Document No.: FT_000052 FT245R USB FIFO IC Datasheet Version 2.13 Clearance No.: FTDI# 39 Future Technology Devices International Ltd. FT245R USB FIFO IC The FT245R is a USB to parallel FIFO interface with the following advanced features: Single chip USB to parallel FIFO bidirectional data transfer interface. Entire USB protocol handled on the chip. No USB specific firmware programming required. Fully integrated 1024 bit EEPROM storing device descriptors and FIFO I/O configuration. Fully integrated USB termination resistors. Fully integrated clock generation with no external crystal required. Data transfer rates up to 1Mbyte / second. 128 byte receive buffer and 256 byte transmit buffer utilising buffer smoothing technology to allow for high data throughput. FTDI’s royalty-free Virtual Com Port (VCP) and Direct (D2XX) drivers eliminate the requirement for USB driver development in most cases. Device supplied pre-programmed with unique USB serial number. Supports bus powered, self powered and high-power bus powered USB configurations. Integrated +3.3V level converter for USB I/O. Integrated level converter on FIFO interface for interfacing to external logic running at between +1.8V and +5V. True 5V/3.3V/2.8V/1.8V CMOS drive output and TTL input. Configurable I/O pin output drive strength. Integrated power-on-reset circuit. Fully integrated AVCC supply filtering - no external filtering required. +3.3V (using external oscillator) to +5.25V (using internal oscillator) Single Supply Operation. Low operating and USB suspend current. Low USB bandwidth consumption. UHCI/OHCI/EHCI host controller compatible. Unique USB FTDIChip-ID™ feature. USB 2.0 Full Speed compatible. Configurable FIFO interface I/O pins. Synchronous and asynchronous bit bang interface options. -40°C to 85°C extended operating temperature range. Available in compact Pb-free 28 Pin SSOP and QFN32 packages (both RoHS compliant). Neither the whole nor any part of the information contained in, or the product described in this manual, may be adapted or reproduced in any material or electronic form without the prior written consent of the copyright holder. This product and its documentation are supplied on an as-is basis and no warranty as to their suitability for any particular purpose is either made or implied. Future Technology Devices International Ltd will not accept any claim for damages howsoever arising as a result of use or failure of this product. Your statutory rights are not affected. This product or any variant of it is not intended for use in any medical appliance, device or system in which the failure of the product might reasonably be expected to result in personal injury. This document provides preliminary information that may be subject to change without notice. No freedom to use patents or other intellectual property rights is implied by the publication of this document. Future Technology Devices International Ltd, Unit 1, 2 Seaward Place, Centurion Business Park, Glasgow G41 1HH United Kingdom. Scotland Registered Company Number: SC136640 Copyright © 2010 Future Technology Devices International Limited 1 Document No.: FT_000052 FT245R USB FIFO IC Datasheet Version 2.13 Clearance No.: FTDI# 39 1 Typical Applications Upgrading Legacy Peripherals to USB USB Industrial Control Cellular and Cordless Phone USB data transfer cables and interfaces USB MP3 Player Interface Interfacing MCU/PLD/FPGA based designs to USB USB FLASH Card Reader and Writers Set Top Box PC - USB interface USB Audio and Low Bandwidth Video data transfer USB Digital Camera Interface USB Hardware Modems PDA to USB data transfer USB Wireless Modems USB Smart Card Readers USB Bar Code Readers USB Instrumentation USB Software and Hardware Encryption Dongles 1.1 Driver Support Royalty free VIRTUAL COM PORT (VCP) DRIVERS for... Royalty free D2XX Direct Drivers (USB Drivers + DLL S/W Interface) Windows 7 32,64-bit Windows 7 32,64-bit Windows XP and XP 64-bit Windows XP and XP 64-bit Windows Vista and Vista 64-bit Windows Vista and Vista 64-bit Windows XP Embedded Windows XP Embedded Windows 98, 98SE, ME, 2000, Server 2003, XP and Server 2008 Windows 98, 98SE, ME, 2000, Server 2003, XP and Server 2008 Windows CE 4.2, 5.0 and 6.0 Windows CE 4.2, 5.0 and 6.0 Mac OS 8/9, OS-X Linux 2.4 and greater Linux 2.4 and greater The drivers listed above are all available to download for free from FTDI website (www.ftdichip.com). Various 3rd party drivers are also available for other operating systems - see FTDI website (www.ftdichip.com) for details. For driver installation, please refer to the application note AN232B-10. For driver installation, please refer to http://www.ftdichip.com/Documents/InstallGuides.htm 1.2 Part Numbers Part Number Package FT245RQ-xxxx 32 Pin QFN FT245RL-xxxx 28 Pin SSOP Note: Packaging codes for xxx is: -Reel: Taped and Reel, (SSOP is 2,000pcs per reel, QFN is 6,000pcs per reel). - Tube: Tube packing, 47pcs per tube (SSOP only) - Tray: Tray packing, 490pcs per tray (QFN only) For example: FT245RQ-Reel is 6,000pcs taped and reel packing Copyright © 2010 Future Technology Devices International Limited 2 Document No.: FT_000052 FT245R USB FIFO IC Datasheet Version 2.13 Clearance No.: FTDI# 39 1.3 USB Compliant The FT245R is fully compliant with the USB 2.0 specification and has been given the USB-IF Test-ID (TID) 40680005 (Rev B) and 40770019 (Rev C). Copyright © 2010 Future Technology Devices International Limited 3 Document No.: FT_000052 FT245R USB FIFO IC Datasheet Version 2.13 Clearance No.: FTDI# 39 2 FT245R Block Diagram VCC PWREN# 3V3OUT USBDP USBDM 3.3 Volt LDO Regulator USB Transceiver with Integrated Series Resistors and 1.5K Pull-up VCCIO FIFO RX Buffer 128 bytes Serial Interface Engine ( SIE ) FIFO Controller with Programmable High Drive USB Protocol Engine To USB Transceiver Cell D0 D1 D2 D3 D4 D5 D6 D7 RD# WR RXF# TXE# Internal EEPROM USB DPLL 3V3OUT FIFO TX Buffer 256 bytes OSCO (optional) OCSI (optional) Internal 12MHz Oscillator 48MHz Clock Multiplier RESET# RESET GENERATOR To USB Transceiver Cell TEST GND Figure 2.1 FT245R Block Diagram For a description of each function please refer to Section 4. Copyright © 2010 Future Technology Devices International Limited 4 Document No.: FT_000052 FT245R USB FIFO IC Datasheet Version 2.13 Clearance No.: FTDI# 39 Table of Contents 1 Typical Applications ........................................................................ 2 1.1 Driver Support .................................................................................... 2 1.2 Part Numbers...................................................................................... 2 1.3 USB Compliant .................................................................................... 3 2 FT245R Block Diagram .................................................................... 4 3 Device Pin Out and Signal Description ............................................ 7 4 5 6 7 3.1 28-LD SSOP Package .......................................................................... 7 3.2 SSOP Package Pin Out Description...................................................... 7 3.3 QFN-32 Package ............................................................................... 10 3.4 QFN-32 Package Signal Description .................................................. 10 3.5 FT245R FIFO READ Timing Diagrams ................................................ 13 3.6 FT245R FIFO WRITE Timing Diagrams .............................................. 14 Function Description ..................................................................... 15 4.1 Key Features ..................................................................................... 15 4.2 Functional Block Descriptions ........................................................... 16 Devices Characteristics and Ratings.............................................. 17 5.1 Absolute Maximum Ratings............................................................... 17 5.2 DC Characteristics............................................................................. 18 5.3 EEPROM Reliability Characteristics ................................................... 21 5.4 Internal Clock Characteristics ........................................................... 21 5.5 Thermal Characteristics .................................................................... 22 USB Power Configurations ............................................................ 23 6.1 USB Bus Powered Configuration ...................................................... 23 6.2 Self Powered Configuration .............................................................. 24 6.3 USB Bus Powered with Power Switching Configuration .................... 25 6.4 USB Bus Powered with Selectable External Logic Supply .................. 26 Application Examples .................................................................... 