Future Technology Devices International Ltd. FT200XD

FT200XD USB I2C SLAVE IC Datasheet
Version 1.3
Document No.: FT_000628 Clearance No.: FTDI# 265
Future Technology Devices
International Ltd.
FT200XD
(USB I2C SLAVE IC)
The FT200XD is a USB to I2C interface
with the following advanced features:

USB Power Configurations; supports buspowered, self-powered and bus-powered with
power switching.

Single chip USB to I2C interface.

Integrated +3.3V level converter for USB I/O.

Up to 3.4MHz, high speed mode, I2C supported


Entire USB protocol handled on the chip. No
USB specific firmware programming required.
True 3.3VCMOS drive output and TTL input;
Operates down to 1V8 with external pull-ups.
Tolerant of 5V input.

Fully
integrated
2048
byte
multi-timeprogrammable (MTP) memory storing device
descriptors and CBUS I/O configuration.

Configurable I/O pin output drive strength; 4
mA(min) and 16 mA(max).

Integrated power-on-reset circuit.

Fully integrated clock generation with no
external crystal required plus optional clock
output selection enabling a glue-less interface
to external MCU or FPGA.

Fully integrated AVCC supply filtering - no
external filtering required.

+ 5V Single Supply Operation.
512 byte receive buffer and 512 byte transmit
buffer utilising buffer smoothing technology to
allow for high data throughput.

Internal 3V3/1V8 LDO regulators

Low operating and USB suspend current; 8mA
(active-typ) and 125uA (suspend-typ).

UHCI/OHCI/EHCI host controller compatible.

USB 2.0 Full Speed compatible.

Extended operating temperature range; -40⁰C
to +85⁰C.

Available in compact Pb-free 10 Pin DFN
package (3mmx3mm) (RoHS compliant).


FTDI’s royalty-free Virtual Com Port (VCP) and
Direct
(D2XX)
drivers
eliminate
the
requirement for USB driver development in
most cases.

Unique USB FTDIChip-ID™ feature.

Configurable CBUS I/O pin.

Transmit and receive LED drive signals.

USB Battery Charger Detection. Allows for USB
peripheral devices to detect the presence of a
higher power source to enable improved
charging.

Device supplied pre-programmed with unique
USB serial number.
Neither the whole nor any part of the information contained in, or the product described in this manual, may be adapted or reproduced
in any material or electronic form without the prior written consent of the copyright holder. This product and its documentation are
supplied on an as-is basis and no warranty as to their suitability for any particular purpose is either made or implied. Future Technology
Devices International Ltd will not accept any claim for damages howsoever arising as a result of use or failure of this product. Your
statutory rights are not affected. This product or any variant of it is not intended for use in any medical appliance, device or system in
which the failure of the product might reasonably be expected to result in personal injury. This document provides preliminar y
information that may be subject to change without notice. No freedom to use patents or other intellectual property rights is implied by
the publication of this document. Future Technology Devices International Ltd, Unit 1, 2 Seaward Place, Centurion Business Park, Glasgow
G41 1HH United Kingdom. Scotland Registered Company Number: SC136640
Copyright © 2013 Future Technology Devices International Limited
1
FT200XD USB I2C SLAVE IC Datasheet
Version 1.3
Document No.: FT_000628 Clearance No.: FTDI# 265
1
Typical Applications

Upgrading Legacy Peripherals to USB

Utilising USB to add system modularity

Incorporate USB interface to enable PC
transfers for development system
communication

Motherboard and system monitoring through
USB

USB dongle implementations for Software/
Hardware Encryption and Wireless Modules

Interfacing MCU/PLD/FPGA based designs to
add USB connectivity

USB Instrumentation

USB Industrial Control

USB Digital Camera Interface

Capable of detecting dedicated USB charger
ports for charging batteries with high current
1.1 Driver Support
Royalty free VIRTUAL COM PORT
(VCP) DRIVERS for...
Royalty free D2XX Direct Drivers
(USB Drivers + DLL S/W Interface)

