VI800A_232U Datasheet Version 1.1 Document Reference No.: FT_000992 Clearance No.: FTDI#411 FTDI Chip VI800A-232U Datasheet Plug in accessory for VM800P Embedded Video Engine Plus module 1 Introduction 1.1 Features The VI800A-232U is a plug in accessory for the VM800P module, which expands the VM800P IO capabilities to include RS232. Connects to the VM800P Plus module using an SPI slave interface This module behaves as an SPI to RS232 bridge on the VM800P Plus module. SPI slave interface is converted to RS232 interface 4 GPIO inputs and 4 GPIO outputs 8 LEDs to indicate the input and output status 5 V tolerant buffers Screw connector to connect the RS232 signals, GPIO inputs and GPIO outputs IO connector to connect the RS232 signals, GPIO inputs and GPIO outputs Powered from the VM800P module Use of FTDI devices in life support and/or safety applications is entirely at the user’s risk, and the user agrees to defend, indemnify and hold FTDI harmless from any and all damages, claims, suits or expense resulting from such use. VI800A_232U Datasheet Version 1.11 Document Reference No.: FT_000992 2 Clearance No.: FTDI#411 Ordering Information Part No. VI800A-232U Description VI800A RS232 module, plug in accessory for the VM800P Plus module Table 2-1 – Ordering information 2 Copyright © 201422/10/2014 Future Technology Devices International Limited VI800A_232U Datasheet Version 1.11 Document Reference No.: FT_000992 Clearance No.: FTDI#411 Table of Contents 1 Introduction ................................................................................... 1 1.1 Features ........................................................................................................ 1 2 Ordering Information ..................................................................... 2 3 Hardware Description ..................................................................... 4 3.1 VI800A-232U module .................................................................................... 4 3.2 Physical Descriptions .................................................................................... 5 3.2.1 PCB Dimensions ........................................................................................ 5 3.2.2 VI800A-232U Connectors ........................................................................... 6 3.2.3 VI800A-232U Components ......................................................................... 8 4 Board Schematics ........................................................................... 9 5 Hardware Setup Guide .................................................................. 10 6 5.1 Power Configuration ................................................................................... 10 5.2 RS232 Interface connection ........................................................................ 10 Contact Information ..................................................................... 11 Appendix A – References....................................................................................... 12 Appendix B - List of Figures and Tables ................................................................. 13 Appendix C – Revision History ............................................................................... 14 3 Copyright © 201422/10/2014 Future Technology Devices International Limited VI800A_232U Datasheet Version 1.11 Document Reference No.: FT_000992 3 Clearance No.: FTDI#411 Hardware Description Please refer to section 3.2.2 for connector settings. Some VI800A-232U jumpers must be set to work properly with your system. 3.1 VI800A-232U module Figure 3-1 – VI800A-232U module The VI800A-232U module is designed to connect directly with the VM800P Plus module. The main functions of the VI800A-232U are as follows: Plug in accessory board for the VM800P Plus module. Interface to the VM800P Plus board as a SPI slave device. Connects with an external RS232 interface. Supports 4 GPIO inputs. Supports 4 GPIO outputs. Contains 8 LEDs, 4 represent input signal level and 4 represent output level. Powered by the VM800P Plus board. 4 Copyright © 201422/10/2014 Future Technology Devices International Limited VI800A_232U Datasheet Version 1.11 Document Reference No.: FT_000992 Clearance No.: FTDI#411 3.2 Physical Descriptions 3.2.1 PCB Dimensions The VI800A-232U module PCB layout is illustrated in Figure 3-2, Figure 3-3 and Figure 3-4. 