Max Units 2.1 Supply Voltage (VCO & PLL) 4.75 5.00 5.25 V DC 2.2 VCO Current Drain 11 14 mA 2.3 PLL Current Drain 13 16 mA 2.4 RF frequency 255.36 2.5 Phase jitter (100 Hz to 1 MHz) 0.2 2.6 Operating Temperature 2.7 Phase Noise.... 2.7.1 Phase noise @ 100 Hz offset 2.7.2 Phase noise @ 1 kHz offset 2.7.3 Phase noise @ 10 kHz offset 2.7.4 Phase noise @ 100 kHz offset 2.7.5 Phase noise @ 1 MHz offset 2.8 2nd Harmonic suppression 2.9 Output power 2.10 Spurious performance 2.11 Lock detector voltage: Out-of-lock In-lock 2.12 Note: reference oscillator Comparison freq. = 0.96 MHz 2.13 Note: reference amplitude -10 -80 -88 -110 -130 -150 -2.5 -85 0 2.5 MHz 0.3 deg rms 85 deg C -75 -85 -105 -125 -145 dBc/Hz dBc/Hz dBc/Hz dBc/Hz dBc/Hz -20 dBc 2.0 dBm 80 dBc 0.5 5.0 V V 30.72 0.5 MHz 2.0 V ptp Rev. “0” 2/3/03 VCO/ PLL Module Data Sheet: VCP1025A Application : Cellular / PCS Rx IF 3.0 MECHANICAL CHARACTERISTICS 3.1 Pkg. size is 10.5 x 14 mm x 2.9 mm (max.). Pinouts: 1] VCC (PLL) 2] GND 3] REF Input 4] GND 5] VCC (VCO) 6] GND 7 ] RF Output 8 ] GND 9 ] Lock Detect 10] Clock 11] Data 12] Load Enable 13] ,14] Gnd Rev. “0” 2/3/03 VCO/ PLL Module Data Sheet: VCP1025A Application : Cellular / PCS Rx IF 3.2 Recommended pad layout: Rev. “0” 2/3/03 VCO/ PLL Module Data Sheet: VCP1025A Application : Cellular / PCS Rx IF 4.0 STANDARD ENVIRONMENTAL LIMITS This product is capable of operating within the following environmental conditions: 4.1 Operating Temperature 4.2 Storage Temperature 4.3 Humidity 4.4 Atmospheric Pressure 4.5 Vibration 4.6 Shock -10 to +85 °C. -40 to +90 °C. 95% Relative humidity max @ 40°C. 730 to 780 mm Hg. 10 to 60 cps with double amplitude of 1.52mm max. (1/2 hour in each of 3 perpendicluar planes). 1/2 sine pulse, 7000G, with pulse width 0.3mSec. (1 shock in each of 6 directions of 3 perpendiclar planes). 5.0 MAXIMUM SOLDERING PROFILE Temperature 110 to150 °C >183°C Time 6min 2.5min >235°C 0.25min 240°C Max temperature Rev. “0” 2/3/03