AZ Displays, Inc.

AZ DISPLAYS
SPECIFICATIONS FOR
LIQUID CRYSTAL DISPLAY
CUSTOMER APPROVAL
※ PART NO. : ATM0280D11 (AZ DISPLAYS) VER1.0
APPROVAL
COMPANY
CHOP
CUSTOMER
COMMENTS
AZ DISPLAYS ENGINEERING APPROVAL
DESIGNED BY
YGB
CHECKED BY
APPROVED BY
ATM0280D11(AZ DISPLAYS) TFT MODULE VER1.0
REVISION RECORD
REVISION
VER1.0
REVISION DATE
2012-12-10
AZ DISPLAYS
PAGE
CONTENTS
FIRST ISSUED
1
ATM0280D11(AZ DISPLAYS) TFT MODULE VER1.0
※ CONTENTS
1. GENERAL SPECIFICATION
2. ELECTRICAL CHARACTERISTICS
3. OPTICAL CHARACTERISTICS
4. RELIABILITY TEST
5. PRECAUTION FOR USE OF LCD MODULE
6. DRAWING
AZ DISPLAYS
2
ATM0280D11(AZ DISPLAYS) TFT MODULE VER1.0
1.1 Caution
1. This Zettler LCD module has been specifically designed for use only in Electronic devices in the areas of
mobile phone. The module should not be used in applications where panel failure could result in physical harm or
loss of life, and Zettler expressly disclaims any and all liability relating in any way to the use of the module in such
applications.
2. Customer agrees to indemnity, defend and hold Zettler harmless from and against any and all actions,
claims, losses, damages, liabilities, awards, costs, and expenses, including legal fees, resulting from or arising out
of Customer's use, or sale for use, of Zettler module in applications.
1.2 Description
ATM0280D11 is a transmissive type color active matrix TFT liquid crystal display that use amorphous silicon
TFT as switching devices. This module is composed of a TFT-LCD module , a driver circuit and back-light unit. The
resolution of 2.8” contains 320*240 pixels and can display up to 65K/262K colors.
1.3 Block diagram
CS
SDI
r0-r4,g0-g5,b0-b4
Y1
Source
Driver
Gate
Driver
RS
HSYNC
VSYNC
PCLK
DE
GND
VCC(2.8v)
G320
Y720
2.8"
TFT LCD Panel
Gate
Driver
Timing Controller
with Memory
DC/DC
Converter
Connection with host
SCL
RESET
ILI9341
G1
AZ DISPLAYS
3
ATM0280D11(AZ DISPLAYS) TFT MODULE VER1.0
1.4 General Specifications
ITEM
Specification
LCD Mode
TFT; RGB Color; Normal White; Transmissive
Controllable Color
Indication data: Red-5/6bit, Green-6bit,
Blue-5/6bit gradation control
65K/262K Colors
Background Color
Indication data: Red (1,1,1,1,1,(1)) /
Green(1,1,1,1,1,1) / Blue (1,1,1,1,1,(1))
White
Viewing direction
12 O'Clock
Backlight
LED white colored Backlight (LED unit, 4 chip LED)
Driver IC
ILI9341(ILITEK)
Mounting methods
COG
Operating temperature
-20℃~70℃
Storage temperature
-30℃~80℃
Operating humidity
Temp.≦40℃,85%RH MAX.
Temp.>40℃,Absolute humidity shall be less than 85%RH at 40℃
Temp.≦40℃,85%RH MAX.
Temp.>40℃,Absolute humidity shall be less than 85%RH at 40℃
Storage humidity
(Note) Color tone is slightly changed by temperature and driving voltage.
This product measure up Rohs standard.
1.5 Mechanical Specifications
ITEM
Specification
Outline Dimension
According to the annexed outline drawing
Dots Matrix
(240×3) (W) × 320(H) Dots
Glass Area(mm)
46.5*65.6
Active Area (mm)
43.2*57.6
Mass
TBD
AZ DISPLAYS
4
ATM0280D11(AZ DISPLAYS) TFT MODULE VER1.0
1.6 Terminal Functions
NO
Symbol
Function
I/O
1
LED+
LED anode pin(V=12.8v,I=18ma)
I
2
3
LEDPCLK
LED cathode pin
Dot clock signal for RGB interface operation.
I
I
4
HSYNC
Line synchronizing signal for RGB interface operation.