27 7.1 USB to MCU FIFO Interface ............................................................... 27 7.2 Using the External Oscillator ............................................................ 28 8 Internal EEPROM Configuration .................................................... 29 9 Package Parameters ..................................................................... 30 9.1 SSOP-28 Package Dimensions .......................................................... 30 9.2 QFN-32 Package Dimensions ............................................................ 31 9.3 QFN-32 Package Typical Pad Layout ................................................. 32 9.4 QFN-32 Package Typical Solder Paste Diagram ................................. 32 Copyright © 2010 Future Technology Devices International Limited 5 Document No.: FT_000052 FT245R USB FIFO IC Datasheet Version 2.13 Clearance No.: FTDI# 39 9.5 Solder Reflow Profile ........................................................................ 33 10 Alternative Parts ........................................................................ 34 11 Contact Information ................................................................... 35 Appendix A - References ............................................................................ 36 Appendix B - List of Figures and Tables ..................................................... 37 Appendix C - Revision History .................................................................... 39 Copyright © 2010 Future Technology Devices International Limited 6 Document No.: FT_000052 FT245R USB FIFO IC Datasheet Version 2.13 Clearance No.: FTDI# 39 3 Device Pin Out and Signal Description 3.1 28-LD SSOP Package 4 D0 28 1 NC D5 D6 D3 PWREN# RD# WR 14 D0 VCC OSCI 16 TEST 15 USBDM D2 USBDP D3 AGND FT245RL NC 8 FTDI GND FT245RL D7 YYXX-A XXXXXXXXXXXX D2 D1 VCCIO D1 D4 VCCIO OSCO 20 RXF# TXE# GND 24 27 28 VCC NC D5 RESET# NC D6 OSCI D7 OSCO RXF# RESET# GND 3V3OUT USBDM 15 19 USBDP D4 TXE# 17 3V3OUT A G N D 25 G N D 7 G N D 18 T E S T G N D 21 RD# WR PWREN# 1 5 3 11 2 9 10 6 23 22 13 14 12 26 Figure 3.1 SSOP Package Pin Out and Schematic Symbol 3.2 SSOP Package Pin Out Description Note: The convention used throughout this document for active low signals is the signal name followed by a# Pin No. Name Type Description 15 USBDP I/O USB Data Signal Plus, incorporating internal series resistor and 1.5kΩ pull up resistor to 3.3V. 16 USBDM I/O USB Data Signal Minus, incorporating internal series resistor. Table 3.1 USB Interface Group Copyright © 2010 Future Technology Devices International Limited 7 Document No.: FT_000052 FT245R USB FIFO IC Datasheet Version 2.13 Clearance No.: FTDI# 39 Pin No. Name Type Description 4 VCCIO PWR +1.8V to +5.25V supply to the FIFO Interface group pins (1...3, 5, 6, 9...14, 22, 23). In USB bus powered designs connect this pin to 3V3OUT pin to drive out at +3.3V levels, or connect to VCC to drive out at 5V CMOS level. This pin can also be supplied with an external +1.8V to +2.8V supply in order to drive outputs at lower levels. It should be noted that in this case this supply should originate from the same source as the supply to VCC. This means that in bus powered designs a regulator which is supplied by the +5V on the USB bus should be used. 7, 18, 21 GND PWR Device ground supply pins 17 3V3OUT Output +3.3V output from integrated LDO regulator. This pin should be decoupled to ground using a 100nF capacitor. The main use of this pin is to provide the internal +3.3V supply to the USB transceiver cell and the internal 1.5kΩ pull up resistor on USBDP. Up to 50mA can be drawn from this pin to power external logic if required. This pin can also be used to supply the VCCIO pin. 20 VCC PWR +3.3V to +5.25V supply to the device core. (see Note 1) 25 AGND PWR Device analogue ground supply for internal clock multiplier Table 3.2 Power and Ground Group Pin No. Name Type Description 8, 24 NC NC No internal connection 19 RESET# Input Active low reset pin. This can be used by an external device to reset the FT245R. If not required can be left unconnected, or pulled up to VCC. 26 TEST Input Puts the device into IC test mode. Must be tied to GND for normal operation, otherwise the device will appear to fail. 27 OSCI Input Input 12MHz Oscillator Cell. Optional – Can be left unconnected for normal operation. (see Note 2) 28 OSCO Output Output from 12MHZ Oscillator Cell. Optional – Can be left unconnected for normal operation if internal Oscillator is used. (see Note 2) Table 3.3 Miscellaneous Signal Group Pin No. Name Type Description 1 D0 I/O FIFO Data Bus Bit 0 2 D4 I/O FIFO Data Bus Bit 4 3 D2 I/O FIFO Data Bus Bit 2 5 D1 I/O FIFO Data Bus Bit 1 6 D7 I/O FIFO Data Bus Bit 7 9 D5 I/O FIFO Data Bus Bit 5 10 D6 I/O FIFO Data Bus Bit 6 Copyright © 2010 Future Technology Devices International Limited 8 Document No.: FT_000052 FT245R USB FIFO IC Datasheet Version 2.13 Clearance No.: FTDI# 39 Pin No. Name Type Description 11 D3 I/O FIFO Data Bus Bit 3 12 PWREN# Output Goes low after the device is configured by USB, then high during USB suspend. Can be used to control power to external logic P-Channel logic level MOSFET switch. Enable the interface pull-down option when using the PWREN# pin in this way. Should be pulled to VCCIO with 10kΩ resistor. 13 RD# Input Enables the current FIFO data byte on D0...D7 when low. Fetched the next FIFO data byte (if available) from the receive FIFO buffer when RD# goes from high to low. See Section 3.5 for timing diagram. 14 WR Input Writes the data byte on the D0...D7 pins into the transmit FIFO buffer when WR goes from high to low. See Section 3.6 for timing diagram. 22 TXE# Output When high, do not write data into the FIFO. When low, data can be written into the FIFO by strobing WR high, then low. During reset this signal pin is tri-state. See Section 3.6 for timing diagram. When high, do not read data from the FIFO. When low, there is data available in the FIFO which can be read by strobing RD# low, then high again. During reset this signal pin is tri-state. See Section 3.5 for timing diagram. 23 RXF Output If the Remote Wakeup option is enabled in the internal EEPROM, during USB suspend mode (PWREN# = 1) RXF# becomes an input. This can be used to wake up the USB host from suspend mode by strobing this pin low for a minimum of 20ms which will cause the device to request a resume on the USB bus. Table 3.4 FIFO Interface Group (see note 3) Notes: 1. The minimum operating voltage VCC must be +4.0V (could use VBUS=+5V) when using the internal clock generator. Operation at +3.3V is possible using an external crystal oscillator. 2. For details on how to use an external crystal, ceramic resonator, or oscillator with the FT245R, please refer Section 7.2 3. When used in Input Mode, the input pins are pulled to VCCIO via internal 200kΩ resistors. These pins can be programmed to gently pull low during USB suspend (PWREN# = “1”) by setting an option in the internal EEPROM. Copyright © 2010 Future Technology Devices International Limited 9 Document No.: FT_000052 FT245R USB FIFO IC Datasheet Version 2.13 Clearance No.: FTDI# 39 3.3 QFN-32 Package D7 Figure 3.2 QFN-32 Package Pin Out and schematic symbol 3.4 QFN-32 Package Signal Description Pin No. Name Type Description 14 USBDP I/O USB Data Signal Plus, incorporating internal series resistor and 1.5kΩ pull up resistor to +3.3V. 15 USBDM I/O USB Data Signal Minus, incorporating internal series resistor. Table 3.5 USB Interface Group Copyright © 2010 Future Technology Devices International Limited 10 Document No.: FT_000052 FT245R USB FIFO IC Datasheet Version 2.13 Clearance No.: FTDI# 39 Pin No. Name Type Description 1 VCCIO PWR +1.8V to +5.25V supply for the FIFO Interface group pins (2, 3, 6,7,8,9,10 11, 21, 22, 30,31,32). In USB bus powered designs connect this pin to 3V3OUT to drive out at +3.3V levels, or connect to VCC to drive out at +5V CMOS level. This pin can also be supplied with an external +1.8V to +2.8V supply in order to drive out at lower levels. It should be noted that in this case this supply should originate from the same source as the supply to VCC. This means that in bus powered designs a regulator which is supplied by the +5V on the USB bus should be used. 4, 17, 20 GND PWR Device ground supply pins. 16 3V3OUT Output +3.3V output from integrated LDO regulator. This pin should be decoupled to ground using a 100nF capacitor. The purpose of this output is to provide the internal +3.3V supply to the USB transceiver cell and the internal 1.5kΩ pull up resistor on USBDP. Up to 50mA can be drawn from this pin to power external logic if required. This pin can also be used to supply the VCCIO pin. 19 VCC PWR +3.3V to +5.25V supply to the device core. (see Note 1). 24 AGND PWR Device analogue ground supply for internal clock multiplier. Table 3.6 Power and Ground Group Pin No. Name Type Description 5, 12, 13, 23, 25, 29 NC NC No internal connection. Do not connect. 