AMD SP5100
Register Programming
Requirements
Technical Reference Manual
Rev. 3.02
P/N: 44414_sp5100_rpr_pub_3.02
2012 Advanced Micro Devices, Inc.
.
Trademarks
AMD, the AMD Arrow logo, Athlon, and combinations thereof are trademarks of Advanced Micro Devices,
Inc.
HyperTransport is a licensed trademark of the HyperTransport Technology Consortium.
Microsoft and Windows are registered trademarks of Microsoft Corporation.
PCI Express and PCIe are registered trademarks of PCI-SIG.
Other product names used in this publication are for identification purposes only and may be trademarks
of their respective companies.
Disclaimer
The contents of this document are provided in connection with Advanced Micro Devices, Inc. ("AMD")
products. AMD makes no representations or warranties with respect to the accuracy or completeness of
the contents of this publication and reserves the right to make changes to specifications and product
descriptions at any time without notice. No license, whether express, implied, arising by estoppel, or
otherwise, to any intellectual property rights are granted by this publication. Except as set forth in AMD's
Standard Terms and Conditions of Sale, AMD assumes no liability whatsoever, and disclaims any
express or implied warranty, relating to its products including, but not limited to, the implied warranty of
merchantability, fitness for a particular purpose, or infringement of any intellectual property right.
AMD's products are not designed, intended, authorized or warranted for use as components
in systems intended for surgical implant into the body, or in other applications intended to
support or sustain life, or in any other application in which the failure of AMD's product could
create a situation where personal injury, death, or severe property or environmental damage
may occur. AMD reserves the right to discontinue or make changes to its products at any
time without notice.
Table of Contents
1 Introduction ................................................................................................................ 7
1.1 About This Manual........................................................................................................................ 7
1.2 AMD SP5100 Block Diagram....................................................................................................... 8
1.3 Register Reference Information .................................................................................................... 9
2 ACPI/SMBUS Controller (bus-0, dev-20, fun-0)................................................ 10
2.1
2.2
2.3
2.4
2.5
2.6
2.7
2.8
2.9
2.10
2.11
2.12
2.13
2.14
2.15
2.16
2.17
2.18
2.19
2.20
2.21
2.22
2.23
2.24
2.25
2.26
2.27
2.28
2.29
2.30
2.31
2.32
2.33
2.34
2.35
2.36
Enabling Legacy Interrupt ........................................................................................................... 10
Unblocked SMI Command Port .................................................................................................. 10
WakeIO Base Address ................................................................................................................ 10
C-State and VID/FID Change ..................................................................................................... 10
Enable C1e Stutter Timer and Limit Link Disconnect to < 20 ms ............................................. 13
MTC1e and FID VID Setting ...................................................................................................... 14
C1e Exit on Assertion of IDLE Exit# (for A15 Only) ................................................................ 14
Support for Entering C1e on HALT# Message (for A15 Only) .................................................. 14
Enabling Non-Posted Memory Write .......................................................................................... 15
Therm Trip Settings .................................................................................................................... 15
Sx State Settings .......................................................................................................................... 15
Output Drive Strength Settings ................................................................................................... 16
SUS_STAT# Enhancement ......................................................................................................... 16
Interrupt Routing/Filtering .......................................................................................................... 16
IO Trap Settings .......................................................................................................................... 17
Enabling ACPI Registers ............................................................................................................ 17
Legacy DMA Prefetch Enhancement .......................................................................................... 18
USB Set BM_STS ....................................................................................................................... 18
Enabling Spread Spectrum .......................................................................................................... 18
PCIe Native Mode ..................................................................................................................... 19
Hardware Monitor ....................................................................................................................... 19
Cir Interrupt Config..................................................................................................................... 20
SMBUS PCI Config .................................................................................................................... 20
IMC Access Control .................................................................................................................... 20
CPU Reset ................................................................................................................................... 21
Disabling Legacy USB Fast SMI# .............................................................................................. 21
SMBUS1 Programming Sequence .............................................................................................. 21
ACPI System Clock Setting ........................................................................................................ 23
Integrated Pull-up and Pull-down Settings .................................................................................. 23
Revision ID ................................................................................................................................. 23
Alternate Pin for 14 MHz Clock Input ........................................................................................ 24
Gevent5 as GPIO ......................................................................................................................... 24
SMBUS Block Write Filtering .................................................................................................... 25
SMBUS Sequence ....................................................................................................................... 25
Software Clock Throttle Period................................................................................................... 25
Unconditional Shutdown ............................................................................................................. 26
2012 Advanced Micro Devices, Inc.
AMD SP5100 Register Programming Requirements
TOC
Page 3
2.37
2.38
2.39
2.40
2.41
2.42
2.43
Watchdog Timer Resolution ....................................................................................................... 26
Supporting IDLE_EXIT# from CPU .......................................................................................... 27
Supporting HALT Message to Generate C1e.............................................................................. 27
LDT_PWRGD De-assertion with SLP_S3# ............................................................................... 28
Programmable Interrupt Controller Arbitration .......................................................................... 28
HPET MSI Setting ...................................................................................................................... 28
SMAF Matching Setting ............................................................................................................. 29
3 LPC Controller (bus-0, dev-20, fun-3) ................................................................ 30
3.1 IO / Mem Decoding..................................................................................................................... 30
3.2 SPI Bus ........................................................................................................................................ 30
4 A-Link Express Settings - Indirect I/O Access................................................. 31
4.1
4.2
4.3
4.4
4.5
4.6
4.7
4.8
4.9
4.10
4.11
4.12
4.13
4.14
4.15
4.16
4.17
4.18
4.19
4.20
Defining AB_REG_BAR ............................................................................................................ 31
Clearing AB_INDX..................................................................................................................... 31
Enabling Upstream DMA Access ................................................................................................ 32
IDE/PCIB Prefetch Settings ........................................................................................................ 32
OHCI Prefetch Settings ............................................................................................................... 32
B-Link Client’s Credit Variable Settings for the Downstream Arbitration Equation ................. 33
Enabling Additional Address Bits Checking in Downstream Register Programming ................ 33
Set B-Link Prefetch Mode........................................................................................................... 33
Enabling Detection of Upstream Interrupts................................................................................. 34
Enabling Downstream Posted Transactions to Pass Non-Posted Transactions ........................... 34
Programming Cycle Delay for AB and BIF Clock Gating.......................................................... 34
Enabling AB and BIF Clock Gating............................................................................................ 35
Enabling AB Int_Arbiter Enhancement ...................................................................................... 35
Enabling Requester ID ................................................................................................................ 35
Selecting the LPC FRAME# Assertion Timing on Power-up..................................................... 35
SMI IO Write .............................................................................................................................. 36
Reset CPU on Sync Flood ........................................................................................................... 36
Enabling Posted Pass Non-Posted Downstream ......................................................................... 36
Enabling Posted Pass Non-Posted Upstream .............................................................................. 37
64 bit Non-Posted Memory Write Support ................................................................................. 37
5 PCIB (PCI-bridge, bus-0, dev-20, fun-04)........................................................... 38
5.1
5.2
5.3
5.4
5.5
5.6
5.7
5.8
5.9
Enabling PCI-bridge Subtractive Decode ................................................................................... 38
PCI-bridge Upstream Dual Address Window ............................................................................. 38
PCI Bus 64-byte DMA Read Access .......................................................................................... 38
PCI Bus DMA Write Cacheline Alignment ................................................................................ 39
Master Latency Timer ................................................................................................................. 39
DMA Read Command Match ..................................................................................................... 39
Enabling Idle To Gnt# Check...................................................................................................... 40
GNT# Timing Adjustment .......................................................................................................... 40
Enabling Fast Back to Back Retry .............................................................................................. 40
2012 Advanced Micro Devices, Inc.
AMD SP5100 Register Programming Requirements
TOC
Page 4
5.10
5.11
5.12
5.13
5.14
Enabling Lock Operation ............................................................................................................ 40
Enabling Additional Optional PCI Clock (PCICLK5) ................................................................ 41
Enabling One-Prefetch-Channel Mode ....................................................................................... 41
Disabling PCIB MSI Capability .................................................................................................. 41
Adjusting CLKRUN# .................................................................................................................. 42
6 USB – OHCI & EHCI controllers (bus-0, dev-18/19, fun-00 ~02/ bus-0, dev20, fun-05)........................................................................................................................ 43
6.1
6.2
6.3
6.4
6.5
6.6
6.7
6.8
6.9
6.10
6.11
6.12
6.13
6.14
6.15
6.16
6.17
6.18
6.19
6.20
6.21
6.22
6.23
6.24
6.25
Enabling/Disabling OHCI and EHCI Controllers ....................................................................... 43
USB Device Support to Wake Up System from S3/S4 State ...................................................... 44
USB S4/S5 Wakeup or PHY Power Down Support ................................................................... 44
USB PHY Auto Calibration Setting ............................................................................................ 44
USB Reset Sequence ................................................................................................................... 45
USB Advanced Sleep Control ..................................................................................................... 45
USB 48 MHz Clock Source Settings .......................................................................................... 45
Adjusting USB 2.0 Ports Driving Strength ................................................................................. 46
In and Out Data Packet FIFO Threshold ..................................................................................... 46
OHCI MSI Function Setting ....................................................................................................... 47
EHCI Advance Asynchronous Enhancement.............................................................................. 47
EHCI Advance PHY Power Savings........................................................................................... 47
Enabling Fix for EHCI Controller Driver Yellow Sign Issue ..................................................... 48
Enabling Fix to Cover the Corner Case S3 Wake Up Issue ........................................................ 48
EHCI Async Park Mode .............................................................................................................. 48
MSI Feature in USB 2.0 Controller............................................................................................. 48
EHCI Dynamic Clock Gating Feature......................................................................................... 49
USB 1.1 ISO OUT Devices/Speaker Noise ................................................................................ 49
USB Controller DMA Read Delay Tolerant ............................................................................... 49
Async Park Mode ........................................................................................................................ 50
Resume Reset Timing ................................................................................................................. 50
Disable Async QH Cache ............................................................................................................ 50
Advance Async Enhancement ..................................................................................................... 51
USB Periodic Cache Setting ....................................................................................................... 51
USB PID_ERROR_CHECKING ................................................................................................ 52
7 SATA: dev-17, func-0 ............................................................................................. 53
7.1
7.2
7.3
7.4
7.5
7.6
7.7
Enabling SATA ........................................................................................................................... 53
SATA Initialization ..................................................................................................................... 53
Disabling SATA .......................................................................................................................... 54
Disabling Unused SATA Ports ................................................................................................... 55
SATA Subclass Programming Sequence .................................................................................... 56
SATA PHY Programming Sequence .......................................................................................... 57
SATA Identification Programming Sequence for IDE Mode ..................................................... 58
7.7.1 SATA Drive Detection....................................................................................................................... 58
7.8 Restoring SATA Registers after S3 Resume State ...................................................................... 59
2012 Advanced Micro Devices, Inc.
AMD SP5100 Register Programming Requirements
TOC
Page 5
7.9 Internal and External SATA Ports Indication Registers.............................................................. 60
7.10 Aggressive Link Power Management ......................................................................................... 60
7.11 SATA MSI and D3 Power State Capability ................................................................................ 61
7.11.1 SATA MSI Settings ............................................................................................................................. 61
7.11.2 D3 Power State Settings ...................................................................................................................... 61
7.11.3 Capability Pointer Settings .................................................................................................................. 62
7.12 Disabling CCC (Command Completion Coalescing) Support .................................................... 62
8 LPC (bus-0, dev-20, fun-03) .................................................................................. 63
8.1 Enabling/Disabling LPC Controller ............................................................................................ 63
8.2 Parallel Port ECP Mode Support ................................................................................................. 63
9 IDE Controller (bus-0, dev-20, fun-01) .............................................................. 64
9.1 Disable Second IDE MSI Capability........................................................................................... 64
9.2 Enable IDE Data Bus DD7 Pull-Down Resistor ......................................................................... 64
10 HD Audio (bus-0, dev-20, fun-02) ........................................................................ 65
10.1 Enabling/Disabling HD Audio .................................................................................................... 65
10.2 HD Audio Interrupt Routing Table ............................................................................................. 65
10.3 Audio Port Configuration............................................................................................................. 65
Appendix A: Sample Codes for BIOS Workarounds........................................... 67
A1. Sample Code for SP5100 Erratum #11: “Enabling EHCI Dynamic Clock Gating May
Cause Bug Code 0xFE System Error”........................................................................................... 67
A2. Sample Code for SP5100 Erratum #23: “USB Wake on Connect/Disconnect with Low
Speed Devices”. ................................................................................................................................ 70
Appendix B: Revision History ................................................................................... 72
2012 Advanced Micro Devices, Inc.
AMD SP5100 Register Programming Requirements
TOC
Page 6
1 Introduction
1.1
About This Manual
This document lists the register settings required for the proper operation of the AMD SP5100
(previously referred to as SB700S). Current sampling of AMD SP5100 is with silicon revision A14
and A15, with the latter being the production part. This document covers settings for prior revision
A12 (used exclusively for SB7xx products) as a reference since the SP5100 CIMx is shared between
SP5100 and SB7xx. CIMx is a software module that helps OEMs to quickly integrate SP5100
support in their products. References to register settings for revision A12 apply only to SB7xx
products. References to register settings for Revision A14, A14 and above, A15, or All Revs apply to
SP5100.
Most of the register settings are mandatory and should be implemented as described in this
document. The document will be updated periodically with new or revised settings that are
determined during the qualification of the SP5100. Please refer to the latest updated document on
the AMD NDA website.
This document should be used in conjunction with the related AMD SP5100 BIOS Developer’s
Guide and the AMD SP5100 Register Reference Guide.
Note: In this document, changes/additions from the previous release are highlighted in red. Refer to
Appendix B: Revision History at the end of this document for a detailed revision history.
.
2012 Advanced Micro Devices, Inc.
AMD SP5100 Register Programming Requirements
Introduction
Page 7
1.2
AMD SP5100 Block Diagram
This section contains a block diagram for the SP5100. Figure 1 below shows the SP5100 internal
PCI devices and major functional blocks.
Alink Express II
AB
B-LINK
A-LINK
PORT 1
PORT 0
12 USB2.0 + 2
USB1.1 PORTS
B-LINK
SATA
Controller
Flash
Controller
USB:OHCI(x5)
(Not Supported)
Debug port
IDE
USB:EHCI(x2)
1 CHANNEL
6 PORTS(GEN-II)
FC interface
IDE interface
A-LINK
HD Audio
6 PCI SLOTS
SMBUS /ACPI
PCI Bridge
LPC
HD Link
LPC bus
LPC /FWH/SPI Rom interface
SPI bus
IMC_INT
RTC
X1/X2
BUS Controler
IMC
8051
SERIRQ#
INT# H:A
SIRQ
APIC/ PIC
INTERRUPT
controller
PICD[0]
RTC_IRQ#,
PIDE_INTRQ,
USB_IRQ#,
SATA_IRQ#,
AZ_IRQ#
GPIO
25MHz X1 / X2
PCIE_GFX_Clock
8250 TIMER
CPU_HT_HT
GPP_P/N (3:0)
CPU_NB_HT
Clock Gen
NB Disp Clock
USB Clock
SPEAKER
Flash Cont Clock
USB clock
SATA Clock
SIO Clock
SMI
ACPI / HW
Monitor
SMBUS
ASF
SMBUS
PM
PWRGOOD
GEVENT[7:0],SLPBUTTON
GPM [9:0]TEMPDEAD,
TEMPCAUT,
SHUTDOWN,DC_STOP#
SCIOUT,
SOFF#
LDTRST#
RESET#
Figure 1 SP5100 Internal PCI Devices and Major Functional Blocks
2012 Advanced Micro Devices, Inc.
AMD SP5100 Register Programming Requirements
Introduction
Page 8
1.3
Register Reference Information
Tables within this document contain information showing the applicable revision, recommended
settings, and comments associated with the register. Consider the following example:
ASIC Rev
All Revs SP5100
Register Settings
PM_IO 0x52[5:0] = 08h
Function/Comment
Recommended
Delay for S3/S4/S5 resume sequence
SATA
USB
SMBUS
PATA
AC97
HD AUDIO
RTC
ACPI
PM REG
X
A-LINK
I/O REG
XIOAPIC
LPC
PCI
For register details refer to
the sections check-marked in
the SP5100 Register
Reference Guide.
• ASIC Rev All Revs SP5100 = Applicable to all revisions of the SP5100
• ASIC Rev SP5100 A14 and above = Applicable to revisions A14 and A15 of the SP5100
• ASIC Rev SP5100 A14 = Applicable to revision A14 of the SP5100
• ASIC Rev SP5100 A12 = Not applicable, included for reference only (see section 1.1 “About
this Manual”)
• Register Settings Recommended register setting with the register name.
For more detailed information about the registers found within this document refer to the AMD
SP5100 Register Reference Guide. The applicable sections in the register reference guide where
the information can be found are marked with “x” in the tables in this document.
2012 Advanced Micro Devices, Inc.
AMD SP5100 Register Programming Requirements
Introduction
Page 9
2 ACPI/SMBUS Controller (bus-0, dev-20, fun-0)
2.1
Enabling Legacy Interrupt
ASIC Rev
All Revs SP5100
2.2
SATA
USB
RTC
ACPI
Register Settings
Smbus_PCI_config 0x62 [2] = 1
SMBUS
x
PM REG
All Revs SP5100
PATA
AC97
HD AUDIO
A-LINK
I/O REG
XIOAPIC
LPC
SATA
USB
RTC
ACPI
Register Settings
PCI
For register details refer to
the sections check-marked
in the SP5100 Register
Reference Guide
Function/Comment
Smbus_PCI_config 0xAC [4] = 0
SMBUS
x
PM REG
Set the bit to 0 to disable unblocked smi delivery from smi
command port so that smi from smi command port is gated
by EOS bit too.
PATA
AC97
HD AUDIO
A-LINK
I/O REG
XIOAPIC
LPC
PCI
For register details refer to
the sections check-marked
in the SP5100 Register
Reference Guide
WakeIO Base Address
ASIC Rev
All Revs SP5100
2.4
This bit enables legacy interrupt.
Unblocked SMI Command Port
ASIC Rev
2.3
Function/Comment
SATA
USB
RTC
ACPI
Register Settings
Function/Comment
This register is the I/O base address used to generate the Cstate wake event by the processor. The BIOS should
program this register with the I/O base address for the
SP5100. The base address in the CPU should also be
programmed. The CPU can use it to generate an I/O write to
the SB to wake the system from the C-state.