I
5
VSYNC
6
SCL
7
8
9
SDI
DE
GND
10
RS
11
RESET
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
CS
B0
B1
B2
B3
B4
G0
G1
G2
G3
G4
G5
R0
R1
R2
R3
R4
NC
NC
NC
NC
Chip select input pin (“Low” enable).
Blue data bus
Blue data bus
Blue data bus
Blue data bus
Blue data bus
Green data bus
Green data bus
Green data bus
Green data bus
Green data bus
Green data bus
Red data bus
Red data bus
Red data bus
Red data bus
Red data bus
-----
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
I
-
33
VCC(2.8V)
Power supply(2.8V)
P
34-40
GND
Ground
-
AZ DISPLAYS
Frame synchronizing signal for RGB interface operation.
This pin is used serial interface clock in 4-wire 8-bit
serial data interface.
The data is applied on the rising edge of the SCL signal.
Data enable signal for RGB interface operation.
Ground
I
I
I
-
Serves as command or parameter select.
I
This signal will reset the device and must be applied to properly
initialize the chip.Signal is active low.
I
I
5
ATM0280D11(AZ DISPLAYS) TFT MODULE VER1.0
2.1 Absolute maximum ratings
Item
Symbol
Value
Unit
Operation Temperature
Top
-20~70
℃
Storage Temperature
Tstr
-30~80
℃
Power supply voltage
VDD
-0.3~3.0
V
2.2 LED back light specification (per a Chip)
Item
Symbol
Condition
Min
Type
Max
Unit
Forward voltage
Vf
If=15mA
-
3.2
-
V
Forward current
Ipn
/1-chip
-
15
-
mA
Reverse voltage
Vr
per chip
-
-
4.0
V
Reverse Current
Ir
Vr=4V
-
-
15
uA
Uniformity (with L/G)
-
If=20mA
70
-
-
%
Lv
If=20mA
-
220
-
cd/m2
Module brightness
Luminous color
White
2.3 Time Sequence
2.3.1 Write Cycle and Sequence
AZ DISPLAYS
6
ATM0280D11(AZ DISPLAYS) TFT MODULE VER1.0
2.3.2 Reset timing
2.3.3 DPI Interface Timing Characteristics
AZ DISPLAYS
7
ATM0280D11(AZ DISPLAYS) TFT MODULE VER1.0
2.4 Electrical characteristics
Item
Symbol
Condition
Min
Type
Max
Unit
Input high voltage
Vih
0.8 VDD
-
VDD
V
Input low voltage
Vil
-0.3
-
0.2 VDD
V
Output high voltage
Voh
Ioh=-0.1mA
0.8 VDD
-
-
V
Output low voltage
Vol
Iol=0.1mA
-
-
0.2 VDD
V
Input leakage current
Iil
Vin=0--Vdd
-1.0
-
1.0
uA
Current consumption
Idd
-
-
-
20.0
mA
2.5 Touch Panel Specification
Item
Descripton
2.5.1 Rating
The maximum voltage
Operating temperature
range
DC5V Max
-20℃~60℃:
-20℃~40℃ 90%RH or less
40℃~60℃ 60%RH or less
-40℃~70℃:
Storage temperature
range
-40℃~40℃ 90%RH or less
40℃~60℃ 60%RH or less
60℃~70℃ 50%RH or less and 168 hours or less
Avoid storage in high temperature and high humidity. When long-term storage
is required. Keep the panels at a temperature of 15℃ to 35℃ and a relative
humidity of 60%RH or less.
2.5.2 Electrical
Resistance between
leads
Direction ”X” (Film side): 200~900Ω
Direction ”Y” (Glass side): 200~900Ω
Linearity
±1.5%, Measured per appendix A
Insulation resistance
20MΩ or more, Apply DC 25V between upper and lower electrodes.
Chattering time
10 msec or less
2.5.3 Mechanical
AZ DISPLAYS
8
ATM0280D11(AZ DISPLAYS) TFT MODULE VER1.0
Input with pen 10~80g (Use R0.8, Polyacetal stylus) see Figure 1
Input with finger 20g Min. (Use R8, HS40°Silicon Rubber) see Figure 2
Activation force
Surface hardness
FPC peeling strength
3 H min. (Pencil test per JISK5600)
300g/cm at speed 100mm/min upward 90°
Min.5kg at speed 20 mm/min,
Static load test
2.5.4 Optical
Light
Transparency
80%Min., Total light Transparency according to JISK7105
2.5.5 Durability
Knocking life
Pen
sliding resistance
AZ DISPLAYS
1,000,000 time, The test shall be done at the load of 250g, 5Hz with 0.8R polyacetal
stylus. After test, there is no pitting allowed on the product.