18 RESET# Input Active low reset. Can be used by an external device to reset the FT245R. If not required can be left unconnected, or pulled up to VCC. 26 TEST Input Puts the device into IC test mode. Must be tied to GND for normal operation, otherwise the device will appear to fail. 27 OSCI Input Input 12MHz Oscillator Cell. Optional – Can be left unconnected for normal operation. (see Note 2). 28 OSCO Output Output from 12MHZ Oscillator Cell. Optional – Can be left unconnected for normal operation if internal Oscillator is used. (see Note 2). Table 3.7 Miscellaneous Signal Group Pin Name Type Description 30 D0 I/O FIFO Data Bus Bit 0 31 D4 I/O FIFO Data Bus Bit 4 32 D2 I/O FIFO Data Bus Bit 2 2 D1 I/O FIFO Data Bus Bit 1 3 D7 I/O FIFO Data Bus Bit 7 No. Copyright © 2010 Future Technology Devices International Limited 11 Document No.: FT_000052 FT245R USB FIFO IC Datasheet Version 2.13 Clearance No.: FTDI# 39 Pin Name Type Description 6 D5 I/O FIFO Data Bus Bit 5 7 D6 I/O FIFO Data Bus Bit 6 8 D3 I/O FIFO Data Bus Bit 3 PWREN# Output Goes low after the device is configured by USB, then high during USB suspend. Can be used to control power to external logic P-Channel logic level MOSFET switch. Enable the interface pull-down option when using the PWREN# pin in this way. Should be pulled to VCCIO with 10kΩ resistors. RD# Input Enables the current FIFO data byte from D0…D7 when low. Fetched the next FIFO data byte (if available) from the receive FIFO buffer when RD# goes from high to low. See Section 3.5 for timing diagram. No. 9 10 11 WR Input Writes the data from byte from D0...D7 pins into the transmit FIFO buffer when WR goes from high to low. See section 3.6 for timing diagram. 21 TXE# Output When high, do not write data into the FIFO. When low, data can be written into the FIFO by strobing WR high, then low. During reset this signal pin is tri-state. See Section 3.6 for timing diagram. When high, do not read data from the FIFO. When low, there is data available in the FIFO which can be read by strobing RD# low, then high again. During reset this signal pin is tri-state. See Section 3.5 for timing diagram. 22 RXF# Output If the Remote Wakeup option is enabled in the internal EEPROM, during USB suspend mode (PWREN# = 1) RXF# becomes an input. This can be used to wake up the USB host from suspend mode by strobing this pin low for a minimum of 20ms which will cause the device to request a resume on the USB bus. Table 3.8 FIFO Interface Group (see note 3) Notes: 1. The minimum operating voltage VCC must be +4.0V (could use VBUS=+5V) when using the internal clock generator. Operation at +3.3V is possible using an external crystal oscillator. 2. For details on how to use an external crystal, ceramic resonator, or oscillator with the FT245R, please refer to Section 7.2 3. When used in Input Mode, the input pins are pulled to VCCIO via internal 200kΩ resistors. These pins can be programmed to gently pull low during USB suspend ( PWREN# = “1”) by setting an option in the internal EEPROM. Copyright © 2010 Future Technology Devices International Limited 12 Document No.: FT_000052 FT245R USB FIFO IC Datasheet Version 2.13 Clearance No.: FTDI# 39 3.5 FT245R FIFO READ Timing Diagrams T6 T5 RXF# T2 T1 RD# T4 T3 D[7...0] Valid Data Figure 3.3 FIFO Read Cycle Time Description Minimum Maximum Unit T1 RD# Active Pulse Width 50 - ns T2 RD# to RD# Pre-Charge Time 50 + T6 - ns T3 RD# Active to Valid Data* 20 50 ns T4 Valid Data Hold Time from RD# Inactive* 0 - ns T5 RD# Inactive to RXF# 0 25 ns T6 RXF# Inactive After RD Cycle 80 - ns Table 3.9 FIFO Read Cycle Timings *Load = 30pF Copyright © 2010 Future Technology Devices International Limited 13 Document No.: FT_000052 FT245R USB FIFO IC Datasheet Version 2.13 Clearance No.: FTDI# 39 3.6 FT245R FIFO WRITE Timing Diagrams T12 T11 TXE# T8 T7 WR T9 D[7...0] T10 Valid Data Figure 3.4 FIFO Write Cycle Time Description Minimum Maximum Unit T7 WR Active Pulse Width 50 - ns T8 WR to WR Pre-Charge Time 50 - ns T9 Valid data setup to WR falling edge* 20 - ns T10 Valid Data Hold Time from WR Inactive* 0 - ns T11 WR Inactive to TXE# 5 25 ns T12 TXE# Inactive After WR Cycle 80 - ns Table 3.10 FIFO Write Cycle *Load = 30pF Copyright © 2010 Future Technology Devices International Limited 14 Document No.: FT_000052 FT245R USB FIFO IC Datasheet Version 2.13 Clearance No.: FTDI# 39 4 Function Description The FT245R is a USB to parallel FIFO interface device which simplifies USB to FIFO designs and reduces external component count by fully integrating an external EEPROM, USB termination resistors and an integrated clock circuit which requires no external crystal, into the device. It has been designed to operate efficiently with a USB host controller by using as little as possible of the total USB bandwidth available. 4.1 Key Features Functional Integration. Fully integrated EEPROM, USB termination resistors, clock generation, AVCC filtering, power-on-reset (POR) and LDO regulator. Asynchronous Bit Bang Mode. In asynchronous bit-bang mode, the eight FIFO lines can be switched from the regular interface mode to an 8-bit general purpose I/O port. Data packets can be sent to the device and they will be sequentially sent to the interface at a rate controlled by an internal timer (equivalent to the baud rate pre-scaler. This option will be described more fully in a separate application note available from FTDI website (www.ftdichip.com). Synchronous Bit Bang Mode. The FT245R supports synchronous bit bang mode. This mode differs from asynchronous bit bang mode in that the interface pins are only read when the device is written to. This makes it easier for the controlling program to measure the response to an output stimulus as the data returned is synchronous to the output data. An application note, AN232R-01, available from FTDI website (www.ftdichip.com) describes this feature. FTDIChip-ID™. The FT245R also includes the new FTDIChip-ID™ security dongle feature. This FTDIChip-ID™ feature allows a unique number to be burnt into each device during manufacture. This number cannot be reprogrammed. This number is only readable over USB and forms a basis of a security dongle which can be used to protect any customer application software being copied. This allows the possibility of using the FT245R in a dongle for software licensing. Further to this, a renewable license scheme can be implemented based on the FTDIChip-ID™ number when encrypted with other information. This encrypted number can be stored in the user area of the FT245R internal EEPROM, and can be decrypted, then compared with the protected FTDIChip-ID™ to verify that a license is valid. Web based applications can be used to maintain product licensing this way. An application note, AN232R-02, available from FTDI website (www.ftdichip.com) describes this feature. High Output Drive Option. The parallel FIFO interface and the four FIFO handshake pins can be made to drive out at three times the standard signal drive level thus allowing multiple devices to be driven, or devices that require a greater signal drive strength to be interfaced to the FT245R. This option is configured in the internal EEPROM. Programmable FIFO RX Buffer Timeout. The FIFO RX buffer timeout is used to flush remaining data from the receive buffer. This timeout defaults to 16ms, but is programmable over USB in 1ms increments from 2ms to 255ms, thus allowing the device to be optimised for protocols that require fast response times from short data packets. Wake Up Function. If USB is in suspend mode, and remote wake up has been enabled in the internal EEPROM (it is enabled by default), the RXF# pin becomes an input. Strobing this pin low for a minimum of 20ms will cause the FT245R to request a resume from suspend on the USB bus. Normally this can be used to wake up the host PC from suspend. The FT245R is capable of operating at a voltage supply between +3.3V and +5V with a nominal operational mode current of 15mA and a nominal USB suspend mode current of 70µA. This allows greater margin for peripheral designs to meet the USB suspend mode current limit of 2.5mA. An integrated level converter within the FIFO interface allows the FT245R to interface to FIFO logic running at +1.8V, 2.5V, +3.3V or +5V. Copyright © 2010 Future Technology Devices International Limited 15 Document No.: FT_000052 FT245R USB FIFO IC Datasheet Version 2.13 Clearance No.: FTDI# 39 4.2 Functional Block Descriptions The following paragraphs detail each function within the FT245R. Please refer to the block diagram shown in Figure 2.1. Internal EEPROM. The internal EEPROM in the FT245R is used to store USB Vendor ID (VID), Product ID (PID), device serial number, product description string and various other USB configuration descriptors. The FT245R is supplied with the internal EEPROM pre-programmed as described in Section 8. A user area of the internal EEPROM is available to system designers to allow storing additional