Smbus_PCI_config 0xF4 [15:0]
SMBUS
x
PM REG
PATA
AC97
HD AUDIO
A-LINK
I/O REG
XIOAPIC
LPC
PCI
For register details refer to
the sections check-marked
in the SP5100 Register
Reference Guide
C-State and VID/FID Change
ASIC Rev
All Revs SP5100
Register Settings
Function/Comment
BIOS should not report ARB_DIS to OS if
C3 pop-up is enabled.
With C3 pop-up, ARB_DIS should not be set or cleared by
software.
PM_IO 0x9A [5] = 1
For system with dual core CPU, set this bit to 1 to
automatically clear BM_STS when the C3 state is being
initiated.
2012 Advanced Micro Devices, Inc.
AMD SP5100 Register Programming Requirements
ACPI/SMBUS Controller (bus-0, dev-20, fun-0)
Page 10
ASIC Rev
Register Settings
Function/Comment
All Revs SP5100
PM_IO 0x9A [4] = 1
For system with dual core CPU, set this bit to 1 and
BM_STS will cause C3 to wakeup regardless of BM_RLD.
All Revs SP5100
PM_IO 0x8F [5] = 1
Ignores BM_STS_SET message from NB
All Revs SP5100 + PM_IO 0x8F [4] = 1
RS4x0 ASIC family
of NB
The SB will monitor BmReq# for C3 pop-up. The SB will
de-assert LDTSTP# when BmReq# is active.
All Revs SP5100 + PM_IO 0x8F [4] = 0
RS690 ASIC family
of NB
The SB will not monitor BmReq# for C3 pop-up. The SB
will de-assert LDTSTP# when AllowLdtStop is not active.
BmReq# activity is combined on AllowLdtStop in the
RS690 ASIC family of NB.
Stutter time: The following setting is for Stutter time (minimum time LDTSTP# is asserted before entering C3 state). There
are two settings that apply to different cases as listed below.
Case 1:
The following registers should be programmed only when Platform BIOS detects the CPUs listed below:
•
Family 10h with LS2 mode capability enabled:
Model=(8|9) && Stepping >= 1 || Model Ah OR for any CPU that has the HT link speed set to 200 MHz.
•
Family 15h with LS2 mode capability enabled:
Model= (00-0Fh) && C32r1 package || Model= (00-0Fh) && G34r1 package
Case 2:
Any CPU that does not meet the requirements set in Case 1.
PM_IO 0x8B = 0x0A
Case 1:
StutterTime = 0x0A for minimum LDTSTP# assertion
duration of 10 us in C3.
PM_IO 0x8B = 0x01
Case 2:
StutterTime = 01h for minimum LDTSTP# assertion
duration of 1us in C3.
All Revs SP5100
PM_IO 0x8A = 0x90
Bit[7] - Enable Stutter Mode for C3
Bits[6:4] - VidFidTime = 001b for LDTSTP# assertion
duration of 2us in VID/FID change.
All Revs SP5100
PM_IO 0x89 = 0x10
This provides 16us delay before the assertion of LDTSTP#
when C3 is entered. The delay will allow USB DMA to go
on in a continuous manner.
All Revs SP5100
PM_IO 0x88 = 0x10
LdtStartTime = 10h for minimum LDTSTP# de-assertion
duration of 16us in StutterMode. This is to guarantee that
the HT link has been safely reconnected before it can be
disconnected again. If C3 pop-up is enabled, the 16us also
serves as the minimum idle time before LDTSTP# can be
asserted again. This allows DMA to finish before the HT
link is disconnected.
All Revs SP5100
The following two registers should be programmed only if the following is true:
MTC1E is enabled but FID/VID is not enabled or MTC1E is enabled but FID/VID is not enabled
All Revs SP5100
PM_IO 0x9A [2] = 1
Enables pop-up for C3
For internal bus mastering or BmReq# from the NB, the SB
will de-assert LDTSTP# (pop-up) to allow DMA traffic, then
assert LDTSTP# again after some idle time.
PM_IO 0x7C [0] = 1
Set this bit to 1 to allow wakeup from C3 if break event
happens before LDTSTOP# assertion.
2012 Advanced Micro Devices, Inc.
AMD SP5100 Register Programming Requirements
ACPI/SMBUS Controller (bus-0, dev-20, fun-0)
Page 11
ASIC Rev
Register Settings
Function/Comment
All Revs SP5100
PM_IO 0x7C [1] = 1
Set this bit to 1 to allow pop-up request being latched
during the minimum LDTSTP# assertion time. Pop-up will
happen thereafter even if the request has gone.
All Revs SP5100
PM_IO 0x61 [2] = 0
This bit should be cleared to 0 if C3 pop-up is enabled. If this
bit is set to 1, the BmReq# input or internal bus mastering
will set BM_STS.
All Revs SP5100
PM_IO 0x42 [2] = 0
If this bit is set to 1, the SB will convert C2 into C3, i.e. LVL2
read is treated the same as LVL3 read by hardware. This
feature needs to be turned off because of the following
reason. Some USB applications require continuous DMA
transfer and are very sensitive to C3. The SB is configured
to allow USB to set BM_STS and cause immediate exit from
C3. When BM_STS is set the OS will issue C2 instead of
C3. If C2 is converted into C3, the exit will not happen until
the next interrupt because the OS does not set BM_RLD
before issuing C2 and BM_STS is not considered a break
event. Setting PM_IO 0x9A [4] = 1 can guarantee immediate
exit in this case. But then the C2 to C3 conversion does not
offer any power saving benefit. The feature is pending for
future exploration.
Note: C3 pop-up is recommended for all systems.
Quick reference: Settings for dual-core system:
PM_IO 0x9A [5] = 1
PM_IO 0x9A [4] = 1
PM_IO 0x9A [2] = 1 (default)
PM_IO 0x8F [5] = 1 (default)
PM_IO 0x8F [4] = (1 for SP5100 + RS4x0 NB; 0 for SP5100 + RS690 NB)
PM_IO 0x8B = 0x01 (default)
PM_IO 0x8A = 0x90 (default)
PM_IO 0x88 = 0x06 (default)
PM_IO 0x7C [0] = 1 (default)
PM_IO 0x7C [1] = 1 (default)
PM_IO 0x61 [2] = 0 (default)
PM_IO 0x42 [2] = 0 (default)
Quick reference: Settings for single-core system:
PM_IO 0x9A [5] = 0
PM_IO 0x9A [4] = 0
PM_IO 0x9A [2] = 1 (default)
PM_IO 0x8F [5] = 1 (default)
PM_IO 0x8F [4] = (1 for SP5100 + RS4x0 NB; 0 for SP5100 + RS690 NB)
PM_IO 0x8B = 0x01 (default)
PM_IO 0x8A = 0x90 (default)
PM_IO 0x88 = 0x06 (default)
PM_IO 0x7C [0] = 1 (default)
PM_IO 0x7C [1] = 1 (default)
PM_IO 0x61 [2] = 0 (default)
PM_IO 0x42 [2] = 0 (default)
SATA
USB
SMBUS
PATA
AC97
HD AUDIO
RTC
ACPI
PM REG
x
A-LINK
I/O REG
XIOAPIC
2012 Advanced Micro Devices, Inc.
AMD SP5100 Register Programming Requirements
LPC
PCI
For register details refer to
the sections check-marked
in the SP5100 Register
Reference Guide
ACPI/SMBUS Controller (bus-0, dev-20, fun-0)
Page 12
2.5
Enable C1e Stutter Timer and Limit Link Disconnect
to < 20 ms
ASIC Rev
Register Settings
Function/Comment
Stutter timer settings
The following settings will program the stutter timer settings. There are two different values that need to be applied based
on the condition listed below.
Case 1
The following registers should be programmed only when Platform BIOS detects the CPUs listed below:
•
Family 10h with LS2 mode capability enabled:
Model=6 && Stepping=2 II Model=(4I5|6) && Stepping >=3 || Model=(8|9) && Stepping >= 1 || Model
Ah
Case 2
Any CPU that does NOT meet the requirement in Case 1
SP5100 Rev A14
and above
PM_IO 0xCB [5] =1
AutoStutterTimerEn.
Set to 1 to enable.
PM_IO_0XCB[6] =1
Auto Stutter Timer time base select.
1 = millisecond
0 = 2 microseconds (set to 1 to select millisecond
increments)
SMBUS PCI config 0x5C[7] = 1
Monitor C3 state if set to 1.
Case 1
SMBUS PCI config 0x5C[22:16] = 14h
This register defines the timer value to trigger in 1
millisecond increments. (Set to 20 ms)
Case 2
SMBUS PCI config 0x5C[22:16] = 10h
This register defines the timer value to trigger in 1
millisecond increments. (Set to 16 ms)
SMBUS PCI config 0x5C should be restored after resume from S3 and S4.
SATA
USB
SMBUS
PATA
AC97
HD AUDIO
LPC
PCI
For register details, refer to
the sections check-marked
x
in the SP5100 Register
RTC
ACPI
PM REG
A-LINK
I/O REG
XIOAPIC
Reference Guide.
x
This part of logic borrows another function within SB to automatically stutter the C1e state when LDTSTOP# has been
asserted continuously for a period of time defined by SmartVolt time. Originally this logic was for monitoring system activity,
by setting AutoStutterTimerEn PMIO_CB[5], this logic becomes a timer to stutter the C1e.
2012 Advanced Micro Devices, Inc.
AMD SP5100 Register Programming Requirements
ACPI/SMBUS Controller (bus-0, dev-20, fun-0)
Page 13
2.6
MTC1e and FID VID Setting
ASIC Rev
Register Settings
Function/Comment
The following registers should be programmed only if FIDVID is enabled in conjunction with MTC1e
SP5100 All Revs
2.7
PM_IO 0x9A [2] = 0
K8CpopUp is disabled
PM_IO 0x7C 0] = 0
EnableBreak is disabled
SATA
USB
SMBUS
PATA
AC97
HD AUDIO
RTC
ACPI
PM_REG
x
A-LINK
I/O REG
XIOAPIC
LPC
PCI
For register details refer to
the sections check-marked
in the SP5100 Register
Reference Guide.
C1e Exit on Assertion of IDLE Exit# (for A15 Only)
ASIC Rev
Register Settings
Function/Comment
The following registers should be programmed to support the C1e exit when Sp5100 IDLE_EXIT# is connected to
BM_REQ# as break event
SP5100 rev A15.
SMBUS PCI 0x64[5]=1
Enable BMREQ# pin to the C state logic
PMIO_61[2]=1
Monitor BM_STS pin from NB and BM from SB
PMIO_9A[4]=1
BM_STS cause SB to wakeup from C3
PMIO_9A[5]=1
Clear BM_STS when system enters C3
SMBUS PCI 0x64[4]=0
Force IDLE_EXIT# to set BM_STS and wakes from C3.
SMBUS PCI 0x64[5]=1
SMBUS PCI config 0x64 should be restored after resume from S3 and S4.
2.8
SATA
USB
RTC
ACPI
SMBUS
x
PM_REG
x
PATA
AC97
HD AUDIO
A-LINK
I/O REG
XIOAPIC
LPC
PCI
For register details, refer to
the sections check-marked
in the SP5100 Register
Reference Guide.
Support for Entering C1e on HALT# Message (for A15 Only)
ASIC Rev
Register Settings
Function/Comment
The following registers should be programmed to support the CE1e with HALT# message.
SP5100 rev A15.
SATA
USB
RTC
ACPI
PMIO_BB[7]=1
Count HALT number and go into C3 automatically
PMIO_C9[4]=1
Monitor number of HALT messages
PMIO_C9[3:0]=1
number of HALTS to enter C1e
SMBUS
x
PM_REG
x
PATA
AC97
HD AUDIO
A-LINK
I/O REG
XIOAPIC
2012 Advanced Micro Devices, Inc.
AMD SP5100 Register Programming Requirements
LPC
PCI
For register details, refer to
the sections check-marked
in the SP5100 Register
Reference Guide.
ACPI/SMBUS Controller (bus-0, dev-20, fun-0)
Page 14
2.9
Enabling Non-Posted Memory Write
ASIC Rev
Register Settings
All Revs SP5100 AXINDC:0x10 [9] = 1
Function/Comment
Enables non-posted memory write.
Programming Sequence:
OUT AB_INDX,
OUT AB_DATA,
OUT AB_INDX,
IN AB_DATA,
OR TMP,
OUT AB_DATA,
0x00000030
0x00000010
0x00000034
TMP
0x00000200
TMP
//
//
//
//
//
//
Load AB_INDX with pointer to AX_INDXC
Write 0x10 to AX_INDXC
Load AB_INDX with pointer to AX_DATAC
Read PCIE_CTL register (AXINDC:0x10)
Set bit 9
Set PCIE_HT_NP_MEM_WRITE.
SATA
USB
SMBUS
PATA
AC97
HD AUDIO
RTC
ACPI
PM REG
A-LINK
X
I/O REG
XIOAPIC
LPC
PCI
For register details refer to
the sections check-marked
in the SP5100 Register
Reference Guide
2.10 Therm Trip Settings
ASIC Rev
Register Settings
All Revs SP5100 PM_IO 0x68 [3]
Function/Comment
0 = Disable the ThermTrip function on GEvent#2 pin.
1 = Enable the ThermTrip function on GEvent#2 pin.
PM_IO 0x55 [0] = 1 (default)
With this bit set to 1, the ThermTrip function once activated
will shutdown the system.
PM_IO 0x67 [6:5]
These two bits are used to set the polarity of the ThermTrip
and the TempCaut signals.
Default = 00 (this means that the signals are active low).
SATA
USB
SMBUS
PATA
AC97
HD AUDIO
RTC
ACPI
PM REG
X
A-LINK
I/O REG
XIOAPIC
LPC
PCI
For register details refer to
the sections check-marked
in the SP5100 Register
Reference Guide
2.11 Sx State Settings
ASIC Rev
Register Settings
All Revs SP5100 PM_IO 0x65 [7] = 0 (default)
Function/Comment
Use 8us clock for delays in the S-state resume timing
sequence.
PM_IO 0x68 [2] = 1 (default)
Delay the APIC interrupt to the CPU until the system has
fully resumed from the S-state.
Note: These 2 registers need to be set correctly for the S-state to work properly. Otherwise the system may hang during
resume from the S-state.
SATA
USB
SMBUS
PATA
AC97
HD AUDIO
RTC
ACPI
PM REG
X
A-LINK
I/O REG
XIOAPIC
2012 Advanced Micro Devices, Inc.
AMD SP5100 Register Programming Requirements
LPC
PCI
For register details refer to
the sections check-marked
in the SP5100 Register
Reference Guide
ACPI/SMBUS Controller (bus-0, dev-20, fun-0)
Page 15
2.12 Output Drive Strength Settings
ASIC Rev
Register Settings
Function/Comment
All Revs SP5100 Smbus_PCI_config 0xC0 [29:0]
Setting TBD
These register bits configure the drive strength of each
individual bus.
Refer to the AMD SP5100 Register Reference Guide,
SMBUS section describing the PCI config C0h for the
recommended driving strength values.
Note: For more detail please refer to the AMD SP5100 Register Reference Guide.
SATA
USB
RTC
ACPI
SMBUS
X
PM REG
PATA
AC97
HD AUDIO
A-LINK
I/O REG
XIOAPIC
LPC
PCI
For register details refer to
the sections check-marked
in the SP5100 Register
Reference Guide
2.13 SUS_STAT# Enhancement
ASIC Rev
Register Settings
Function/Comment
All Revs SP5100 PM_IO 0x7C[5]
1 = Enable SUS_STAT# enhancement.
0 = Disable SUS_STAT# enhancement.
If enabled SUS_STAT# assertion will be extended until
after the SB has fully resumed from the S3/4/5 state.
Note: This is a precautionary measure to suppress a glitch on the CKE pin for some early NB revisions on the P4 platform.
Enable it only if the NB requires.
SATA
USB
SMBUS
PATA
AC97
HD AUDIO
RTC
ACPI
PM REG
X
A-LINK
I/O REG
XIOAPIC
LPC
PCI
For register details refer to
the sections check-marked
in the SP5100 Register
Reference Guide
2.14 Interrupt Routing/Filtering
ASIC Rev
Register Settings
Function/Comment
Smbus_PCI_config 0x62 [1:0]
The filtering for IRQ1 and IRQ12 should be enabled only
when USB legacy support is enabled in internal USB host
controller side.
Smbus_PCI_config 0x67 [7]
The bit should be set to 1 only when USB legacy support is
enabled in internal USB host controller side.. By setting to 1
IRQ1/IRQ12 to PIC and IoApic controller comes from USB
legacy block.
Smbus_PCI_config 0x64 [13] = 1
Delay back to back interrupts to the CPU. The hardware will
delay an interrupt for approximately 500ns if there is a
pending interrupt. Some applications in PIC mode may not
be able to handle back to back interrupts in a short time
period. Enabling this bit will prevent the application from
encountering back to back interrupts.
All Revs SP5100
USB HC(bus0, dev 18, fun 0) MMio+160h
2012 Advanced Micro Devices, Inc.
AMD SP5100 Register Programming Requirements
Set to 0000_0000h when USB legacy support is disabled in
internal USB host controller side. SW has to make sure that
the USB Hc memory decoding is enabled in PCIi
configuration space command register.
ACPI/SMBUS Controller (bus-0, dev-20, fun-0)
Page 16
All Revs SP5100
Set to 0000_0000h when USB legacy support is disabled in
internal USB host controller side. SW has to make sure that
the USB Hc memory decoding is enabled in PCI
configuration space command register.
USB HC(bus0, dev 19, fun 0) MMio+160h
USB HC(bus0, dev 20, fun 5) MMio+160h
SATA
RTC
USB
X
ACPI
SMBUS
X
PM REG
Set to 0000_0000h when USB legacy support is disabled in
internal USB host controller side. SW has to make sure that
the USB Hc memory decoding is enabled in PCI
configuration space command register
PATA
AC97
HD AUDIO
A-LINK
I/O REG
XIOAPIC
LPC
PCI
For register details refer to
the sections check-marked
in the SP5100 Register
Reference Guide
2.15 IO Trap Settings
ASIC Rev
Register Settings
Function/Comment
All Revs SP5100 PM_IO 0x14 ~ 0x1B, 0xA0 ~ 0xA7
Programmable address ranges for IO trap.