100,000 cycles, The test shall be done at least 5mm from A/A edge, Using R0.8
polyacetal stylus on the load of 250g and with a stylus change after every 10,000
cycles, one cycle is a 35mm straight line in one direction @60 mm/sec. No visible
scratches when viewed with the naked eye, using office lighting conditions, at a
distance of 6 inches and at viewing angles of 90 and 45 degrees with the backlight off.
9
ATM0280D11(AZ DISPLAYS) TFT MODULE VER1.0
3.1 Optical Characteristics
Item
Symbol
Temp
Min
Type
Max
Unit
Tr
25℃
-
-
TBD
ms
-
-
TBD
ms
45
-
Response time*1
Viewing Angle*1
Threshold voltage*1
Td
Hor.
25℃
-
Ver.
25℃
20
Vsat
Vth
Contrast Ratio
25℃
Cr
W
R
Color of CIE
Coordinate
G
B
NTSC Ratio
25℃
45
-
-
-
-
-
-
-
300
-
x
0.297
y
0.327
x
0.631
y
0.316
x
0.298
y
0.566
x
0.138
y
0.122
S
59
Deg.
V
-
Condition
Φ=0°θ=0°
θ=0°
θ=90°
CR>2
Φ=0°
θ=0°
Φ=0°
θ=0°
Φ=0°
θ=0°
%
(Note*1)The data above is only for panel.
3.2 Definition of Optical Characteristics
3.2.1 Definition of Threshold voltage and Saturation voltage
AZ DISPLAYS
10
ATM0280D11(AZ DISPLAYS) TFT MODULE VER1.0
3.2.2 Definition of Viewing Angle
φ
θ
3.2.3 Definition of Response Time
AZ DISPLAYS
11
ATM0280D11(AZ DISPLAYS) TFT MODULE VER1.0
3.2.4 Definition of Contrast Ratio
Brightness of all pixel white
Contrast Ratio =
Brightness of all pixel black
3.2.5 Definition of Color gamut
θ
θ
AZ DISPLAYS
12
ATM0280D11(AZ DISPLAYS) TFT MODULE VER1.0
4.1 Content of Reliability Test
NO.
TEST ITEMS
TEST CONDITION
1
High Temperature Storage Test
TA=80℃, 48hrs/96hrs
2
Low Temperature Storage Test
TA=-30℃, 48hrs/96hrs
3
High Temperature and High Humidity
Operation Test
TA=40℃, 90RH%, 48hrs/96hrs
(No Condensation Dew)
4
High Temperature Operation Test
TA=70℃, 48hrs/96hrs
5
Low Temperature Operation Test
TA=-20℃, 48hrs/96hrs
6
Heat Shock Test
TA=-30℃(0.5hrs)~80℃(0.5hrs)/10Cycle
* A test LCD panel is used in all the tests./Each test item uses a test LCD panel only once. The tested LCD panel is
not used in any other tests.
* The LCD panel is tested in circumstances in which there is no condensation.
* The tested LCD is inspected after 2 hours of storage at room temperature and room humidity after each test is
finished.
AZ DISPLAYS
13
ATM0280D11(AZ DISPLAYS) TFT MODULE VER1.0
5.1 Handling Precautions of panel
*As LCD module is glass product of precision processing and special treatment, it is vulnerable enough to have
chips and cracks easily. And especially edges should be protected from shocks. If the liquid crystals in LCD flows
out when the product is broken pay most attention to that you do not put the liquid crystal into your eyes and mouth.
If the liquid crystal touches your hand, skin, or clothing, wash it away with soap and water immediately and
completely.
*The polarizer on LCD is soft and easily scratched. If the surface is stained, use soft dry cloth and wipe gently. If
the surface is heavily stained, use the following solvents: 1, Isopropyl alcohol. 2, Ethyl alcohol. Other solvents may
damage the polarizer. Especially, do not use water, ketone and aromatic solvents.
*Do not give any pressure to the surface of LCD, and do not give excessive stresses to the side of LCD module.
It may cause a distortion of color on the LCD.
*As LCD module uses CMOS devices, it is very sensitive to static electricity.
*Touching the IC of LCD module may cause abnormal display that cannot recover. Do not touch the IC of LCD
module.
*If the logic circuit power is OFF, do not apply the input signals.
*Be sure to ground the body when handling the LCD module.
*Tools required for assembly, such as soldering irons, must be properly grounded.
