339-9SUGSURSUBW/S1182/MS

339-9SUGSURSUBW/S1182/MS
Features
˙Popular T-1 3/4 round package.
˙High efficiency.
˙Available on tape and reel.
˙Built in red, green, and blue chips.
˙The product itself will remain within RoHS
compliant version
Descriptions
˙The series is specially designed for
applications requiring higher brightness
˙The LED lamps are available with different
olors, intensities, epoxy, colors, etc.
Applications
˙Status indicators.
˙Commercial use.
˙Advertising Signs.
˙Message board
Device Selection Guide
LED Part No.
339-9SUGSURSUBW/S1182/MS
1
Revision
Chip
Material
Emitted Color
AlGaInP
Brilliant Red
InGaN
Brilliant Green
Lens Color
White diffused
www.everlight.com
Copyright©
No: DLE-0003486_Rev.2
: 2 2014 Everlight All Rights Reserved. Release Date : July,2014/11 IssueRelease
Date:2014-12-02
08:10:49.0
LifecyclePhase:
Expired Period: Forever
DATASHEET
LAMP
339-9SUGSURSUBW/S1182/MS
InGaN
Blue
Notes:
˙All dimensions are in millimeters, tolerance is 0.25mm except being specified.
˙Lead spacing is measured where the lead emerges from the package.
˙Protruded resin under flange is 1.5mm Max LED.
2
Revision
www.everlight.com
Copyright
No: DLE-0003486_Rev.2
: 2 © 2014, Everlight All Rights Reserved. Release Date :July,12014/11. Issue
Release
Date:2014-12-02
08:10:49.0
LifecyclePhase:
Expired Period: Forever
DATASHEET
LAMP
339-9SUGSURSUBW/S1182/MS
Absolute Maximum Ratings (Ta=25℃)
Parameter
Symbol
Blue
Green
Red
Units
Forward Current
IF
30
30
50
mA
Pulse Forward Current
(Duty1/10@ 1KHz)
IFP
100
100
100
mA
Operating Temperature
Topr
-40 ~ +85
℃
Storage Temperature
Tstg
-40 ~ +100
℃
Electrostatic Discharge
ESD
Soldering Temperature
Tsol
Power Dissipation
Pd
Reverse Voltage
VR
1000
1000
2000
260
110
110
5
V
℃
120
mW
V
*Notes: Soldering time≦5 seconds.
3
Revision
www.everlight.com
Copyright
No: DLE-0003486_Rev.2
: 2 © 2014, Everlight All Rights Reserved. Release Date :July,12014/11. Issue
Release
Date:2014-12-02
08:10:49.0
LifecyclePhase:
Expired Period: Forever
DATASHEET
LAMP
339-9SUGSURSUBW/S1182/MS
Electro-Optical Characteristics (Ta=25℃)
Parameter
Symbol
Color
Min.
Typ.
Max.
Unit
R IF=15 mA
R/G/B
Luminous Intensity
Viewing Angle
IV
2θ1/2
Three in
1800
----
4500
mcd
VF
B IF=9 mA
R/G/B
R IF=15 mA
Three in
-----
65
-----
deg
IR
G IF=15 mA
B IF=9 mA
SUR
-----
2.0
-----
R IF=15 mA
SUG
-----
3.0
-----
G IF=15 mA
SUB
-----
2.75
-----
SUR
1.6
2.0
2.4
SUG
2.8
3.2
3.6
G IF=20mA
SUB
2.8
3.2
3.6
B IF=20mA
SUR
Reverse Current
G IF=15 mA
one
one
Forward Voltage
Condition
SUG
V
B IF=9 mA
R IF=20 mA
10
-----
SUB
-----
50
μA
VR=5V
50