PM_IO 0x1C ~ 0x1D, 0xA8 ~ 0xA9
IO trap enable/status registers.
1.
2.
ABCFG 0x10090 [16] = 1 ensures the SMI# message to be
sent before the IO command is completed.
ABCFG 0x10090 [16] = 1
PM_IO 0x14 ~ 0x1D or 0xA0 ~ 0xA9
SATA
USB
SMBUS
PATA
AC97
HD AUDIO
RTC
ACPI
PM REG
X
A-LINK
X
I/O REG
XIOAPIC
LPC
PCI
For register details refer to
the sections check-marked
in the SP5100 Register
Reference Guide
2.16 Enabling ACPI Registers
ASIC Rev
Register Settings
Function/Comment
All Revs SP5100 1. Assign the IO base address for the
following ACPI registers:
- AcpiPm1EvtBlk = PM_IO 0x20, 0x21
- AcpiPm1CntBlk = PM_IO 0x22, 0x23
- AcpiPmTmrBlk = PM_IO 0x24, 0x25
- CpuControl
= PM_IO 0x26, 0x27
- AcpiGpe0Blk
= PM_IO 0x28, 0x29
- AcpiSmiCmd
= PM_IO 0x2A, 0x2B
- AcpiPmaCntBlk = PM_IO 0x2C, 0x2D
2. Set AcpiDecodeEnable
- PM_IO 0x0E[3] = 1
The BIOS needs to assign the IO base address for each of
the ACPI registers before enabling the ACPI decode. The
IO base addresses are defined in PM_IO 0x20 ~ 0x2F
registers.
Note 1: The PM_IO 0x20 ~ 0x2F registers are undefined
upon the first system power up and may therefore contain
random values. If the BIOS enables the ACPI decode
without assigning the proper IO base addresses for the
ACPI registers, the SB may decode incorrect IO addresses
and cause unexpected system behavior.
Note 2: The PM_IO 0x2E/2F registers must be
programmed with a valid I/O address. The recommended
address is using the AcpiSmiCmd + 8. Leaving this register
to a default of 0 will cause a conflict with legacy DMA.
SATA
USB
SMBUS
PATA
AC97
HD AUDIO
RTC
ACPI
PM REG
X
A-LINK
I/O REG
XIOAPIC
2012 Advanced Micro Devices, Inc.
AMD SP5100 Register Programming Requirements
LPC
PCI
For register details refer to
the sections check-marked
in the SP5100 Register
Reference Guide
ACPI/SMBUS Controller (bus-0, dev-20, fun-0)
Page 17
2.17 Legacy DMA Prefetch Enhancement
ASIC Rev
Register Settings
Function/Comment
All Revs SP5100 Smbus_PCI_config 0x43 [0] = 1 (only when Enables legacy DMA prefetch enhancement for channel 0,
the system is non-DOS mode)
1, 2, and 3. This bit should be set to improve DMA out (eg
memory-to-floppy disk) performance.
Note: This bit should only be enabled in the ACPI method
(called by the OS). This ensures that it is enabled only
when the system is in Window mode. Under DOS mode,
this feature may not work properly and may cause the
floppy to malfunction.
Smbus_PCI_config 0x41 [7] = 1
Lpc_PCI_config 0x78 [0] = 0
SATA
USB
RTC
ACPI
SMBUS
X
PM REG
Set these bits to make LPC DMA work properly.
PATA
AC97
HD AUDIO
A-LINK
I/O REG
XIOAPIC
LPC
PCI
For register details refer to
the sections check-marked
in the SP5100 Register
Reference Guide
2.18 USB Set BM_STS
ASIC Rev
Register Settings
Function/Comment
For balanced power saving and USB performance, allow
USB DMA to cause pop-up. Other register settings for C
state should be followed for the system to work properly.
All Revs SP5100 PM_IO 0x66 [6] = 0
Note: Refer to USB register settings section for the corresponding USB register settings that are required to be
programmed when the above registers are programmed. For the AMD platform, PM_IO 0x66 [6], and register settings in
the USB register settings section should be programmed.
SATA
USB
SMBUS
PATA
AC97
HD AUDIO
RTC
ACPI
PM REG
x
A-LINK
I/O REG
XIOAPIC
LPC
PCI
For register details refer to
the sections check-marked
in the SP5100 Register
Reference Guide
2.19 Enabling Spread Spectrum
ASIC Rev
Register Settings
Function/Comment
Enables spread spectrum on PCI clocks with -0.5%
spread. In external clock mode, the internal SS when
enabled will down spread the PCI clocks. The 100 MHz
PCIe clock SB_SRC from the external clock generator
should not have spread spectrum enabled if the internal
spread is enabled. Refer to PA_SP5100AGx for more
information on enabling the spread spectrum.
All Revs SP5100 PM_IO 0x42 [7] = 1
SATA
USB
SMBUS
PATA
AC97
HD AUDIO
RTC
ACPI
PM REG
x
A-LINK
I/O REG
XIOAPIC
2012 Advanced Micro Devices, Inc.
AMD SP5100 Register Programming Requirements
LPC
PCI
For register details refer to
the sections check-marked
in the SP5100 Register
Reference Guide
ACPI/SMBUS Controller (bus-0, dev-20, fun-0)
Page 18
2.20 PCIe Native Mode
ASIC Rev
Register Settings
Function/Comment
Set to 1 to enable PCIe native mode.
If PCIe is in Native mode: set the bit to 1.
If PCIe is not in Native mode: set the bit to 0.
All Revs SP5100 PM_IO 0x55 [3]
PM_IO 0x10 [6]
Set to 1 to make PCIE_WAK_DIS visible in ACPI Pm1a
register group.
If PCIe is in Native mode:
set the bit to 1.
If PCIe is not in Native mode: set the bit to 0.
PM_IO 0x55 [4]
Set to 0 to enable PCIE_WAK_DIS/PCIE_WAK_STS
function.
If PCIe is in Native mode: set the bit to 0.
If PCIe is not in Native mode: set the bit to 1.
PM_IO 0x55 [5] = 1
Set to 1 to force the non-generation of SCI when seeing
PCIe wake event. Set the bit to 1 all the time.
PM_IO 0x84 [0] = 0
PM_IO 0x84 [1] = 0
Generate SCI interrupt in PCIe legacy mode when wake#
is asserted.
PM_IO 0xD7 [6] = 1
Mask off the input of PCIE_Wak_Sts if PCIE_WAK_DIS is
1. Set the bit to 1 all the time.
PM_IO 0xD7 [1] = 1
Routes PME_message from NB to the input of
PCIE_Wak_Sts. Set the bit to 1 all the time.
Suggested settings:
WinXP
0
0
1
1
1
0
1
1
PM_IO 0x55[3]
PM_IO 0x10[6]
PM_IO 0x55[4]
PM_IO 0x55[5]
PM_IO 0x84[0]
PM_IO 0x84[1]
PM_IO 0xD7[6]
PM_IO 0xD7[7]
Vista (Legacy mode)
0
1
0
1
1
0
1
1
SATA
USB
SMBUS
PATA
AC97
HD AUDIO
RTC
ACPI
PM REG
X
A-LINK
I/O REG
XIOAPIC
LPC
PCI
Vista (Native mode)
1
1
0
1
1
0
1
1
For register details refer to
the sections check-marked
in the SP5100 Register
Reference Guide
2.21 Hardware Monitor
ASIC Rev
Register Settings
All Revs SP5100 PM_IO 0xD7 [7] = 7
Function/Comment
Set only if Hardware monitor is used for temperature
reading
SATA
USB
SMBUS
PATA
AC97
HD AUDIO
RTC
ACPI
PM REG
X
A-LINK
I/O REG
XIOAPIC
2012 Advanced Micro Devices, Inc.
AMD SP5100 Register Programming Requirements
LPC
PCI
For register details refer to
the sections check-marked
in the SP5100 Register
Reference Guide
ACPI/SMBUS Controller (bus-0, dev-20, fun-0)
Page 19
2.22 Cir Interrupt Config
ASIC Rev
Register Settings
All Revs SP5100 Smbus_PCI_config 0xE1[6]
SATA
USB
RTC
ACPI
SMBUS
X
PM REG
Function/Comment
Set to 1 to treat Cir interrupt as level signal; otherwise it
is edge.trigger:
PATA
AC97
HD AUDIO
A-LINK
I/O REG
XIOAPIC
LPC
PCI
For register details refer to
the sections check-marked
in the SP5100 Register
Reference Guide
2.23 SMBUS PCI Config
ASIC Rev
Register Settings
Function/Comment
A11 and A12
Smbus_PCI_config 0xE1[0] = 1
Forces Smbus controller to be enabled all the time, even if
Io/Mem decoding bit is set to 0.
A11 and A12
Smbus_PCI_config 0xE1[1]
Mmio decoding required setting
All Revs SP5100 Smbus_PCI_config 0xE1[2]
SATA
USB
RTC
ACPI
Set to 1 to enable Io port 60h read/write SMi trapping and
Io port 64h write Smi trapping.
Smbus_PCI_config 0xE1[3] = 1
Required for INTA message decoding.
Smbus_PCI_config 0xE1[4] = 1
Smbus0 busy bit enhancement
SMBUS
X
PM REG
PATA
AC97
HD AUDIO
A-LINK
I/O REG
XIOAPIC
LPC
PCI
For register details refer to
the sections check-marked
in the SP5100 Register
Reference Guide
2.24 IMC Access Control
ASIC Rev
Register Settings
All Revs SP5100 Smbus_PCI_config 0xE1[7] = 1
Smbus_PCI_config 0xAF[1] = 0
Function/Comment
Required for proper function of the IMC shared access.
The following register should only be programmed if IMC is enabled
Smbus_PCI_config 0xE1[5] = 1
SATA
USB
RTC
ACPI
SMBUS
X
PM REG
Required for proper function of the IMC shared access.
PATA
AC97
HD AUDIO
A-LINK
I/O REG
XIOAPIC
2012 Advanced Micro Devices, Inc.
AMD SP5100 Register Programming Requirements
LPC
PCI
For register details refer to
the sections check-marked
in the SP5100 Register
Reference Guide
ACPI/SMBUS Controller (bus-0, dev-20, fun-0)
Page 20
2.25 CPU Reset
ASIC Rev
Register Settings
Function/Comment
All Revs SP5100 PM_IO 0xB2[2] = 1
SATA
USB
RTC
ACPI
SMBUS
X
PM REG
Enables the CPU Reset timing option defined in PM
register D5[1:0]. Required only if the default timing needs
to be changed.
PATA
AC97
HD AUDIO
A-LINK
I/O REG
XIOAPIC
LPC
PCI
For register details refer to
the sections check-marked
in the SP5100 Register
Reference Guide
2.26 Disabling Legacy USB Fast SMI#
ASIC Rev
Register Settings
Function/Comment
All Revs SP5100 Smbus_PCI_config 0x62 [5] = 1
SATA
USB
RTC
ACPI
SMBUS
x
PM REG
Legacy USB can request SMI# to be sent out early before
IO completion. Some applications may have problems with
this feature. The BIOS should set this bit to 1 to disable the
feature.
PATA
AC97
HD AUDIO
A-LINK
I/O REG
XIOAPIC
LPC
PCI
For register details refer to
the sections check-marked
in the SP5100 Register
Reference Guide
2.27 SMBUS1 Programming Sequence
ASF SMBUS 1 interface incorporates ASF and SMBUS1 controllers. ASF features (capability of using
ACPI services by ASF master) are not supported on SP5100. However, the SMBUS1 controller can be
used as a generic SMBUS interface with SMBUS1 controller operating as master to communicate to
SMBUS slave devices that need to be on S5 power domain. The ASF slave controller in SP5100 is
disabled but some registers belonging to ASF controller will need to be programmed to support SMBUS1
controller in Master mode.
•
Step 1: Set the base address of ASF IO space by programming bits [15:4] of Sm cfg space reg
58h:
ASFSMbusIoBase- RW - 16 bits - [PCI_Reg: 58h]
Field Name
ASFSMBusEnable
Reserved
ASFSMBase
•
Bits
Default
0
0h
3:1
15:4
000b
FFFh
Description
0: Disable ASF controller
1: Enable ASF controller
ASF SM bus controller Io base address
Step 2: Enable the ASF controller by programming bit[0] of Sm cfg space reg 58h:
ASFSMbusIoBase- RW - 16 bits - [PCI_Reg: 58h]
Field Name
ASFSMBusEnable
Bits
Default
0
0h
Description
0: Disable ASF controller
1: Enable ASF controller
2012 Advanced Micro Devices, Inc.
AMD SP5100 Register Programming Requirements
ACPI/SMBUS Controller (bus-0, dev-20, fun-0)
Page 21
ASFSMbusIoBase- RW - 16 bits - [PCI_Reg: 58h]
Field Name
Reserved
ASFSMBase
•
Bits
Default
3:1
15:4
000b
FFFh
Description
ASF SM bus controller Io base address
Step 3: Disable Legacy Sensor support by programming bit[6] of ASF I/O 0Dh to 1
SlaveMisc- RW - 8 bits - [ASF_IO: 0Dh]
Field Name
Bits
Default
SlavePECError
0
0b
SlaveBusCollision
1
0b
SlaveDevError
2
0b
WrongSP
3
0b
Reserved
SuspendSlave
4
5
0b
0b
KillSlave
6
0b
LegacySensorEn
7
0b
•
Description
RO
0: No PEC error
1: PEC error
RO
0: No BusCollision
1: BusCollision happens
RO
0: Expected response
1: Unexpected response
RO
0: No SP error
1: No SP when turn to read
RW
Write 1 to Suspend (stop) ASF Slave state machine
RW
Write 1 to reset Slave ASF Slave state machine
RW
0: Disable Legacy Sensor
1: Enable Legacy Sensor
Step 4: Enable PEC if SMBUS device supports PEC:
HostControl – RW - 8 bits - [ASF_IO: 02h]
Field Name
Bits
Default
Reserved
KillHost
0
1
0b
0b
Protocol
4:2
000b
PECAppend
5
0b
Start
6
0b
PECEnable
7
0b
Description
0: Enable SM master
1: Reset SM master
000: Quick
001: Byte
010: Byte Data
011: Word Data
100: Process call
101: Block
0: No PEC append
1: Automatic PEC append. ASF HC calculates CRC code and append
to the tail of the data packets.
WO:
0: Always read 0 on reads
1: Writing 1 to initiate the command
0: PEC disable
1: PEC enable, enable CRC checking when ASF HC presents
as SM master and SM slave.
2012 Advanced Micro Devices, Inc.
AMD SP5100 Register Programming Requirements
ACPI/SMBUS Controller (bus-0, dev-20, fun-0)
Page 22
2.28 ACPI System Clock Setting
ASIC Rev
Register Settings
Function/Comment
All Revs SP5100 PMIO 0x53 [6] = 1
Enables the internally generated 14.318Mhz clock to the
ACPI logic.
SATA
USB
SMBUS
PATA
AC97
HD AUDIO
RTC
ACPI
PM REG
x
A-LINK
I/O REG
XIOAPIC
LPC
PCI
For register details refer to
the sections check-marked
in the SP5100 Register
Reference Guide
2.29 Integrated Pull-up and Pull-down Settings
ASIC Rev
Register Settings
Function/Comment
All Revs SP5100 PMIO2_F3, PMIO2_F4, PMIO2_F5,
PMIO2_F6, PMIO2_F7, PMIO2_F8
SATA
USB
RTC
ACPI
SMBUS
PM2
REG
x
The BIOS needs to set pull-up/down settings for
GEVENT/GPM platform specifically. These pins have
integrated pull-up/down enabled by default and they are
powered by the S5 power. If they are to be connected to a
device that will be powered down during sleep state, the
BIOS should disable the pull-up/down and use external
pull-up/down to avoid leakage.
PATA
AC97
HD AUDIO
A-LINK
I/O REG
XIOAPIC
LPC
PCI
For register details refer to
the sections check-marked
in the SP5100 Register
Reference Guide
2.30 Revision ID
ASIC Rev
SP5100 A12
Register Settings
Function/Comment
Smbus_PCI_config 0x08
PMIO_53[6]
Smbus_PCI_config 0x40 [0]
Notes: A12 revision ID – 0x3A. Smbus PCI
config space 0x08 will show 3Ah after BIOS
is initialized.
In order to determine and set the correct revision ID for
SP5100, BIOS needs to perform the following sequence:
(1) During early post, read Smbus_PCI_config 0x08 and
PMIO_53[6] to determine if the ASIC is A11 or A12.
The ASIC is A11 if the return values are 39h and 0b
respectively. If Smbus_PCI_config 0x08 returns 3Ah, or
Smbus_PCI_config 0x08 is 39h and PMIO_53[6] is 1b,
then the ASIC is A12.
(2) If Smbus_PCI_config 0x08 is 39h and PMIO_53[6] is
1b, BIOS should write to Smbus_PCI_config, 0x40[0] = 1,
follow by writing to Smbus_PCI_config, 0x08 with a value
of 3Ah. Afterward, BIOS should clear Smbus_PCI_config,
0x40[0] back to 0.
SP5100 A14
Smbus_PCI_Config 0x08
This register will show 0x3C as revision ID for SP5100 A14.
SP5100 A15
Smbus_PCI_Config 0x08
This register will show 0x3D as revision ID for SP5100 A15.
SATA
USB
RTC
ACPI
SMBUS
x
PM_REG
x
PATA
AC97
HD AUDIO
A-LINK
I/O REG
XIOAPIC
2012 Advanced Micro Devices, Inc.
AMD SP5100 Register Programming Requirements
LPC
PCI
For register details refer to
the sections check-marked
in the SP5100 Register
Reference Guide
ACPI/SMBUS Controller (bus-0, dev-20, fun-0)
Page 23
2.31 Alternate Pin for 14 MHz Clock Input
ASIC Rev
Register Settings
Function/Comment
The following change is required for SP5100 revision A14 and above and if the 14 MHz clock is connected to the SB on to
25M_48M_66M_OSC. This reference clock is required to resolve the revision A12 Errata item #5 in hardware instead of
using the BIOS workaround. If external 14 MHz clock is not used on SP5100 rev A14 and above, then the BIOS
workaround described in erratum #5 should be implemented.
SP5100 A14 and PMIO 0xD4[6] = 1
above
Program this register to ‘1’ if the system supports 14.318
MHz reference clock connected to 25M_48M_66M_OSC.