data. The internal EEPROM descriptors can be programmed in circuit, over USB without any additional voltage requirement. It can be programmed using the FTDI utility software called MPROG and FT_PROG, which can be downloaded from FTDI Utilities on the FTDI website (www.ftdichip.com). +3.3V LDO Regulator. The +3.3V LDO regulator generates the +3.3V reference voltage for driving the USB transceiver cell output buffers. It requires an external decoupling capacitor to be attached to the 3V3OUT regulator output pin. It also provides +3.3V power to the 1.5kΩ internal pull up resistor on USBDP. The main function of the LDO is to power the USB Transceiver and the Reset Generator Cells rather than to power external logic. However, it can be used to supply external circuitry requiring a +3.3V nominal supply with a maximum current of 50mA. USB Transceiver. The USB Transceiver Cell provides the USB 1.1 / USB 2.0 full-speed physical interface to the USB cable. The output drivers provide +3.3V level slew rate control signalling, whilst a differential input receiver and two single ended input receivers provide USB data in, Single-Ended-0 (SE0) and USB reset detection conditions respectfully. This function also incorporates the internal USB series termination resistors on the USB data lines and a 1.5kΩ pull up resistor on USBDP. USB DPLL. The USB DPLL cell locks on to the incoming NRZI USB data and generates recovered clock and data signals for the Serial Interface Engine (SIE) block. Internal 12MHz Oscillator. The Internal 12MHz Oscillator cell generates a 12MHz reference clock. This provides an input to the x4 Clock Multiplier function. The 12MHz Oscillator is also used as the reference clock for the SIE, USB Protocol Engine and FIFO controller blocks. Clock Multiplier / Divider. The Clock Multiplier / Divider takes the 12MHz input from the Internal Oscillator function and generates the 48MHz. The 48Mz clock reference is used by the USB DPLL and the Baud Rate Generator blocks. Serial Interface Engine (SIE). The Serial Interface Engine (SIE) block performs the parallel to serial and serial to parallel conversion of the USB data. In accordance with the USB 2.0 specification, it performs bit stuffing/un-stuffing and CRC5/CRC16 generation. It also checks the CRC on the USB data stream. USB Protocol Engine. The USB Protocol Engine manages the data stream from the device USB control endpoint. It handles the low level USB protocol requests generated by the USB host controller and the commands for controlling the functional parameters of the FIFO in accordance with the USB 2.0 specification Section 9. FIFO RX Buffer (128 bytes). Data sent from the USB host controller to the FIFO via the USB data OUT endpoint is stored in the FIFO RX (receive) buffer and is removed from the buffer by reading the contents of the FIFO using the RD# pin. (Rx relative to the USB interface). FIFO TX Buffer (256 bytes). Data written into the FIFO using the WR pin is stored in the FIFO TX (transmit) Buffer. The USB host controller removes data from the FIFO TX Buffer by sending a USB request for data from the device data IN endpoint. (Tx relative to the USB interface). FIFO Controller with Programmable High Drive. The FIFO Controller handles the transfer of data between the FIFO RX, the FIFO TX buffers and the external FIFO interface pins (D0 - D7). Additionally, the FIFO signals have a configurable high drive strength capability which is configurable in the EEPROM. RESET Generator. The integrated Reset Generator Cell provides a reliable power-on reset to the device internal circuitry at power up. The RESET# input pin allows an external device to reset the FT245R. RESET# can be tied to VCC or left unconnected if not being used. Copyright © 2010 Future Technology Devices International Limited 16 Document No.: FT_000052 FT245R USB FIFO IC Datasheet Version 2.13 Clearance No.: FTDI# 39 5 Devices Characteristics and Ratings 5.1 Absolute Maximum Ratings The absolute maximum ratings for the FT232R devices are as follows. These are in accordance with the Absolute Maximum Rating System (IEC 60134). Exceeding these may cause permanent damage to the device. Parameter Value Units Storage Temperature -65 to 150 °C Floor Life (Out of Bag) At Factory Ambient 168 (30°C / 60% Relative Humidity) (IPC/JEDEC J-STD-033A MSL Level 3 Compliant)* Hours Ambient Temperature (Power Applied) -40 to 85 °C MTTF FT245RL 6607685 hours MTTF FT245RQ 4464815 hours VCC Supply Voltage -0.5 to +6.00 V DC Input Voltage – USBDP and USBDM -0.5 to +3.8 V DC Input Voltage – High Impedance Bidirectionals -0.5 to + (VCC +0.5) V DC Input Voltage – All Other Inputs -0.5 to + (VCC +0.5) V DC Output Current – Outputs 24 mA Power Dissipation (VCC = 5.25V) 500 mW Table 5.1 Absolute Maximum Ratings * If devices are stored out of the packaging beyond this time limit the devices should be baked before use. The devices should be ramped up to a temperature of +125°C and baked for up to 17 hours. Copyright © 2010 Future Technology Devices International Limited 17 Document No.: FT_000052 FT245R USB FIFO IC Datasheet Version 2.13 Clearance No.: FTDI# 39 5.2 DC Characteristics DC Characteristics (Ambient Temperature = -40°C to +85°C) Parameter Description Minimum Typical Maximum Units Conditions VCC1 VCC Operating Supply Voltage 4.0 --- 5.25 V Using Internal Oscillator VCC1 VCC Operating Supply Voltage 3.3 --- 5.25 V Using External Crystal VCC2 VCCIO Operating Supply Voltage 1.8 --- 5.25 V Icc1 Operating Supply Current --- 15 --- mA Normal Operation Icc2 Operating Supply Current 50 70 100 μA USB Suspend 3V3 3.3v regulator output 3.0 3.3 3.6 V Table 5.2 Operating Voltage and Current Parameter Description Minimum Typical Maximum Units Conditions Voh Output Voltage High 3.2 4.1 4.9 V I source = 2mA Vol Output Voltage Low 0.3 0.4 0.6 V I sink = 2mA Vin Input Switching Threshold 1.0 1.2 1.5 V ** VHys Input Switching Hysteresis 20 25 30 mV ** Table 5.3 UART and CBUS I/O Pin Characteristics (VCCIO = +5.0V, Standard Drive Level) Parameter Description Minimum Typical Maximum Units Conditions Voh Output Voltage High 2.2 2.7 3.2 V I source = 1mA Vol Output Voltage Low 0.3 0.4 0.5 V I sink = 2mA Vin Input Switching Threshold 1.0 1.2 1.5 V ** VHys Input Switching Hysteresis 20 25 30 mV ** Table 5.4 UART and CBUS I/O Pin Characteristics (VCCIO = +3.3V, Standard Drive Level) Copyright © 2010 Future Technology Devices International Limited 18 Document No.: FT_000052 FT245R USB FIFO IC Datasheet Version 2.13 Clearance No.: FTDI# 39 Parameter Description Minimum Typical Maximum Units Conditions Voh Output Voltage High 2.1 2.6 2.8 V I source = 1mA Vol Output Voltage Low 0.3 0.4 0.5 V I sink = 2mA Vin Input Switching Threshold 1.0 1.2 1.5 V ** VHys Input Switching Hysteresis 20 25 30 mV ** Table 5.5 UART and CBUS I/O Pin Characteristics (VCCIO = +2.8V, Standard Drive Level) Parameter Description Minimum Typical Maximum Units Conditions Voh Output Voltage High 1.32 1.62 1.8 V I source = 0.2mA Vol Output Voltage Low 0.06 0.1 0.18 V I sink = 0.5mA Vin Input Switching Threshold 1.0 1.2 1.5 V ** VHys Input Switching Hysteresis 20 25 30 mV ** Table 5.6 UART and CBUS I/O Pin Characteristics (VCCIO = +1.8V, Standard Drive Level) Parameter Description Minimum Typical Maximum Units Conditions Voh Output Voltage High 3.2 4.1 4.9 V I source = 6mA Vol Output Voltage Low 0.3 0.4 0.6 V I sink = 6mA Vin Input Switching Threshold 1.0 1.2 1.5 V ** VHys Input Switching Hysteresis 20 25 30 mV ** Table 5.7 UART and CBUS I/O Pin Characteristics (VCCIO = +5.0V, High Drive Level) Parameter Description Minimum Typical Maximum Units Conditions Voh Output Voltage High 2.2 2.8 3.2 V I source = 3mA Vol Output Voltage Low 0.3 0.4 0.6 V I sink = 8mA Vin Input Switching Threshold 1.0 1.2 1.5 V ** VHys Input Switching Hysteresis 20 25 30 mV ** Table 5.8 UART and CBUS I/O Pin Characteristics (VCCIO = +3.3V, High Drive Level) Copyright © 2010 Future Technology Devices International Limited 19 Document No.: FT_000052 FT245R USB FIFO IC Datasheet Version 2.13 Clearance No.: FTDI# 39 Parameter Description Minimum Typical Maximum Units Conditions Voh Output Voltage High 2.1 2.6 2.8 V I source = 3mA Vol Output Voltage Low 0.3 0.4 0.6 V I sink = 8mA Vin Input Switching Threshold 1.0 1.2 1.5 V ** VHys Input Switching Hysteresis 20 25 30 mV ** Table 5.9 UART and CBUS I/O Pin Characteristics (VCCIO = +2.8V, High Drive Level) Parameter Description Minimum Typical Maximum Units Conditions Voh Output Voltage High 1.35 1.67 1.8 V I source = 0.4mA Vol Output Voltage Low 0.12 0.18 0.35 V I sink = 3mA Vin Input Switching Threshold 1.0 1.2 1.5 V ** VHys Input Switching Hysteresis 20 25 30 mV ** Table 5.10 UART and CBUS I/O Pin Characteristics (VCCIO = +1.8V, High Drive Level) ** Only input pins have an internal 200KΩ pull-up resistor to VCCIO Parameter Description Minimum Typical Maximum Units Vin Input Switching Threshold 1.3 1.6 1.9 V VHys Input Switching Hysteresis 