*Measurement Uncertainty of Luminous Intensity: ±10%
*Measurement Uncertainty of Forward Voltage: ±0.1V
4
Revision
www.everlight.com
Copyright
No: DLE-0003486_Rev.2
: 2 © 2014, Everlight All Rights Reserved. Release Date :July,12014/11. Issue
Release
Date:2014-12-02
08:10:49.0
LifecyclePhase:
Expired Period: Forever
DATASHEET
LAMP
339-9SUGSURSUBW/S1182/MS
Luminous Intensity Combination
(mcd at R IF=15mA G IF=15mA B IF=9mA)
5
Revision
Rank
Min
Max
M
1800
2250
N
2250
2850
P
2850
3600
Q
3600
4500
www.everlight.com
Copyright
No: DLE-0003486_Rev.2
: 2 © 2014, Everlight All Rights Reserved. Release Date :July,12014/11. Issue
Release
Date:2014-12-02
08:10:49.0
LifecyclePhase:
Expired Period: Forever
DATASHEET
LAMP
339-9SUGSURSUBW/S1182/MS
Color Ranks (Ta=25℃)
(R IF=15mA G IF=15mA B IF=9mA , Three devices are lit simultaneously.)
*Measurement uncertainty of the color coordinates:±0.01
6
Revision
www.everlight.com
Copyright
No: DLE-0003486_Rev.2
: 2 © 2014, Everlight All Rights Reserved. Release Date :July,12014/11. Issue
Release
Date:2014-12-02
08:10:49.0
LifecyclePhase:
Expired Period: Forever
DATASHEET
LAMP
339-9SUGSURSUBW/S1182/MS
Typical Electro-Optical Characteristics Curves
Relative Intensity vs. Wavelength
Forward Current vs. Forward Voltage
Relative Intensity vs. Forward Current
Forward Current vs. Ambient Temp.
Chromaticity Coordinate vs. Forward Current
Relative Intensity vs. Angle Displacement
O
90
O
60
O
30
O
0
10O
Relative Luminusity
1.0
O
20
30O
O
40
O
50
O
60
0.5
O
70
O
80
0
O
0
0.5
90
1.0
Radiation Angle
7
Revision
www.everlight.com
Copyright
No: DLE-0003486_Rev.2
: 2 © 2014, Everlight All Rights Reserved. Release Date :July,12014/11. Issue
Release
Date:2014-12-02
08:10:49.0
LifecyclePhase:
Expired Period: Forever
DATASHEET
LAMP
339-9SUGSURSUBW/S1182/MS
Packing Specification
■
Anti-electrostatic bag
Label
Pb
EL ECTROSTATIC ELECTRONAGNETIC
MAGNET IC OR RADIOACTIVE RELDS
anti-static for 750
■
Inner Carton
■
■
Outside Carton
■
8
Revision
Label Form Specification
CPN: Customer’s Production Number
P/N : Production Number
QTY: Packing Quantity
CAT: Rank of Luminous Intensity
HUE: Rank of Dominant Wavelength
REF: Reference
LOT No: Lot Number
MADE IN TAIWAN: Production Place
Packing Quantity
1. 500 PCS/1 Bag, 5 Bags/1 Inner Carton
2. 10 Inner Cartons/1 Outside Carton
www.everlight.com
Copyright
No: DLE-0003486_Rev.2
: 2 © 2014, Everlight All Rights Reserved. Release Date :July,12014/11. Issue
Release
Date:2014-12-02
08:10:49.0
LifecyclePhase:
Expired Period: Forever
DATASHEET
LAMP
339-9SUGSURSUBW/S1182/MS
Notes
1. Lead Forming