63.50 37.50 18.75 9.20 Figure 3-2 - VI800A-232U module PCB Top view 4.35 8.50 54.0 Figure 3-3 - VI800A-232U module PCB Bottom view 5 Copyright © 201422/10/2014 Future Technology Devices International Limited VI800A_232U Datasheet Version 1.11 Document Reference No.: FT_000992 Clearance No.: FTDI#411 Figure 3-4 - VI800A-232U module PCB Side view All dimensions are in mm 3.2.2 VI800A-232U Connectors Connectors and jumpers are described in the following sections. CN1- SPI Interface This is the interface where the SPI control and data signals are routed. There are also power and ground pins on this interface. This interface is used to connect the VI800A-232U board to the VM800P Plus board. Note: This connector should be connected to J6 of the VM800P plus board. Pin No. Name Type Description 1 SCLK I SPI Clock input, 3.3V (5V tolerant) 2 MOSI I Master Out Slave in, 3.3V (5V tolerant) 3 MISO O Master In Slave out, 5V 4 SS# I SPI Chip select, active low, 3.3V (5V tolerant) 5 INT0 O Interrupt output active low, 3.3V 6 IO6 I Daughter reset input, active low , 3.3V (5V tolerant) 7 AD4 IO Address/Data Line 4 8 AD5 IO Address/Data Line 5 9 3V3 P 3.3V power supply 10 5V P 5V power supply 11 GND P Ground 12 RST# I Reset, active low 13 AD1 IO Address/Data Line 1 14 NC NA Not Connected 15 AD3 IO Address/Data Line 3 16 AD2 Table 3-1 – CN1 Pinout IO Address/Data Line 2 6 Copyright © 201422/10/2014 Future Technology Devices International Limited VI800A_232U Datasheet Version 1.11 Document Reference No.: FT_000992 Clearance No.: FTDI#411 CN2- IO Interface (alternative to CN3) This is the interface where the RS232 connections, GPIO inputs and outputs are connected. There are also power and ground pins on this interface. Pin No. Name Type 1 3V3 P 3.3V power supply 2 5V P 5V power supply 3 I/P1 I Input 1 4 I/P2 I Input 2 5 I/P3 I Input 3 6 I/P4 I Input 4 7 O/P1 O Output 1 8 O/P2 O Output 2 9 O/P3 O Output 3 10 O/P4 O Output 4 11 GND P Ground 12 GND P Ground 13 TXD_OUT O Transmit Data 14 RXD_IN I Receive Data 15 RTS_OUT O Request to send I Clear to send 16 CTS_IN Table 3-2 – CN2 Pinout Description CN3- External Screw Connector (alternative to CN2) This is the interface where the RS232 connections, GPIO input and outputs are connected. There are also power and ground pins on this interface. Pin No. Name Type Description 1 TXD_OUT O Transmit data 2 RXD_IN I Receive data 3 RTS_OUT O Request to send 4 CTS_IN I Clear to send 5 GND P Ground 6 I/P1 I Input 1 7 I/P2 I Input 2 8 I/P3 I Input 3 9 I/P4 I Input 4 10 O/P1 O Output 1 11 O/P2 O Output 2 12 O/P3 O Output 3 7 Copyright © 201422/10/2014 Future Technology Devices International Limited VI800A_232U Datasheet Version 1.11 Document Reference No.: FT_000992 Pin No. Name Type 13 O/P4 O Output 4 14 GND Table 3-3 – CN3 Pinout P Ground Clearance No.: FTDI#411 Description JP1- Output Drive Select This jumper provides the option to select the power supply voltage for the inputs and outputs. Jumper position Description Short pin 1-2 3.3V selected Short pin 2-3 Table 3-4 – JP1 Pin options 5V selected (default) 3.2.3 VI800A-232U Components U1 – SC16IS760 This converts the SPI signals from the VM800P Plus board to UART TTL signals. U4 – ZT3222F This converts the UART signals from the TTL level to RS232 level. LED1 – LED4 Indicates the status of GPIO inputs. Illuminate when the GPIO line is logic 0. LED5 –LED8 Indicates the status of the GPIO outputs. Illuminate when the GPIO line is logic 0. 8 Copyright © 201422/10/2014 Future Technology Devices International Limited VI800A_232U Datasheet Version 1.11 Document Reference No.: FT_000992 4 Clearance No.: FTDI#411 Board Schematics Figure 4-1 - VI800A-232U Schematics 9 Copyright © 201422/10/2014 Future Technology Devices International Limited VI800A_232U Datasheet Version 1.11 Document Reference No.: FT_000992 5 Clearance No.: FTDI#411 Hardware Setup Guide 5.1 Power Configuration The board is powered from the VM800P Plus board. The CN1 connector on the VI800A-232U board should be connected to the J6 connector of the VM800P plus board as shown in the Figure 5-1. Figure 5-1 - VI800A-232U module connected to VM800P Plus module 5.2 RS232 Interface connection The TXD_OUT signal on CN3 is connected to the RXD signal on the external RS232 device. The RXD_IN signal on CN3 is connected to the TXD signal on the external RS232 device. The RTS_OUT signal on CN3 is connected to the CTS signal on the external RS232 device. The CTS_IN signal on CN3 is connected to the RTS signal on the external RS232 device. The GND signal on CN3 is connected to the GND signal on the external RS232 device. The output from the external device is connected to the inputs I/P1, I/P2, I/P3 and I/P4 on CN3. The outputs O/P1, O/P2, O/P3 and O/P4 on CN3 are connected to the input of the external device. The LEDs LED1 to LED8 are used to display the status of the inputs and outputs. This interface is used to interface the VM800P Plus module to the devices having RS232 and GPIO interfaces. 