50 55 60 mV Conditions Table 5.11 RESET# and TEST Pin Characteristics Copyright © 2010 Future Technology Devices International Limited 20 Document No.: FT_000052 FT245R USB FIFO IC Datasheet Version 2.13 Clearance No.: FTDI# 39 Parameter Description Minimum UVoh I/O Pins Static Output (High) UVol Typical Maximum Units Conditions 2.8 3.6 V RI = 1.5kΩ to 3V3OUT (D+) RI = 15KΩ to GND (D-) I/O Pins Static Output (Low) 0 0.3 V RI = 1.5kΩ to 3V3OUT (D+) RI = 15kΩ to GND (D-) UVse Single Ended Rx Threshold 0.8 2.0 V UCom Differential Common Mode 0.8 2.5 V UVDif Differential Input Sensitivity 0.2 UDrvZ Driver Output Impedance 26 V 29 44 Ohms See Note 1 Table 5.12 USB I/O Pin (USBDP, USBDM) Characteristics 5.3 EEPROM Reliability Characteristics The internal 1024 Bit EEPROM has the following reliability characteristics: Parameter Value Units Data Retention 10 Years Write 10,000 Cycles Read Unlimited Cycles Table 5.13 EEPROM Characteristics 5.4 Internal Clock Characteristics The internal Clock Oscillator has the following characteristics: Value Parameter Unit Minimum Typical Maximum Frequency of Operation (see Note 1) 11.98 12.00 12.02 MHz Clock Period 83.19 83.33 83.47 ns Duty Cycle 45 50 55 % Table 5.14 Internal Clock Characteristics Note 1: Equivalent to +/-1667ppm Copyright © 2010 Future Technology Devices International Limited 21 Document No.: FT_000052 FT245R USB FIFO IC Datasheet Version 2.13 Clearance No.: FTDI# 39 Parameter Description Minimum Typical Maximum Units Conditions Voh Output Voltage High 2.1 2.8 3.2 V I source = 3mA Vol Output Voltage Low 0.3 0.4 0.6 V I sink = 8mA Vin Input Switching Threshold 1.0 1.2 1.5 V Table 5.15 OSCI, OSCO Pin Characteristics – see Note 1 Note1: When supplied, the FT232R is configured to use its internal clock oscillator. These characteristics only apply when an external oscillator or crystal is used. 5.5 Thermal Characteristics The FT245RL package has the following thermal characteristics: Parameter Value Units Conditions Theta JA (ƟJA) 55.82 °C/W Still air Theta JC (ƟJC) 24.04 °C/W Table 5.16 FT245RL Thermal Characteristics The FT245RQ package has the following thermal characteristics: Parameter Value Units Conditions Theta JA (ƟJA) 31.49 °C/W Still air, center pad soldered to PCB, 9 vias to another plane Theta JA (ƟJA) 62.31 °C/W Still air, center pad unsoldered Theta JC (ƟJC) °C/W Table 5.17 FT245RQ Thermal Characteristics Copyright © 2010 Future Technology Devices International Limited 22 Document No.: FT_000052 FT245R USB FIFO IC Datasheet Version 2.13 Clearance No.: FTDI# 39 6 USB Power Configurations The following sections illustrate possible USB power configurations for the FT245R. The illustrations have omitted pin numbers for ease of understanding since the pins differ between the FT245RL and FT245RQ package options. All USB power configurations illustrated apply to both package options for the FT245R device. Please refer to Section 3 for the package option pin-out and signal descriptions. 6.1 USB Bus Powered Configuration Ferrite Bead Vcc 1 D0 VCC D1 2 USBDM D2 3 USBDP D3 4 VCCIO D4 10nF FT245R NC 5 D5 RESET# D6 NC SHIELD D7 OSCI GND TXE# Vcc OSCO RXF# VCC 100nF 4.7uF RD# 3V3OUT + 100nF A G N D G N D G N D G N D 10K T WR E S PWREN# T GND GND GND Figure 6.1 Bus Powered Configuration Figure 6.1 illustrates the FT245R in a typical USB bus powered design configuration. A USB bus powered device gets its power from the USB bus. Basic rules for USB bus power devices are as follows – i) ii) iii) iv) v) On plug-in to USB, the device should draw no more current than 100mA. In USB Suspend mode the device should draw no more than 2.5mA. A bus powered high power USB device (one that draws more than 100mA) should use the PWREN# to keep the current below 100mA on plug-in and 2.5mA on USB suspend. A device that consumes more than 100mA cannot be plugged into a USB bus powered hub. No device can draw more than 500mA from the USB bus. The power descriptors in the internal EEPROM of the FT245R should be programmed to match the current drawn by the device. A ferrite bead is connected in series with the USB power supply to reduce EMI noise from the FT245R and associated circuitry being radiated down the USB cable to the USB host. The value of the Ferrite Bead depends on the total current drawn by the application. A suitable range of Ferrite Beads is available from Steward (www.steward.com), for example Steward Part # MI0805K400R-10. Note: If using PWREN#, the pin should be pulled to VCCIO using a 10kΩ resistor. Copyright © 2010 Future Technology Devices International Limited 23 Document No.: FT_000052 FT245R USB FIFO IC Datasheet Version 2.13 Clearance No.: FTDI# 39 6.2 Self Powered Configuration Figure 6.2 Self Powered Configuration Figure 6.2 illustrates the FT245R in a typical USB self powered configuration. A USB self powered device gets its power from its own power supply, VCC, and does not draw current from the USB bus. The basic rules for USB self powered devices are as follows – i) ii) iii) A self powered device should not force current down the USB bus when the USB host or hub controller is powered down. A self powered device can use as much current as it needs during normal operation and USB suspend as it has its own power supply. A self powered device can be used with any USB host, a bus powered USB hub or a self powered USB hub. The power descriptor in the internal EEPROM of the FT245R should be programmed to a value of zero (self powered). In order to comply with the first requirement above, the USB bus power (pin 1) is used to control the RESET# pin of the FT245R device. When the USB host or hub is powered up an internal 1.5kΩ resistor on USBDP is pulled up to +3.3V (generated using the 4K7 and 10k resistor network), thus identifying the device as a full speed device to the USB host or hub. When the USB host or hub is powered off, RESET# will be low and the FT245R is held in reset. Since RESET# is low, the internal 1.5kΩ resistor is not pulled up to any power supply (hub or host is powered down), so no current flows down USBDP via the 1.5kΩ pull-up resistor. Failure to do this may cause some USB host or hub controllers to power up erratically. Error! Reference source not found. illustrates a self powered design which has a +4V to +5.25V supply. Note: 1. When the FT232R is in reset, the UART interface I/O pins are tri-stated. Input pins have internal 200kΩ pull-up resistors to VCCIO, so they will gently pull high unless driven by some external logic. 2. When using internal FT232R oscillator the VCC supply voltage range must be +4.0V to 5.25V. 3. When using external oscillator the VCC supply voltage range must be +3.3V to 5.25V Any design which interfaces to +3.3 V or +1.8V would be having a +3.3V or +1.8V supply to VCCIO. Copyright © 2010 Future Technology Devices International Limited 24 Document No.: FT_000052 FT245R USB FIFO IC Datasheet Version 2.13 Clearance No.: FTDI# 39 6.3 USB Bus Powered with Power Switching Configuration P-Channel Power MOSFET s Switched 5V Power to External Logic d g 0.1uF 0.1uF Soft Start Circuit 1k Ferrite Bead 1 D0 5V VCC VCC D1 2 USBDM 3 USBDP D2 D3 4 VCCIO + FT245R D4 NC 5 10nF D5 RESET# SHIELD NC D6 OSCI D7 OSCO GND TXE# 5V VCC RXF# 100nF 4.7uF + GND 3V3OUT A G N D 100nF G N D G N D G N D T E S T RD# 5V VCC 10K WR# PWREN# GND GND Figure 6.3 Bus Powered with Power Switching Configuration A requirement of USB bus powered applications, is when in USB suspend mode the application draws a total current of less than 2.5mA. This requirement includes external logic. Some external logic has the ability to power itself down into a low current state by monitoring the PWREN# signal. For external logic that cannot power itself down in this way, the FT245R provides a simple but effective method of turning off power during the USB suspend mode. Figure 6.3 shows an example of using a discrete P-Channel MOSFET to control the power to external logic. A suitable device to do this is an International Rectifier (www.irf.com) IRLML6402, or equivalent. It is recommended that a “soft start” circuit consisting of a 1kΩ series resistor and a 0.1μF capacitor is used to limit the current surge when the MOSFET turns on. Without the soft start circuit it is possible that the transient power surge, caused when the MOSFET switches on, will reset the FT245R or the USB host/hub controller. The soft start circuit example shown in Figure 6.3 powers up with a slew rate of approximaely12.5V/ms. Thus supply voltage to external logic transitions from GND to +5V in approximately 400 microseconds. As an alternative to the MOSFET, a dedicated power switch IC with inbuilt “soft-start” can be used. A suitable power switch IC for such an application is the Micrel (www.micrel.com) MIC2025-2BM or equivalent. With power switching controlled designs the following should be noted: i) The external logic to which the power is being switched should have its own reset circuitry