AZ DISPLAYS SPECIFICATIONS FOR LIQUID CRYSTAL DISPLAY CUSTOMER APPROVAL ※ PART NO. : ATM0700L26B-T(AZ DISPLAYS) VER1.0 COMPANY CHOP APPROVAL CUSTOMER COMMENTS AZ DISPLAYS ENGINEERING APPROVAL DESIGNED Herbert BY CHECKED BY LH APPROVED GZH BY ATM0700L26B-T(AZ DISPLAYS) TFT MODULE V1.0 Document Revision History Revision Data Page V1.0 2015/07/22 -- AZ DISPLAYS Description First issue Changed BY -- 1 ATM0700L26B-T(AZ DISPLAYS) TFT MODULE V1.0 Contents 1. LCM Specification……………………………………………..….3 2. PIN ASSIGNMENT……………………………………………..…4 3. Mechanical Specification…………………………………….……7 4. Electrical Units……………………………………………….……8 5. Timing Characteristics…………………………………...…….….10 6. Optical Specifications……………………………………….…….12 7. Reliability Test Items………………………………………….…..15 8. Handling Precautions…………………………………………..….15 9.Inspection Criterion …………………………………………..… 16 AZ DISPLAYS 2 ATM0700L26B-T(AZ DISPLAYS) TFT MODULE V1.0 1. LCM Specification 1.1 Description ATM0700L26B-T is a transmissive type color active matrix liquid crystal display (LCD) which uses amorphous thin film transistor (TFT) as switching devices. This product is composed of a TFT LCD panel, a drive IC, a FPC, and a WLED-backlight unit.The active display area is 7.0 inches diagonally measured and the native resolution is 1024*RGB*600. Features of this product are listed in the following table. 1.2 Functions & Features Table1.1 Module Functions & Features Parameter LCD Mode Color Display Resolution Outline Dimension Active Area(A.A) Pixel Arrangement Viewing Direction Display Mode IC Package Type Surface Treatment Back-light Operation Temperature Storage Temperature Value a-Si TFT/transmissive 16.7M 1024*3(RGB)*600 160.6(W) *99.4(H) *4.5(T) 153.6*(W) *90(H) RGB-stripe U/D/L/R free viewing direction Normally Black COG Anti-Glare,Hardness:3H White LED*30CHIP -20~60 -30~70 Unit pixels mm mm - PCS ℃ ℃ Pixel Arrangement AZ DISPLAYS 3 ATM0700L26B-T(AZ DISPLAYS) TFT MODULE V1.0 2. PIN ASSIGNMENT 2.1 FPC Connector is used for the module electronics interface. The recommended model is FH26-39S-0.3SHW manufactured by Hirose Pin NO. Function Descriptions Symbol 1 Common Voltage NC 2 Digital Power VDD 3 Digital Power VDD 4 Not connect NC 5 NC 7 Not connect Standby mode, Normally pulled high STBYB = “1”, normal operation STBYB = “0”, timing controller, source driver will turn off, all output are High-Z Power ground GND 8 - LVDS differential data input RXIN0- 9 LVDS differential data input RXIN0+ 6 STBYB 10 Power ground GND 11 - LVDS differential data input RXIN1- 12 LVDS differential data input RXIN1+ 13 Power ground GND 14 - LVDS differential data input RXIN2- 15 LVDS differential data input RXIN2+ 16 Power ground GND 17 - LVDS differential clock input RXCLKIN- 18 +LVDS differential clock input RXCLKIN+ 19 Power ground GND 20 - LVDS differential data input RXIN3- 21 LVDS differential data input RXIN3+ 22 23 24 Power ground Not connect Power ground GND NC GND 25 Not connect NC 26 Not connect NC 27 Not connect NC AZ DISPLAYS 4 ATM0700L26B-T(AZ DISPLAYS) TFT MODULE V1.0 28 Not connect NC 29 Power ground GND 30 LED Cathode LED- 31 LED Cathode LED- 32-37 Not connect NC 38 LED Anode LED+ 39 LED Anode LED+ AZ DISPLAYS 5 4 1 41.25± 0.5 Stiffener 0.3± 0.05 20.00± 0.5 7.50± 0.3 TP LAYOUT YD XR YD XR X2 (1.90) 1.00± 0.2 (1.40) Parameters: 1 Operating voltage: DC5V; 2 Operating force: 40~100g; 3 Linearity ≤1.5%;Insulation resistance>10MΩ,(25VDC); 4 Working temperature: -20℃ ~ +70℃ 20% ~ 90%RH; 5 Storage temperature: -20℃ ~ +80℃ 20% ~ 85%RH; 6 Transmittance >75%; 7 Structure: Film + Glass; 8 ITO-Film: Anti glare; 9 Response time<10ms; 10 electrode resistance: 200~900 ohms; 11 Unspecified tolerance:+/-0.3mm XL *91.00(TP AA) 92.00(TP VA) *98.90(TP OUTLINE) YU