10 Copyright © 201422/10/2014 Future Technology Devices International Limited VI800A_232U Datasheet Version 1.11 Document Reference No.: FT_000992 6 Clearance No.: FTDI#411 Contact Information Head Office – Glasgow, UK Branch Office – Tigard, Oregon, USA Unit 1, 2 Seaward Place, Centurion Business Park Glasgow G41 1HH United Kingdom Tel: +44 (0) 141 429 2777 Fax: +44 (0) 141 429 2758 7130 SW Fir Loop Tigard, OR 97223 USA Tel: +1 (503) 547 0988 Fax: +1 (503) 547 0987 E-mail (Sales) E-mail (Support) E-mail (General Enquiries) E-Mail (Sales) E-Mail (Support) E-Mail (General Enquiries) [email protected] [email protected] [email protected] [email protected] [email protected] [email protected] Branch Office – Taipei, Taiwan Branch Office – Shanghai, China 2F, No. 516, Sec. 1, NeiHu Road Taipei 114 Taiwan , R.O.C. Tel: +886 (0) 2 8797 1330 Fax: +886 (0) 2 8751 9737 Room 1103, No. 666 West Huaihai Road, Changning District, Shanghai, 200052 China Tel: +86 (0)21 6235 1596 Fax: +86 (0)21 6235 1595 E-mail (Sales) E-mail (Support) E-mail (General Enquiries) E-mail (Sales) E-mail (Support) E-mail (General Enquiries) [email protected] [email protected] [email protected] [email protected] [email protected] [email protected] Web Site http://www.ftdichip.com/ Distributor and Sales Representatives Please visit the Sales Network page of the FTDI Web site for the contact details of our distributor(s) and sales representative(s) in your country. System and equipment manufacturers and designers are responsible to ensure that their systems, and any Future Technology Devices International Ltd (FTDI) devices incorporated in their systems, meet all applicable safety, regulatory and system-level performance requirements. All application-related information in this document (including application descriptions, suggested FTDI devices and other materials) is provided for reference only. While FTDI has taken care to assure it is accurate, this information is subject to customer confirmation, and FTDI disclaims all liability for system designs and for any applications assistance provided by FTDI. Use of FTDI devices in life support and/or safety applications is entirely at the user’s risk, and the user agrees to defend, indemnify and hold harmless FTDI from any and all damages, claims, suits or expense resulting from such use. This document is subject to change without notice. No freedom to use patents or other intellectual property rights is implied by the publication of this document. Neither the whole nor any part of the information contained in, or the product described in this document, may be adapted or reproduced in any material or electronic form without the prior written consent of the copyright holder. Future Technology Devices International Ltd, Unit 1, 2 Seaward Place, Centurion Business Park, Glasgow G41 1HH, United Kingdom. Scotland Registered Company Number: SC136640 11 Copyright © 201422/10/2014 Future Technology Devices International Limited VI800A_232U Datasheet Version 1.11 Document Reference No.: FT_000992 Clearance No.: FTDI#411 Appendix A – References VM800P Datasheet: VM800P Plus board FT800 datasheet: FT800_Embedded_Video_Engine FT800 software programming guide: FT800_Programmer_Guide FT800 sample application notes: AN_246_VM800CB_SampleAPP_Arduino_Introduction AN_275_FT800_Example_with_Arduino AN_318 Arduino Library for FT800 Series AN_330 VI800A_TTL_232U_N485U_ArduinoLibrary_Sample 12 Copyright © 201422/10/2014 Future Technology Devices International Limited VI800A_232U Datasheet Version 1.11 Document Reference No.: FT_000992 Clearance No.: FTDI#411 Appendix B - List of Figures and Tables List of Figures Figure 3-1 – VI800A-232U module .................................................................................................................. 4 Figure 3-2 - VI800A-232U module PCB Top view ......................................................................................... 5 Figure 3-3 - VI800A-232U module PCB Bottom view ................................................................................... 5 Figure 3-4 - VI800A-232U module PCB Side view ........................................................................................ 6 Figure 4-1 - VI800A-232U Schematics ........................................................................................................... 9 Figure 5-1 - VI800A-232U module connected to VM800P Plus module .................................................... 10 List of Tables Table 2-1 – Ordering information ................................................................................................................... 2 Table 3-1 – CN1 Pinout .................................................................................................................................... 6 Table 3-2 – CN2 Pinout .................................................................................................................................... 7 Table 3-3 – CN3 Pinout .................................................................................................................................... 7 Table 3-4 – JP1 Pin options ............................................................................................................................ 8 13 Copyright © 201422/10/2014 Future Technology Devices International Limited VI800A_232U Datasheet Version 1.11 Document Reference No.: FT_000992 Clearance No.: FTDI#411 Appendix C – Revision History Document Title: DS_VI800A-232U Document Reference No.: FT_000992 Clearance No.: FTDI#411 Product Page: http://www.ftdichip.com/EVE.htm Document Feedback: Send Feedback Version 1.0 Initial Datasheet released 14/10/14 Version 1.1 Added height dimensions 20/10/14 14 Copyright © 201422/10/2014 Future Technology Devices International Limited