to automatically reset the logic when power is re-applied when moving out of suspend mode. ii) Set the Pull-down on Suspend option in the internal FT245R EEPROM. iii) The PWREN# pin should be used to switch the power to the external circuitry. iv) For USB high-power bus powered applications (one that consumes greater than 100mA, and up to 500mA of current from the USB bus), the power consumption of the application must be set in the Max Power field in the internal FT245R EEPROM. A high-power bus powered application uses the descriptor in the internal FT245R EEPROM to inform the system of its power requirements. Copyright © 2010 Future Technology Devices International Limited 25 Document No.: FT_000052 FT245R USB FIFO IC Datasheet Version 2.13 Clearance No.: FTDI# 39 v) PWREN# gets its VCC from VCCIO. For designs using 3V3 logic, ensure VCCIO is not powered down using the external logic. In this case use the +3V3OUT. 6.4 USB Bus Powered with Selectable External Logic Supply 3.3V or 5V Supply to External Logic Vcc 100nF Ferrite Bead 1 D0 VCC D1 2 USBDM 3 USBDP D2 D3 1 4 10nF + 5 VCCIO 2 VCCIO 3 NC NC D6 OSCI GND D7 OSCO Vcc 100nF D4 D5 RESET# Jumper SHIELD FT245R TXE# 4.7uF + VCCIO RXF# 3V3OUT A G N D 100nF G N D G N D G N D T E S T RD# 10k WR# PWREN# GND GND GND Figure 6.4 USB Bus Powered with +3.3V or +5V External Logic Power Supply Figure 6.4 illustrates a USB bus power application with selectable external logic supply. The external logic can be selected between +3.3V and +5V using the jumper switch. This jumper is used to allow the FT245R to be interfaced with a +3.3V or +5V logic devices. The VCCIO pin is either supplied with +5V from the USB bus (jumper pins1 and 2 connected), or from the +3.3V output from the FT245R 3V3OUT pin (jumper pins 2 and 3 connected). The supply to VCCIO is also used to supply external logic. With bus powered applications, the following should be noted: i) ii) To comply with the 2.5mA current supply limit during USB suspend mode, PWREN# or SLEEP# signals should be used to power down external logic in this mode. If this is not possible, use the configuration shown in Section 8. The maximum current sourced from the USB bus during normal operation should not exceed 100mA, otherwise a bus powered design with power switching (Section 6.3) should be used. Another possible configuration could use a discrete low dropout (LDO) regulator which is supplied by the 5V on the USB bus to supply between +1.8V and +2.8V to the VCCIO pin and to the external logic. In this case VCC would be supplied with the +5V from the USB bus and the VCCIO would be supplied from the output of the LDO regulator. This results in the FT245R I/O pins driving out at between +1.8V and +2.8V logic levels. For a USB bus powered application, it is important to consider the following when selecting the regulator: i) ii) The regulator must be capable of sustaining its output voltage with an input voltage of +4.35V. An Low Drop Out (LDO) regulator should be selected. The quiescent current of the regulator must be low enough to meet the total current requirement of <= 2.5mA during USB suspend mode. A suitable series of LDO regulators that meets these requirements is the MicroChip/Telcom (www.microchip.com) TC55 series of devices. These devices can supply up to 250mA current and have a quiescent current of under 1μA. Copyright © 2010 Future Technology Devices International Limited 26 Document No.: FT_000052 FT245R USB FIFO IC Datasheet Version 2.13 Clearance No.: FTDI# 39 7 Application Examples The following sections illustrate possible applications of the FT245R. The illustrations have omitted pin numbers for ease of understanding since the pins differ between the FT245RL and FT245RQ package options. 7.1 USB to MCU FIFO Interface VCC VCC Ferrite Bead 1 2 USBDM 3 USBDP + 4 VCCIO 5 D1 I/O11 D2 I/O12 D3 I/O13 FT245R D4 I/O14 D5 I/O15 D6 I/O16 D7 I/O17 RXF# I/O20 TXE# I/O21 RD# I/O22 WR# I/O23 NC RESET# SHIELD NC GND OSCI Vcc OSCO 4.7uF I/O10 + Microcontroller 10nF 100nF D0 VCC 3V3OUT GND 100nF A G N D G N D G N D G N D T E S T I/O24 PWREN# Vcc GND 10k GND Figure 7.1 USB to MCU FIFO Interface A typical example of using the FT245R as a USB to Microcontroller (MCU) FIFO interface is illustrated in Figure 7.1. This example uses two MCU I/O ports: one port (8 bits) to transfer data and the other port (4 or 5 bits) to monitor the TXE# and RXF# status bits and generate the RD# and WR strobes to the FT245R, when required. Using PWREN# for this function is optional. If the Remote Wakeup option is enabled in the internal EEPROM, during USB suspend mode RXF# becomes an input which can be used to wake up the USB host controller by strobing the pin low. Copyright © 2010 Future Technology Devices International Limited 27 Document No.: FT_000052 FT245R USB FIFO IC Datasheet Version 2.13 Clearance No.: FTDI# 39 7.2 Using the External Oscillator The FT245R defaults to operating using its own internal oscillator. This requires that the device is powered with VCC (min)=+4.0V. This supply voltage can be taken from the USB VBUS. Applications which require using an external oscillator, VCC= +3.3V must do so in the following order: 1. When device powered for the very first time, it must have VCC > +4.0V. This supply is available from the USB VBUS supply = +5.0V. 2. The EEPROM must then be programmed to enable external oscillator. This EEPROM modification cannot be done using the FTDI programming utility, MPROG and FT_PROG. The EEPROM can only be re-configured from a custom application. Please refer to the following applications note on how to do this: http://www.ftdichip.com/Documents/AppNotes/AN_100_Using_The_FT232_245R_With_External_ Osc(FT_000067).pdf 3. The FT245R can then be powered from VCC=+3.3V and an external oscillator. This can be done using a link to switch the VCC supply. The FT245R will fail to operate when the internal oscillator has been disabled, but no external oscillator has been connected. Copyright © 2010 Future Technology Devices International Limited 28 Document No.: FT_000052 FT245R USB FIFO IC Datasheet Version 2.13 Clearance No.: FTDI# 39 8 Internal EEPROM Configuration Following a power-on reset or a USB reset the FT245R will scan its internal EEPROM and read the USB configuration descriptors stored there. The default factory programmed values of the internal EEPROM are shown in Table 8.1 Default Internal EEPROM Configuration. Parameter Value Notes USB Vendor ID (VID) 0403h FTDI default VID (hex) USB Product UD (PID) 6001h FTDI default PID (hex) Serial Number Enabled? Yes Serial Number See Note A unique serial number is generated and programmed into the EEPROM during device final test. Pull down I/O Pins in USB Suspend Disabled Enabling this option will make the device pull down on the FIFO interface lines when in USB suspend mode (PWREN# is high). Manufacturer Name FTDI Product Description FT245R USB FIFO Max Bus Power Current 90mA Power Source Bus Powered Device Type FT245R Returns USB 2.0 device description to the host. Note: The device is a USB 2.0 Full Speed device (12Mb/s) as opposed to a USB 2.0 High Speed device (480Mb/s). USB Version 0200 Remote Wake Up Enabled Taking RXF# low will wake up the USB host controller from suspend in approximately 20 ms. High Current I/Os Disabled Enables the high drive level on the FIFO data bus and control I/O pins. Load VCP Driver Enabled Makes the device load the VCP driver interface for the device. Table 8.1 Default Internal EEPROM Configuration The internal EEPROM in the FT245R can be programmed over USB using the FTDI utility program MPROG and FT_PROG which can be downloaded from FTDI Utilities, on the FTDI website (www.ftdichip.com). Version 2.8a or later is required for the FT245R chip. Users who do not have their own USB Vendor ID but who would like to use a unique Product ID in their design can apply to FTDI for a free block of unique PIDs. Contact FTDI support for this service. Copyright © 2010 Future Technology Devices International Limited 29 Document No.: FT_000052 FT245R USB FIFO IC Datasheet Version 2.13 Clearance No.: FTDI# 39 9 Package Parameters The FT245R is available in two different packages. The FT245RL is the SSOP-28 option and the FT245RQ is the QFN-32 package option. The solder reflow profile for both packages is described in Section 0. 9.1 SSOP-28 Package Dimensions 7.80 +/-0.40 5.30 +/-0.30 2.00 Max 1.25 +/-0.12 12° Typ 10.20 +/-0.30 14 0.05 Min FTDI FT245RL 0.65 +/-0.026 YYXX-A XXXXXXXXXXXX 1.02 Typ. 0.30 +/-0.012 1.75 +/- 0.10 28 1 0.09 0° - 8° 0.75 +/-0.20 15 Figure 9.1 SSOP-28 Package Dimensions The FT245RL is supplied in a RoHS compliant 28 pin SSOP package. The package is lead (Pb) free and uses a ‘green’ compound. The package is fully compliant with European Union directive 2002/95/EC. This package is nominally 5.30mm x 10.20mm body (7.80mm x 10.20mm including pins). The pins are on a 0.65 mm pitch. The above mechanical drawing shows the SSOP-28 package. All dimensions are in millimetres. The date code format is YYXX where XX = 2 digit week number, YY = 2 digit year number. The code XXXXXXXXXXXX is the manufacturing LOT code. This only applies to devices manufactured after April 2009. Copyright © 2010 Future Technology Devices International Limited 30 Document No.: FT_000052 FT245R USB FIFO IC Datasheet Version 2.13 Clearance No.: FTDI# 39 9.2 QFN-32 Package Dimensions 32 25 1 24 8 5.000 +/-0.075 FTDI Indicates Pin #1 ( Laser Marked) YYXX-A XXXXXXX FT245RQ 9 17 16 5. 