XL 7" 1024*600 YU 1.6± 0.2 Double - side tape *160.20(TP OUTLINE) 155.60(TP VA) *154.60(TP AA) Side 4.50± 0.3 Front ITO Glass Rear AZ DISPLAYS Conductor Front 0.50 0.50 P1*(4-1)=3.00± 0.2 Double -side tape Rear (1.90) ATM0700L26B-T(AZ DISPLAYS) TFT MODULE V1.0 2.2 Touch Panel Section FPC Connector is used for the module electronics interface. The recommended model is FH12-4S-1SH manufactured by Hirose. (1.40) 6 (3.00) (2.50) (2.00) (0.20) AZ DISPLAYS *90.00 LCD(AA) *91.00(TP AA) 92.00(TP VA) *98.90(TP OUTLINE) *99.40 (LCD OUTLINE) 83.40± 0.50 H=0.3 Components 80/80/80/80 7" 1024*600 0.30 *0.30 11.40 *12.00 Components 1 39 *160.60 (LCD OUTLINE) *160.20(TP OUTLINE) *155.60(TP VA) 154.60(TP AA) *153.60 LCD(AA) (0.20) (2.50) (3.00) (3.50) 40.95± 1 20.20± 1 *0.20 1.00± 0.2 *0.30± 0.05 1.90 MAX 3.50 SLA 0.50 0.50 P1*(4-1)=3.00± 0.2 *4.5Max(Total thickness) 2.65± 0.2(LCM thickness) 1.40± 0.2(TP thickness) K A ATM0700L26B-T(AZ DISPLAYS) TFT MODULE V1.0 3. Mechanical Specification 3.50 *2.65 40.95± 0.50 7 ATM0700L26B-T(AZ DISPLAYS) TFT MODULE V1.0 4. Electrical Units 4.1 Electrical Specification <Table3. Electrical specifications> Item Symbol Unit Power voltage Input signal voltage Value Note Min Typ Max DVDD AVDD VGH VGL V V V V 3.0 19 -6 3.2 9.0 20 -7 3.6 23 -8 VCOM V 3.0 3.6 4.2 - Operating TOP ℃ -20 to +60 Temperature Storage Temperature TST ℃ -30 to +70 Notes: 1. VGH is TFT Gate operating voltage. 2. VGL is TFT Gate operating voltage.The low voltage level of VGL signal must be fluctuates with same phase as Vcom. 3. Be sure to apply DVDD and VGL to the LCD first, and then apply VGH. 4. DVDD setting should match the signals output voltage (refer to Note 3) of customer’s system board. 5. DCLK,HS,VS,RESET,U/D, L/R,DE,R0~R7,G0~G7,B0~B7,MODE,DITHB. 4.2 Electrical characteristics (Ta=25℃) 4.2.1 TFT-LCD Current Consumption Table 3.2: Item Symbol Unit Gate on power current IVGH mA VGH=20.0V - Gate off power current IVGL mA VGL=-7.0V Analog power current IVDD mA IAVDD mA Analog power current AZ DISPLAYS Test Condition Min Typ. Max Note - - - - - - - VDD=3.2V - - - - AVDD=9.0V - - 8 ATM0700L26B-T(AZ DISPLAYS) TFT MODULE V1.0 4.3 Back-light Specification Table 4.3 Back-light Specification Item Supply Voltage Supply Current Symbol VF IF Uniformity B Color AZ DISPLAYS Conditions Min. Only Backlight Backlight Current IF=200mA 8.0 80 Typ. Max. Unit 9.6 10.0 20*10=200 V mA - - (%) White 9 ATM0700L26B-T(AZ DISPLAYS) TFT MODULE V1.0 5Timing Characteristics 5.1. Timing characteristics of input signals 5.2.Timing sequence(Timing chart) 5.2.1Horizontal Timing Sequence AZ DISPLAYS 10 ATM0700L26B-T(AZ DISPLAYS) TFT MODULE V1.0 5.2.2 Vertical Timing Sequence 5.2.3 LVDS Input Data mapping 6Bit LVDS input 8Bit LVDS input AZ DISPLAYS 11 ATM0700L26B-T(AZ DISPLAYS) TFT MODULE V1.0 6 Optical Specifications Item of electro-optical characteristics Symbol Condition Min Typ Max Contrast ratio CR Ø =0° 700 900 -- Surface Luminance YL - 480 520 -- Color saturation NTSC Ton - -- Ø =0° --- 15 15 Top 70 80 -- Bottom 70 80 -- Left 70 80 -- Right 70 -- ------- 80 0.297 0.337 0.618 0.328 0.282 0.538 0.142 0.168 Response time Viewing angle range Tof Ø =0° White Module Chromaticity CIE(x,y) Red Green Blue x y x y x y x y Ø =0° -- Unit Remark Note1 Cd/ M2 % ms Note1 Note2 Note3 ------- Note4 Transmittance Trans -- -- - -- % Note5 Cross talk Ct -- -- - -- % Note6 Notes(1) :1. All input terminals LCD panel must be ground while measuring the center area of the panel. 