Windows 8 32-,64-bit

Windows 8 32-,64-bit

Windows 7 32-,64-bit

Windows 7 32-,64-bit

Windows Vista and Vista 64-bit

Windows Vista and Vista 64-bit

Windows XP and XP 64-bit

Windows XP and XP 64-bit

Windows Embedded Operating Systems

Windows Embedded Operating Systems

Server 2003, XP and Server 2008

Server 2003, XP and Server 2008

Windows CE 4.2, 5.0 and 6.0

Windows CE 4.2, 5.0 and 6.0

Mac OS-X

Mac OS-X

Linux 3.2 and greater

Linux 2.6 and greater

Android OS

Android OS
The drivers listed above are all available to download for free from FTDI website (www.ftdichip.com).
Various 3rd party drivers are also available for other operating systems - see FTDI
website(www.ftdichip.com) for details.
For driver installation, please refer tohttp://www.ftdichip.com/Documents/InstallGuides.htm
1.2 Part Numbers
Part Number
Package
FT200XD-x
10 Pin DFN
Table 1.1 Ordering part numbers
Note: Packing codes for -x is:
- R: Taped and Reel, 5,000pcs per reel
- T: Tray packing, 490pcs per tray
For example: FT200XD-R is 5,000pcs taped and reel packing
Copyright © 2013 Future Technology Devices International Limited
2
FT200XD USB I2C SLAVE IC Datasheet
Version 1.3
Document No.: FT_000628 Clearance No.: FTDI# 265
1.3 USB Compliant
The FT200XD is fully compliant with the USB 2.0 specification and has been given the USB-IF Test-ID
(TID) 40001459 (Rev D).
Copyright © 2013 Future Technology Devices International Limited
3
FT200XD USB I2C SLAVE IC Datasheet
Version 1.3
Document No.: FT_000628 Clearance No.: FTDI# 265
2
FT200XD Block Diagram
VCC
1V8 Internal
Core Supply
3V3OUT
3.3 Volt LDO
Regulator
1.8 Volt LDO
Regulator
FIFO RX Buffer
(512 bytes)
VCCIO
SDA
SCL
USBDP
USBDM
USB
Transceiver
with
Integrated
1.5k pullups
and battery
charge
detection
Serial Interface
Engine
(SIE)
USB
Protocol Engine
I2C Controller
CBUS0
Internal MTP
Memory
USB DPLL
FIFO TX Buffer
(512 bytes)
Internal
12MHz
Oscillator
3V3OUT
RESET#
X4 Clock
Multiplier
Reset
Generator
48MHz
To USB Transceiver Cell
GND
Figure 2.1FT200XD Block Diagram
For a description of each function please refer to Section 4.
Copyright © 2013 Future Technology Devices International Limited
4
FT200XD USB I2C SLAVE IC Datasheet
Version 1.3
Document No.: FT_000628 Clearance No.: FTDI# 265
Table of Contents
1
Typical Applications ...................................................................... 2
1.1
Driver Support .................................................................................... 2
1.2
Part Numbers...................................................................................... 2
1.3
USB Compliant .................................................................................... 3
2
FT200XD Block Diagram ............................................................... 4
3
Device Pin Out and Signal Description .......................................... 7
3.1
10-LD DFN Package ............................................................................ 7
3.1.1
3.2
4
DFN Package Pin Out Description ................................................................................... 7
CBUS Signal Options ........................................................................... 9
Function Description................................................................... 10
4.1
Key Features ..................................................................................... 10
4.2
Functional Block Descriptions ........................................................... 10
5
I2C Interface Description ............................................................ 12
6
Devices Characteristics and Ratings ........................................... 13
6.1
Absolute Maximum Ratings............................................................... 13
6.2
ESD and Latch-up Specifications ....................................................... 13
6.3
DC Characteristics............................................................................. 14
6.4
MTP Memory Reliability Characteristics ............................................ 18
6.5
Internal Clock Characteristics ........................................................... 18
7
USB Power Configurations .......................................................... 19
7.1
USB Bus Powered Configuration ...................................................... 19
7.2
Self Powered Configuration .............................................................. 20
7.3
USB Bus Powered with Power Switching Configuration .................... 21
8
Application Examples ................................................................. 22
8.1
USB to I2C Converter......................................................................... 22
8.2
USB Battery Charging Detection ....................................................... 23
USB and I2C Interfacing ............................................................. 25
9
9.1
Host Interface (USB) ........................................................................ 25
9.1.1
VCP and D2xx Interfaces ............................................................................................ 25
9.1.2
Reading and Writing Data ........................................................................................... 26
I2C Interface ..................................................................................... 27
9.2
9.2.1
Addressing ................................................................................................................ 27
9.2.2
Data Transfers .......................................................................................................... 27
9.3
10
Other I2C Commands ........................................................................ 29
Internal MTP Memory Configuration ........................................... 31
Copyright © 2013 Future Technology Devices International Limited
5
FT200XD USB I2C SLAVE IC Datasheet
Version 1.3
Document No.: FT_000628 Clearance No.: FTDI# 265
10.1
Default Values ................................................................................ 31
10.2
Methods of Programming the MTP Memory .................................... 32
10.2.1
Programming the MTP memory over USB .................................................................. 32
10.2.2
Programming the MTP memory over I2C .................................................................... 32
10.3
Memory Map .................................................................................. 33
10.4
Hardware Requirements ................................................................ 34
10.5
Protocol ......................................................................................... 34
11
10.5.1
Address MTP memory (0x10) ................................................................................... 34
10.5.2
Write MTP memory (0x12)....................................................................................... 34
10.5.3
Read MTP memory (0x14) ....................................................................................... 34
10.5.4
Examples of Writing and Reading ............................................................................. 34
Package Parameters ................................................................... 36
11.1
DFN-10 Package Mechanical Dimensions ....................................... 36
11.2
Package Markings .......................................................................... 37
11.3
Solder Reflow Profile ..................................................................... 38
12
Contact Information ................................................................... 39
Appendix A – References ........................................................................... 40
Appendix B - List of Figures and Tables ..................................................... 41
Appendix C - Revision History .................................................................... 42
Copyright © 2013 Future Technology Devices International Limited
6
FT200XD USB I2C SLAVE IC Datasheet
Version 1.3
Document No.: FT_000628 Clearance No.: FTDI# 265
3
Device Pin Out and Signal Description
3V3OUT
1
10
7
USBDM
USBDP
GND
11
9
RESET#
5
CBUS0
GND
2
6
8
SCL
SDA
VCCIO
3
VCC
4
3.1 10-LD DFN Package
Figure 3.1 DFN Schematic Symbol
3.1.1 DFN Package Pin Out Description
Note : # denotes an active low signal.
Pin No.
4
7
3
9
Name
Type
Description
**
POWER
Input
5 V (or 3V3) supply to IC
POWER
Input
1V8 - 3V3 supply for the IO cells
VCC
VCCIO
**
3V3OUT
GND
3V3 output at 50mA. May be used to power VCCIO.
POWER
Output
When VCC is 3V3; pin 3 is an input pin and should be
connected to pin 4.
POWER
Input
0V Ground input.
Table 3.1 Power and Ground
*Pin 11 is the centre pad on the chip package base. This should be connected to GND
** If VCC is 3V3 then 3V3OUT must also be driven with 3V3 input
Pin No.
Name
Type
Description
1
USBDM
INPUT
USB Data Signal Minus.
10
USBDP
INPUT
USB Data Signal Plus.
2
RESET#
INPUT
Reset input (active low).
Table 3.2 Common Function pins
Copyright © 2013 Future Technology Devices International Limited
7
FT200XD USB I2C SLAVE IC Datasheet
Version 1.3
Document No.: FT_000628 Clearance No.: FTDI# 265
Pin No.
Name
Type
Description
8
SDA
I/O
I C bi-directional data line. The signal is open drain.
6
SCL
Input
I C clock input
5
CBUS0
I/O
Configurable CBUS I/O Pin. Function of this pin is configured
in the device MTP memory. See CBUS Signal Options, Table
3.4.
2
2
2
Table 3.3 I C Interface and CBUS Group (see note 1)
Note:
1. When used in Input Mode, the input pins are pulled to VCCIO via internal 75kΩ (approx) resistors.
These pins can be programmed to gently pull low during USB suspend (PWREN# = “1”) by setting an
option in the MTP memory.
2. Clock stretching is not supported
Copyright © 2013 Future Technology Devices International Limited
8
FT200XD USB I2C SLAVE IC Datasheet
Version 1.3
Document No.: FT_000628 Clearance No.: FTDI# 265
3.2 CBUS Signal Options
The following options can be configured on the CBUS I/O pins. These options can be configured in the
internal MTP memory using the software utility FT_PROG, which can be downloaded from the FTDI
Utilities (www.ftdichip.com). The default configuration is noted below and described in Section 10.
CBUS Signal
Option
Available On CBUS Pin
TRI-STATE
CBUS0
IO Pad is tri-stated
DRIVE 1
CBUS0
Output a constant 1
DRIVE 0
CBUS0
Output a constant 0
PWREN#
CBUS0
Output is low after the device has been configured by USB, then
high during USB suspend mode. This output can be used to control
power to external logic P-Channel logic level MOSFET switch. Enable
the interface pull-down option when using the PWREN# in this way.
SLEEP#
CBUS0
Goes low during USB suspend mode. Typically used to power down
an external logic to reduce power consumption.
CLK24MHz
CBUS0
24 MHz Clock output.*
CLK12MHz
CBUS0
12 MHz Clock output.*
CLK6MHz
CBUS0
6 MHz Clock output.*
GPIO
CBUS0
CBUS bit bang mode option. . A separate application note, AN232R01, available from FTDI website(www.ftdichip.com) describes in
more detail how to use CBUS bit bang mode.
BCD Charger
CBUS0
Battery Charge Detect, indicates when the device is connected to a
dedicated battery charger host. Active high output.
BCD Charger#
CBUS0
Inverse of BCD Charger (open drain)
BitBang_WR#
CBUS0
Synchronous and asynchronous bit bang mode WR# strobe output.
BitBang_RD#
CBUS0
Synchronous and asynchronous bit bang mode RD# strobe output.
I2C_TXE#
CBUS0
2
Transmit buffer empty, used to indicate to I C master device status
of the FT200XDtransmit buffer
I2C_RXF#
CBUS0
2
Receive buffer full, used to indicate to I C master device status of
FT200XD receive buffer
VBUS Sense
CBUS0
Input to detect when VBUS is present.
Time Stamp
CBUS0
Toggle signal which changes state each time a USB SOF is received
Keep_Awake#
CBUS0
Prevents the device from entering suspend state when unplugged.
May be used if programming the MTP memory over I 2C
Description
Table 3.4 CBUS Configuration Control
*When in USB suspend mode the outputs clocks are also suspended.
Copyright © 2013 Future Technology Devices International Limited
9
FT200XD USB I2C SLAVE IC Datasheet
Version 1.3
Document No.: FT_000628 Clearance No.: FTDI# 265
4
Function Description
2
2
The FT200XD is a package and pin optimised USB to I C interface device which simplifies USB to I C
designs and reduces external component count by fully integrating an external EEPROM and a clock
circuit which requires no external crystal in a small form factor 3x3mm 10 pin package. It has been
designed to operate efficiently with a USB host controller by using as little of the total USB bandwidth
available as possible.
4.1 Key Features
Functional Integration. Fully integrated MTP memory, clock generation, AVCC filtering, PowerOn_Reset (POR) and LDO regulators.
Configurable CBUS I/O Pin Options. The fully integrated MTP memory allows configuration of the
Control Bus (CBUS) functionality and drive strength selection. There is 1 configurable CBUS I/O pin.
These configurable options are defined in section 3.2.
The device is supplied with the most commonly used pin definitions pre-programmed - see Section 10 for
details.
Asynchronous Bit Bang Mode with RD# and WR# Strobes. The FT200XD supports FTDI’s previous
2
chip generation bit-bang mode. In bit-bang mode, the 2 I C lines can be switched from the regular
interface mode to a 2-bit general purpose I/O port. Data packets can be sent to the device and they will
be sequentially sent to the interface at a rate controlled by an internal timer (equivalent to the baud rate
pre-scalar). In the FT200XD device this mode has been enhanced by outputting the internal RD# and
WR# strobes signals which can be used to allow external logic to be clocked by accesses to the bit-bang
I/O bus. This option will be described more fully in a separate application note available from FTDI
website (www.ftdichip.com).
Synchronous Bit Bang Mode. The FT200XD supports synchronous bit bang mode. This mode differs
from asynchronous bit bang mode in that the interface pins are only read when the device is written to.
This makes it easier for the controlling program to measure the response to an output stimulus as the
data returned is synchronous to the output data. An application note, AN232R-01, available from FTDI
website(www.ftdichip.com) describes this feature.
Low Power Consumption, The FT200XD is capable of operating at a voltage supply between +3.3V and
+5V with a nominal operational mode current of 8mA and a nominal USB suspend mode current of
125µA. This allows greater margin for peripheral designs to meet the USB suspend mode current limit of
2.5mA. An integrated level converter within the I2C interface allows the FT200XD to interface to I2C logic
running at +1.8V to +3.3V (5V tolerant).
4.2 Functional Block Descriptions
The following paragraphs detail each function within the FT200XD. Please refer to the block diagram
shown in Figure 2.1.
Internal MTP Memory. The internal MTP memory in the FT200XD is used to store USB Vendor ID (VID),
Product ID (PID), device serial number, product description string and various other USB configuration
descriptors. The internal MTP memory is also used to configure the CBUS pin functions. The FT200XD is
supplied with the internal MTP memory pre-programmed as described in Section10. A user area of the
internal MTP memory is available to system designers to allow storing of additional data from the user
application over USB. The internal MTP memory descriptors can be programmed in circuit, over USB
without any additional programming voltage requirements. The descriptors can be programmed using the
FTDI utility software called FT_PROG, which can be downloaded from FTDI Utilitieson the FTDI website
2
(www.ftdichip.com). Additionally the MTP memory can be configured over the I C interface.
+1.8V LDO Regulator. The +1.8V LDO regulator generates the +1.8V reference voltage for driving the
internal core of the IC.
+3.3V LDO Regulator. The +3.3V LDO regulator generates the +3.3V reference voltage for driving the
USB transceiver cell output buffers. It requires an external decoupling capacitor to be connected to the
3V3OUT regulator output pin. It also provides +3.3V power to the 1.5kΩ internal pull up resistor on
USBDP. The main function of the LDO is to power the USB Transceiver and the Reset Generator Cells
rather than to power external logic. However, it can be used to supply external circuitry requiring a
+3.3V nominal supply with a maximum current of 50mA.
USB Transceiver. The USB Transceiver Cell provides the USB 1.1 / USB 2.0 full-speed physical interface
to the USB cable. The output drivers provide +3.3V level slew rate control signalling, whilst a differential
Copyright © 2013 Future Technology Devices International Limited
10
FT200XD USB I2C SLAVE IC Datasheet
Version 1.3
Document No.: FT_000628 Clearance No.: FTDI# 265
input receiver and two single ended input receivers provide USB data in, Single-Ended-0 (SE0) and USB
reset detection conditions respectfully. This function also incorporates a 1.5kΩ pull up resistor on USBDP.
The block also detects when connected to a USB power supply which will not enumerate the device but
still supply power and may be used for battery charging.
USB DPLL. The USB DPLL cell locks on to the incoming NRZI USB data and generates recovered clock
and data signals for the Serial Interface Engine (SIE) block.
Internal 12MHz Oscillator - The Internal 12MHz Oscillator cell generates a 12MHz reference clock. This
provides an input to the x4 Clock Multiplier function. The 12MHz Oscillator is also used as the reference
clock for the SIE, USB Protocol Engine and UART FIFO controller blocks.
Clock Multiplier / Divider. The Clock Multiplier / Divider takes the 12MHz input from the Internal
Oscillator function and generates the 48MHz, 24MHz, 12MHz and 6MHz reference clock signals. The
48MHz clock reference is used by the USB DPLL and the Baud Rate Generator blocks.
Serial Interface Engine (SIE). The Serial Interface Engine (SIE) block performs the parallel to serial
and serial to parallel conversion of the USB data. In accordance with the USB 2.0 specification, it
performs bit stuffing/un-stuffing and CRC5/CRC16 generation. It also checks the CRC on the USB data
stream.
USB Protocol Engine. The USB Protocol Engine manages the data stream from the device USB control
endpoint. It handles the low level USB protocol requests generated by the USB host controller and the
commands for controlling the functional parameters of the I2C in accordance with the USB 2.0
specification chapter 9.
FIFO RX Buffer (512 bytes). Data sent from the USB host controller to the I2C interface via the USB
data OUT endpoint is stored in the FIFO RX (receive) buffer. Data is removed from the buffer to the I2C
transmit register under control of the I2C Controller.(RX is relative to the USB interface).
2
FIFO TX Buffer (512 bytes). Data from the I C receive register is stored in the TX buffer. The USB
host controller removes data from the FIFO TX Buffer by sending a USB request for data from the device
data IN endpoint.(TX is relative to the USB interface).
2
I2C Controller. Module to handle the latching in and out of serial data on the I C interface. Supports up
to 3.4MHz, High Speed Serial Mode.
RESET Generator - The integrated Reset Generator Cell provides a reliable power-on reset to the device
internal circuitry at power up. The RESET# input pin allows an external device to reset the FT200XD.
RESET# can be tied to 3V3OUT.
Copyright © 2013 Future Technology Devices International Limited
11
FT200XD USB I2C SLAVE IC Datasheet
Version 1.3
Document No.: FT_000628 Clearance No.: FTDI# 265
5
I2C Interface Description
2
I C (Inter Integrated Circuit) is a multi-master serial bus invented by Philips. I2C uses two bi-directional
open-drain wires called serial data (SDA) and serial clock (SCL). Common I²C bus speeds are the 100
kbit/s standard mode (SM), 400 kbit/s fast mode (FM), 1 Mbit/s Fast mode plus (FM+), and 3.4 Mbit/s
High Speed mode (HS)
An I2C bus node can operate either as a master or a slave:

Master node
– issues the clock and addresses slaves

Slave node
– receives the clock line and address.
The FT200XD device only operates as a slave, and is capable of speeds up to 3.4MBit/s. There are four
potential modes of operation for a given bus device, although most devices only use a single role (Master
or Slave) and its two modes (Transmit and Receive):

Master transmit – sending data to a slave

Master receive – receiving data from a slave

Slave transmit – sending data to a master

Slave receive
– receiving data from the master
The master is initially in master transmit mode by sending a start bit followed by the 7-bit address of the
slave it wishes to communicate with, which is finally followed by a single bit representing whether it
wishes to write(0) to or read(1) from the slave.
If the slave exists on the bus then it will respond with an ACK bit (active low for acknowledged) for that
address. The master then continues in either transmit or receive mode (according to the read/write bit it
sent), and the slave continues in its complementary mode (receive or transmit, respectively).
The address and the data bytes are sent most significant bit first. The start bit is indicated by a high-tolow transition of SDA with SCL high; the stop bit is indicated by a low-to-high transition of SDA with SCL
high.
If the master wishes to write to the slave then it repeatedly sends a byte with the slave sending an ACK
bit. (In this situation, the master is in master transmit mode and the slave is in slave receive mode.)
If the master wishes to read from the slave then it repeatedly receives a byte from the slave, the master
sends an ACK bit after every byte but the last one. (In this situation, the master is in master receive
mode and the slave is in slave transmit mode.)
The master then ends transmission with a stop bit, or it may send another START bit if it wishes to retain
control of the bus for another transfer (a "combined message").
I²C defines three basic types of message, each of which begins with a START and ends with a STOP:

Single message where a master writes data to a slave;

Single message where a master reads data from a slave;