This reference clock is required to resolve the revision A12
Errata item #5 in hardware instead of using the BIOS
workaround.
This register bit is not supported on A12 and should not be
programmed by the BIOS.
SATA
USB
SMBUS
PATA
AC97
HD AUDIO
RTC
ACPI
PM_REG
x
A-LINK
I/O REG
XIOAPIC
LPC
PCI
For register details, refer to
the sections check-marked
in the SP5100 Register
Reference Guide.
2.32 Gevent5 as GPIO
ASIC Rev
Register Settings
SP5100 A14 and PMIO 0xD7[2] = 1
above
Function/Comment
This bit should be programmed if the Gevent5 needs to be
used as for GPIO function on revision A14.
Revision A12 does not support GPIO function on the
GEVENT pin.
Programming this register for A14 will make this pin on
A14 function as GPIO. (Note that the GEVENT pin still
needs to be programmed for GPIO as any other pins. The
programming of this bit is in addition to the normal
programming procedure of GPIO/ GEVENT pins.)
If this bit is cleared, the function of this pin is same as in
revision A12. The power up default of this bit is ‘0’.
0 ( default ) : Disable
1 : Enable
This register bit is not supported on A12 and should not be
programmed by the BIOS for A12.
SATA
USB
SMBUS
PATA
AC97
HD AUDIO
RTC
ACPI
PM_REG
x
A-LINK
I/O REG
XIOAPIC
LPC
PCI
For register details, refer to
the sections check-marked
in the SP5100 Register
Reference Guide.
These registers should be programmed by Platform System BIOS if Gevent5 functionality is required.
2012 Advanced Micro Devices, Inc.
AMD SP5100 Register Programming Requirements
ACPI/SMBUS Controller (bus-0, dev-20, fun-0)
Page 24
2.33 SMBUS Block Write Filtering
ASIC Rev
Register Settings
SP5100 A14 and Smbus_PCI_config 0x38 [7]=0
above
Function/Comment
Enable SMBUS filtering circuit. Setting this bit to 0 to
enable SMBUS filtering (1194).
THIS FEATURE WILL RESOLVE THE ISSUE DESCRIBED IN
REVISION A12 ERRATA ITEM # 13.
SATA
USB
RTC
ACPI
SMBUS
x
PM_REG
PATA
AC97
HD AUDIO
A-LINK
I/O REG
XIOAPIC
LPC
PCI
For register details, refer to
the sections check-marked
in the SP5100 Register
Reference Guide.
2.34 SMBUS Sequence
The following programming sequence should be followed when reading or writing to the
SMBUS 0:
1. read HostBusy bit
2. if not zero
if time out (recommended time out == 1ms or greater)
set kill bit
go back step 1.
else
go to step 3
3. read SlaveBusy
4. if not zero
if time out
set reset bit
go back step 3.
else
go to step 5
5. clear HostStatus register, program Slave Address register/Command register/ Data0/Data1/Data
6. read HostControl register
7. write HostControl register to start the transaction.
8. wait HostBusy bit to be 1
9. wait HostBusy bit to be 0
10.wait one SMBUS clock period.
11. wait HostBusy bit to 0.
2.35 Software Clock Throttle Period
ASIC Rev
Register Settings
All Revs SP5100 PMIO 0x68[7:6] = 10
2012 Advanced Micro Devices, Inc.
AMD SP5100 Register Programming Requirements
Function/Comment
Set AcpiThrotPeriod field in MiscEnable68 to 244 µS
(Hardware default is set to 15 µS)
ACPI/SMBUS Controller (bus-0, dev-20, fun-0)
Page 25
SATA
USB
SMBUS
PATA
AC97
HD AUDIO
RTC
ACPI
PM_REG
X
A-LINK
I/O REG
XIOAPIC
LPC
PCI
For register details, refer to
the sections check-marked
in the SP5100 Register
Reference Guide.
2.36 Unconditional Shutdown
ASIC Rev
SP5100 A15
Register Settings
Smbus_PCI_config 0x38[12] = 1
Function/Comment
Enable the enhancement for unconditional shutdown
Set sm cfg 43 bit 3 to 0 first before programming this bit,
then set 43h bit 3 back to 1 after programming.
SATA
USB
RTC
ACPI
SMBUS
x
PM_REG
PATA
AC97
HD AUDIO
A-LINK
I/O REG
XIOAPIC
LPC
PCI
For register details, refer to
the sections check-marked
in the SP5100 Register
Reference Guide.
2.37 Watchdog Timer Resolution
The register below should be programmed by SW before WDT is programmed.
ASIC Rev
Register Settings
All Revs SP5100 PMIO 0x69[0] = 0
Function/Comment
Enable WDT function (0: Enable; 1: Disable)
PMIO 0x69[2:1] = 01
00: Set resolution for 32 us
01: Set resolution for 10ms
10: Set resolution for 100ms
11: Set resolution for 1s
10ms resolution is recommended.
SATA
USB
SMBUS
PATA
AC97
HD AUDIO
RTC
ACPI
PM_REG
x
A-LINK
I/O REG
XIOAPIC
2012 Advanced Micro Devices, Inc.
AMD SP5100 Register Programming Requirements
LPC
PCI
For register details, refer to
the sections check-marked
in the SP5100 Register
Reference Guide.
ACPI/SMBUS Controller (bus-0, dev-20, fun-0)
Page 26
2.38 Supporting IDLE_EXIT# from CPU
ASIC Rev
Register Settings
Function/Comment
The following register should be programmed to support IDLE_EXIT# from CPU to wake C1e state
SP5100 revision SMBUS PCI 0x64[5]=1
A14 and above PMIO 0x61[2]=1
PMIO_0x9A[5:4]=11
SATA
USB
RTC
ACPI
SMBUS
x
PM_REG
x
Enable BM_STS# pin
Enable BM_STS# to break C1e
Enable automatic BM_STS clearing upon C1e entry
PATA
AC97
HD AUDIO
A-LINK
I/O REG
XIOAPIC
LPC
PCI
For register details, refer to
the sections check-marked
in the SP5100 Register
Reference Guide.
This part of logic borrows the existing legacy ACPI BM_STS and BM_RLD bits as a mechanism to break out from C1e
under a non-OS controlled C3 state. Under this scheme, the logic will automatically clears the BM_STS bit whenever it
enters C1e state. Whenever BM_REQ#/IDLE_EXIT# is detected, it will cause the BM_STS bit to be set and thereby
causing the C state logic to exit. BIOS should clear the BM_STS bit on every post.
2.39 Supporting HALT Message to Generate C1e
ASIC Rev
Register Settings
Function/Comment
The following register should be programmed to support HALT message to C1e function
SP5100 A14 and PMIO 0xBB[7]=1
PMIO_0xC9[4]=1
above
PMIO 0xC9[3:0] = Number of Halt Enter
messages to trigger C1e
Enable HALT message to C1e function
Enable counting of HALT message
Setting number of HALT messages to generate C1e
SATA
USB
SMBUS
PATA
AC97
HD AUDIO
RTC
ACPI
PM_REG
x
A-LINK
I/O REG
XIOAPIC
LPC
PCI
For register details, refer to
the sections check-marked
in the SP5100 Register
Reference Guide.
This part of logic basically counts the number of HALT_ENTER messages. When it has received the number of
HALT_ENTER messages equal to NumOfHalt (PMIO_C9[3:0] ), it will generate an internal C1e command to the C state
logic.
This count will increment when it sees HALT_ENTER and decrement when it sees HALT_EXIT. If it receives a
HALT_EXIT message after it has generated the C1e command, it will treat the HALT_EXIT as a break event.
2012 Advanced Micro Devices, Inc.
AMD SP5100 Register Programming Requirements
ACPI/SMBUS Controller (bus-0, dev-20, fun-0)
Page 27
2.40 LDT_PWRGD De-assertion with SLP_S3#
ASIC Rev
SP5100 A15
SATA
USB
RTC
ACPI
Register Settings
Smbus_PCI_config 0x41 [3]=1
SMBUS
x
PM_REG
Function/Comment
Set this bit to 1 to force LDT_PWRGD to be de-asserted at
the same time as SLP_S3#.
PATA
AC97
HD AUDIO
A-LINK
I/O REG
XIOAPIC
LPC
PCI
For register details, refer to
the sections check-marked
in the SP5100 Register
Reference Guide.
2.41 Programmable Interrupt Controller Arbitration
ASIC Rev
Register Settings
All Revs SP5100 Smbus_PCI_config 0xAE [6]=1
SATA
USB
RTC
ACPI
SMBUS
x
PM_REG
Function/Comment
Set this bit to 1 to allow the arbiter proper operation in
cases where both the PIC and APIC are enabled.
PATA
AC97
HD AUDIO
A-LINK
I/O REG
XIOAPIC
LPC
PCI
For register details, refer to
the sections check-marked
in the SP5100 Register
Reference Guide.
2.42 HPET MSI Setting
ASIC Rev
Register Settings
All Revs SP5100 Smbus_PCI_config 0x40 [31:29]= 000b
SATA
USB
RTC
ACPI
SMBUS
x
PM_REG
Function/Comment
Program these register bits ONLY if the following are true
in the platform configuration:
1. Legacy Floppy Drive interface supported
2. Legacy FIR device supported
PATA
AC97
HD AUDIO
A-LINK
I/O REG
XIOAPIC
2012 Advanced Micro Devices, Inc.
AMD SP5100 Register Programming Requirements
LPC
PCI
For register details, refer to
the sections check-marked
in the SP5100 Register
Reference Guide.
ACPI/SMBUS Controller (bus-0, dev-20, fun-0)
Page 28
2.43 SMAF Matching Setting
ASIC Rev
Register Settings
All Revs SP5100 Smbus_PCI_config 0x60 [22] = 1b
SATA
USB
RTC
ACPI
SMBUS
x
PM_REG
Function/Comment
This bit is required to be set to cover a corner case of
concurrent throttling and C1e
PATA
AC97
HD AUDIO
A-LINK
I/O REG
XIOAPIC
2012 Advanced Micro Devices, Inc.
AMD SP5100 Register Programming Requirements
LPC
PCI
For register details, refer to
the sections check-marked
in the SP5100 Register
Reference Guide.
ACPI/SMBUS Controller (bus-0, dev-20, fun-0)
Page 29
3 LPC Controller (bus-0, dev-20, fun-3)
3.1
IO / Mem Decoding
ASIC Rev
All Revs SP5100
3.2
Register Settings
Lpc_PCI_config 0xBB[7] = 1
Lpc_PCI_config 0xBB[6] = 1
Lpc_PCI_config 0xBB[3] = 1
Function/Comment
These bits are required to be set for LPC PCI slave
interface.
SATA
USB
SMBUS
PATA
AC97
HD AUDIO
RTC
ACPI
PM REG
A-LINK
I/O REG
XIOAPIC
LPC
X
PCI
For register details refer to
the sections check-marked
in the SP5100 Register
Reference Guide
SPI Bus
ASIC Rev
All Revs SP5100
Register Settings
Function/Comment
Lpc_PCI_config 0xBB[5] = 1
Set to 1 to allow SPI Op code to execute even though it is
now strapped as LPC Rom. Some BIOS code may want to
send SPI opcodes to check if SMI Rom is present. If the
system configuration is set for LPC, then the SPI opcode will
not be passed to SPI if this bit is not set.
Spi_mmio 0x00[28] = 1
Allows the software to read the status number of the SPI
read cycles completed – 1. Eliminates the last count.
Lpc_PCI_config 0xBB[0] = 1
Set to 1 to improve SPI read performance.
The bit should be set after programming the I/O modes and
SPI speed.
SATA
USB
SMBUS
PATA
AC97
HD AUDIO
RTC
ACPI
PM REG
A-LINK
I/O REG
XIOAPIC
2012 Advanced Micro Devices, Inc.
AMD SP5100 Register Programming Requirements
LPC
X
PCI
For register details refer to
the sections check-marked
in the SP5100 Register
Reference Guide
LPC Controller (bus-0, dev-20, fun-3)
Page 30
4 A-Link Express Settings - Indirect I/O Access
4.1
Defining AB_REG_BAR
ASIC Rev
Register Settings
All Revs SP5100 Smbus_PCI_config 0xF0 [31:0] =
AB_REG_BAR
4.2
SATA
USB
RTC
ACPI
SMBUS
X
PM REG
Function/Comment
Defines the AB I/O base address.
Refer to AMD SP5100 Register Reference Guide, chapter 4:
A-Link Express/A-Link Bridge Registers for more
information.
PATA
AC97
HD AUDIO
A-LINK
I/O REG
XIOAPIC
LPC
PCI
For register details refer to
the sections check-marked
in the SP5100 Register
Reference Guide
Clearing AB_INDX
The programming procedure for the ABCFG registers, as specified in the register reference
guide, is to first load AB_INDX with a register’s RegSpace and RegAddr; and then access the
specified register through AB_DATA. The example below demonstrates how to read
ABCFG:10058h:
OUT AB_INDX, 0xC0010058
IN AB_DATA, TMP
// Set AB_INDX RegSpace=11 RegAddr=0x10058
For certain revisions of the chip, the ABCFG registers, with an address of 0x100NN (where ‘N’ is
any hexadecimal number), require an extra programming step. This required step is defined in
the following table:
ASIC Rev
Register Settings
All Revs SP5100 AB_INDX = 0x00000000
Function/Comment
Clears AB_INDX after reading or writing an ABCFG
register with an address 0x100NN.
Example Programming Sequence:
OUT AB_INDX, 0xC00100NN
IN AB_DATA, TMP
OUT AB_INDX, 0x00000000
// Load AB_INDX with pointer to ABCFG:0x100NN
// Read ABCFG 0x100NN
// Clear AB_INDX
SATA
USB
SMBUS
PATA
AC97
HD AUDIO
RTC
ACPI
PM REG
A-LINK
X
I/O REG
XIOAPIC
2012 Advanced Micro Devices, Inc.
AMD SP5100 Register Programming Requirements
LPC
PCI
For register details refer to
the sections check-marked
in the SP5100 Register
Reference Guide
A-Link Express Settings - Indirect I/O Access
Page 31
4.3
Enabling Upstream DMA Access
ASIC Rev
Register Settings
All Revs SP5100 AXCFG: 0x04 [2] = 1
Function/Comment
Enables the SP5100 to issue memory read/write requests in
the upstream direction.
Programming Sequence:
OUT
IN
OR
OUT
4.4
AB_INDX,
AB_DATA,
TMP,
AB_DATA,
0x80000004
TMP
0x00000004
TMP
//
//
//
//
Load AB_INDX with pointer to AXCFG:0x04
Read COMMAND register (AXCFG:0x04)
Set bit 4
Set BUS_MASTER_EN
SATA
USB
SMBUS
PATA
AC97
HD AUDIO
RTC
ACPI
PM REG
A-LINK
X
I/O REG
XIOAPIC
LPC
PCI
For register details refer to
the sections check-marked
in the SP5100 Register
Reference Guide
IDE/PCIB Prefetch Settings
ASIC Rev
Register Settings
All Revs SP5100 IDE prefetch
ABCFG 0x10060 [17] = 1
ABCFG 0x10064 [17] = 1
Function/Comment
The settings on AB control the IDE and PCIB prefetch. For
all revisions the pre-fetch needs to be enabled for
performance enhancement.
PCIB prefetch
ABCFG 0x10060 [20] = 1
ABCFG 0x10064 [20] = 1
4.5
SATA
USB
SMBUS
PATA
AC97
HD AUDIO
RTC
ACPI
PM REG
A-LINK
X
I/O REG
XIOAPIC
LPC
PCI
For register details refer to
the sections check-marked
in the SP5100 Register
Reference Guide
OHCI Prefetch Settings
ASIC Rev
All Revs SP5100
Register Settings
ABCFG 0x80 [0] = 1
Function/Comment
This register in AB controls the USB OHCI controller
prefetch used for enhancing performance of ISO out
devices.
SATA
USB
SMBUS
PATA
AC97
HD AUDIO
RTC
ACPI
PM REG
A-LINK
X
I/O REG
XIOAPIC
2012 Advanced Micro Devices, Inc.
AMD SP5100 Register Programming Requirements
LPC
PCI
For register details refer to
the sections check-marked
in the SP5100 Register
Reference Guide
A-Link Express Settings - Indirect I/O Access
Page 32
4.6
B-Link Client’s Credit Variable Settings for the Downstream
Arbitration Equation
ASIC Rev
Register Settings
All Revs SP5100 ABCFG 0x9C [0] = 1
4.7
Disables the credit variable in the downstream arbitration
equation.
SATA
USB
SMBUS
PATA
AC97
HD AUDIO
RTC
ACPI
PM REG
A-LINK
X
I/O REG
XIOAPIC
LPC
PCI
For register details refer to
the sections check-marked
in the SP5100 Register
Reference Guide
Enabling Additional Address Bits Checking in Downstream
Register Programming
ASIC Rev
Register Settings
All Revs SP5100 ABCFG 0x9C [1] = 1
4.8
Function/Comment
Function/Comment
Register bit to qualify additional address bits into
downstream register programming.
SATA
USB
SMBUS
PATA
AC97
HD AUDIO
RTC
ACPI
PM REG
A-LINK
X
I/O REG
XIOAPIC
LPC
PCI
For register details refer to
the sections check-marked
in the SP5100 Register
Reference Guide
Set B-Link Prefetch Mode
ASIC Rev
Register Settings
All Revs SP5100 ABCFG 0x80 [17] = 1
ABCFG 0x80 [18] = 1
Function/Comment
Sets B-Link prefetch mode.
SATA
USB
SMBUS
PATA
AC97
HD AUDIO
RTC
ACPI
PM REG
A-LINK
X
I/O REG
XIOAPIC
2012 Advanced Micro Devices, Inc.
AMD SP5100 Register Programming Requirements
LPC
PCI
For register details refer to
the sections check-marked
in the SP5100 Register
Reference Guide
A-Link Express Settings - Indirect I/O Access
Page 33
4.9
Enabling Detection of Upstream Interrupts
ASIC Rev
Register Settings
Function/Comment
All Revs SP5100 ABCFG 0x94 [20] = 1
Enables A-Link Express logic to detect upstream interrupts
ABCFG 0x94 [19:0] = CPU interrupt delivery for the purposes of system management.
address [39:20].