During lead formation, the leads should be bent at a point at least 3mm from the base of the epoxy
bulb.

Lead forming should be done before soldering.

Avoid stressing the LED package during leads forming. The stress to the base may damage the
LED’s characteristics or it may break the LEDs.

Cut the LED leadframes at room temperature. Cutting the leadframes at high temperatures may
cause failure of the LEDs.

When mounting the LEDs onto a PCB, the PCB holes must be aligned exactly with the lead
position of the LED. If the LEDs are mounted with stress at the leads, it causes deterioration of the
epoxy resin and this will degrade the LEDs.
2. Storage

The LEDs should be stored at 30°C or less and 70%RH or less after being shipped from Everlight
and the storage life limits are 3 months. If the LEDs are stored for 3 months or more, they can be
stored for a year in a sealed container with a nitrogen atmosphere and moisture absorbent material.

Please avoid rapid transitions in ambient temperature, especially, in high humidity environments
where condensation can occur.
3. Soldering

Careful attention should be paid during soldering. When soldering, leave more then 3mm from
solder joint to epoxy bulb, and soldering beyond the base of the tie bar is recommended.

Recommended soldering conditions:
Hand Soldering
DIP Soldering
Temp. at tip of iron
300℃ Max. (30W
Max.)
Preheat temp.
100℃ Max. (60 sec
Max.)
Soldering time
3 sec Max.
Bath temp. & time
260 Max., 5 sec Max
Distance
3mm Min.(From
solder joint to
epoxy bulb)
Distance
3mm Min. (From
solder joint to epoxy
bulb)
9
Revision
www.everlight.com
Copyright
No: DLE-0003486_Rev.2
: 2 © 2014, Everlight All Rights Reserved. Release Date :July,12014/11. Issue
Release
Date:2014-12-02
08:10:49.0
LifecyclePhase:
Expired Period: Forever
DATASHEET
LAMP
339-9SUGSURSUBW/S1182/MS
Recommended soldering profile
laminar wave
Fluxing
Prehead

Avoiding applying any stress to the lead frame while the LEDs are at high temperature
particularly when soldering.

Dip and hand soldering should not be done more than one time

After soldering the LEDs, the epoxy bulb should be protected from mechanical shock or
vibration until the LEDs return to room temperature.

A rapid-rate process is not recommended for cooling the LEDs down from the peak temperature.

Although the recommended soldering conditions are specified in the above table, dip or
handsoldering at the lowest possible temperature is desirable for the LEDs.

Wave soldering parameter must be set and maintain according to recommended temperature and
dwell time in the solder wave.
4. Cleaning
 When necessary, cleaning should occur only with isopropyl alcohol at room temperature for a
duration of no more than one minute. Dry at room temperature before use.
Do not clean the LEDs by the ultrasonic. When it is absolutely necessary, the influence of ultrasonic
cleaning on the LEDs depends on factors such as ultrasonic power and the

cause damage to the LED.
5. Heat Management
 Heat management of LEDs must be taken into consideration during the design stage of LED
application. The current should be de-rated appropriately by referring to the de-rating curve
found in each product specification.
10
Revision
www.everlight.com
Copyright
No: DLE-0003486_Rev.2
: 2 © 2014, Everlight All Rights Reserved. Release Date :July,12014/11. Issue
Release
Date:2014-12-02
08:10:49.0
LifecyclePhase:
Expired Period: Forever
DATASHEET
LAMP
339-9SUGSURSUBW/S1182/MS

The temperature surrounding the LED in the application should be controlled. Please refer to the
data sheet de-rating curve.
6. ESD (Electrostatic Discharge)
 Electrostatic discharge (ESD) or surge current (EOS) can damage LEDs.

An ESD wrist strap, ESD shoe strap or antistatic gloves must be worn whenever handling LEDs.

All devices, equipment and machinery must be properly grounded.

Use ion blower to neutralize the static charge which might have built up on surface of the LEDs
plastic lens as a result of friction between LEDs during storage and handing.
7. Other
 Above specification may be changed without notice. EVERLIGHT will reserve authority on
material change for above specification.

When using this product, please observe the absolute maximum ratings and the instructions for
using outlined in these specification sheets. EVERLIGHT assumes no responsibility for any
damage resulting from use of the product which does not comply with the absolute maximum
ratings and the instructions included in these specification sheets.

These specification sheets include materials protected under copyright of EVERLIGHT
corporation. Please don’t reproduce or cause anyone to reproduce them without EVERLIGHT’s
consent.
EVERLIGHT ELECTRONICS CO., LTD.
Office: No 25, Lane 76, Sec 3, Chung Yang Rd,
Tucheng, Taipei 236, Taiwan, R.O.C
11
Revision
Tel: 886-2-2267-2000, 2267-9936
Fax: 886-2267-6244, 2267-6189, 2267-6306
http:\\www.everlight.com
www.everlight.com
Copyright
No: DLE-0003486_Rev.2
: 2 © 2014, Everlight All Rights Reserved. Release Date :July,12014/11. Issue
Release
Date:2014-12-02
08:10:49.0
LifecyclePhase:
Expired Period: Forever