*To prevent destruction of the elements by static electricity be careful to maintain an optimum work environment.
*Do not forcibly pull or bend the I/O cable.
*Do not disassemble or process the LCD module.
*NC terminal should be open. Do not connect anything.
*To reduce the amount of static electricity generated, do not conduct assembly and other work under dry
conditions.
*The LCD module is coated with a film to protect the display surface. Take care when peeling off this protective
film since static electricity may be charged.
*Please handle carefully, because the glass has a sharp edge.
5.2 Storage Precautions
*Take care to minimize corrosion of the electrode. Moisture condensation on a current flow in a high humidity
environment accelerates corrosion of the electrode.
*When storing the LCD module, avoid exposure to direct sunlight or to the light of fluorescent lamps. Keep the
LCD module in bags designed to prevent static electricity charging under low temperature/normal humidity
conditions (avoid high temperature/ high humidity and low temperature below 0℃).
5.3 Design Precautions
*The absolute maximum ratings represent the rated value beyond which LCD module can not exceed. When the
LCD module is used in excess of this fated value, their operating characteristics may be adversely affected. To
prevent the occurrence of erroneous operation caused by the noise, attention must be paid to satisfy VIL, VIH
specification values, including taking the precaution of using signal cables that are short.
*The liquid crystal display exhibits temperature dependency characteristics. Since recognition of the display
becomes difficult when the LCD is used out of its designated operating temperature range, be sure to use the LCD
within this range.
* We recommend that power supply lines (VDD, VEE) have over-current protection line. (Fuse etc.)
*Sufficiently notice the mutual noise interference occurred by peripheral devices.
*To cope with EMI, take measure basically on outputting side.
*When fixing LCD module, which is consisted of glass panel, TCP fixes it at plastic case side. In case PCB is
fixed, there is the possibility that the disconnection is occurred by somewhat stress.
*When mounting the LCD module, make sure that it is free of twisting, warping and distortion. Distortion has
great influence upon display quality. Also keep the shiftiness enough regarding the outer case.
AZ DISPLAYS
14
ATM0280D11(AZ DISPLAYS) TFT MODULE VER1.0
5.4 Other
*Liquid crystal solidify under low temperatures (below the storage temperature range) leading to defective
orientation or the generation of air bubbles. Air bubbles may also be generated if the LCD module is subjected to a
strong shock at a low temperature.
*If the LCD module has been operating for a long time showing the same display patterns, the display patterns
may remain on the screen as ghost images and a slight contract irregularity may also appear. A normal operating
status can be regained by suspending use for some time it should be noted that this phenomenon does not
adversely affect performance reliability.
*To minimize the performance degradation of the LCD modules resulting from destruction caused sections by
static electricity, etc, take care to avoid touching the following sections when handing the module.
①Terminal electrode sections, ②Part of pattern wiring on FPC, etc.
AZ DISPLAYS
15
3.4
AZ DISPLAYS
(25)
43.2(LCD A/A)
*50±0.2(OUTLINE)
0.15
(31.5)
2.7
40
0.3± 0.05
4.5±0.3
20.5± 0.1
21± 0.5
PI Stiffener
*2.8±0.15
With FPC&B/L FPC
ALL-0.8
*2.65(MAX)
2-R
0.2
40
1
4±0.3
Single layer
*3
-?
0.
95
±
0.
*0±0.1
BLU CIRCUIT DIAGRAM
Insulation tape&
Solder High T:0.35mm
*49.05±0.1
1
*0.475 ± 0.1
Single layer
20±0.5
1
Single layer
PLCK
HSYNC
3
4
0.5± 0.1
VCC(2.8V)
GND
GND
GND
GND
GND
GND
GND
34
35
36
37
38
39
40
NC
33
NC
R4
32
R3
28
NC
R2
27
31
R1
26
NC
R0
25
30
G5
24
29
G4
23
G1
22
G0
19
G2
B4
18
G3
B3
17
21
B2
16
20
B1
15
11
14
RESET
10
CS
RS
9
B0
GND
8
13
DE
7
12
SCL
SDI
6
VSYNC
LED-
2
5
LED+
1
NO. PIN NAME
ATM0280D11(AZ DISPLAYS) TFT MODULE VER1.0
6.1 Module outline
*68.25 ± 0.1
(48.2)
20.5± 0.1
Pitch 0.5*(40-1)=19.5 ± 0.1/W=0.3mm
*69.2 ± 0.2(OUTLINE)
57.6(LCD A/A)
16