SATA
USB
SMBUS
PATA
AC97
HD AUDIO
RTC
ACPI
PM REG
A-LINK
X
I/O REG
XIOAPIC
LPC
PCI
For register details refer to
the sections check-marked
in the SP5100 Register
Reference Guide
4.10 Enabling Downstream Posted Transactions to Pass NonPosted Transactions
ASIC Rev
Register Settings
All Revs SP5100 ABCFG 0x10090 [8] = 1
Function/Comment
Enables downstream posted transactions to pass nonposted transactions.
SATA
USB
SMBUS
PATA
AC97
HD AUDIO
RTC
ACPI
PM REG
A-LINK
X
I/O REG
XIOAPIC
LPC
PCI
For register details refer to
the sections check-marked
in the SP5100 Register
Reference Guide
4.11 Programming Cycle Delay for AB and BIF Clock Gating
ASIC Rev
Register Settings
All Revs SP5100 ABCFG 0x54 [23:16] = 0x4
ABCFG 0x10054 [23:16] = 0x4
ABCFG 0x98 [15:12] = 0x4
Function/Comment
Program # of cycles to delay before gating AB and BIF
clocks after idle condition.
SATA
USB
SMBUS
PATA
AC97
HD AUDIO
RTC
ACPI
PM REG
A-LINK
X
I/O REG
XIOAPIC
2012 Advanced Micro Devices, Inc.
AMD SP5100 Register Programming Requirements
LPC
PCI
For register details refer to
the sections check-marked
in the SP5100 Register
Reference Guide
A-Link Express Settings - Indirect I/O Access
Page 34
4.12 Enabling AB and BIF Clock Gating
ASIC Rev
Register Settings
All Revs SP5100 ABCFG 0x54[24] = 0
ABCFG 0x10054[24] = 1
ABCFG 0x98[11:8] = 0x7
Function/Comment
Enables the AB and BIF clock-gating logic.
SATA
USB
SMBUS
PATA
AC97
HD AUDIO
RTC
ACPI
PM REG
A-LINK
X
I/O REG
XIOAPIC
LPC
PCI
For register details refer to
the sections check-marked
in the SP5100 Register
Reference Guide
4.13 Enabling AB Int_Arbiter Enhancement
ASIC Rev
Register Settings
All Revs SP5100 ABCFG 0x10054[15:0] = 0x07FF
Function/Comment
Enables the A-Link int_arbiter enhancement to allow ALink bandwidth to be used more efficiently
SATA
USB
SMBUS
PATA
AC97
HD AUDIO
RTC
ACPI
PM REG
A-LINK
X
I/O REG
XIOAPIC
LPC
PCI
For register details refer to
the sections check-marked
in the SP5100 Register
Reference Guide
4.14 Enabling Requester ID
ASIC Rev
Register Settings
All Revs SP5100 ABCFG 0x98[16] = 1
Function/Comment
Enables the requester ID for upstream traffic
SATA
USB
SMBUS
PATA
AC97
HD AUDIO
RTC
ACPI
PM REG
A-LINK
X
I/O REG
XIOAPIC
LPC
PCI
For register details refer to
the sections check-marked
in the SP5100 Register
Reference Guide
4.15 Selecting the LPC FRAME# Assertion Timing on Power-up
ASIC Rev
Register Settings
SP5100 A14 and Lpc_PCI_config 0x8C [17] = 0
above
Function/Comment
Set the bit to 0 for revision A14 to assert LFRAME# signals
on SB Power good assertion.
Setting the bit to 1 will configure LPC to assert the
LFRAME# signal on de-assertion of SLP_S3# signal on
power up.
This register bit is not supported on A12 and should not be
programmed by the BIOS.
SATA
USB
SMBUS
PATA
AC97
HD AUDIO
RTC
ACPI
PM REG
A-LINK
I/O REG
XIOAPIC
2012 Advanced Micro Devices, Inc.
AMD SP5100 Register Programming Requirements
LPC
x
PCI
For register details, refer to
the sections check-marked
in the SP5100 Register
Reference Guide.
A-Link Express Settings - Indirect I/O Access
Page 35
4.16 SMI IO Write
ASIC Rev
SP5100 A12
Register Settings
Function/Comment
ABCFG 0x9C[8] = 1
IO write and SMI ordering enhancement enabled
SP5100 A14 and ABCFG 0x9C[8] = 0
above
IO write and SMI ordering enhancement disabled
SP5100 A15
SMI ordering enhancement enabled
ABCFG 0x90[21] = 1
ABCFG 0x9C[5] = 1
ABCFG 0x9C[9] = 1
ABCFG 0x9C[15] = 1
SATA
USB
SMBUS
PATA
AC97
HD AUDIO
RTC
ACPI
PM REG
A-LINK
X
I/O REG
XIOAPIC
LPC
PCI
For register details refer to
the sections check-marked
in the SP5100 Register
Reference Guide
4.17 Reset CPU on Sync Flood
ASIC Rev
Register Settings
SP5100 All Revs ABCFG 0x10050[2] = 1
Function/Comment
Enable SP5100 to initiate a CPU Reset on sync_flood.
This bit should be enabled in very early post.
SATA
USB
SMBUS
PATA
AC97
HD AUDIO
RTC
ACPI
PM REG
A-LINK
X
I/O REG
XIOAPIC
LPC
PCI
For register details, refer to
the sections check-marked
in the SP5100 Register
Reference Guide.
4.18 Enabling Posted Pass Non-Posted Downstream
ASIC Rev
SP5100 A15
Register Settings
AX_INDXC 0x2[9] = 1
ABCFG 0x9C[6] = 1
ABCFG 0x9C[7] = 1
ABCFG 0x9C[10] = 1
ABCFG 0x9C[11] = 1
ABCFG 0x9C[12] = 1
ABCFG 0x9C[13] = 1
ABCFG 0x9C[14] = 1
ABCFG 0x1009C [4] = 1
ABCFG 0x1009C [5] = 1
ABCFG 0x10090 [9] = 1
ABCFG 0x10090 [10] = 1
ABCFG 0x10090 [11] = 1
ABCFG 0x10090 [12] = 1
Function/Comment
Posted pass non-posted downstream direction feature
enable.
SATA
USB
SMBUS
PATA
AC97
HD AUDIO
RTC
ACPI
PM REG
A-LINK
X
I/O REG
XIOAPIC
2012 Advanced Micro Devices, Inc.
AMD SP5100 Register Programming Requirements
LPC
PCI
For register details, refer to
the sections check-marked
in the SP5100 Register
Reference Guide.
A-Link Express Settings - Indirect I/O Access
Page 36
4.19 Enabling Posted Pass Non-Posted Upstream
ASIC Rev
SP5100 A15
Register Settings
ABCFG 0x58[11] = 1
ABCFG 0x58[15:12] = 0xE
Function/Comment
Posted pass non-posted upstream direction feature
enable.
SATA
USB
SMBUS
PATA
AC97
HD AUDIO
RTC
ACPI
PM REG
A-LINK
X
I/O REG
XIOAPIC
LPC
PCI
For register details, refer to
the sections check-marked
in the SP5100 Register
Reference Guide.
4.20 64 bit Non-Posted Memory Write Support
ASIC Rev
SP5100 A15
Register Settings
AX_INDXC 0x2[10] = 1
Function/Comment
Enable support of 64-bit Non-Posted Memory Writes.
SATA
USB
SMBUS
PATA
AC97
HD AUDIO
RTC
ACPI
PM REG
A-LINK
X
I/O REG
XIOAPIC
2012 Advanced Micro Devices, Inc.
AMD SP5100 Register Programming Requirements
LPC
PCI
For register details, refer to
the sections check-marked
in the S SP5100 Register
Reference Guide.
A-Link Express Settings - Indirect I/O Access
Page 37
5 PCIB (PCI-bridge, bus-0, dev-20, fun-04)
5.1
Enabling PCI-bridge Subtractive Decode
ASIC REV
All Revs SP5100
5.2
Register Settings
PCIB_PCI_config 0x40 [5] = 1
PCIB_PCI_config 0x4B [7]= 1
Enables the PCI-bridge subtractive decode.
This setting is strongly recommended since it supports some
legacy PCI add-on cards.
SATA
USB
SMBUS
PATA
AC97
HD AUDIO
RTC
ACPI
PM REG
A-LINK
I/O REG
XIOAPIC
LPC
PCI
X
For register details refer to
the sections check-marked
in the SP5100 Register
Reference Guide
PCI-bridge Upstream Dual Address Window
ASIC REV
All Revs SP5100
5.3
Function/Comment
Register Settings
PCIB_PCI_config 0x50 [0] = 1
Function/Comment
PCI-bridge upstream dual address window.
This setting is applicable if the system memory is more than
4GB, and the PCI devices can support dual address access.
SATA
USB
SMBUS
PATA
AC97
HD AUDIO
RTC
ACPI
PM REG
A-LINK
I/O REG
XIOAPIC
LPC
PCI
X
For register details refer to
the sections check-marked
in the SP5100 Register
Reference Guide
PCI Bus 64-byte DMA Read Access
ASIC REV
All Revs SP5100
Register Settings
PCIB_PCI_config 0x4B [4] = 1 (default)
Function/Comment
PCI bus 64-byte DMA read access.
Enhances the PCI bus DMA performance.
SATA
USB
SMBUS
PATA
AC97
HD AUDIO
RTC
ACPI
PM REG
A-LINK
I/O REG
XIOAPIC
2012 Advanced Micro Devices, Inc.
AMD SP5100 Register Programming Requirements
LPC
PCI
X
For register details refer to
the sections check-marked
in the SP5100 Register
Reference Guide
PCIB (PCI-bridge, bus-0, dev-20, fun-04)
Page 38
5.4
PCI Bus DMA Write Cacheline Alignment
ASIC REV
All Revs SP5100
5.5
Register Settings
PCIB_PCI_config 0x40 [1] = 1 (default)
Enables the PCIB writes to be cacheline aligned.
The size of the writes will be set in the Cacheline Register
(PCIB_PCI_config 0x4B[4:0]). Refer to section 5.3 for more
information.
SATA
USB
SMBUS
PATA
AC97
HD AUDIO
RTC
ACPI
PM REG
A-LINK
I/O REG
XIOAPIC
LPC
PCI
X
For register details refer to
the sections check-marked
in the SP5100 Register
Reference Guide
Master Latency Timer
ASIC REV
All Revs SP5100
5.6
Function/Comment
Register Settings
PCIB_PCI_config 0x0D = 0x40 (default)
PCIB_PCI_config 0x1B = 0x40 (default)
Function/Comment
Enables the PCIB to retain ownership of the bus on the
Primary side and on the Secondary side when GNT# is deasserted.
Note: This setting is mandatory.
SATA
USB
SMBUS
PATA
AC97
HD AUDIO
RTC
ACPI
PM REG
A-LINK
I/O REG
XIOAPIC
LPC
PCI
X
For register details refer to
the sections check-marked
in the SP5100 Register
Reference Guide
DMA Read Command Match
ASIC REV
All Revs SP5100
Register Settings
PCIB_PCI_config 0x4B[6] = 1 (default)
Function/Comment
Enables the command matching checking function on
“Memory Read” & “Memory Read Line” commands.
Some PCI devices may change the “Memory read
command” to “Memory read line” command before the data
is completed. This bit enables the command matching
checking inside the PCIB to work with this kind of device.
Note: This setting is mandatory.
SATA
USB
SMBUS
PATA
AC97
HD AUDIO
RTC
ACPI
PM REG
A-LINK
I/O REG
XIOAPIC
2012 Advanced Micro Devices, Inc.
AMD SP5100 Register Programming Requirements
LPC
PCI
X
For register details refer to
the sections check-marked
in the SP5100 Register
Reference Guide
PCIB (PCI-bridge, bus-0, dev-20, fun-04)
Page 39
5.7
Enabling Idle To Gnt# Check
ASIC REV
All Revs SP5100
5.8
Register Settings
PCIB_PCI_config 0x4B [0] = 1 (default)
When enabled, the PCI arbiter checks for the Bus Idle
before asserting GNT#.
Note: This setting is recommended.
SATA
USB
SMBUS
PATA
AC97
HD AUDIO
RTC
ACPI
PM REG
A-LINK
I/O REG
XIOAPIC
LPC
PCI
X
For register details refer to
the sections check-marked
in the SP5100 Register
Reference Guide
GNT# Timing Adjustment
ASIC REV
All Revs SP5100
5.9
Function/Comment
Register Settings
PCIB_PCI_config 0x64 [12] = 1 (default)
Function/Comment
Adjusts the GNT# de-assertion time.
Note: This setting is recommended.
SATA
USB
SMBUS
PATA
AC97
HD AUDIO
RTC
ACPI
PM REG
A-LINK
I/O REG
XIOAPIC
LPC
PCI
X
For register details refer to
the sections check-marked
in the SP5100 Register
Reference Guide
Enabling Fast Back to Back Retry
ASIC REV
All Revs SP5100
Register Settings
PCIB_PCI_config 0x48 [2] = 1 (default)
Function/Comment
Enables Fast Back to Back transactions support.
Note: This setting is recommended
SATA
USB
SMBUS
PATA
AC97
HD AUDIO
RTC
ACPI
PM REG
A-LINK
I/O REG
XIOAPIC
LPC
PCI
X
For register details refer to
the sections check-marked
in the SP5100 Register
Reference Guide
5.10 Enabling Lock Operation
ASIC REV
All Revs SP5100
Register Settings
PCIB_PCI_config 0x48 [3] = 1 (default)
Function/Comment
This bit should be set to 1 when PCI configuration space
PCIB_PCI config 0x40 [2] = 1 for the proper operation of
the PCI LOCK# function.
SATA
USB
SMBUS
PATA
AC97
HD AUDIO
RTC
ACPI
PM REG
A-LINK
I/O REG
XIOAPIC
2012 Advanced Micro Devices, Inc.
AMD SP5100 Register Programming Requirements
LPC
PCI
X
For register details refer to
the sections check-marked
in the SP5100 Register
Reference Guide
PCIB (PCI-bridge, bus-0, dev-20, fun-04)
Page 40
5.11 Enabling Additional Optional PCI Clock (PCICLK5)
ASIC REV
All Revs SP5100
Register Settings
Function/Comment
PCIB_PCI_config 0x64 [8] = 1
This only applies when PCICLK5/PCIREQ5#/PCIGNT5#
are enabled: When this bit is set, PCICLK5, PCIREQ#5,
and PCIGNT5# are enabled for PCI use. Since PCICLK5 is
not enabled by default (the clock is off), the PCI device
which uses this clock may not see the system reset during
power-up. To correct this, the BIOS should write to PCIB
config 3Eh, bit [6] to assert the additional PCI reset so the
device will see a proper reset, as well as to provide the
time for its internal PLL to lock. The recommended
duration time is at least a few milliseconds.
Note: These three pins are enabled as a group, therefore,
care should be taken to make sure they are used properly.
SATA
USB
SMBUS
PATA
AC97
HD AUDIO
RTC
ACPI
PM REG
A-LINK
I/O REG
XIOAPIC
LPC
PCI
X
For register details refer to
the sections check-marked
in the SP5100 Register
Reference Guide
5.12 Enabling One-Prefetch-Channel Mode
ASIC REV
All Revs SP5100
Register Settings
Function/Comment
PCIB_PCI_config 0x64 [20] = 0x1
Enables One-Prefetch-Channel Mode.
Note: This setting is mandatory.
SATA
USB
SMBUS
PATA
AC97
HD AUDIO
RTC
ACPI
PM REG
A-LINK
I/O REG
XIOAPIC
LPC
PCI
X
For register details refer to
the sections check-marked
in the SP5100 Register
Reference Guide
5.13 Disabling PCIB MSI Capability
ASIC REV
All Revs SP5100
Register Settings
Function/Comment
PCIB_PCI_config 0x40 [3] = 0x0 (default)
Disables MSI capability.
SATA
USB
SMBUS
PATA
AC97
HD AUDIO
RTC
ACPI
PM REG
A-LINK
I/O REG
XIOAPIC
2012 Advanced Micro Devices, Inc.
AMD SP5100 Register Programming Requirements
LPC
PCI
X
For register details refer to
the sections check-marked
in the SP5100 Register
Reference Guide
PCIB (PCI-bridge, bus-0, dev-20, fun-04)
Page 41
5.14 Adjusting CLKRUN#
ASIC REV
All Revs SP5100
Register Settings
PCIB_PCI_config 0x64 [15] = 0x1
Function/Comment
This bit should be set to 1 for the proper operation of
CLKRUN#.
Note: This setting is mandatory.
SATA
USB
SMBUS
PATA
AC97
HD AUDIO
RTC
ACPI
PM REG
A-LINK
I/O REG
XIOAPIC
2012 Advanced Micro Devices, Inc.
AMD SP5100 Register Programming Requirements
LPC
PCI
X
For register details refer to
the sections check-marked
in the SP5100 Register
Reference Guide
PCIB (PCI-bridge, bus-0, dev-20, fun-04)
Page 42
6 USB – OHCI & EHCI controllers (bus-0, dev-18/19, fun-00
~02/ bus-0, dev-20, fun-05)
Please note the following information for this section:
• EHCI BAR address = EHCI_PCI_config 0x10[31:8]
• EHCI_EOR is the EHCI operation register = EHCI_BAR + 0x20
• The device list for all USB Controllers is as follows:
6.1
Device List
Function/Comment
Bus-0, dev-18, fun-0
USB1, OHCI0
Bus-0, dev-18, fun-1
USB1, OHCI1
Bus-0, dev-18, fun-1
USB1, EHCI
Bus-0, dev-19, fun-0
USB2, OHCI0
Bus-0, dev-19, fun-1
USB2, OHCI1
Bus-0, dev-19, fun-1
USB2, EHCI
Bus-0, dev-20, fun-5
USB3, OHCI
Enabling/Disabling OHCI and EHCI Controllers
ASIC Rev
All Revs SP5100
SATA
USB
RTC
ACPI
Register Settings
Function/Comment
Smbus_PCI_config 0x68 [2] = 1 (default)
Enables the USB1 (bus-0, dev-18) EHCI controller.
Smbus_PCI_config 0x68 [0] = 1 (default)
Enables the USB1 (bus-0, dev-18) OHCI controller 1
(OHCI0).
Smbus_PCI_config 0x68 [1] = 1 (default)
Enables the USB1 (bus-0, dev-18) OHCI controller 2
(OHCI1).
Smbus_PCI_config 0x68 [6] = 1 (default)
Enables the USB2 (bus-0, dev-19) EHCI controller.
Smbus_PCI_config 0x68 [4] = 1 (default)
Enables the USB2 (bus-0, dev-19) OHCI controller 1
(OHCI0).
