CONDUCTIVE POLYMER ALUMINUM SOLID CAPACITORS Surface Mount New! @Super low ESR, impedance and high heat resistance have been obtained by using conductive polymer as electrolyte. @Rated voltage range : 2.5 to 16Vdc, Capacitance range : 100 to 560MF @Suitable for DC-DC converters, voltage regulators and decoupling applications used to computer motherboards etc. @RoHS Compliant PXK Downsized PXE ?SPECIFICATIONS Items Characteristics Category Temperature Range Rated Voltage Range Capacitance Tolerance Surge Voltage Leakage Current Dissipation Factor (tane) Low Temperature Characteristics (Max. Impedance Ratio) -55 to +105C 2.5 to 16Vdc P20% (M) Rated voltageB1.15V Shall not exceed values shown in STANDARD RATINGS. (at 20C, 120Hz) (at 105C) (at 20C after 2 minutes) 0.12 max. (at 20C, 120Hz) Z(-25C)/Z(+20C)[1.15 Z(-55C)/Z(+20C)[1.25 (at 100kHz) The following specifications shall be satisfied when the capacitors are restored to 20C after the rated voltage is applied for 2,000 hours (F46 : 1,000 hours) at 105C. Appearance No significant damage Capacitance change [P20% of the initial value DF (tanE) [150% of the initial specified value ESR [150% of the initial specified value Leakage current [The initial specified value The following specifications shall be satisfied when the capacitors are restored to 20C after subjecting them to the DC rated voltage at 60C, 90 to 95% RH for 1,000 hours (F46 : 500hours). Appearance No significant damage Capacitance change [P20% of the initial value DF (tanE) [150% of the initial specified value ESR [150% of the initial specified value Leakage current [The initial specified value The capacitors shall be subjected to 1,000 cycles each consisting of charge with the surge voltage specified at 105C for 30 seconds through a protective resistor(R=1kO) and discharge for 5 minutes 30 seconds. Appearance No significant damage Capacitance change [P20% of the initial value DF (tanE) [150% of the initial specified value ESR [150% of the initial specified value Leakage current [The initial specified value 0.5% per 1,000 hours maximum (Confidence level 60% at 105C) Endurance Bias Humidity Surge Voltage Failure Rate *Note : If any doubt arises, measure the leakage current after following voltage treatment. Voltage treatment : DC rated voltage are applied to the capacitors for 120 minutes at 105C. ?DIMENSIONS [mm] ?MARKING @Terminal Code : A EX) 2.5V330MF P CP0.2 BP0.2 FDP0.5 W 0.3max. LP0.3 (Note) Size Code E61 F46 F61 fD 5 6.3 6.3 L 5.8 4.5 5.8 A 5.3 6.6 6.6 B 5.3 6.6 6.6 C 5.9 7.2 7.2 W 0.5 to 0.8 0.5 to 0.8 0.5 to 0.8 P 1.4 1.9 1.9 K89A 330 2.5V AP0.2 Note : L+0.1/-0.2 for F46 ?PART NUMBERING SYSTEM 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 A PXK AAA A RA AAA M AAA G Supplement code Size code Capacitance tolerance code Capacitance code (ex. 330MF:331, 560MF:561) Taping code Terminal code Voltage code (ex. 2.5V:2R5, 6.3V:6R3) Series code Category Please refer to "Product code guide (conductive polymer type)" (1/2) CAT. No. E1001K CONDUCTIVE POLYMER ALUMINUM SOLID CAPACITORS Surface Mount New! ?STANDARD RATINGS WV (Vdc) 2.5 4 6.3 16 Cap (mF) Size code 220 330 330 560 180 220 390 150 180 220 330 100 F46 E61 F46 F61 F46 E61 F61 F46 E61 F46 F61 F61 Leakage current ESR (mAmax/after 2min.) (momax/20c, 100k to 300kHz) 300 412 700 700 360 440 780 472 567 700 1,040 320 19 16 16 16 19 17 17 19 17 18 17 24 (2/2) Rated ripple current (mArms/105c, 100kHz) 2,780 3,500 3,500 3,500 2,780 3,390 3,390 2,780 3,390 3,200 3,390 2,490 Part No. APXK2R5ARA221MF46G APXK2R5ARA331ME61G APXK2R5ARA331MF46G APXK2R5ARA561MF61G APXK4R0ARA181MF46G APXK4R0ARA221ME61G APXK4R0ARA391MF61G APXK6R3ARA151MF46G APXK6R3ARA181ME61G APXK6R3ARA221MF46G APXK6R3ARA331MF61G APXK160ARA101MF61G CAT. No. E1001K