000 +/-0. 075 9 0. 500 0.250 +/-0.050 10 11 12 13 14 15 16 0. 150 Max 8 17 7 18 6 19 5 20 4 21 3 22 2 23 1 24 Pin# 1 ID 32 31 30 29 28 27 26 3.200 +/-0.100 Central Heat Sink Area 0. 200 Min 25 0.500 +/-0.050 3. 200 +/-0. 100 0. 900 +/-0.100 0. 200 0.050 Note: The pin #1 ID is connected internally to the device’s central heat sink area . It is recommended to ground the central heat sink area of the device. Dimensions in mm. Figure 9.2 QFN-32 Package Dimensions The FT245RQ is supplied in a RoHS compliant leadless QFN-32 package. The package is lead ( Pb ) free, and uses a ‘green’ compound. The package is fully compliant with European Union directive 2002/95/EC. This package is nominally 5.00mm x 5.00mm. The solder pads are on a 0.50mm pitch. The above mechanical drawing shows the QFN-32 package. All dimensions are in millimetres. The centre pad on the base of the FT245RQ is not internally connected, and can be left unconnected, or connected to ground (recommended). The date code format is YYXX where XX = 2 digit week number, YY = 2 digit year number. The code XXXXXXX is the manufacturing LOT code. This only applies to devices manufactured after April 2009. Copyright © 2010 Future Technology Devices International Limited 31 Document No.: FT_000052 FT245R USB FIFO IC Datasheet Version 2.13 Clearance No.: FTDI# 39 9.3 QFN-32 Package Typical Pad Layout 2.50 25 0.150 Max 1 0.500 3.200 +/-0.100 0.30 Optional GND Connection 3.200 +/-0.100 Optional GND Connection 0.20 2.50 17 0.200 Min 0.100 9 0.500 +/-0.050 Figure 9.3 Typical Pad Layout for QFN-32 Package 9.4 QFN-32 Package Typical Solder Paste Diagram 2.5 +/- 0.0375 2.5 +/- 0.0375 Figure 9.4 Typical Solder Paste Diagram for QFN-32 Package Copyright © 2010 Future Technology Devices International Limited 32 Document No.: FT_000052 FT245R USB FIFO IC Datasheet Version 2.13 Clearance No.: FTDI# 39 9.5 Solder Reflow Profile The FT245R is supplied in Pb free 28 LD SSOP and QFN-32 packages. The recommended solder reflow profile for both package options is shown in 0. Temperature, T (Degrees C) tp Tp Critical Zone: when T is in the range TL to Tp Ramp Up TL tL TS Max Ramp Down TS Min tS Preheat 25 T = 25º C to TP Time, t (seconds) Figure 9.5 FT245R Solder Reflow Profile The recommended values for the solder reflow profile are detailed in Table 9.1. Values are shown for both a completely Pb free solder process (i.e. the FT245R is used with Pb free solder), and for a non-Pb free solder process (i.e. the FT245R is used with non-Pb free solder). Profile Feature Pb Free Solder Process Non-Pb Free Solder Process 3°C / second Max. 3°C / Second Max. Preheat - Temperature Min (Ts Min.) - Temperature Max (Ts Max.) - Time (ts Min to ts Max) 150°C 200°C 60 to 120 seconds 100°C 150°C 60 to 120 seconds Time Maintained Above Critical Temperature TL: - Temperature (TL) - Time (tL) 217°C 60 to 150 seconds 183°C 60 to 150 seconds 260°C 240°C 20 to 40 seconds 20 to 40 seconds 6°C / second Max. 6°C / second Max. 8 minutes Max. 6 minutes Max. Average Ramp Up Rate (Ts to Tp) Peak Temperature (Tp) Time within 5°C of actual Peak Temperature (tp) Ramp Down Rate Time for T= 25°C to Peak Temperature, Tp Table 9.1 Reflow Profile Parameter Values Copyright © 2010 Future Technology Devices International Limited 33 Document No.: FT_000052 FT245R USB FIFO IC Datasheet Version 2.13 Clearance No.: FTDI# 39 10 Alternative Parts The following list of parts are not all direct drop in replacements but offer similar features as an alternative to the FT245R. The FT-X series is the latest device family offering reduced power and pin count with additional features such as battery charge detection, while the Hi-Speed solution offers faster interfacing. FT245R FT240X FT232H Description Single channel USB to asynchronous FIFO Single channel USB to asynchronous FIFO Single channel USB to asynchronous FIFO (Need MTP to configure) USB Speed USB 2.0 full speed USB 2.0 full speed USB 2.0 hispeed UART Data Rates 1 Mbyte/s 1Mbyte/s 8 Mbyte/s MTP for storing descriptors Internal Internal External 32 pin QFN 24 pin QFN 48 pin QFN 28 pin SSOP 24 pin SSOP 48 pin LQFP FT245R FT234XD FT232H Package options Datasheet Table 10.1 FT245R alternative solutions Copyright © 2010 Future Technology Devices International Limited 34 Document No.: FT_000052 FT245R USB FIFO IC Datasheet Version 2.13 Clearance No.: FTDI# 39 11 Contact Information Head Office – Glasgow, UK Branch Office – Tigard, Oregon, USA Future Technology Devices International Limited Unit 1, 2 Seaward Place Centurion Business Park Glasgow, G41 1HH United Kingdom Tel: +44 (0) 141 429 2777 Fax: +44 (0) 141 429 2758 Future Technology Devices International Limited (USA) 7130 SW Fir Loop Tigard, OR 97223-8160 USA Tel: +1 (503) 547 0988 Fax: +1 (503) 547 0987 E-mail (Sales) [email protected] E-mail (Support) [email protected] E-mail (General Enquiries) [email protected] Web Site URL http://www.ftdichip.com Web Shop URL http://www.ftdichip.com E-Mail (Sales) E-Mail (Support) E-Mail (General Enquiries) [email protected] [email protected] [email protected] Branch Office – Shanghai, China Branch Office – Taipei, Taiwan Future Technology Devices International Limited (Taiwan) 2F, No 516, Sec. 1 NeiHu Road Taipei 114 Taiwan, R.O.C. Tel: +886 (0) 2 8791 3570 Fax: +886 (0) 2 8791 3576 E-mail (Sales) [email protected] E-mail (Support) [email protected] E-mail (General Enquiries) [email protected] Web Site URL http://www.ftdichip.com Future Technology Devices International Limited (China) Room 1103, No. 666 West Huaihai Road, Shanghai, 200052 China Tel: +86 21 62351596 Fax: +86 21 62351595 E-Mail (Sales): [email protected] E-Mail (Support): [email protected] E-Mail (General Enquiries): [email protected] Web Site URL: http://www.ftdichip.com Distributor and Sales Representatives Please visit the Sales Network page of the FTDI Web site for the contact details of our distributor(s) and sales representative(s) in your country. System and equipment manufacturers and designers are responsible to ensure that their systems, and any Future Technology Devices International Ltd (FTDI) devices incorporated in their systems, meet all applicable safety, regulatory and system-level performance requirements. All application-related information in this document (including application descriptions, suggested FTDI devices and other materials) is provided for reference only. While FTDI has taken care to assure it is accurate, this information is subject to customer confirmation, and FTDI disclaims all liability for system designs and for any applications assistance provided by FTDI. Use of FTDI devices in life support and/or safety applications is entirely at the user’s risk, and the user agrees to defend, indemnify and hold harmless FTDI from any and all damages, claims, suits or expense resulting from such use. This document is subject to change without notice. No freedom to use patents or other intellectual property rights is implied by the publication of this document. Neither the whole nor any part of the information contained in, or the product described in this document, may be adapted or reproduced in any material or electronic form without the prior written consent of the copyright holder. Future Technology Devices International Ltd, Unit 1, 2 Seaward Place, Centurion Business Park, Glasgow G41 1HH, United Kingdom. Scotland Registered Company Number: SC136640 . Copyright © 2010 Future Technology Devices International Limited 35 Document No.: FT_000052 FT245R USB FIFO IC Datasheet Version 2.13 Clearance No.: FTDI# 39 Appendix A - References Useful Application Notes http://www.ftdichip.com/Documents/AppNotes/AN232R-01_FT232RBitBangModes.pdf http://www.ftdichip.com/Documents/AppNotes/AN_107_AdvancedDriverOptions_AN_000073.pdf http://www.ftdichip.com/Documents/AppNotes/AN232R-02_FT232RChipID.pdf http://www.ftdichip.com/Documents/AppNotes/AN_121_FTDI_Device_EEPROM_User_Area_Usage.pdf http://www.ftdichip.com/Documents/AppNotes/AN_120_Aliasing_VCP_Baud_Rates.pdf http://www.ftdichip.com/Documents/AppNotes/AN_100_Using_The_FT232_245R_With_External_Osc(FT_ 000067).pdf http://www.ftdichip.com/Resources/Utilities/AN_126_User_Guide_For_FT232_Factory%20test%20utility. pdf http://www.ftdichip.com/Documents/AppNotes/AN232B-05_BaudRates.pdf http://www.ftdichip.com/Documents/InstallGuides.htm Copyright © 2010 Future Technology Devices International Limited 36 Document No.: FT_000052 FT245R USB FIFO IC Datasheet Version 2.13 Clearance No.: FTDI# 39 Appendix B - List of Figures and Tables List of Figures Figure 2.1 FT245R Block Diagram ................................................................................................... 