Combined messages, where a master issues at least two reads and/or writes to one or more
slaves
In a combined message, each read or write begins with a START and the slave address. After the first
START, these are also called repeated START bits; repeated START bits are not preceded by STOP bits,
which is how slaves know the next transfer is part of the same message.
Please refer to the I2C specification for more information on the protocol.
Copyright © 2013 Future Technology Devices International Limited
12
FT200XD USB I2C SLAVE IC Datasheet
Version 1.3
Document No.: FT_000628 Clearance No.: FTDI# 265
6
Devices Characteristics and Ratings
6.1 Absolute Maximum Ratings
The absolute maximum ratings for the FT200XD devices are as follows. These are in accordance with the
Absolute Maximum Rating System (IEC 60134). Exceeding these may cause permanent damage to the
device.
Parameter
Value
Unit
Storage Temperature
-65°C to 150°C
Degrees C
Conditions
168 Hours
Floor Life (Out of Bag) At Factory Ambient
(30°C / 60% Relative Humidity)
(IPC/JEDEC JSTD-033A MSL
Level 3
Compliant)*
Ambient Operating Temperature (Power
Applied)
-40°C to 85°C
Degrees C
MTTF FT200XD
TBD
Hours
MTTF FT200XD
TBD
Hours
VCC Supply Voltage
-0.3 to +5.5
V
VCCIO IO Voltage
-0.3 to +4.0
V
DC Input Voltage – USBDP and USBDM
-0.5 to +3.63
V
-0.3 to +5.8
V
22
mA
DC Input Voltage – High Impedance
Bi-directionals (powered from VCCIO)
DC Output Current – Outputs
Hours
Table 6.1 Absolute Maximum Ratings
* If devices are stored out of the packaging beyond this time limit the devices should be baked before
use. The devices should be ramped up to a temperature of +125°C and baked for up to 17 hours.
6.2 ESD and Latch-up Specifications
Description
Specification
Human Body Mode (HBM)
> ± 2kV
Machine mode (MM)
> ± 200V
Charged Device Mode (CDM)
> ± 500V
Latch-up
> ± 200mA
Table 6.2 ESD and Latch-Up Specifications
Copyright © 2013 Future Technology Devices International Limited
13
FT200XD USB I2C SLAVE IC Datasheet
Version 1.3
Document No.: FT_000628 Clearance No.: FTDI# 265
6.3 DC Characteristics
DC Characteristics (Ambient Temperature = -40°C to +85°C)
Parameter
Description
Minimum
Typical
Maximum
Units
Conditions
VCC
VCC Operating Supply
Voltage
2.97
5
5.5
V
Normal Operation
VCC2
VCCIO Operating
Supply Voltage
1.62
---
3.63
V
Icc1
Operating Supply
Current
6.8
8
9.1
mA
Normal Operation
Icc2
Operating Supply
Current
μA
USB Suspend
V
VCC must be
greater than 3V3
otherwise 3V3OUT
is an input which
must be driven
with 3.3V in this
instance pins 3
and 4 of the
package should be
shorted together.
3V3
3.3v regulator output
125
2.97
3.3
3.63
Table 6.3 Operating Voltage and Current
Copyright © 2013 Future Technology Devices International Limited
14
FT200XD USB I2C SLAVE IC Datasheet
Version 1.3
Document No.: FT_000628 Clearance No.: FTDI# 265
Parameter
Description
Minimum
Typical
Maximum
Units
Conditions
2.97
VCCIO
VCCIO
V
2.97
VCCIO
VCCIO
V
I/O Drive strength*
= 8mA
2.97
VCCIO
VCCIO
V
I/O Drive strength*
= 12mA
2.97
VCCIO
VCCIO
V
I/O Drive strength*
= 16mA
0
0.4
V
0
0.4
V
I/O Drive strength*
= 8mA
0
0.4
V
I/O Drive strength*
= 12mA
0
0.4
V
I/O Drive strength*
= 16mA
0.8
V
LVTTL
V
LVTTL
LVTTL
Ioh =-2mA
Voh
Output Voltage High
I/O Drive strength*
= 4mA
Iol = +2mA
Vol
Output Voltage Low
I/O Drive strength*
= 4mA
Vil
Input low Switching
Threshold
Vih
Input High Switching
Threshold
Vt
Switching Threshold
1.49
V
Vt-
Schmitt trigger negative
going threshold voltage
1.15
V
Vt+
Schmitt trigger positive
going threshold voltage
1.64
V
Rpu
Input pull-up resistance
40
75
190
KΩ
Vin = 0
Rpd
Input pull-down
resistance
40
75
190
KΩ
Vin =VCCIO
Iin
Input Leakage Current
-10
+/-1
10
μA
Vin = 0
μA
Vin = 5.5V or 0
2.0
Tri-state output leakage
-10
+/-1
10
current
Table 6.4 I/O Pin Characteristics VCCIO = +3.3V (except USB PHY pins)
Ioz
* The I/O drive strength and slow slew-rate are configurable in the MTP memory.
Copyright © 2013 Future Technology Devices International Limited
15
FT200XD USB I2C SLAVE IC Datasheet
Version 1.3
Document No.: FT_000628 Clearance No.: FTDI# 265
Parameter
Description
Minimum
Typical
Maximum
Units
Conditions
2.25
VCCIO
VCCIO
V
2.25
VCCIO
VCCIO
V
I/O Drive strength*
= 8mA
2.25
VCCIO
VCCIO
V
I/O Drive strength*
= 12mA
2.25
VCCIO
VCCIO
V
I/O Drive strength*
= 16mA
Ioh = +/-2mA
Voh
Output Voltage High
I/O Drive strength*
= 4mA
Iol = +/-2mA
Vol
Output Voltage Low
0
0.4
V
0
0.4
V
I/O Drive strength*
= 8mA
0
0.4
V
I/O Drive strength*
= 12mA
0
0.4
V
I/O Drive strength*
= 16mA
0.8
V
LVTTL
V
LVTTL
LVTTL
I/O Drive strength*
= 4mA
Vil
Input low Switching
Threshold
Vih
Input High Switching
Threshold
Vt
Switching Threshold
1.1
V
Vt-
Schmitt trigger negative
going threshold voltage
0.8
V
Vt+
Schmitt trigger positive
going threshold voltage
1.2
V
Rpu
Input pull-up resistance
40
75
190
KΩ
Vin = 0
Rpd
Input pull-down
resistance
40
75
190
KΩ
Vin =VCCIO
Iin
Input Leakage Current
-10
+/-1
10
μA
Vin = 0
μA
Vin = 5.5V or 0
0.8
Tri-state output leakage
-10
+/-1
10
current
Table 6.5 I/O Pin Characteristics VCCIO = +2.5V (except USB PHY pins)
Ioz
* The I/O drive strength and slow slew-rate are configurable in the MTP memory.
Copyright © 2013 Future Technology Devices International Limited
16
FT200XD USB I2C SLAVE IC Datasheet
Version 1.3
Document No.: FT_000628 Clearance No.: FTDI# 265
Parameter
Description
Minimum
Typical
Maximum
Units
Conditions
1.62
VCCIO
VCCIO
V
1.62
VCCIO
VCCIO
V
I/O Drive strength*
= 8mA
1.62
VCCIO
VCCIO
V
I/O Drive strength*
= 12mA
1.62
VCCIO
VCCIO
V
I/O Drive strength*
= 16mA
Ioh = +/-2mA
Voh
Output Voltage High
I/O Drive strength*
= 4mA
Iol = +/-2mA
Vol
Output Voltage Low
0
0.4
V
0
0.4
V
I/O Drive strength*
= 8mA
0
0.4
V
I/O Drive strength*
= 12mA
0
0.4
V
I/O Drive strength*
= 16mA
0.77
V
LVTTL
V
LVTTL
LVTTL
I/O Drive strength*
= 4mA
Vil
Input low Switching
Threshold
Vih
Input High Switching
Threshold
Vt
Switching Threshold
0.77
V
Vt-
Schmitt trigger negative
going threshold voltage
0.557
V
Vt+
Schmitt trigger positive
going threshold voltage
0.893
V
Rpu
Input pull-up resistance
40
75
190
KΩ
Vin = 0
Rpd
Input pull-down
resistance
40
75
190
KΩ
Vin =VCCIO
Iin
Input Leakage Current
-10
+/-1
10
μA
Vin = 0
μA
Vin = 5.5V or 0
1.6
Tri-state output leakage
-10
+/-1
10
current
Table 6.6 I/O Pin Characteristics VCCIO = +1.8V (except USB PHY pins)
Ioz
* The I/O drive strength and slow slew-rate are configurable in the MTP memory.
Copyright © 2013 Future Technology Devices International Limited
17
FT200XD USB I2C SLAVE IC Datasheet
Version 1.3
Document No.: FT_000628 Clearance No.: FTDI# 265
Parameter
Description
Minimum
Voh
Output Voltage High
VCC-0.2
Vol
Output Voltage Low
Vil
Input low Switching
Threshold
Vih
Input High Switching
Threshold
Typical
Maximum
Units
Conditions
V
-
0.2
V
0.8
V
-
2.0
V
Table 6.7 USB I/O Pin (USBDP, USBDM) Characteristics
6.4 MTP Memory Reliability Characteristics
The internal 2048 Byte MTP Memory has the following reliability characteristics:
Parameter
Value
Unit
Data Retention
10
Years
Write Cycle
Read Cycle
2,000
Cycles
minimum
Unlimited
Cycles
Table 6.8 MTP Memory Characteristics
6.5 Internal Clock Characteristics
The internal Clock Oscillator has the following characteristics:
Value
Parameter
Unit
Minimum
Typical
Maximum
Frequency of Operation
(see Note 1)
11.98
12.00
12.02
MHz
Clock Period
83.19
83.33
83.47
ns
Duty Cycle
45
50
55
%
Table 6.9 Internal Clock Characteristics
Note 1: Equivalent to +/-1667ppm
Copyright © 2013 Future Technology Devices International Limited
18
FT200XD USB I2C SLAVE IC Datasheet
Version 1.3
Document No.: FT_000628 Clearance No.: FTDI# 265
7
USB Power Configurations
The following sections illustrate possible USB power configurations for the FT200XD.
7.1 USB Bus Powered Configuration
VCC
Ferrite
Bead
1
VCC
27R
2
USBDM
3
27R
USBDP
4
FT200XD
5
SHIELD
47pF
47pF
RESET#
10nF
VCCIO
GND
GND
VCC
GN
D
AG
ND
3V3OUT
100nF
+
4.7uF
100nF
GND
GND
Figure 7.1 Bus Powered Configuration
Figure 7.1Illustrates the FT200XD in a typical USB bus powered design configuration. A USB bus powered
device gets its power from the USB bus. Basic rules for USB bus power devices are as follows –
i)
ii)
iii)
iv)
v)
On plug-in to USB, the device must draw no more current than 100mA.
In USB Suspend mode the device must draw no more than 2.5mA.
A bus powered high power USB device (one that draws more than 100mA) should use the
CBUS pins configured as PWREN# and use it to keep the current below 100mA on plug-in and
2.5mA on USB suspend. Using the CBUS pin for PWREN# prevents the FT200XD from
indicating a USB Battery Charger is connected.
A device that consumes more than 100mA cannot be plugged into a USB bus powered hub.
No device can draw more than 500mA from the USB bus.
The power descriptors in the internal MTP Memory of the FT200XDmustbe programmed to match the
current drawn by the device.
A ferrite bead is connected in series with the USB power supply to reduce EMI noise from the FT200XD
and associated circuitry being radiated down the USB cable to the USB host. The value of the Ferrite
Bead depends on the total current drawn by the application. A suitable range of Ferrite Beads is available
from Laird Technologies (http://www.lairdtech.com), for example Laird Technologies Part #
MI0805K601R-10.
Note: If using PWREN# (available using the CBUS) the pin must be pulled to VCCIO using a 10kΩ
resistor.
Copyright © 2013 Future Technology Devices International Limited
19
FT200XD USB I2C SLAVE IC Datasheet
Version 1.3
Document No.: FT_000628 Clearance No.: FTDI# 265
7.2 Self Powered Configuration
VCC(3.3-5.25V)
1
VCC
27R
2
USBDM
27R
3
USBDP
4
47pF
4k7
47pF
FT200XD
5
VBUS_SENSE#
SHIELD
RESET#
VCCIO
10k
3V3OUT
AG
ND
GND
GND
GN
D
GND
VCC
100nF
100nF
100nF
+
4.7uF
GND
GND
Figure 7.2 Self Powered Configuration
Figure 7.2 illustrates the FT200XD in a typical USB self powered configuration. A USB self powered device
gets its power from its own power supply, VCC, and does not draw current from the USB bus. The basic
rules for USB self powered devices are as follows –
i)
ii)
iii)
A self powered device must not force current down the USB bus when the USB host or hub
controller is powered down.
A self powered device can use as much current as it needs during normal operation and USB
suspend as it has its own power supply.
A self powered device can be used with any USB host, a bus powered USB hub or a self
powered USB hub.
The power descriptor in the internal MTP memory of the FT200XD should be programmed to a value of
zero (self powered).
In order to comply with the first requirement above, the USB bus power (pin 1) is used to control the
VBUS_Sense pin of the FT200XD device. When the USB host or hub is powered up an internal 1.5kΩ
resistor on USBDP is pulled up to +3.3V, thus identifying the device as a full speed device to the USB
host or hub. When the USB host or hub is powered off, VBUS_Sense pin will be low and the FT200XDis
held in a suspend state. In this state the internal 1.5kΩ resistor is not pulled up to any power supply
(hub or host is powered down), so no current flows down USBDP via the 1.5kΩ pull-up resistor. Failure to
do this may cause some USB host or hub controllers to power up erratically.
Figure 7.2 illustrates a self powered design which has a +3.3V to +5.25V supply.
Note:
1. When the FT200XD is in reset, the interface I/O pins are tri-stated. Input pins have internal
200kΩ pull-up resistors to VCCIO, so they will gently pull high unless driven by some external
logic.
Copyright © 2013 Future Technology Devices International Limited
20
FT200XD USB I2C SLAVE IC Datasheet
Version 1.3
Document No.: FT_000628 Clearance No.: FTDI# 265
7.3 USB Bus Powered with Power Switching Configuration
P Channel Power
MOSFET
Switched 5V Power to
External Logic
0.1uF
10k
0.1uF
1k
PWREN#
Ferrite
Bead
1
VCC
27R
2
USBDM
3
27R
USBDP
4
47pF
FT200XD
5
47pF
RESET#
SHIELD
VCCIO
10nF
GND
VCC
CBUS0
GN
D
AG
ND
3V3OUT
GND
100nF
+
4.7uF
100nF
GND
GND
Figure 7.3 Bus Powered with Power Switching Configuration
A requirement of USB bus powered applications, is when in USB suspend mode, the application draws a
total current of less than 2.5mA. This requirement includes external logic. Some external logic has the
ability to power itself down into a low current state by monitoring the PWREN# signal. For external logic
that cannot power itself down in this way, the FT200XD provides a simple but effective method of turning
off power during the USB suspend mode.
Figure 7.3 shows an example of using a discrete P-Channel MOSFET to control the power to external
logic. A suitable device to do this is an International Rectifier (www.irf.com) IRLML6402, or equivalent. It
is recommended that a “soft start” circuit consisting of a 1kΩ series resistor and a 0.1μF capacitor is used
to limit the current surge when the MOSFET turns on. Without the soft start circuit it is possible that the
transient power surge, caused when the MOSFET switches on, will reset the FT200XD or the USB
host/hub controller. The soft start circuit example shown in Figure 7.3 powers up with a slew rate of
approximaely12.5V/ms. Thus supply voltage to external logic transitions from GND to +5V in
approximately 400 microseconds.
As an alternative to the MOSFET, a dedicated power switch IC with inbuilt “soft-start” can be used. A
suitable power switch IC for such an application is the Micrel (www.micrel.com) MIC2025-2BM or
equivalent.
With power switching controlled designs the following should be noted:
i)
The external logic to which the power is being switched should have its own reset circuitry to
automatically reset the logic when power is re-applied when moving out of suspend mode.
ii) Set the Pull-down on Suspend option in the internal FT200XD MTP memory.
iii) The CBUS Pin should be configured as PWREN# in the internal FT200XD MTP memory, and used
to switch the power supply to the external circuitry. Detection of a USB battery charger port is
not possible.
iv) For USB high-power bus powered applications (one that consumes greater than 100mA, and up
to 500mA of current from the USB bus), the power consumption of the application must be set in
the Max Power field in the internal FT200XD MTP memory. A high-power bus powered application
uses the descriptor in the internal FT200XD MTP memory to inform the system of its power
requirements.
v) PWREN# gets its VCC from VCCIO. For designs using 3V3 logic, ensure VCCIO is not powered
down using the external logic. In this case use the +3V3OUT.
Copyright © 2013 Future Technology Devices International Limited
21
FT200XD USB I2C SLAVE IC Datasheet
Version 1.3
Document No.: FT_000628 Clearance No.: FTDI# 265
8
Application Examples
The following sections illustrate possible applications of the FT200XD.
8.1 USB to I2C Converter
VCC
Ferrite
Bead
1
VCC
SCL
USBDM
SDA
SCL
27R
2
3
I2C MASTER DEVICE
SDA
27R
USBDP
4
47pF
47pF
FT200XD
5
1k
RESET#
SHIELD
1k
VCCIO
VCCIO
10nF
GND
VCC
GN
D
AG
ND
3V3OUT
GND
100nF
+
4.7uF
100nF
GND
GND
2
Figure 8.1 Application Example showing USB to I C Converter
2
An example of using the FT200XD as an I C peripheral is shown in Figure 8.1. The FT200XD is the slave
2
on the I C bus.
2
Therefore the clock supplied to the SCL pin must come from the I C Master. The device will support
2
standard I C data rates such as 100 kbit/s standard mode (SM), 400 kbit/s fast mode (FM), 1 Mbit/s Fast
mode plus (FM+), and 3.4 Mbit/s High Speed mode (HS).
The data line SDA is bi-directional.
The master is initially in master transmit mode by sending a start bit followed by the 7-bit address of the
slave it wishes to communicate with, which is finally followed by a single bit representing whether it
wishes to write(0) to or read(1) from the slave.
If the slave (FT200XD) exists on the bus then it will respond with an ACK bit (active low for
acknowledged) for that address. The master then continues in either transmit or receive mode (according
to the read/write bit it sent), and the slave continues in its complementary mode (receive or transmit,
respectively).
The address and the data bytes are sent most significant bit first. The start bit is indicated by a high-tolow transition of SDA with SCL high; the stop bit is indicated by a low-to-high transition of SDA with SCL
high.
If the master wishes to write to the slave then it repeatedly sends a byte with the slave sending an ACK
bit. (In this situation, the master is in master transmit mode and the slave is in slave receive mode.)
If the master wishes to read from the slave then it repeatedly receives a byte from the slave, the master
sending an ACK bit after every byte but the last one. (In this situation, the master is in master receive
mode and the slave is in slave transmit mode.)
The master then ends transmission with a stop bit, or it may send another START bit if it wishes to retain
control of the bus for another transfer (a "combined message").
I²C defines three basic types of message, each of which begins with a START and ends with a STOP:

Single message where a master writes data to a slave;

Single message where a master reads data from a slave;
Copyright © 2013 Future Technology Devices International Limited
22
FT200XD USB I2C SLAVE IC Datasheet
Version 1.3
Document No.: FT_000628 Clearance No.: FTDI# 265
Combined messages, where a master issues at least two reads and/or writes to one or more
slaves

In a combined message, each read or write begins with a START and the slave address. After the first
START, these are also called repeated START bits; repeated START bits are not preceded by STOP bits,
which is how slaves know the next transfer is part of the same message.
2
The I C address of the FT200XD is stored in the device internal MTP memory.
2
Please refer to the I C specification for more information on the protocol.
8.2 USB Battery Charging Detection
A recent addition to the USB specification
(http://www.usb.org/developers/devclass_docs/BCv1.2_011912.zip) is to allow for additional charging
profiles to be used for charging batteries in portable devices. These charging profiles do not enumerate
the USB port of the peripheral. The FT200XD device will detect that a USB compliant dedicated charging
port (DCP) is connected. Once detected while in suspend mode a battery charge detection signal is
provided to allow external logic to switch to charging mode as opposed to operation mode.
VBUS
3V3OUT
VBUS
VBUS
DD+
ID
GND
1
2
3
4
5
VBUS
0.1uF
GND
DM
DP
27R
27R
3V3OUT
0.1uF
VCCIO
3V3OUT
VCC
600R/2A
CN USB
3V3OUT
GND
RESET#
10nF
N.F.
GND
GND
0.1uF
0R
BCD
CBUS0
FT200XD
SLD
GND
GND
GND
VBUS VBUS
4.7uF
0.1uF
GND
3V3OUT
10K
GND
VBUS
3V3OUT
10K
10K
1
2
3
4
5
GND
CHRG
VCC
FAULT
TIMER
GND
ACPR
BAT
SHDN
PROG
NTC
GND
0.1uF
VBATT
10
9
8
7
6
1
+
NCT
TB3.5mm
BCD
NTC
LTC4053EDD
11
2K2
1uF
1K5
1R
GND
GND
GND
GND
GND
EEPROM Setting
X-Chip Pin
CBUS0
Function
BCD
Battery Options
Battery Charger Enable X
Force Power Enable
GND GND
1A when connected to a dedicated charger port
0A when enumerated
0A when not enumerated and not in sleep
0A when in sleep
VBUS
NTC
JP1
NCT Available
4K32 1%
De-acticate Sleep
JUMPER-2mm
JP1
SIP-3
1-2
2-3
NCT Enabled
NCT Disabled (Default)
GND
Figure 8.2 USB Battery Charging Detection
To use the FT200XD with battery charging detection the CBUS pins must be reprogrammed to allow for
the BCD Charger output to switch the external charger circuitry on. The CBUS pins are configured in the
Copyright © 2013 Future Technology Devices International Limited
23
FT200XD USB I2C SLAVE IC Datasheet
Version 1.3
Document No.: FT_000628 Clearance No.: FTDI# 265
internal MTP memory with the free utility FTPROG. If the charging circuitry requires an active low signal
to enable it, the CBUS pin can be programmed to BCD Charger# as an alternative.
When connected to a USB compliant dedicated charging port (DCP, as opposed to a standard USB host)
the device USB signals will be shorted together and the device suspended. The BCD charger signal will
bring the LTC4053 out of suspend and allow battery charging to start. The charge current in the example
above is 1A as defined by the resistance on the PROG pin.
To calculate the equivalent resistance on the PROG pin select a charge current, then Res = 1500V/Ichg
For more configuration options of the LTC4053 refer to:
AN_175_Battery Charging Over USB
Note: If the FT200XD is connected to a standard host port such that the device is enumerated the battery
charge detection signal is inactive as the device will not be in suspend.
Copyright © 2013 Future Technology Devices International Limited
24
FT200XD USB I2C SLAVE IC Datasheet
Version 1.3
Document No.: FT_000628 Clearance No.: FTDI# 265
9
USB and I2C Interfacing
This section covers the transfer of data from USB to I2C and vice versa.
Please note that the FT200XD and FT201X are I2C slave devices only and should be interfaced to an I2C
host (often in a microcontroller or FPGA). If an I2C master is required, please see the FT232H, FT2232H,
FT4232H and FT2232D devices.
This section covers transfer of data only. The USB and I2C interfaces on the FT200XD and FT201X can
also be used for programming of the MTP memory, which is covered in a separate section.
Throughout this section, the reference FT-X applies to the FT200XD and FT201X devices, as the other
members of the FT-X family do not have I2C interfaces.
9.1 Host Interface (USB)
From the host computer’s point of view, the I2C data can be sent and received in the same way as when
interfacing to one of the standard UART devices such as the FT232R. The FT-X handles the entire I2C
protocol inside the chip and so reading and writing data does not require any special programming from
the PC side. It can be treated as a simple data bridge.
9.1.1 VCP and D2xx Interfaces
Like the other FTDI devices, the host can use D2xx commands or can use a Virtual COM Port (VCP) to
communicate with the device.
D2xx Interface
The D2xx method allows the application software to use the functions in the FTDI D2xx library to
communicate directly with the device. This is a library provided free-of-charge by FTDI and is available
within the driver download files at the link below.
http://www.ftdichip.com/Drivers/D2XX.htm
It includes functions to find the FTDI devices on the system, open a particular device, send data to the
device and read data from the device. Any data written using FT_Write, for example, will be sent to the
FT-X chip and will be available for the external I2C Master to read. As mentioned above, only the data
itself needs to be sent as the FT-X handles all of the I2C specific protocol.
There are many other functions available, and full details can be found in the D2xx Programmers Guide.
http://www.ftdichip.com/Support/Documents/ProgramGuides/D2XX_Programmer's_Guide(FT_000071).pd
f
Virtual COM Port Interface
If using the Virtual Com Port (VCP), the device will appear as if it were a real COM port on the computer.
This is useful where an application has already been written to use an RS232 port on the computer as it
allows that application to treat the FT-X as if it were a real COM port. This port can be opened in a
terminal program or a custom application in the same way as a serial port would be opened. Data can
then be sent or received using standard serial / COM port functions.
No I2C decoding is required as the chip itself handles the I2C protocol. Because of this, even I2C versions
of the FT-X family can be used with the VCP interface. Any data which the host PC sends to the Virtual
COM Port (for example, typed into the terminal window in HyperTerminal) will be sent over USB to the
FT-X and can then be read by the external I2C Master. Likewise, any data written to the FT-X over I2C will
be sent to the PC where the terminal program will display it.
Since the FT-X is the I2C slave and does not generate a clock signal, the settings such as baud rate and
handshaking do not have any effect.
Copyright © 2013 Future Technology Devices International Limited
25
FT200XD USB I2C SLAVE IC Datasheet
Version 1.3
Document No.: FT_000628 Clearance No.: FTDI# 265
D2xx and VCP Interface under Windows
In Windows systems, the VCP driver is actually an additional layer on top of the D2xx driver. The D2xx
driver is always loaded and the VCP later may or may not be loaded on top of it, depending on the
requirements of the application.
When VCP is disabled, the device will appear only under Universal Serial Bus Controllers in the Device
Manager and no COM port is exposed. When the VCP is enabled, the device will appear under both the
Universal Serial Bus Controllers and the Ports (COM & LPT) sections in Device Manager.
The VCP interface will be disabled by default in the FT200XD and FT201X but can be enabled in one of
the following ways:
-
-
-
An option bit in the MTP memory on the chip is checked each time that the device is enumerated,
and can cause the host computer to load the VCP layer. This allows each individual hardware unit
to enable or disable VCP as per it’s requirements. The MTP information in section 10 has further
details. FT_Prog can also be used to modify the MTP settings.
The user may open the Properties for the device under Universal Serial Bus Controllers in Device
Manager in Windows and tick a box to load the VCP. Re-enumeration of the FT-X is necessary to
enable the new setting.
By editing the driver FtdiBus.inf file (please refer to AN_107 below). Note that the FT_INF utility
available from the FTDI website can be used to help create the modifed inf files.
http://www.ftdichip.com/Support/Documents/AppNotes/AN_107_AdvancedDriverOptions_AN_00
0073.pdf
In other Operating systems (e.g. Linux, Mac and Windows CE), there are separate drivers for D2xx and
VCP, and only one of these drivers may be installed at any time. Therfore, the mode is selected by
installing the associated driver instead and the selection defined in the bullet points above has no effect.
9.1.2 Reading and Writing Data
Data from FT-X to the Host
When data is to be sent from the host computer to the external I2C master, the software application
writes this data to the FTDI driver using VCP or D2xx and this data is sent by the driver over USB to the
buffer in the device.
The external I2C master device may then perform an I2C read (Master receiver, Slave transmitter)
operation to retrieve the data.
The external I2C master should check if data is available to ensure that the data which has been read is
valid. The methods for this are described in section 9.2.2 below.
Data from Host to the FT-X
When data is to be sent from the external I2C master to the host computer, the external master performs
an I2C write (Master transmitter, Slave receiver) operation to the FT-X.
The FT-X stores this in its buffer and the data is sent back to the driver on the host computer over USB.
As with other FTDI devices, this happens when either the buffer in the device fills or when the latency
timer rolls over (so that partially filled buffers do not wait indefinitely), whichever happens first.
Note that when writing data to the FT-X over I2C, the external master should check whether there is
space available in the buffer inside the FT-X. It can do this using the methods shown in section 9.2.2
below.
The host computer application can then read the data from the driver buffer using the VCP interface or
the D2xx commands. In the case of D2xx, the number of bytes available may be determined using the
FT_GetQueueStatus command before doing the FT_Read.
Copyright © 2013 Future Technology Devices International Limited
26
FT200XD USB I2C SLAVE IC Datasheet
Version 1.3
Document No.: FT_000628 Clearance No.: FTDI# 265
9.2 I2C Interface
From an I2C point of view, the FT-X behaves as a standard I2C slave. Data transfers take the same form
as a standard I2C communication. In addition to reading and writing, there are some other commands
which can be used to determine the status of the device and these are covered in this section and in
further detail in section 9.3.
Note: This section uses 7-bit addressing in the examples. It uses eight characters to describe the seven
address bits and the single read/write bit. For example, 1110 011 1 means address 0x73 with the
Read/Write bit set to 1, and therefore corresponds to a read of address 0x73. Data values are
represented in bytes, for example, 1010 0101 for data value 0xA5.
9.2.1 Addressing
The FT-X can be given a custom slave address on the I2C bus. This is stored in MTP memory and can be
re-programmed over USB or I2C. Please see the separate MTP Programming information in section 10.
The slave address is used when reading and writing to the device. The FT-X supports both 7-bit and 10bit addressing.
The general call address (0000 000 0) is for addressing every device on the bus. Some slaves do not
support the General Call Address though the FT-X devices do support it. They will acknowledge this