2. Contrast measurements shall be made at viewing angle of Θ= 0 and at the center of the LCD surface. Luminance shall be measured with all pixels in the view field set first to white, then to the dark (black) state. (see Figure 4) Luminance Contrast Ratio (CR) is defined mathematically Note (2) Definition of Response Time (TR, TF): AZ DISPLAYS 12 ATM0700L26B-T(AZ DISPLAYS) TFT MODULE V1.0 Note (3) Definition of viewing Angle: Viewing angle is the angle at which the contrast ratio is greater than 10. The viewing angles are determined for the horizontal or 3, 9 o‟clock direction and the vertical or 6, 12 o‟clock direction with respect to the optical axis which is normal to the LCD surface. Note (4) Definition of optical measurement system. The optical characteristics should be measured in dark room. The optical properties are measured at the center point of the LCD screen,(Response time is measured by Photo detector TOPCON BM-7, other items are measured by BM-5A/Field of view :1 ° /Height 500mm.) AZ DISPLAYS 13 ATM0700L26B-T(AZ DISPLAYS) TFT MODULE V1.0 Note (5) Definition of Transmittance Where LMOD defined as measured luminance at center point of MOD with ” White” state LBL defined as measured luminance at center point of Backlight Unit with same MOD. The Backlight Unit has composite optical films, except “gain” characteristic optical films. Tr% = (LMOD / LBL )*100% AZ DISPLAYS 14 ATM0700L26B-T(AZ DISPLAYS) TFT MODULE V1.0 7 Reliability Test Items Test NO. Item Test Condition Check Time 1 High temp storage T=70 240hrs 2 Low temp storage T=-30 240hrs 3 High temp operation T=60 240hrs 4 Low temp operation T= -20 240hrs 5 High temp&high humidity T=50 H=90% 240hrs Reliability Test Criteria: Display function should be no change under normal operating condition. 8. Handling Precautions 8.1 Safety The liquid crystal in the LCD is poisonous. Keep away from your mouth and eyes. If the liquid crystal contacts with your skin, mouse or clothes, use soap to wash it off immediately. 8.2 Handling i. The LCD panel is made by thin glass. Prevent the panel from mechanical shock or putting excessive force on its surface. ii. The polarizer attached on the display is very easy to be damaged, handle it with special attention. iii. To avoid contamination on the display surface, do not touch the display surface with bare hands. iv. The transparent electrodes may be disconnected if you use the LCD panel under dew-condensing environment. v. The characteristics of the semiconductor devices may be affected when they are exposed to light, possibly resulting in malfunctioning of the ICs. To prevent such malfunctioning of the ICs, make sure the application and the mounting of the panel are designed so that the IC is not exposed to light. 8.3 Static Electricity Ground soldering iron tips, tools and testers when you operate. Also ground your body when handling the products and store the products in an anti-electrostatic container. 8.4 Storage Store the products in a dark place where the temperature is within the range of 25±10 and with low humidity (65%RH or less). Do not store the LCD product in an atmosphere containing organic solvents or corrosive gases. 8.5 Cleaning Do not wipe the polarizer with dry cloth, as it might cause scratching. Wipe the polarizer with a soft cloth soaked with petroleum IPA. Other chemical might damage the panel. AZ DISPLAYS 15 ATM0700L26B-T(AZ DISPLAYS) TFT MODULE V1.0 9.INSPECTION CRITERION OUTGOING QUALITY STANDARD PAGE 1 OF 6 TITLE:FUNCTIONAL TEST & INSPECTION CRITERIA LCM Product This specification is made to be used as the standard acceptance/rejection criteria for Color mobile phone LCM with touch panel. 