Smbus_PCI_config 0x68 [5] = 1 (default)
Enables the USB2 (bus-0, dev-19) OHCI controller 2
(OHCI1).
Smbus_PCI_config 0x68 [7] = 1 (default)
Enables the USB3 (bus-0, dev-20, fun-5) OHCI controller.
SMBUS
X
PM REG
PATA
AC97
HD AUDIO
A-LINK
I/O REG
XIOAPIC
2012 Advanced Micro Devices, Inc.
LPC
PCI
For register details, refer to
the sections check-marked
in the SP5100 Register
Reference Guide.
USB – OHCI & EHCI controllers (bus-0, dev-18/19, fun-00 ~02/
bus-0, dev-20, fun-05)
AMD SP5100 Register Programming Requirements
Page 43
6.2 USB Device Support to Wake Up System from S3/S4 State
ASIC Rev
All Revs SP5100
Register Settings
Function/Comment
PM_IO 0x61 [6] = 1
PM_IO 0x65 [2] = 1 (default)
Enables the USB PME event.
Enables USB resume support.
PM_IO 0x65 [6] = 1
Enable PME generation for USB Wake event from connect
and disconnect of USB devices.
Note: BIOS workaround A2 described in Appendix A must be
implemented for this feature to work reliably. Without the
workaround PME Wake for Connect/Disconnect of USB 1.1
devices will not be supported.
6.3
SATA
USB
SMBUS
PATA
AC97
HD AUDIO
RTC
ACPI
PM REG
X
A-LINK
I/O REG
XIOAPIC
PCI
For register details refer to
the sections check-marked
in the SP5100 Register
Reference Guide
USB S4/S5 Wakeup or PHY Power Down Support
ASIC Rev
Register Settings
All Revs SP5100 PM_IO 0x65 [0] = 0 (default)
6.4
LPC
Function/Comment
This bit = 0 (default) supports USB device wakeup from the
S4/S5 state.
Set the bit to 1 to disable the USB S4/S5 wakeup function.
The analog power supply to USB PHY on the motherboard
can be OFF in this case to save S4/S5 power.
SATA
USB
SMBUS
PATA
AC97
HD AUDIO
RTC
ACPI
PM REG
X
A-LINK
I/O REG
XIOAPIC
LPC
PCI
For register details refer to
the sections check-marked
in the SP5100 Register
Reference Guide
USB PHY Auto Calibration Setting
ASIC Rev
Register Settings
All Revs SP5100 EHCI_BAR 0xC0 = 0x00020F00
SATA
RTC
USB
X
ACPI
Function/Comment
Enables the USB PHY auto calibration resistor to match
45ohm resistance.
SMBUS
PATA
AC97
HD AUDIO
PM REG
A-LINK
I/O REG
XIOAPIC
2012 Advanced Micro Devices, Inc.
LPC
PCI
For register details refer to
the sections check-marked
in the SP5100 Register
Reference Guide
USB – OHCI & EHCI controllers (bus-0, dev-18/19, fun-00 ~02/
bus-0, dev-20, fun-05)
AMD SP5100 Register Programming Requirements
Page 44
6.5
USB Reset Sequence
ASIC Rev
Register Settings
Function/Comment
All Revs SP5100 PM_IO 0x65 [4] = 1
Enables the USB controller to get reset by any software that
generates a PCIRst# condition. However, this bit should be
cleared before a software generated reset condition occurs
during S3 resume so the USB controller will not lose the
connection status during the S3 resume procedure.
The software generated PCIRst# conditions include
Keyboard Reset, or write to the IO-CF9 register.
6.6
SATA
USB
SMBUS
PATA
AC97
HD AUDIO
RTC
ACPI
PM REG
X
A-LINK
I/O REG
XIOAPIC
PCI
For register details refer to
the sections check-marked
in the SP5100 Register
Reference Guide
USB Advanced Sleep Control
ASIC Rev
Register Settings
All Revs SP5100 PM_IO 0x95 [2:0] = 110b
6.7
LPC
Function/Comment
Enables the USB EHCI controller advance sleep mode
function to improve power saving.
SATA
USB
SMBUS
PATA
AC97
HD AUDIO
RTC
ACPI
PM REG
X
A-LINK
I/O REG
XIOAPIC
LPC
PCI
For register details refer to
the sections check-marked
in the SP5100 Register
Reference Guide
USB 48 MHz Clock Source Settings
ASIC Rev
Register Settings
All Revs SP5100 PM_IO 0xD0 [0] = 0 (default)
Function/Comment
Enables PLL “CG_PLL2” to generate 48Mhz clock internally.
PM_IO 0xBD [4] = 1
Enables the internal 48Mhz as the clock source to
USBPHY
PM_IO 0xBD [6] = 1 (optional)
Enables the IO pad “USBCLK/14M_25M_48M” as clock
output pad that it can be used for on board devices. This is
optional (depending on board requirement).
Note: To use internal 48 MHz clock, the 100 MHz PCIe clock sourced from the external clock chip must not have spread
spectrum enabled.
SATA
RTC
USB
X
ACPI
SMBUS
PATA
AC97
HD AUDIO
PM REG
A-LINK
I/O REG
XIOAPIC
2012 Advanced Micro Devices, Inc.
LPC
PCI
For register details refer to
the sections check-marked
in the SP5100 Register
Reference Guide
USB – OHCI & EHCI controllers (bus-0, dev-18/19, fun-00 ~02/
bus-0, dev-20, fun-05)
AMD SP5100 Register Programming Requirements
Page 45
6.8
Adjusting USB 2.0 Ports Driving Strength
ASIC Rev
Register Settings
All Revs SP5100 Step 1:
Function/Comment
Adjusts the USB2.0 ports driving strength.
EHCI_BAR 0xB4 [2:0] = “HSADJ”
EHCI_BAR 0xB4[12] = 0
EHCI_BAR 0xB4 [16:13] = “port#”
HSADJ to set the driving strength value
VLoadB to load the value to the PHY for selected port
The selected port#
The SBIOS can repeat step-1 for those ports with less
margin on HS eye diagram.
Step 2:
EHCI_BAR 0xB4[12] = 1
Set to ‘1’ to lock PHY UTMI Control interface.
Note:
1. Different board designs may require different settings for different ports depending on trace length and routing.
2. Only apply the setting to the ports that have longer USB trace lengths (> 12 inches) to the connector, and if the eye
diagram margin is not enough. There is no need to apply these setting to the ports with shorter trace lengths or
close to the USB connectors.
3. EHCI_BAR 0xB4 = EHCI_EOR 0x94 (UTMI Control Register)
4. EHCI_BAR 0xB4[2:0] (HSADJ)
“000” = -10% , “001” = -5%, “100” = 0%, “101” = +5%, “110” = +10%
EHCI_BAR 0xB4[16:13] (port#)
“0000” = port0 , “0001” = port1, …… “0101” = port5, 0110 ~ 1110: reserved.
SATA
RTC
6.9
USB
X
ACPI
SMBUS
PATA
AC97
HD AUDIO
PM REG
A-LINK
I/O REG
XIOAPIC
LPC
PCI
For register details refer to
the sections check-marked
in the SP5100 Register
Reference Guide
In and Out Data Packet FIFO Threshold
ASIC Rev
Register Settings
All Revs SP5100 EHCI_BAR 0xA4 = 0x00400040
SATA
RTC
USB
X
ACPI
Function/Comment
IN/OUT data packet FIFO threshold for EHCI controllers.
Normal operation the FIFO threshold settings
FIFO threshold setting must be programmed in both the
EHCI host controllers,
Bus-0, dev-18 fun 2 and Bus 0 dev-19 fun-2
SMBUS
PATA
AC97
HD AUDIO
PM REG
A-LINK
I/O REG
XIOAPIC
2012 Advanced Micro Devices, Inc.
LPC
PCI
For register details refer to
the sections check-marked
in the SP5100 Register
Reference Guide
USB – OHCI & EHCI controllers (bus-0, dev-18/19, fun-00 ~02/
bus-0, dev-20, fun-05)
AMD SP5100 Register Programming Requirements
Page 46
6.10 OHCI MSI Function Setting
ASIC Rev
Register Settings
All Revs SP5100 OHCI0_PCI_Config 0x40[9:8] = ”11”
Function/Comment
OHCI MSI function
For normal operation the MSI function must be disabled by
setting bits [9:8] on dev-18, fun-0, and dev-19, fun-0, OHCI
controllers and bit [8] on dev-20, fun-5, OHCI controller.
bus-0, dev-18 fun 0 / bus-0, dev-19 fun 0
bus-0, dev-20, fun-5.
SATA
RTC
USB
X
ACPI
SMBUS
PATA
AC97
HD AUDIO
PM REG
A-LINK
I/O REG
XIOAPIC
LPC
PCI
For register details refer to
the sections check-marked
in the SP5100 Register
Reference Guide
6.11 EHCI Advance Asynchronous Enhancement
See section 6.22
6.12 EHCI Advance PHY Power Savings
ASIC Rev
Register Settings
Function/Comment
SP5100 A11
EHCI_PCI_Config 0x50[31] = 0
Disables Advance PHy power saving for normal operation.
This register bit defaults to ‘0’ on power up. The BIOS
should not program this register bit to 1 in both EHCI
controllers.
Bus-0, dev-18 fun 2 and Bus 0 dev-19 fun-2
SP5100 A12
EHCI_PCI_Config 0x50[31] = 1
Enables Advance PHY power saving feature.
The BIOS should program this register bit to 1 in both
EHCI controllers.
Bus-0, dev-18 fun 2 and Bus 0 dev-19 fun-2
SATA
RTC
USB
X
ACPI
SMBUS
PATA
AC97
HD AUDIO
PM REG
A-LINK
I/O REG
XIOAPIC
2012 Advanced Micro Devices, Inc.
LPC
PCI
For register details refer to
the sections check-marked
in the SP5100 Register
Reference Guide
USB – OHCI & EHCI controllers (bus-0, dev-18/19, fun-00 ~02/
bus-0, dev-20, fun-05)
AMD SP5100 Register Programming Requirements
Page 47
6.13 Enabling Fix for EHCI Controller Driver Yellow Sign Issue
ASIC Rev
SP5100 A12
SATA
RTC
USB
X
ACPI
Register Settings
EHCI_PCI_Config 0x50[20] = 1
Function/Comment
Enables the fix for the yellow sign issue observed when the
HSET driver gets unloaded and the in box EHCI driver gets
loaded.
SMBUS
PATA
AC97
HD AUDIO
PM REG
A-LINK
I/O REG
XIOAPIC
LPC
PCI
For register details refer to
the sections check-marked
in the SP5100 Register
Reference Guide
6.14 Enabling Fix to Cover the Corner Case S3 Wake Up Issue
ASIC Rev
SP5100 A12
SATA
RTC
USB
X
ACPI
Register Settings
OHCI 0_PCI_Config 0x50[16] = 1
Function/Comment
Enables the fix to cover the corner case S3 wake up issue
seen with some specific USB 1.1 keyboards.
SMBUS
PATA
AC97
HD AUDIO
PM REG
A-LINK
I/O REG
XIOAPIC
LPC
PCI
For register details refer to
the sections check-marked
in the SP5100 Register
Reference Guide
6.15 EHCI Async Park Mode
See section 6.20
6.16 MSI Feature in USB 2.0 Controller
ASIC Rev
Register Settings
All Revs SP5100 EHCI_PCI_Config 0x50[6] = 1
SATA
RTC
USB
X
ACPI
Function/Comment
MSI function
For normal operation the MSI function should be disabled
by setting the bit in both EHCI controllers.
Bus-0, dev-18 fun 2 and Bus 0 dev-19 fun-2
SMBUS
PATA
AC97
HD AUDIO
PM REG
A-LINK
I/O REG
XIOAPIC
2012 Advanced Micro Devices, Inc.
LPC
PCI
For register details refer to
the sections check-marked
in the SP5100 Register
Reference Guide
USB – OHCI & EHCI controllers (bus-0, dev-18/19, fun-00 ~02/
bus-0, dev-20, fun-05)
AMD SP5100 Register Programming Requirements
Page 48
6.17 EHCI Dynamic Clock Gating Feature
ASIC Rev
Register Settings
All Revs SP5100 EHCI_BAR 0xBC Bit[12] = 0
SATA
RTC
USB
X
ACPI
Function/Comment
For normal operation, the clock gating feature must be
disabled. At system reset, this bit is set to “1”. So, BIOS
needs to program this bit to “0”.
EHCI clock gating setting must be programmed in both the
EHCI host controllers.
Bus-0, dev-18 fun 2 and Bus 0 dev-19 fun-2
SMBUS
PATA
AC97
HD AUDIO
PM REG
A-LINK
I/O REG
XIOAPIC
LPC
PCI
For register details refer to
the sections check-marked
in the SP5100 Register
Reference Guide
6.18 USB 1.1 ISO OUT Devices/Speaker Noise
ASIC Rev
SP5100 A14 and a.
above
b.
Register Settings
Function/Comment
ABCFG 0x90[17] = 1
OHCI0 PCI_Config 0x50[25] = 1
Settings a and b are required for revision A14 and above to
resolve the USB 1.1 speaker noise issue as described in
A12 Errata item #8.
The bits must be programmed in all three OHCI controllers:
Bus-0 Dev-18 Func-0, Bus-0 Dev-19 Func-0, and Bus-0
Dev-20 Func-5.
SATA
RTC
USB
x
ACPI
SMBUS
PATA
AC97
HD AUDIO
PM REG
A-LINK
X
I/O REG
XIOAPIC
LPC
PCI
For register details, refer to
the sections check-marked
in the SP5100 Register
Reference Guide.
6.19 USB Controller DMA Read Delay Tolerant
ASIC Rev
Register Settings
SP5100 A14 and EHCI_PCI_Config 0x50[7] =0
above
Function/Comment
This bit should not be programmed by software. It should
be left at hardware default setting of ‘0’. Setting this bit to 1
may cause system hang due to long memory read delays
that can occur when the system is in PM states or when
other clients, such as integrated GFX, get higher priority to
memory.
Note: Bit 7 of both EHCI host controllers (Bus-0 Dev-18
Func-2, and Bus-0 Dev-19 Func-2) should be left at ‘0’.
SATA
RTC
USB
X
ACPI
SMBUS
PATA
AC97
HD AUDIO
PM REG
A-LINK
I/O REG
XIOAPIC
2012 Advanced Micro Devices, Inc.
LPC
PCI
For register details, refer to
the sections check-marked
in the SP5100 Register
Reference Guide.
USB – OHCI & EHCI controllers (bus-0, dev-18/19, fun-00 ~02/
bus-0, dev-20, fun-05)
AMD SP5100 Register Programming Requirements
Page 49
6.20 Async Park Mode
ASIC Rev
Register Settings
SP5100 All Revs EHCI PCI_Config 0x50[23] = 1
Function/Comment
Async Park Mode function.
For normal operation, the APM function should be disabled
by setting the bit in both EHCI controllers:
Bus-0 Dev-18 Func-2 and Bus 0 Dev-19 Func-2
If EHCI APM is enabled, some USB card reader devices
may not work properly. The USB controller used on these
devices may not be able to handle the short delay time
between the data packets.
SP5100 A14 and EHCI PCI_Config 0x50[2] = 0
above
Disable Async Park Extra Mode function.
This is hardware default; BIOS should not program the
register.
This bit should be disabled in USB1 EHCI controller only.
Bus-0 Dev-18 Func-2.
The bit in Bus-0 Dev-19 Func-2 is reserved and should not
be programmed.
SATA
RTC
USB
X
ACPI
SMBUS
PATA
AC97
HD AUDIO
PM REG
A-LINK
I/O REG
XIOAPIC
LPC
PCI
For register details, refer to
the sections check-marked
in the SP5100 Register
Reference Guide.
6.21 Resume Reset Timing
ASIC Rev
Register Settings
SP5100 A14 and OHCI 0 PCI_Config 0x50[17] = 1
above
Function/Comment
Set this bit to 1 on revision A14. This register setting is
required to enable the Reset Timing feature. This feature will
resolve the issue listed in A12 Errata (item #7).
The bit must be programmed in both of the OHCI0
controllers:
Bus-0 Dev-18 Func- 0 and Bus 0 Dev-19 Func-0
SATA
USB
SMBUS
PATA
AC97
HD AUDIO
PM REG
A-LINK
I/O REG
XIOAPIC
LPC
PCI
X
RTC
ACPI
For register details, refer to
the sections check-marked
in the SP5100 Register
Reference Guide.
6.22 Disable Async QH Cache
ASIC Rev
SP5100 A15
SATA
Register Settings
EHCI PCI Config 0x50[25] = 1
USB
Function/Comment
Disable Async QH/QTD Cache
SMBUS
PATA
AC97
HD AUDIO
PM REG
A-LINK
I/O REG
XIOAPIC
X
RTC
ACPI
2012 Advanced Micro Devices, Inc.
LPC
PCI
For register details, refer to
the sections check-marked
in the SP5100 Register
Reference Guide.
USB – OHCI & EHCI controllers (bus-0, dev-18/19, fun-00 ~02/
bus-0, dev-20, fun-05)
AMD SP5100 Register Programming Requirements
Page 50
6.23 Advance Async Enhancement
ASIC Rev
SP5100 A12
Register Settings
EHCI PCI Config 0x50[28] = 1
Function/Comment
Advance asynchronous enhancement function.
For normal operation, the AAE function should be disabled
by setting the bit in both EHCI controllers:
Bus-0 Dev-18 Func-2 and Bus-0 Dev-19 Func-2
Enabling this function may cause USB 2.0 device to
malfunction or be undetected.
SP5100 A14 and EHCI_PCI_Config 0x50[3] =1
above
EHCI PCI Config 0x50[28] = 0
Set this bit 3 to 1
Clear this bit 28
This enhancement on A14 and above will improve the USB
performance when more than one USB device is
connected.
The bits must be programmed in both of the EHCI host
controllers:
Bus-0 Dev-18 Func-2 and Bus-0 Dev-19 Func-2
SATA
USB
SMBUS
PATA
AC97
HD AUDIO
PM REG
A-LINK
I/O REG
XIOAPIC
LPC
PCI
X
RTC
ACPI
For register details, refer to
the sections check-marked
in the SP5100 Register
Reference Guide.