address, receive the second byte and interpret it. There are several commands available for this second
byte. The FT-X will support the Software Reset command which is part of the I2C specification as well as
other custom FTDI commands. These are covered in more detail later in the Other I2C Commands
section.
9.2.2 Data Transfers
Reading and Writing
For all I2C data transfers to and from the FT-X, the slave address of the FT-X is used. The figure below
shows a typical 7-bit address transfer for each direction.
Figure 9.1: Data transfers using 7-bit addressing
The figure below summarises all of the transfers available (7-bit and 10-bit addressing).
Copyright © 2013 Future Technology Devices International Limited
27
FT200XD USB I2C SLAVE IC Datasheet
Version 1.3
Document No.: FT_000628 Clearance No.: FTDI# 265
Figure 9.2: Data transfers with 7-bit and 10-bit addressing modes
Flow Control when Reading
When reading data, it is important to know if there is data available to read over I2C and if the data read
is valid. There are three methods by which to check whether the data being read is valid.
-
-
Checking the I2C_TXE# line, which indicates whether the transmit buffer is empty. This signal
can be mapped to the CBUS pins. This line does not indicate the number of bytes available. If the
line is asserted, there are one or more bytes in the transmit buffer. Note that the Transmit buffer
is the buffer which holds data which has come from the host computer and is going to be read by
the external I2C master.
Do a read over I2C (Master receiver, Slave transmitter) and check whether the FT-X
acknowledges the address phase. The FT-X will NAK the address phase if there is no data to read.
If bursting data, then there is not an address phase for each byte. In this case, it is not possible
to tell when the buffer has emptied and therefore when you are no longer reading valid bytes. In
this case, a Data Available check can be carried out first. If the byte after the general call address
is 0x0C (0000 1100), the FT-X returns the Data Available Count to indicate the number of bytes
available for burst read. Please also refer to section 9.3. Note that because this returns a single
byte, the maximum value is 0xFF, and so a value of 0xFF indicates that there are 255 or more
bytes available.
Figure 9.3: Checking the Data Available Count
Flow Control when Writing
When writing data (data going from I2C toward the host computer), it is important to check if there is
space available and if the FT-X accepted the byte written. There are two methods by which to check
whether space is available.
-
Check the I2C_RXF# line, which indicates whether the Receive buffer is full. This line indicates
that there is at least one empty byte available in the buffer. However, there is no indication of
Copyright © 2013 Future Technology Devices International Limited
28
FT200XD USB I2C SLAVE IC Datasheet
Version 1.3
Document No.: FT_000628 Clearance No.: FTDI# 265
-
how many bytes are available. This signal can be mapped to the CBUS pins. Note that the
Receive buffer is the buffer which holds data which has come from the external I2C master and is
going to the host computer over USB.
Do a write over I2C (Master transmitter, Slave receiver) and check if the FT-X ACKs. The FT-X will
NAK if there is no space in the buffer for the data to be written into. The FT-X will NACK in the
address phase if this is the first byte being written and there is no space available. If the buffer
becomes full during a burst write, the FT-X will NACK any bytes during the data phase which
cannot be accommodated in the buffer.
Note that because the acknowledgement can be checked for each byte written (since the FT-X slave is
generating the acknowledge when writing to it), there is no command to ask the FT-X how much buffer
space is available.
9.3 Other I2C Commands
Soft reset
This uses the General Call Address. If the second byte is 0x06 (0000 0110) it will be interpreted by the
FT-X as the Soft Reset command. This will reset the chip and clear all buffers.
Flush command
This uses the General Call Address. If the second byte is 0x0E (0000 1110) it will be interpreted by the
FT-X as the Flush command and the Transmit and Receive buffers will be flushed of all data.
Figure 9.4: Flush data command
Read Data Available command
This uses the General Call Address. If the second byte is 0x0C (0000 1100) it will be interpreted by the
block as the Read Data Available command and on the next I2C read cycle following this command, the
data will hold the number of bytes available for burst read.
Figure 9.5: Reading the amount of data available
USB State command
This uses the General Call Address. If the second byte is 0x16 (0001 0110) it will be interpreted by the
block as the USB State command and on the next read cycle following this command, the data will hold
the coded USB State value. The USB state allows you to check the current USB enumeration state:
0x00 = Suspended.
0x01 = Default.
0x02 = Addressed.
0x03 = Configured.
Note: The Configured state is the normal operating state.
Copyright © 2013 Future Technology Devices International Limited
29
FT200XD USB I2C SLAVE IC Datasheet
Version 1.3
Document No.: FT_000628 Clearance No.: FTDI# 265
Further details of these states can be found in Chapter 9 of the USB 2.0 Specification from the USB
Implementers Forum website (http://www.usb.org).
Figure 9.6: Checking the USB State
Device ID command
This command uses the Slave address of the FT-X. The master issues the 1111 100 0 command (0x7c
write) followed by the slave address with the direction bit as either 0 or 1 (don’t care). The master then
sends a repeated start followed by the 1111 100 1 command (0x7c read). The FT-X responds with 3
bytes containing the manufacturer ID (12 bits), part ID (9 bits) and revision (3 bits). The master ends
reading with a NACK.
Note: In the case where the master keeps ACKing the data, it has to wrap around and the slave (the FTX) will keep sending the 3 bytes of its ID.
Figure 9.7: Reading the Device ID
Copyright © 2013 Future Technology Devices International Limited
30
FT200XD USB I2C SLAVE IC Datasheet
Version 1.3
Document No.: FT_000628 Clearance No.: FTDI# 265
10 Internal MTP Memory Configuration
The FT200XD includes an internal MTP memory which holds the USB configuration descriptors, other
configuration data for the chip and also user data areas. Following a power-on reset or a USB reset the
FT200XD will scan its internal MTP memory and read the USB configuration descriptors stored there
In many cases, the default values programmed into the MTP memory will be suitable and no reprogramming will be necessary. The defaults can be found in Section 10.1.
The MTP memory in the FT200XD can be programmed over USB or over the I2C bus if the values need to
be changed for a particular application. Further details of this are provided from section 10.2 onwards.
Users who do not have their own USB Vendor ID but who would like to use a unique Product ID in their
design can apply to FTDI for a free block of unique PIDs. See TN_100 – USB Vendor ID/Product ID
Guidelines for more details.
10.1 Default Values
The default factory programmed values of the internal MTP memory are shown in the following table:
Parameter
Value
Notes
USB Vendor ID (VID)
0403h
FTDI default VID (hex)
USB Product UD (PID)
6015h
FTDI default PID (hex)
Serial Number Enabled
Yes
Serial Number
See Note
A unique serial number is generated and
programmed into the MTP memory during device
final test.
Enabling this option will make the device pull down
Pull down I/O Pins in USB
Suspend
Disabled
Manufacturer Name
FTDI
Product Description
FT200XD USB I2C
Max Bus Power Current
90mA
Power Source
Bus Powered
Device Type
FT200XD
2
on the I C and CBUS0 pins when in USB suspend
mode (PWREN# is high).
Returns USB 2.0 device description to the host.
Note: The device is a USB 2.0 Full Speed device
(12Mb/s) as opposed to a USB 2.0 Hi-Speed device
(480Mb/s).
USB Version
0200
Remote Wake Up
Disabled
DBUS Drive Current
Strength
4mA
Options are 4mA, 8mA, 12mA, 16mA
DBUS slew rate
Slow
Options are slow or fast
DBUS Schmitt Trigger
Normal
Options are normal or Schmitt
Copyright © 2013 Future Technology Devices International Limited
31
FT200XD USB I2C SLAVE IC Datasheet
Version 1.3
Document No.: FT_000628 Clearance No.: FTDI# 265
Enable
CBUS Drive Current
Strength
4mA
Options are 4mA, 8mA, 12mA, 16mA
CBUS slew rate
Slow
Options are slow or fast
CBUS Schmitt Trigger
Enable
Normal
Options are normal or Schmitt
Load VCP Driver
Disabled
I2C Address
22h
I2C Device ID
CBUS0
Enabling this will load the VCP driver interface for
the device.
The I2C device address
The I2C device ID
Keep_Awake#
Prevents the device from entering suspend state
when unplugged. May be used if programming the
MTP memory over I2C
Table 10.1 Default Internal MTP memory Configuration
10.2 Methods of Programming the MTP Memory
10.2.1
Programming the MTP memory over USB
The MTP memory on all FT-X devices can be programmed over USB. This method is the same as for the
EEPROM on other FTDI devices such as the FT232R. No additional hardware, connections or programming
voltages are required. The device is simply connected to the host computer in the same way that it would
be for normal applications, and the FT_Prog utility is used to set the required options and program the
device.
The FT_Prog utility is provided free-of-charge from the FTDI website, and can be found at the link below.
The user guide is also available at this link.
http://www.ftdichip.com/Support/Utilities.htm#FT_Prog
Additionally, D2XX commands can be used to program the MTP memory from within user applications.
For more information on the commands available, please see the D2XX Programmers Guide below.
http://www.ftdichip.com/Support/Documents/ProgramGuides/D2XX_Programmer's_Guide(FT_000071).p
df
10.2.2
Programming the MTP memory over I2C
In the FT200XD device, it is possible to program the MTP memory over its I2C interface. This is the same
interface which is used in the normal application of the FT200XD and would normally be connected to the
I2C master implemented in a microcontroller (MCU) or FPGA. However, special commands can also be
used to access the MTP memory in the FT200XD over the same I2C connection, allowing the MCU/FPGA to
read and write locations in the MTP memory. No additional hardware, connections or programming
voltages are required.
Two examples where it may be desired to use the I2C interface to write and read the MTP Memory are
given below. In some cases, the application may use both of these possibilities.
1. To store and retrieve application specific data such as calibration constants in the user area (e.g.
if the overall application was an analog measurement system). This can avoid the need for an
extra EEPROM chip on the application board.
2. To read and write the configuration data (e.g. custom VID, PID, description strings or CBUS
signal selection to enable signals for battery charging etc) without a USB host. This could allow an
MCU/FPGA to configure the FT200XD during production testing of the finished device or even
when in use in the field.
Copyright © 2013 Future Technology Devices International Limited
32
FT200XD USB I2C SLAVE IC Datasheet
Version 1.3
Document No.: FT_000628 Clearance No.: FTDI# 265
The information in the rest of this chapter can be used to implement the storing and reading of
application data in the user area as in example 1 above. Example 2 requires details of the configuration
data stored in the MTP memory. Further details can be found in the following application note:
http://www.ftdichip.com/Support/Documents/AppNotes/AN_201_FTX%20MTP%20Memory%20Configuration.pdf
10.3 Memory Map
The FT-X family MTP memory has various areas which come under three main categories:



User Memory Area
Configuration Memory Area (writable)
Configuration Memory Area (non-writable)
Memory Area Description
Word Address
User Memory Area 2
Accessible via USB, I2C and FT1248
0x3FF - 0x80
Configuration Memory Area
Accessible via USB, I2C and FT1248
0x7E - 0x50
Configuration Memory Area
Cannot be written
0x4E - 0x40
User Memory Area 1
Accessible via USB, I2C and FT1248
0x3E - 0x12
Configuration Memory Area
Accessible via USB, I2C and FT1248
0x10 - 0x00
Figure 10.1 Simplified memory map for the FT-X
User Memory Area
The User Memory Areas are highlighted in Green on the memory map. They can be read and written via
both USB and I2C. All locations within this range are freely programmable; no areas have special
functions and there is no checksum for the user area.
Note that the application should take into account the specification for the number of write cycles in
Section 6.4 if it will be writing to the MTP memory multiple times.
Configuration Memory Area (writable)
This area stores the configuration data for the device, including the data which is returned to the host in
the configuration descriptors (e.g. the VID, PID and string descriptions) and also values which set the
hardware configuration (the signal assigned to each CBUS pin for example).
Copyright © 2013 Future Technology Devices International Limited
33
FT200XD USB I2C SLAVE IC Datasheet
Version 1.3
Document No.: FT_000628 Clearance No.: FTDI# 265
These values can have a significant effect on the behaviour of the device. Steps must be taken to ensure
that these locations are not written to un-intentionally by an application which is intended to access only
the user area.
This area is included in a checksum which covers configuration areas of the memory, and so changing
any value can also cause this checksum to fail.
Configuration Memory Area (non-writable)
This is a reserved area and the application should not write to this area of memory. Any attempt to write
these locations will fail.
10.4 Hardware Requirements
The hardware is the same as for a typical USB-I2C application and no additional hardware or
programming voltages are required. The I2C connections are the same as shown in Section 8.1. For the
USB connections, either a bus-powered configuration (see Section 7.1 and 7.3) or a self-powered
configuration (see Section 7.2) could be used.
10.5 Protocol
The I2C MTP memory protocol consists of 3 commands:



Address MTP memory (0x10)
Write MTP memory (0x12)
Read MTP memory (0x14)
2
For further details on the I C protocol, refer to section 5.
10.5.1
Address MTP memory (0x10)
This consists of a general call with a command phase followed by 2 data bytes which represent the MTP
memory address allowing users to address, potentially, up to 64K byte addresses.
10.5.2
Write MTP memory (0x12)
This consists of a general call with a command phase followed by 1 data byte which shall be programmed
into the MTP memory at the address location set by the MTP memory address command.
10.5.3
Read MTP memory (0x14)
This consists of a general call with a command phase followed by 1 data byte which is the data read from
the MTP memory at the address location set by the MTP memory address command.
10.5.4
Examples of Writing and Reading
When performing MTP memory write and read requests via the I2C protocol, users must first issue the
MTP address command along with 2 bytes representing the MTP memory address. The acknowledge
phase of this command represents the current status of the MTP memory (whether it is busy or not). If
the MTP memory is being accessed during an I2C access then the respective command and data phases
will NAK the master. The address will only be updated when the MTP memory is inactive.
Writing
The first part of the communication sets the address, and this is followed by the write command along
with the data to be written. The MTP memory write itself will be initiated when the FT200XD receives an
MTP memory write command followed by a single data byte. The ACK phase represents the current
activity of the MTP memory (whether it is busy or not busy). A successful write will only occur when both
status phases acknowledge the master indicating that the MTP memory can start the write. Users wishing
Copyright © 2013 Future Technology Devices International Limited
34
FT200XD USB I2C SLAVE IC Datasheet
Version 1.3
Document No.: FT_000628 Clearance No.: FTDI# 265
to determine if the MTP memory write was successful should immediately try an MTP memory read to
verify the new contents.
This process of writing to the MTP memory is shown below:
0000000
0
S/Sr General call addr R/!W
0001_0000
A
MTP ADDR cmd
0
A/!A
Sr
Slave addr
R/!W
A
MTP ADR MSB
A
A
MTP WR DATA
A
MTP ADR LSB
A
MTP Memory Address Phase
0000000
0
S/Sr General call addr R/!W
0001_0010
A
MTP WR cmd
0
A/!A
Sr
Slave addr
R/!W
P/Sr
MTP memory Write Phase
Figure 10.2 Write EEPROM command sequence
Reading
In a similar way, the read is carried out as shown below.The first part of the communication sets the
address, and this is followed by the read command and a read cycle used to retrieve the data read back
from that address.
An MTP memory read will be initiated when the I2C slave receives an MTP read command. The
acknowledge during the command phase indicates whether or not the MTP memory will be able to service
the read request. If it is possible to carry out the read, the I2C moves into the data phase where it can
either continue with the read transaction until the slave successful returns an ACK along with the data or
if it receives NAK during the data phase it can abort the read transfer and try again.
0000000
0
S/Sr General call addr R/!W
0001_0000
A
MTP ADDR cmd
0
A/!A
Sr
Slave addr
R/!W
A
MTP ADR MSB
A
A
MTP WR DATA
A
MTP ADR LSB
A
MTP Memory Address Phase
0000000
0
S/Sr General call addr R/!W
0001_0100
A
MTP WR cmd
1
A/!A
Sr
Slave addr
R/!W
P/Sr
MTP memory Read Phase
Figure 10.3 Read EEPROM command sequence
Copyright © 2013 Future Technology Devices International Limited
35
FT200XD USB I2C SLAVE IC Datasheet
Version 1.3
Document No.: FT_000628 Clearance No.: FTDI# 265
11 Package Parameters
The FT200XD is available in a 10 pin DFN package, the FT200XD.The solder reflow profile for the package
is described in Section 0.
11.1 DFN-10 Package Mechanical Dimensions
Figure 11.1 DFN-10 Package Dimensions
The FT200XD is supplied in a RoHS compliant leadless DFN-10package. The package is lead ( Pb ) free,
and uses a ‘green’ compound. The package is fully compliant with European Union directive 2002/95/EC.
This package is nominally 3.00mm x 3.00mm. The solder pads are on a 0.50 mm pitch. The above
mechanical drawing shows the DFN-10 package. All dimensions are in millimetres.
The centre pad on the base of the FT200XD is internally connected to GND. Do not place tracks on the
top layer of the PCB in this area.
Copyright © 2013 Future Technology Devices International Limited
36
FT200XD USB I2C SLAVE IC Datasheet
Version 1.3
Document No.: FT_000628 Clearance No.: FTDI# 265
11.2 Package Markings
10
1
-B
Line 1 – FTDI Logo
Line 2 – Date Code, Revision
Line 3 – Wafer Lot Number
FT200XD
5
Line 4 – FTDI Part Number
6
The date code format is YYXWW where XWW = 2 digit week number, YY = 2 digit year number.
The code XXXXXXX is the manufacturing LOT code.
Copyright © 2013 Future Technology Devices International Limited
37
FT200XD USB I2C SLAVE IC Datasheet
Version 1.3
Document No.: FT_000628 Clearance No.: FTDI# 265
11.3 Solder Reflow Profile
The FT200XD is supplied in Pb free DFN-10 packages. The recommended solder reflow profile for the
package is shown in Figure 11.2.
Temperature, T (Degrees C)
tp
Tp
Critical Zone: when
T is in the range
TL to Tp
Ramp Up
TL
tL
TS Max
Ramp
Down
TS Min
tS
Preheat
25
T = 25º C to TP
Time, t (seconds)
Figure 11.2 FT200XD Solder Reflow Profile
The recommended values for the solder reflow profile are detailed in Table 11.1. Values are shown for
both a completely Pb free solder process (i.e. the FT200XD is used with Pb free solder), and for a non-Pb
free solder process (i.e. the FT200XD is used with non-Pb free solder).
Profile Feature
Pb Free Solder Process
Non-Pb Free Solder Process
Average Ramp Up Rate (Ts to Tp)
3°C / second Max.
3°C / Second Max.
Preheat
- Temperature Min (Ts Min.)
150°C
100°C
- Temperature Max (Ts Max.)
200°C
150°C
- Time (ts Min to ts Max)
60 to 120 seconds
60 to 120 seconds
Time Maintained Above Critical Temperature
TL:
- Temperature (TL)
- Time (tL)
Peak Temperature (Tp)
217°C
60 to 150 seconds
183°C 60 to 150 seconds
260°C
240°C
20 to 40 seconds
20 to 40 seconds
Ramp Down Rate
6°C / second Max.
6°C / second Max.
Time for T= 25°C to Peak Temperature, Tp
8 minutes Max.
6 minutes Max.
Time within 5°C of actual Peak Temperature
(tp)
Table 11.1 Reflow Profile Parameter Values
Copyright © 2013 Future Technology Devices International Limited
38
FT200XD USB I2C SLAVE IC Datasheet
Version 1.3
Document No.: FT_000628 Clearance No.: FTDI# 265
12 Contact Information
Head Office – Glasgow, UK
Branch Office – Hillsboro, Oregon, USA
Future Technology Devices International Limited
Unit 1, 2 Seaward Place, Centurion Business Park
Glasgow G41 1HH
United Kingdom
Tel: +44 (0) 141 429 2777
Fax: +44 (0) 141 429 2758
Future Technology Devices International Limited
(USA)
7130 SW Fir Loop
Tigard, OR 97223
USA
Tel: +1 (503) 547 0988
Fax: +1 (503) 547 0987
E-mail (Sales)
E-mail (Support)
E-mail (General Enquiries)
E-Mail (Sales)
E-Mail (Support)
E-Mail (General Enquiries)
[email protected]
[email protected]
[email protected]
Branch Office – Taipei, Taiwan
Future Technology Devices International Limited
(Taiwan)
2F, No. 516, Sec. 1, NeiHu Road
Taipei 114
Taiwan , R.O.C.
Tel: +886 (0) 2 8791 3570
Fax: +886 (0) 2 8791 3576
E-mail (Sales)
E-mail (Support)
E-mail (General Enquiries)
[email protected]
[email protected]
[email protected]
[email protected]
[email protected]
[email protected]
Branch Office – Shanghai, China
Future Technology Devices International Limited
(China)
Room 408, 317 Xianxia Road,
Shanghai, 200051
China
Tel: +86 21 62351596
Fax: +86 21 62351595
E-mail (Sales)
E-mail (Support)
E-mail (General Enquiries)
[email protected]
[email protected]
[email protected]
Web Site
http://ftdichip.com
System and equipment manufacturers and designers are responsible to ensure that their systems, and any Future Technology
Devices International Ltd (FTDI) devices incorporated in their systems, meet all applicable safety, regulatory and system-level
performance requirements. All application-related information in this document (including application descriptions, suggested
FTDI devices and other materials) is provided for reference only. While FTDI has taken care to assure it is accurate, this
information is subject to customer confirmation, and FTDI disclaims all liability for system designs and for any applications
assistance provided by FTDI. Use of FTDI devices in life support and/or safety applications is entirely at the user’s risk, and the
user agrees to defend, indemnify and hold harmless FTDI from any and all damages, claims, suits or expense resulting from
such use. This document is subject to change without notice. No freedom to use patents or other intellectual property rights is
implied by the publication of this document. Neither the whole nor any part of the information contained in, or the product
described in this document, may be adapted or reproduced in any material or electronic form without the prior written consent
of the copyright holder. Future Technology Devices International Ltd, Unit 1, 2 Seaward Place, Centurion Business Park,
Glasgow G41 1HH, United Kingdom. Scotland Registered Company Number: SC136640
Copyright © 2013 Future Technology Devices International Limited
39
FT200XD USB I2C SLAVE IC Datasheet
Version 1.3
Document No.: FT_000628 Clearance No.: FTDI# 265
Appendix A – References
Useful Application Notes
http://www.ftdichip.com/Documents/AppNotes/AN232R-01_FT232R_BitBangModes.pdf
http://www.ftdichip.com/Documents/AppNotes/AN_107_AdvancedDriverOptions_AN_000073.pdf
http://www.ftdichip.com/Documents/AppNotes/AN_121_FTDI_Device_EEPROM_User_Area_Usage.pdf
http://www.ftdichip.com/Documents/InstallGuides.htm
http://www.ftdichip.com/Support/Documents/TechnicalNotes/TN_100_USB_VID-PID_Guidelines.pdf
http://www.ftdichip.com/Support/Documents/AppNotes/AN_175_Battery%20Charging%20Over%20USB
%20with%20FTEX%20Devices.pdf
http://i2c2p.twibright.com/spec/i2c.pdf
http://www.usb.org/developers/devclass_docs/BCv1.2_011912.zip
Copyright © 2013 Future Technology Devices International Limited
40
FT200XD USB I2C SLAVE IC Datasheet
Version 1.3
Document No.: FT_000628 Clearance No.: FTDI# 265
Appendix B - List of Figures and Tables
List of Figures
Figure 2.1FT200XD Block Diagram .................................................................................................. 4
Figure 3.1 DFN Schematic Symbol .................................................................................................. 7
Figure 7.1 Bus Powered Configuration ........................................................................................... 19
Figure 7.2 Self Powered Configuration ........................................................................................... 20
Figure 7.3 Bus Powered with Power Switching Configuration ............................................................ 21
Figure 8.1 Application Example showing USB to I2C Converter .......................................................... 22
Figure 8.2 USB Battery Charging Detection .................................................................................... 23
Figure 9.2: Data transfers with 7-bit and 10-bit addressing modes ................................................... 28
Figure 9.3: Checking the Data Available Count ............................................................................... 28
Figure 9.4: Flush data command .................................................................................................. 29
Figure 9.5: Reading the amount of data available ........................................................................... 29
Figure 9.6: Checking the USB State .............................................................................................. 30
Figure 9.7: Reading the Device ID ................................................................................................ 30
Figure 10.1 Simplified memory map for the FT-X ............................................................................ 33
Figure 10.2 Write EEPROM command sequence .............................................................................. 35
Figure 10.3 Read EEPROM command sequence ............................................................................... 35
Figure 11.1 DFN-10 Package Dimensions ....................................................................................... 36
Figure 11.2 FT200XD Solder Reflow Profile ..................................................................................... 38
List of Tables
Table 1.1 Ordering part numbers .................................................................................................... 2
Table 3.1 Power and Ground .......................................................................................................... 7
Table 3.2 Common Function pins .................................................................................................... 7
Table 3.3 I2C Interface and CBUS Group (see note 1) ........................................................................ 8
Table 3.4 CBUS Configuration Control ............................................................................................. 9
Table 6.1 Absolute Maximum Ratings ............................................................................................ 13
Table 6.2 ESD and Latch-Up Specifications .................................................................................... 13
Table 6.3 Operating Voltage and Current ....................................................................................... 14
Table 6.4 I/O Pin Characteristics VCCIO = +3.3V (except USB PHY pins) ........................................... 15
Table 6.5 I/O Pin Characteristics VCCIO = +2.5V (except USB PHY pins) ........................................... 16
Table 6.6 I/O Pin Characteristics VCCIO = +1.8V (except USB PHY pins) ........................................... 17
Table 6.7 USB I/O Pin (USBDP, USBDM) Characteristics .................................................................. 18
Table 6.8 MTP Memory Characteristics........................................................................................... 18
Table 6.9 Internal Clock Characteristics ......................................................................................... 18
Table 10.1 Default Internal MTP memory Configuration ................................................................... 32
Table 11.1 Reflow Profile Parameter Values .................................................................................... 38
Copyright © 2013 Future Technology Devices International Limited
41
FT200XD USB I2C SLAVE IC Datasheet
Version 1.3
Document No.: FT_000628 Clearance No.: FTDI# 265
Appendix C - Revision History
Document Title:
USB I2C SLAVE IC FT200XD
Document Reference No.:
FT_000628
Clearance No.:
FTDI# 265
Product Page:
http://www.ftdichip.com/Products/ICs/FTEX.htm
Document Feedback:
Send Feedback
Version 1.0
Initial Release
8th February 2012
Version 1.1
Added USB compliance in section 1.3
17th April 2012
Clarified MTP reliability in table 6.8
Edited Table 9.1: Added I2C address
and changed Load VCP Driver to Disabled
Version 1.2
Added section 9 with details of USB and I2C Interfacing
15th August 2012
Added link to AN_201 (MTP Memory Configuration) in
section 10
Removed references to LED signals on the CBUS pins as
these are only available on the UART members of the FT-X
family.
Removed section 8.3 showing connection of the Tx/Rx LEDs.
Version 1.3
Added 5V tolerant statement on front page
Updated TID info
Updated US address
Feb 2013
Copyright © 2013 Future Technology Devices International Limited
42