4 Figure 3.1 SSOP Package Pin Out and Schematic Symbol ................................................................... 7 Figure 3.2 QFN-32 Package Pin Out and schematic symbol .............................................................. 10 Figure 3.3 FIFO Read Cycle .......................................................................................................... 13 Figure 3.4 FIFO Write Cycle ......................................................................................................... 14 Figure 7.1 Bus Powered Configuration ........................................................................................... 23 Figure 7.2 Self Powered Configuration ........................................................................................... 24 Figure 7.3 Bus Powered with Power Switching Configuration ............................................................ 25 Figure 7.4 USB Bus Powered with +3.3V or +5V External Logic Power Supply .................................... 26 Figure 8.1 USB to MCU FIFO Interface ........................................................................................... 27 Figure 10.1 SSOP-28 Package Dimensions ..................................................................................... 30 Figure 10.2 QFN-32 Package Dimensions ....................................................................................... 31 Figure 10.3 Typical Pad Layout for QFN-32 Package ........................................................................ 32 Figure 10.4 Typical Solder Paste Diagram for QFN-32 Package ......................................................... 32 Figure 10.5 FT245R Solder Reflow Profile ....................................................................................... 33 List of Tables Table 3.1 USB Interface Group ....................................................................................................... 7 Table 3.2 Power and Ground Group ................................................................................................. 8 Table 3.3 Miscellaneous Signal Group .............................................................................................. 8 Table 3.4 FIFO Interface Group (see note 3) .................................................................................... 9 Table 3.5 USB Interface Group ..................................................................................................... 10 Table 3.6 Power and Ground Group ............................................................................................... 11 Table 3.7 Miscellaneous Signal Group ............................................................................................ 11 Table 3.8 FIFO Interface Group (see note 3) .................................................................................. 12 Table 3.9 FIFO Read Cycle Timings ............................................................................................... 13 Table 3.10 FIFO Write Cycle ......................................................................................................... 14 Table 5.1 Absolute Maximum Ratings ............................................................................................ 17 Table 5.2 Operating Voltage and Current ....................................................................................... 18 Table 5.3 UART and CBUS I/O Pin Characteristics (VCCIO = +5.0V, Standard Drive Level) .................. 18 Table 5.4 UART and CBUS I/O Pin Characteristics (VCCIO = +3.3V, Standard Drive Level) .................. 18 Table 5.5 UART and CBUS I/O Pin Characteristics (VCCIO = +2.8V, Standard Drive Level) .................. 19 Table 5.6 UART and CBUS I/O Pin Characteristics (VCCIO = +1.8V, Standard Drive Level) .................. 19 Table 5.7 UART and CBUS I/O Pin Characteristics (VCCIO = +5.0V, High Drive Level) ......................... 19 Table 5.8 UART and CBUS I/O Pin Characteristics (VCCIO = +3.3V, High Drive Level) ......................... 19 Table 5.9 UART and CBUS I/O Pin Characteristics (VCCIO = +2.8V, High Drive Level) ......................... 20 Table 5.10 UART and CBUS I/O Pin Characteristics (VCCIO = +1.8V, High Drive Level) ....................... 20 Table 5.11 RESET# and TEST Pin Characteristics ............................................................................ 20 Table 5.12 USB I/O Pin (USBDP, USBDM) Characteristics ................................................................. 21 Table 5.13 EEPROM Characteristics ............................................................................................... 21 Copyright © 2010 Future Technology Devices International Limited 37 Document No.: FT_000052 FT245R USB FIFO IC Datasheet Version 2.13 Clearance No.: FTDI# 39 Table 5.14 Internal Clock Characteristics ....................................................................................... 21 Table 5.15 OSCI, OSCO Pin Characteristics – see Note 1 ................................................................. 22 Table 5.16 FT245RL Thermal Characteristics .................................................................................. 22 Table 5.17 FT245RQ Thermal Characteristics.................................................................................. 22 Table 8.1 Default Internal EEPROM Configuration............................................................................ 29 Table 9.1 Reflow Profile Parameter Values ..................................................................................... 33 Table 10.1 FT245R alternative solutions ........................................................................................ 34 Copyright © 2010 Future Technology Devices International Limited 38 Document No.: FT_000052 FT245R USB FIFO IC Datasheet Version 2.13 Clearance No.: FTDI# 39 Appendix C - Revision History Document Title: USB UART IC FT245R Document Reference No.: FT_000052 Clearance No.: FTDI# 39 Product Page: http://www.ftdichip.com/FTProducts.htm Document Feedback: Send Feedback Version 0.90 Initial Datasheet Created August 2005 Version 0.94 Revised Pre-release datasheet October 2005 Version 1.00 Full datasheet released December 2005 Version 1.02 Minor revisions to datasheet released December 2005 Version 1.03 Manufacturer ID added to default EEPROM data January 2006 Version 1.04 Buffer sizes added January 2006 Version 1.05 QFN-32 Package pad layout and solder paste diagrams added January 2006 Version 2.00 Reformatted, added notes for 3.3V operation; June 2008 Part numbers, TID, corrected; QFN Package drawing corrected. Added FIFO characteristics for +1.8V; Added MTTF data Corrected the input switching threshold and input hysteresis figures for VCCIO=+5V Version 2.01 Corrected the RX and TX Buffer data flow direction in the block Diagram Figure 2.1 Version 2.02 July 2008 Removed repeated section of table 8.1 Improved graphics on Figures 6.2, 6.3, 6.4 and 7.1 Add Packing details Changed USB suspend current spec from 500uA to 2.5m Corrected Figure 9.2 QFN dimensions. Version 2.03 Amended definition of FIFO TX and RX buffers to be consistent Updated company contact information. Version 2.04 August 2008 February 2009 Corrected Tape and Reel quantities Added LOT numbers to the device markings. Clarified VCC operation and added section headed “Using an external Oscillator” Added 3V3 regulator output tolerance April 2009 Version 2.05 Corrected Tx and RX buffer sizes on front page June 2009 Version 2.06 Additional dimensions added to QFN solder profile Version 2.07 Changed label ‘D6’ to 'D7' (pin 3) on FT245RQ schematic symbol June 2009 Updated to latest TID number Version 2.08 Added Window 7 support October 2009 Modified package dimensions to 5.0 x 5.0 +/-0.075mm. December 2009 and Solder paste diagram to 2.50 x 2.50 +/-0.0375mm Added FT_PROG utility references Added Appendix A-references Corrected USB-IF TID Version 2.09 Updated section 6.2, Figure 6.2 and the note, May 2010 Updated section 5.3, Table 5.13, EEPROM data retention time Version 2.10 Removed RD# and WR# references on BitBang modes July 2010 Corrected US Support email address. Added USB Compliance logo Copyright © 2010 Future Technology Devices International Limited 39 Document No.: FT_000052 FT245R USB FIFO IC Datasheet Version 2.13 Clearance No.: FTDI# 39 Version 2.11 Updated USB-IF TID for Rev C April 2011 Version 2.12 Corrected TID for Rev C April 2011 Version 2.13 Added Thermal Characteristics (Section 5.5) February 2015 Added document information and feedback to revision history Added section 10 on alternative parts Copyright © 2010 Future Technology Devices International Limited 40