6.24 USB Periodic Cache Setting
ASIC Rev
SP5100 A12
Register Settings
EHCI_PCI_Config 0x50[27] =1
SP5100 A14 and EHCI_PCI_Config 0x50[8] =1
above
EHCI_PCI_Config 0x50[27] =0
Function/Comment
Set this bit to 1 on revision A12
Should be done for non Windows OS only.
The bit must be programmed in both of the EHCI host
controllers:
Bus-0 Dev-18 Func-2 and Bus 0 Dev-19 Func-2
Set bit 8 to 1 on revision A14 and above
Clear bit 8 or do not program if untouched after power up.
The bits must be programmed in both of the EHCI host
controllers:
Bus-0, Dev-18 Func-2 and Bus 0 Dev-19 Func-2
SATA
USB
SMBUS
PATA
AC97
HD AUDIO
PM REG
A-LINK
I/O REG
XIOAPIC
X
RTC
ACPI
2012 Advanced Micro Devices, Inc.
LPC
PCI
For register details, refer to
the sections check-marked
in the SP5100 Register
Reference Guide.
USB – OHCI & EHCI controllers (bus-0, dev-18/19, fun-00 ~02/
bus-0, dev-20, fun-05)
AMD SP5100 Register Programming Requirements
Page 51
6.25 USB PID_ERROR_CHECKING
ASIC Rev
SP5100 A15
Register Settings
EHCI_PCI_Config 0x50[9] =1
Function/Comment
Set this bit to enable the Error checking on PID
Bus-0 Dev-18 Func-2 and Bus 0 Dev-19 Func-2
SATA
USB
X
SMBUS
PATA
AC97
HD AUDIO
RTC
ACPI
PM REG
A-LINK
I/O REG
XIOAPIC
2012 Advanced Micro Devices, Inc.
LPC
PCI
For register details, refer to
the sections check-marked
in the SP5100 Register
Reference Guide.
USB – OHCI & EHCI controllers (bus-0, dev-18/19, fun-00 ~02/
bus-0, dev-20, fun-05)
AMD SP5100 Register Programming Requirements
Page 52
7 SATA: dev-17, func-0
7.1
Enabling SATA
ASIC Rev
All Revs SP5100
7.2
Register Settings
Smbus_PCI_config 0xAC [8] = 1
Function/Comment
Enables the SATA controller.
SATA Initialization
ASIC Rev
Register Settings
All Revs SP5100 Smbus_PCI_config 0xAC [28:26]
SP5100 A12
This bit needs to be cleared to convert the subclass code
register to read-only. Refer to section 7.6 for the SATA
subclass programming sequence.
SATA_PCI_config 0x44 [0] = 1
Enables the SATA watchdog timer register prior to the SATA
BIOS post. See Note.
SATA_PCI_config 0x40 [29] = 1
SATA_PCI_config 0x48 [24] = 1
Set bit 29 and 24 for A12.
Bit 29 and 24 on A14 are cleared on power-up. These bits
can be set to 0 or not programmed.
Restore the registers on the following conditions:
SP5100 A12
SP5100 A14 and
above
ASIC Revision
A12
A14, A15
Yes
Yes
Yes
No
Yes
No
SATA_PCI_config 0x48 [21] = 1
SATA_PCI_config 0x48 [21] = 0
Restore the registers on the following conditions
Restore after
S3
S4
Warm boot
SATA interrupt mapping to PCI interrupt pins. These bits
should be programmed by the BIOS for correct assignment
of SATA interrupt mapping/
SATA_PCI_config 0x40 [0] = 0
SP5100 A14 and SATA_PCI_config 0x40 [29] = 0
above
SATA_PCI_config 0x48 [24] = 0
Restore after
S3
S4
Warm boot
Function/Comment
ASIC Revision
A12
A14, A15
Yes
Yes
Yes
No
Yes
No
2012 Advanced Micro Devices, Inc.
AMD SP5100 Register Programming Requirements
Clearing bit 29 and 24 will enable the hardware to send the
byte count updates during the AHCI mode PIO transfers to
meet the SATA Specification. On A12, the byte count
updates are not sent and the bit should be left as 0. The
feature is required only for certain vendor-specific
diagnostics that check the updated byte counts status. There
is no functional impact as the OS drivers do not check for the
byte count during the PIO transfer but only after the transfer
is completed. On both A12 and A14, the byte count is
updated after the transfer is completed, even without this
feature enabled.
Set bit 21 for A12
Bit 21 on A14 and above is cleared on power up. This bit
can be set to 0 or not programmed.
Clearing the bit will enable the compatibility feature. It
allows the SATA controller to be able to handle the case
where the device might follow COMWAKE with one Align
instead of multiple Aligns as required normally. This is not
a normal case for the devices, but was observed on one of
the SATA devices during qualification.
SATA: dev-17, func-0
Page 53
SP5100 A14 and
above
SATA_PCI_config 0x48 [13:7] = 7’h7F
SATA_PCI_config 0x48 [14] = 0 (
default)
SATA_PCI_config 0x48 [15] = 1
The setting to these register bits should
be restored to 1 for A14
1. On resume from S3 and S4.
2. After warm boot reset.
The registers listed here apply only to revision A14 and
above. These bits enable enhancements made in the A14
and above to address compatibility or minor spec violation
issues seen in simulation. The SATA test/enhancement
mode should be enabled by programming these registers to
1s. The default power-up setting for these registers are 0s.
SP5100 A14 and
above
SATA_PCI_config 0x48 [6] = 1
Setting this bit to 1 will allow the Activity LED to go off when
there is no activity and the driver does not send additional
commands due to user intervention of the Vista OS boot
process (by pressing the F8 key). Applies to configuration in
which the ODD is attached to Slave Port in IDE mode.
SP5100 A14 and
above
Smbus_PCI_config 0xAC [13] = 0
The SATA test/enhancement mode should be enabled by
programming this register to 0. The default power-up setting
for this register is 1. The setting to this register bit should be
restored to 0 for A14 and above.
1. On resume from S3 and S4
2. After warm boot reset
All Revs SP5100
SATA_BAR5 + Port offset + 0x10 =
FFFFh
This setting applies only when BIOS is using IDE to AHCI or
AMD IDE to AHCI modes.
To clear the error status, software needs to write 1 to this
register. For all SATA ports that are going to be visible to the
OS, BIOS should write 1 to bits [31:00] of the corresponding
port register just before passing the control to the OS.
All Revs SP5100
SATA_PCI_config 0x40 [23] = 1
Disable AHCI enhancement.
This feature is not supported. For proper operation, this
feature should be disabled
Note: The system may hang during post if this register is not set correctly.
SATA
X
RTC
7.3
USB
ACPI
SMBUS
X
PM REG
PATA
AC97
HD AUDIO
A-LINK
I/O REG
XIOAPIC
LPC
PCI
For register details, refer to
the sections check-marked
in the SP5100 Register
Reference Guide.
Disabling SATA
ASIC Rev
All Revs SP5100
Register Settings
Function/Comment
Smbus_PCI_config 0xAC [8] = 0
Disables the SATA controller.
This shuts down most clocks in the SATA controller.
Smbus_PCI_config 0xAC [9] = 1
Disables the SATA PHY I2C interface.
This setting is mandatory to prevent un-powered SATA
from corrupting SMbus controller protocol.
Note: Some board designs may choose to disable the SATA controllers to reduce power consumption.
SATA
USB
RTC
ACPI
SMBUS
X
PM REG
PATA
AC97
HD AUDIO
A-LINK
I/O REG
XIOAPIC
2012 Advanced Micro Devices, Inc.
AMD SP5100 Register Programming Requirements
LPC
PCI
For register details refer to
the sections check-marked
in the SP5100 Register
Reference Guide
SATA: dev-17, func-0
Page 54
7.4
Disabling Unused SATA Ports
ASIC Rev
All Revs SP5100
Register Settings
Function/Comment
SATA_PCI_config 0x40 [16] = 1
When set, SATA port0 is disabled, and port0 clock is shut down.
SATA_PCI_config 0x40 [17] = 1
When set, SATA port1 is disabled, and port1 clock is shut down.
SATA_PCI_config 0x40 [18] = 1
When set, SATA port2 is disabled, and port2 clock is shut down.
SATA_PCI_config 0x40 [19] = 1
When set, SATA port3 is disabled, and port3 clock is shut down.
SATA_PCI_config 0x40 [20] = 1
When set, SATA port4 is disabled, and port4 clock is shut down.
SATA_PCI_config 0x40 [21] = 1
When set, SATA port5 is disabled, and port5 clock is shut down.
Note: Some board designs may choose to disable unused SATA ports to reduce power consumption.
SATA
X
RTC
USB
SMBUS
PATA
AC97
HD AUDIO
ACPI
PM REG
A-LINK
I/O REG
XIOAPIC
2012 Advanced Micro Devices, Inc.
AMD SP5100 Register Programming Requirements
LPC
PCI
For register details refer to
the sections check-marked
in the SP5100 Register
Reference Guide
SATA: dev-17, func-0
Page 55
7.5
SATA Subclass Programming Sequence
The SATA controller supports the following modes:
•
•
•
IDE mode
AHCI mode
Raid mode
The SBIOS programs the subclass code and the interface register to enable the SATA controller to
be represented as the IDE controller, the AHCI controller, or the Raid controller.
ASIC Rev
All Revs SP5100
Register Settings
Function/Comment
1. SATA_PCI_config 0x40 [0] = 1
Enables the subclass code register (PCI config register
0Ah) and the program interface register (PCI config
register 09h) to be programmable.
2. Program SATA Controller mode in
a) IDE mode, or
SATA_PCI_config 0x09 = 0x8f (default)
SATA_PCI_config 0x0A = 0x01
The SBIOS is required to program the subclass code
register of the SATA controller to be represented as the
IDE, AHCI, or the RAID controller.
b) AHCI mode, or
SATA_PCI_config 0x09 = 0x01
SATA_PCI_config 0x0A = 0x06
c) RAID mode
SATA_PCI_config 0x09 = 0x00
SATA_PCI_config 0x0A = 0x04
3. SATA_PCI_config 0x40 [0]= 0
SATA
X
RTC
Clears the bit to convert the subclass code register to be a
read-only register.
The SBIOS is required to complete this step to ensure that
the subclass code register be read-only (in order to be PCI
compliant).
USB
SMBUS
PATA
AC97
HD AUDIO
ACPI
PM REG
A-LINK
I/O REG
XIOAPIC
2012 Advanced Micro Devices, Inc.
AMD SP5100 Register Programming Requirements
LPC
PCI
For register details refer to
the sections check-marked
in the SP5100 Register
Reference Guide
SATA: dev-17, func-0
Page 56
7.6
SATA PHY Programming Sequence
The SBIOS needs to program the SATA controllers in the following sequence. Performing this
procedure gives enough time for the SATA controllers to correctly complete SATA drive detection.
The SBIOS needs to do the same procedure after the system resumes back from the S3 state.
Note: This will be added once the silicon comes back for PHY fine tune value.
ASIC Rev
All Revs SP5100
SATA
X
RTC
Register Settings
Function/Comment
1. SATA_PCI_config 0x86 [15:0] = 0x2C00
SATA PHY global setting.
2. SATA_PCI_config 0x88 [31:0] =
0x01B48017
SATA_PCI_config 0x8C [31:0]=
0x01B48019
SATA_PCI_config 0x90 [31:0] =
0x01B48016
SATA_PCI_config 0x94 [31:0] =
0x01B48016
SATA_PCI_config 0x98 [31:0] =
0x01B48016
SATA_PCI_config 0x9C [31:0] =
0x01B48016
SATA GENI PHY ports setting, pre-emphasis setting, and
GENII PHY setting enable setup for port [0~5] This setting
is for the Travelly board. Since its port0 and port1are
eSATA ports, PCI_config 0x88 and 0x8C have different
settings than the rest of the ports. For non-eSATA port, the
setting should be 0x01B48016. For the Shinner board,
SATA_PCI_config 0x88/8C/90/94/98/9C [31:0] =
0x01B48016.
3.SATA_PCI_config 0xA0 [15:0] = 0xA09A
SATA_PCI_config 0xA2 [15:0] = 0xA09F
SATA_PCI_config 0xA4 [15:0] = 0xA07A
SATA_PCI_config 0xA6 [15:0] = 0xA07A
SATA_PCI_config 0xA8 [15:0] = 0xA07A
SATA_PCI_config 0xAA [15:0] = 0xA07A
SATA GEN II PHY port setting for port [0~5]. This setting is
for the Travelly board. Since its port0 and port1 are eSATA
ports, PCI_config 0xA0 and 0xA2 have different settings
than the rest of the ports. For non-esata port, the setting
should be 0xA07A. For the Shinner board,
SATA_PCI_config 0xA0/A2/A4/A6/A8/AA [15:0] = 0xA07A.
USB
SMBUS
PATA
AC97
HD AUDIO
ACPI
PM REG
A-LINK
I/O REG
XIOAPIC
2012 Advanced Micro Devices, Inc.
AMD SP5100 Register Programming Requirements
LPC
PCI
For register details refer to
the sections check-marked
in the SP5100 Register
Reference Guide
SATA: dev-17, func-0
Page 57
7.7
7.7.1
SATA Identification Programming Sequence for IDE Mode
SATA Drive Detection
The following sequence should be included in the SBIOS drive identification loop for SATA drives
detection.
ASIC Rev
All Revs SP5100
Register Settings
1. If any of the SATA port status register
SATA_BAR5 + 0x128 [3:0] = 0x3
SATA_BAR5 + 0x1A8 [3:0] = 0x3
SATA_BAR5 + 0x228 [3:0] = 0x3
SATA_BAR5 + 0x2A8 [3:0] = 0x3
SATA_BAR5 + 0x328 [3:0] = 0x3
SATA_BAR5 + 0x3A8 [3:0] = 0x3
Function/Comment
SATA_BAR5 + 0x128h : port 0 status register
SATA_BAR5 + 0x1A8h : port 1 status register
SATA_BAR5 + 0x228h : port 2 status register
SATA_BAR5 + 0x2A8h : port 3 status register
SATA_BAR5 + 0x328h : port 4 status register
SATA_BAR5 + 0x3A8h : port 5 status register
SATA host and device serial interface communication
is done and ready if the SATA port status register =
0x3.
Then set
SATA_BAR0 + 0x6 = 0xA0 or
SATA_BAR0 + 0x6 = 0xB0 or
SATA_BAR2 + 0x6 = 0xA0 or
SATA_BAR2 + 0x6 = 0xB0 or
PATA_BAR0/2 + 0x6 = 0xA0 or
PATA_BAR0/2 + 0x6 = 0xB0 or
for SATA controller primary master emulation
for SATA controller primary slave emulation
for SATA controller secondary master emulation
for SATA controller secondary slave emulation
for PATA controller primary/secondary master
emulation
for PATA controller primary/secondary slave
emulation
Go to step (2).
Else
Otherwise,
No drive is attached, exit the detection loop.
No SATA drive attached or SATA drive is not ready.
2. If
SATA_BAR0 + 0x6 = 0xA0 and
SATA_BAR0 + 0x7 [7] & [3] = 0
Or
SATA_BAR0 + 0x6 = 0xB0 and
SATA_BAR0 + 0x7[7] & [3] = 0
Or
SATA_BAR2 + 0x6 = 0xA0 and
SATA_BAR2 + 0x7[7] & [3] = 0
Or
SATA_BAR2 + 0x6 = 0xB0 and
SATA_BAR2 + 0x7[7] & [3] = 0
Or
PATA_BAR0/2 + 0x6 = 0xA0 and
PATA_BAR0/2 + 0x7[7] & [3] = 0
Or
PATA_BAR0/2 + 0x6 = 0xB0 and
PATA_BAR0/2 + 0x7[7] & [3] = 0
then the drive detection is completed
SATA_BAR0 + 0x7[7] & [3] = 0 means primary master
device ready
SATA_BAR0 + 0x7[7] & [3] = 0 means primary slave
device ready
SATA_BAR2 + 0x7[7] & [3] = 0 means secondary
master device ready
SATA_BAR2 + 0x7[7] & [3] = 0 means secondary slave
device ready
PATA_BAR0/2 + 0x7[7] & [3] = 0 means primary
/secondary master device ready
PATA_BAR0/2 + 0x7[7] & [3] = 0 means primary
/secondary slave device ready
There is no SATA device attached on the port if time
out occurs (see Note).
Else
loop until 30s time out, drive detection fail
Note: Most drives do not need 10s timeout. The 10s timeout is only needed for some particularly large capacity SATA
drives, which require a longer spin-up time during a cold boot.
2012 Advanced Micro Devices, Inc.
AMD SP5100 Register Programming Requirements
SATA: dev-17, func-0
Page 58
SATA
X
RTC
7.8
USB
SMBUS
PATA
AC97
HD AUDIO
ACPI
PM REG
A-LINK
I/O REG
XIOAPIC
LPC
PCI
For register details refer to
the sections check-marked
in the SP5100 Register
Reference Guide
Restoring SATA Registers after S3 Resume State
The following registers need to be restored by the SBIOS after S3 resume for the SATA controller.
ASIC Rev
All Revs SP5100
Register Settings
Function/Comment
SATA_PCI_config 0x09 [7:0]
SATA_PCI_config 0x0A [7:0]
Programmable interface and Subclass code. To program
the subclass code register, SATA_PCI_config x40[0]
needs to be set. After the subclass is programmed,
SATA_PCI_config 0x40[0] needs to be reset.
SATA_PCI_config 0x44 [0]
Enables the Watch-dog timer for the all ports.
SP5100 A12
SATA_PCI_config 0x40 [29]
Disables the testing/enhancement mode.
SP5100 A12
SATA_PCI_config 0x48 [24]
Disables the testing/enhancement mode.
SP5100 A12
SATA_PCI_config 0x48 [21]
Disables the testing/enhancement mode.
SP5100 A14 and
above
SATA_PCI_config 0x40 [29]
SATA_PCI_config 0x48 [24]
SATA_PCI_config 0x48 [21]
SATA_PCI_config 0x48 [15:9]
Smbus_PCI_config 0xAC [13]
Enables the testing/enhancement mode.
All Revs SP5100
SATA_PCI_config 0x86 [15:0]
SATA_PCI_config 0x88 [24:0]
SATA_PCI_config 0x8C [24:0]
SATA_PCI_config 0x90 [24:0]
SATA_PCI_config 0x94 [24:0]
SATA_PCI_config 0x98 [24:0]
SATA_PCI_config 0x9C [24:0]
SATA_PCI_config 0xA0 [15:0]
SATA_PCI_config 0xA2 [15:0]
SATA_PCI_config 0xA4 [15:0]
SATA_PCI_config 0xA6 [15:0]
SATA_PCI_config 0xA8 [15:0]
SATA_PCI_config 0xAA [15:0]
SATA PHY setting.