1 Sample plan Sampling plan according to GB/T2828.1-2003/ISO 2859-1:1999, normal level 2 and based on: Major defect: AQL 0.65 Minor defect: AQL 1.5 2 Inspection condition Viewing distance for cosmetic inspection is about 30 cm with bare eyes, and under an environment of 20~40W light intensity, all directions for inspecting the sample should be within 45° against perpendicular line. 3 Definition of inspection zone in LCD Zone A: character/Digit area Zone B: viewing area except Zone A (Zone A + Zone B=minimum Viewing area) Zone C: Outside viewing area (invisible area after assembly in customer’s product) Fig.1 Inspection zones in an LCD. Note: As a general rule, visual defects in Zone C are permissible, when it is no trouble for quality and assembly of customer’s product. OUTGOING QUALITY STANDARD AZ DISPLAYS PAGE 2 OF 6 16 ATM0700L26B-T(AZ DISPLAYS) TFT MODULE V1.0 TITLE:FUNCTIONAL TEST & INSPECTION CRITERIA LCM Product 4 Inspection standards 4.1 Major Defect Item NO. Items to be Classification 4.1.1 1) No display 2) Display abnormally All functiona 3) Missing vertical,horizontal segment defects defects 4) Short circuit 5) Back-light no lighting, flickering and abnormal lighting. 4.1.2 Missing 4.1.3 Outline dimension 4.1.4 linearity Classificatio of defects Inspection Standard Major Component Missing Overall outline dimension beyond the drawing is not allowed. No more than 1.5% 4.2 Cosmetic Defect 4.2.1 Spots defect Item NO Items to be Classification Classificatio of defects Inspection Standard For dark/white spot, size Φ is define as: Clear Spots 4.2.1 Black and white Spot defect Pinhole, Foreign Particle, polarizer Dirt y X Φ=(X+Y)/2 1. Acceptable Qty Zone Size(mm) A B Φ≤0.1 Ignore 0.1<Φ≤0.15 2 0.15<Φ≤0.2 1 0.2 <Φ 0 Minor C Ignore OUTGOING QUALITY STANDARD PAGE 3 OF 6 TITLE:FUNCTIONAL TEST & INSPECTION CRITERIA LCM Product 3. Dim Spots Minor Circle shaped and AZ DISPLAYS 17 ATM0700L26B-T(AZ DISPLAYS) TFT MODULE V1.0 dim edged defects Acceptable Qty Zone A Size(mm) B Φ≤0.20 Ignore 0.20<Φ≤0.40 2 0.40<Φ≤0.60 1 0.60 <Φ 0 C Ignore 4.2.2 Line defect Item NO Items to be Classification size(mm) Line defect Black line, White line, Foreign material on polarizer 4.2.2 Classificatio of defects Inspection Standard Acceptable Qty zone L(Length) W(Width) Ignore W≤0.02 Ignore L≤3.0 0.02<W≤0.03 2 L≤2.0 0.03<W≤0.05 1 0.05<W Define as spot defect A B C Minor Ignore The line can be seen after mobile phone in the operating condition: size(mm) Foreign material on TP film Acceptable Qty zone L(Length) W(Width) Ignore W≤0.03 Ignore L≤5.0 0.03<W≤0.05 3 0.05<W Define as spot defect A B Minor C Ignore OUTGOING QUALITY STANDARD PAGE 4 OF 6 TITLE:FUNCTIONAL TEST & INSPECTION CRITERIA LCM Product AZ DISPLAYS 18 ATM0700L26B-T(AZ DISPLAYS) TFT MODULE V1.0 Acceptable Qty Zone A Size(mm) 4.2.4 Polarize Air bubble B Φ≤0.20 Ignore 0.20<Φ≤0.30 2 0.30<Φ≤0.50 1 0.50 <Φ 0 4.2.3 LCD chip defect Items to be Item NO Classification C Minor Ignore Classificatio of defects Inspection Standard (i) Chips on corner A:LCD Glass defect 4.2.5 Glass defect X(mm) Y(mm) Z(mm) ≤2.0 ≤S Disregard Notes: S=contact pad length Chips on the corner of terminal shall not be allowed to extend into the ITO pad or expose perimeter seal. Minor (ii)Usual surface cracks A:LCD Glass defect OUTGOING QUALITY STANDARD TITLE:FUNCTIONAL TEST & INSPECTION CRITERIA PAGE 5 OF 6 LCM Product (iii) Crack Cracks tend to break are not allowed. Major AZ DISPLAYS 19 ATM0700L26B-T(AZ DISPLAYS) TFT MODULE V1.0 4.3 Parts Defect Item NO 4.3.1 Items to be Classification Parts contraposition 4.3.2 SMT 1、Not allow IC and FPC/heat-seal lead width is more than 50% beyond lead pattern. 2、Not allow chip or solder component is off center more than 50% of the pad outline. Major According to the <Acceptability of electronic assemblies> IPC-A-610C class 2 standard. Component missing or function defect are Major defect, the others are Minor defect. OUTGOING QUALITY STANDARD TITLE:FUNCTIONAL TEST & INSPECTION CRITERIA AZ DISPLAYS Classificatio of defects Inspection Standard PAGE 6 OF 6 LCM Product 20