CONDUCTIVE POLYMER ALUMINUM SOLID CAPACITORS Radial Lead New! ●Super low ESR, high ripple current capability 2,000 to 5,000 hours at 105℃ ●Rated voltage : 16 to 20Vdc ●RoHS Compliant ●Halogen Free ●Endurance: PSG Downsized PSF ◆SPECIFICATIONS Items Category Temperature Range Rated Voltage Capacitance Tolerance Surge Voltage Leakage Current Characteristics -55 to +105℃ *Note 16 to 20Vdc P20% (M) Rated voltage(V)B1.15 I=0.2CV or 500μA, whichever is greater Where, I : Leakage current (μA), C : Nominal capacitance (μF), V : Rated voltage (V) Dissipation Factor (tanδ) 0.12 max. Low Temperature Characteristics (Max.Impedance Ratio) Z(-25℃)/Z(+20℃)≦1.15 Z(-55℃)/Z(+20℃)≦1.25 Endurance Bias Humidity Test Surge Voltage Test Failure Rate (at 20℃, 120Hz) (at 105℃) (at 20℃ after 2 minutes) (at 20℃, 120Hz) (at 100kHz) The following specifications shall be satisfied when the capacitors are restored to 20℃ after the rated voltage is applied for 5,000 hours (20V : 2,000 hours) at 105℃. Appearance No significant damage Capacitance change ≦±20% of the initial value D.F. (tanδ) ≦The initial specified value ESR ≦150% of the initial specified value Leakage current ≦The initial specified value The following specifications shall be satisfied when the capacitors are restored to 20℃ after subjecting them to DC voltage at 60℃, 90 to 95% RH for 1,000 hours. Appearance No significant damage Capacitance change ≦±20% of the initial value D.F. (tanδ) ≦The initial specified value ESR ≦150% of the initial specified value Leakage current ≦The initial specified value The capacitors shall be subjected to 1,000 cycles each consisting of charge with the surge voltage specified at 105℃ for 30 seconds through a protective resistor(R=1kΩ) and discharge for 5 minutes 30 seconds. Appearance No significant damage ≦±20% of the initial value Capacitance change ≦The initial specified value D.F. (tanδ) ≦150% of the initial specified value ESR ≦The initial specified value Leakage current 0.5% per 1,000 hours maximum (Confidence level 60% at 105℃) *Note : If any doubt arises, measure the leakage current after the following voltage treatment. Voltage treatment : DC rated voltage is applied to the capacitors for 120 minutes at 105℃. Product specifications in this catalog are subject to change without notice.Request our product specifications before purchase and/or use. Please use our products based on the information contained in this catalog and product specifications. (1/2) CAT. No. E1001L CONDUCTIVE POLYMER ALUMINUM SOLID CAPACITORS Radial Lead New! ◆DIMENSIONS [mm] ●Terminal Code : E F05,F08,H06,H08 F±0.5 Size code F05 F08 H06 H08 φD 6.3 8.0 φd 0.45 0.6 F 2.5 3.5 φD' D+0.5max. L' L+1.0max. φD' φd Coated Case L' 15min. HB5 JB5 10.0 5.0 L+1.5max. ◆MARKING EX) 16V150F G 6D6 150 16V 4min. F±0.5 HB5,JB5 φD' φd Coated Case L' 15min. 4min. ◆PART NUMBERING SYSTEM 1 2 3 4 A PSG 5 6 7 8 9 10 11 12 E 13 14 15 16 17 M 18 S Supplement code Size code Capacitance tolerance code Capacitance code (ex. 150µF:151) Lead forming·Taping code Terminal code Voltage code (ex. 16V:160,20V:200) Series code Category Please refer to “Product code guide (conductive polymer type)” ◆STANDARD RATINGS WV(Vdc) 16 20 Cap(µF) 150 270 270 470 560 820 1,000 120 φD×L (mm) Case size ESR (mΩ max. /20℃, 100 k to 3 00kHz) Rated ripple current (mArms/105℃, 100kHz) Part No. 6.3×5 6.3×8 8×6 8×8 8×11.5 10×11.5 10×11.5 6.3×5 20 15 22 16 14 12 12 20 3,200 3,800 3,300 4,000 4,970 5,400 5,400 3,200 APSG160E□□151MF05S APSG160E□□271MF08S APSG160E□□271MH06S APSG160E□□471MH08S APSG160E□□561MHB5S APSG160E□□821MJB5S APSG160E□□102MJB5S APSG200E□□121MF05S □□ : Enter the appropriate lead forming or taping code. Product specifications in this catalog are subject to change without notice.Request our product specifications before purchase and/or use. Please use our products based on the information contained in this catalog and product specifications. (2/2) CAT. No. E1001L