All Revs SP5100 SATA_PCI_config 0x34 [7:0]
SATA_PCI_config 0x61 [7:0]
All Revs SP5100
SATA
X
RTC
SATA Capability
SATA BAR5 + 0xF8[17:0]
SATA ports indication registers.
USB
SMBUS
PATA
AC97
HD AUDIO
ACPI
PM REG
A-LINK
I/O REG
XIOAPIC
2012 Advanced Micro Devices, Inc.
AMD SP5100 Register Programming Requirements
LPC
PCI
For register details refer to
the sections check-marked
in the SP5100 Register
Reference Guide
SATA: dev-17, func-0
Page 59
7.9
Internal and External SATA Ports Indication Registers
The following registers need to be programmed for eSATA ports
ASIC Rev
All Revs SP5100
Register Settings
Function/Comment
For the ports which are configured as iSATA
PxCMD.ESP (External SATA Port) and PxCMD.HPCP
ports.
(Hot Plug Capable Port) registers should be programmed
1.PxCMD.ESP should leave as reset default
to indicate if the port is used for External SATA and if it
(logic 0).
requires hot Plug capability.
2.PxCMD.HPCP should be cleared.
To clear the register, write:
Port0: SATA BAR5 + 0xF8[0]=0
Port1: SATA BAR5 + 0xF8[1]=0
Port2: SATA BAR5 + 0xF8[2]=0
Port3: SATA BAR5 + 0xF8[3]=0
Port4: SATA BAR5 + 0xF8[4]=0
Port5: SATA BAR5 + 0xF8[5]=0
For iSATA (internal SATA) port(s), Px.CMD.HPCP and
Px.CMD.ESP should be logic 0.
For the ports which configured as eSATA.
1.PxCMD.ESP should be set.
To set the register, write:
Port0: SATA BAR5 + 0xF8[12]=1
Port1: SATA BAR5 + 0xF8[13]=1
Port2: SATA BAR5 + 0xF8[14]=1
Port3: SATA BAR5 + 0xF8[15]=1
Port4: SATA BAR5 + 0xF8[16]=1
Port5: SATA BAR5 + 0xF8[17]=1
SATA BAR5 + F8[17:12]= 000001(b)
2.PxCMD.HPCP should be cleared.
To clear the register, write:
Port0: SATA BAR5 + 0xF8[0]=0
Port1: SATA BAR5 + 0xF8[1]=0
Port2: SATA BAR5 + 0xF8[2]=0
Port3: SATA BAR5 + 0xF8[3]=0
Port4: SATA BAR5 + 0xF8[4]=0
Port5: SATA BAR5 + 0xF8[5]=0
To program these registers, SATA_PCI_config x40[0]
needs to be set. After the subclass is programmed,
SATA_PCI_config 0x40[0] needs to be reset.
For example, if port 0 was configured as eSATA, other
Ports are iSATA.
SATA BAR5 + F8[5:0] = 000000(b)
PxCMD.ESP bit is mutually exclusive with PxCMD.HPCP
bit in the same port.
In general:
If no E-SATA ports in system then HCAP.SXS=0 else
HCAP.SXS=1.
ESP
HPCP
eSATA (signal only connector)
1
0
iSATA
0
0
PxCMD ESP located at:
SATA BAR5+ port offset + 0x18[21]
PxCMD HPCP located at:
3. If any of the ports is programmed as
External Port, HCAP.SXS should also be
set. To set the register, write:
SATA BAR5 + 0xFC[20]=1
SATA
X
RTC
SATA BAR5+ port offset + 0x18[18]
USB
SMBUS
PATA
AC97
HD AUDIO
ACPI
PM REG
A-LINK
I/O REG
XIOAPIC
LPC
PCI
For register details refer to
the sections check-marked
in the SP5100 Register
Reference Guide
7.10 Aggressive Link Power Management
ALPM controls the HIPM functionality. The ALPM bit is also used by the SATA driver to enable
HIPM and DIPM. Customers should check with the drive vendor to confirm if the SATA device
being used is compatible and functional with HIPM and DIPM capability before enabling the ALPM.
HIPM and DIPM are supported in the SP5100. If the customer requires HIPM / DIPM support and
gets confirmation from the drive vendors that the drivers they are supporting will enable HIPM, then
this feature can be enabled. The following registers need to be programmed to disable the ALPM.
Note: If the ALPM needs to be enabled, the following sequence should NOT be programmed.
2012 Advanced Micro Devices, Inc.
AMD SP5100 Register Programming Requirements
SATA: dev-17, func-0
Page 60
Sequence to disable ALPM:
ASIC Rev
All Revs SP5100
SATA
X
RTC
Register Settings
Function/Comment
1. SATA_PCI_config 0x40 [0] = 1
Unlocks the configuration register so that HBA AHCI
Capabilities Register can be modified.
2. SATA_BAR5 + 0xFC [11] = 0
Clearing this bit has the following effects. The SupportAggressive-Link-Power-Management Capability is hidden
from software in AHCI HBA Capabilities Register. As a
result, software will not enable the HBA to aggressively
enter power-saving (Partial/Slumber) mode.
Once this bit is cleared, SATA BAR5 + 0x00[26] will be 0
3. SATA_PCI_config 0x40 [0]= 0
Clears the bit to lock configuration registers so that AHCI
HBA Capabilities register is read-only.
USB
SMBUS
PATA
AC97
HD AUDIO
ACPI
PM REG
A-LINK
I/O REG
XIOAPIC
LPC
PCI
For register details refer to
the sections check-marked
in the SP5100 Register
Reference Guide
7.11 SATA MSI and D3 Power State Capability
7.11.1 SATA MSI Settings
SATA controller does not support message based interrupts. The capability pointer offset needs
to be re-programmed from its default setting to prevent the driver from enabling this feature.
7.11.2 D3 Power State Settings
SATA controller does not support D3 Power State if S1 is supported. The capability pointer offset
needs to be re-programmed from its default setting to prevent the driver from enabling this
feature.
2012 Advanced Micro Devices, Inc.
AMD SP5100 Register Programming Requirements
SATA: dev-17, func-0
Page 61
7.11.3 Capability Pointer Settings
The following settings re-program the capability pointer to the recommended start of the
capabilities table of supported features (hide MSI, and if S1 is supported, hide D3 state capability
from driver/OS).
ASIC Rev
Register Settings
Function/Comment
All Revs SP5100
1.
2.
3.
SATA_PCI_config 0x40 [0] = 1
SATA_PCI_config 0x61[7:0]=0x70
SATA_PCI_config 0x40 [0] = 0
D3 power state is visible. (If S1 is not supported)
MSI capability for SATA is hidden.
All Revs SP5100
1.
2.
3.
SATA_PCI_config 0x40 [0] = 1
SATA_PCI_config 0x34[7:0]=0x70
SATA_PCI_config 0x40 [0] = 0
D3 power state is hidden. (If S1 is supported)
MSI capability for SATA is hidden.
SATA
x
RTC
USB
SMBUS
PATA
AC97
HD AUDIO
ACPI
PM REG
A-LINK
I/O REG
XIOAPIC
LPC
PCI
For register details, refer to
the sections check-marked
in the SP5100 Register
Reference Guide.
7.12 Disabling CCC (Command Completion Coalescing) Support
ASIC Rev
All Revs SP5100
Register Settings
Function/Comment
1. SATA_PCI_config 0x40 [0] = 1
Unlocks the configuration register so that HBA AHCI
Capabilities register can be modified.
2. SATA_BAR5 + 0xFC [19] = 0
Clearing this bit has the following effects:
Once this bit is cleared, SATA BAR5 + 0x00[7] will be 0
Command Completion Coalescing function will not be
supported.
3. SATA_PCI_config 0x40 [0] = 0
SATA
X
RTC
USB
SMBUS
PATA
AC97
Clears the bit to lock configuration registers so that AHCI
HBA Capabilities register is read-only.
For register details, refer to
the sections check-marked
in the SP5100 Register
ACPI
PM REG
A-LINK
I/O REG
XIOAPIC
Reference Guide.
Register 0xFC[19] controls the CCC capability setting in register BAR5, offset 0 bit 7. Setting it to 0 will make CCC not
visible to software. CCC is enabled by default, on power up. Default. BIOS should leave 0xFC[19] untouched for
normal operation. The setting to disable should only be used if CCC needs to be disabled for specific platform
configuration.
2012 Advanced Micro Devices, Inc.
AMD SP5100 Register Programming Requirements
HD AUDIO
LPC
PCI
SATA: dev-17, func-0
Page 62
8 LPC (bus-0, dev-20, fun-03)
8.1
Enabling/Disabling LPC Controller
ASIC Rev
All Revs SP5100
8.2
SATA
USB
RTC
ACPI
Register Settings
Function/Comment
Smbus_PCI_config 0x64 [20] = 1 (default)
SMBUS
X
PM REG
Enables the LPC controller.
PATA
AC97
HD AUDIO
A-LINK
I/O REG
XIOAPIC
LPC
PCI
For register details refer to
the sections check-marked
in the SP5100 Register
Reference Guide
Parallel Port ECP Mode Support
ASIC Rev
All Revs SP5100
Register Settings
If IO 0x378 & IO 0x778 as ECP (or
ECP+EPP) address port is used:
LPC_PCI_config 0x44 [0] = 1
LPC_PCI_config 0x44 [1] = 1
Function/Comment
For the parallel port to support ECP mode, or ECP+EPP mode,
the SBIOS needs to allocate 2 base addresses for the parallel
port.
base_address_2 = base_address_1 + 0x400
If IO 0x278 & IO 0x678 as ECP (or
ECP+EPP) address port is used:
LPC_PCI_config 0x44 [2] = 1
LPC_PCI_config 0x44 [3] = 1
If IO 0x3BC & IO 0x7BC as ECP (or
ECP+EPP) address port is used:
LPC_PCI_config 0x44 [4] = 1
LPC_PCI_config 0x44 [5] = 1
Base_address_1 is controlled by register bit 0, or bit 2, or bit 4.
Base address_2 is controlled by register bit 1, or bit 3, or bit 5.
The SBIOS needs to enable both base addresses to properly
support ECP (or ECP+EPP) mode.
SATA
USB
SMBUS
PATA
AC97
HD AUDIO
RTC
ACPI
PM REG
A-LINK
I/O REG
XIOAPIC
2012 Advanced Micro Devices, Inc.
AMD SP5100 Register Programming Requirements
LPC
X
PCI
For register details refer to
the sections check-marked
in the SP5100 Register
Reference Guide
LPC (bus-0, dev-20, fun-03)
Page 63
9 IDE Controller (bus-0, dev-20, fun-01)
The SP5100 IDE controller supports single primary channel, even though resources of the
secondary IDE channel are allocated by the in-box driver from the Microsoft operating system.
Therefore the IDE programmable interface (IDE PCI config 0x09 bits [3:2]) is not recommended for
modification.
9.1
Disable Second IDE MSI Capability
ASIC Rev
All Revs SP5100
9.2
Register Settings
IDE PCI_config 0x63 [5]=0
SATA
USB
SMBUS
RTC
ACPI
PM REG
PATA
X
A-LINK
Function/Comment
Hide MSI capability pointer.
AC97
HD AUDIO
I/O REG
XIOAPIC
LPC
PCI
For register details refer to
the sections check-marked
in the SP5100 Register
Reference Guide
Enable IDE Data Bus DD7 Pull-Down Resistor
ASIC Rev
All Revs SP5100
Register Settings
ACPI PMIO2 0xE5 [2] = 1
Function/Comment
Enables IDE data bus DD7 internal pull down resistor at IO
pad. This PD should be enabled whenever IDE controller
enabled.
Note: If the FLASH controller is enabled or IDE DD& has
external PD, then this register should not be set.
Resume from S3 does not require to reset this bit.
SATA
USB
SMBUS
RTC
ACPI
PM REG
PATA
X
A-LINK
AC97
HD AUDIO
I/O REG
XIOAPIC
2012 Advanced Micro Devices, Inc.
AMD SP5100 Register Programming Requirements
LPC
PCI
For register details refer to
the sections check-marked
in the SP5100 Register
Reference Guide
IDE Controller (bus-0, dev-20, fun-01)
Page 64
10 HD Audio (bus-0, dev-20, fun-02)
10.1 Enabling/Disabling HD Audio
ASIC Rev
All Revs SP5100
Register Settings
PM_IO 0x59[3] = 1 (default)
Function/Comment
0 = Disables the HD Audio controller
1 = Enables the HD Audio controller
SATA
USB
SMBUS
PATA
AC97
HD AUDIO
RTC
ACPI
PM REG
x
A-LINK
I/O REG
XIOAPIC
LPC
PCI
For register details refer to
the sections check-marked
in the SP5100 Register
Reference Guide
10.2 HD Audio Interrupt Routing Table
ASIC Rev
All Revs SP5100
SATA
USB
RTC
ACPI
Register Settings
Function/Comment
Smbus_PCI_config 0x63[2:0] = 110 (default) Interrupt routing table for HD Audio:
000 = INTA#
001 = INTB#
010 = INTC#
011 = INTD#
100 = INTE#
101 = INTF#
110 = INTG#
111 = INTH#
SMBUS
X
PM REG
PATA
AC97
HD AUDIO
A-LINK
I/O REG
XIOAPIC
LPC
PCI
For register details refer to
the sections check-marked
in the SP5100 Register
Reference Guide
10.3 Audio Port Configuration
This register controls the selection of ACZ_SDIN0/GPIO42, ACZ_SDIN1/GPIO43,
ACZ_SDIN2/GPIO44, and AZ_SDIN3/GPIO46 pins to function as GPIO, AC97, or HD Audio
signals.
ASIC Rev
All Revs SP5100
Register Settings
Function/Comment
Smbus_PCI_Config_Extend_Reg 0x00[1:0] Port 0 configuration for HD Audio/AC97/GPIO:
= 01 (default)
00 or 11 = GPIO
01 = no function
10 = HD Audio
Note: Port 0 refers to the ACZ_SDIN0/GPIO42 pin.
All Revs SP5100
SMbus_PCI_config_Extend_Reg 0x00[3:2] = Port 1 configuration for HD Audio/AC97/GPIO:
01 (default)
00 or 11 = GPIO
01 = no function
10 = HD Audio
Note: Port 1 refers to the ACZ_SDIN1/GPIO43 pin.
2012 Advanced Micro Devices, Inc.
AMD SP5100 Register Programming Requirements
HD Audio (bus-0, dev-20, fun-02)
Page 65
All Revs SP5100
Smbus_PCI_Config_Extend_Reg 0x00[5:4] Port 2 configuration for HD Audio/AC97/GPIO:
= 10 (default)
00 or 11 = GPIO
01 = no function
10 = HD Audio
Note: Port 2 refers to the ACZ_SDIN2/GPIO44 pin.
All Revs SP5100
Smbus_PCI_Config_Extend_Reg 0x00[7:6] Port 3 configuration for HD Audio/AC97/GPIO:
= 10 (default)
00 or 11 = GPIO
01 = no function
10 = HD Audio
Note: Port 3 is the AZ_SDIN3/GPIO46 pin.
Note: The Smbus_PCI_Config_Extend_Reg are indirectly accessed registers that are accessed through Smbus_PCI_config
xF8 (ExtendedAddrPort) and Smbus_PCI_config xFC (ExtendedDataPort). Refer to the AMD SP5100 Register Reference
Guide, SMBUS section describing the PCI config xF8/FC details.
SATA
USB
RTC
ACPI
SMBUS
X
PM REG
PATA
AC97
HD AUDIO
A-LINK
I/O REG
XIOAPIC
2012 Advanced Micro Devices, Inc.
AMD SP5100 Register Programming Requirements
LPC
PCI
For register details refer to
the sections check-marked
in the SP5100 Register
Reference Guide
HD Audio (bus-0, dev-20, fun-02)
Page 66
Appendix A: Sample Codes for BIOS Workarounds
A1. Sample Code for SP5100 Erratum #11: “Enabling EHCI Dynamic Clock
Gating May Cause Bug Code 0xFE System Error”.
(Refer to section 6.17 “EHCI Dynamic Clock Gating Feature”)
Note: This code is found in the SP5100 BIOS because SP5100 shares the same CIMx as the
SB7xx. It has no relevance for the SP5100 but is included in case it shows up in a software
debugging process.
The programming of the registers in this workaround needs to be done only during S5/S4 to S0
transitions. On resume from S3, these registers are not required to be re-programmed.
;Description:
; This sample code disables ECHI dynamic clock gating feature by clearing bit 12
; in the EHCI BAR (MMIO) Register Offset 0xBC.
;Requirement:
; 1. USB BARs must be programmed before executing this piece of code
; 2. es segment register should be set to base 0 and limit set to 4GB
pushad
;For EHCI controller 1 (Bus 0 Dev 0x12 Fun 2)
;read BAR address
mov eax, 080009210h
mov dx, 0CF8h
out dx, eax
mov dx, 0CFCh
in eax, dx
cmp eax, 0
je EHCI1_BAR_NOT_SET
cmp eax, -1
je EHCI1_BAR_NOT_SET
;enable memory access
mov eax, 080009204h
mov dx, 0CF8h
out dx, eax
mov dx, 0CFCh
in eax, dx
2012 Advanced Micro Devices, Inc.
AMD SP5100 Register Programming Requirements
Appendix A: Sample Codes for BIOS Workarounds
Page 67
or al, 02h
out dx, eax
mov eax, 080009210h
mov dx, 0CF8h
out dx, eax
mov dx, 0CFCh
in eax, dx
mov edi, eax
add edi, 0BCh
mov eax, es:[edi] ;es should be set to 0, and the segment limit should be set 0 to 4GB
and ax, 0EFFFh ;clear BIT12
mov es:[edi], eax
EHCI1_BAR_NOT_SET:
;For EHCI controller 2 (Bus 0 Dev 0x13 Fun 2)
;read BAR address
mov eax, 080009A10h
mov dx, 0CF8h
out dx, eax
mov dx, 0CFCh
in eax, dx
cmp eax, 0
je EHCI2_BAR_NOT_SET
cmp eax, -1
je EHCI2_BAR_NOT_SET
;enable memory access
mov eax, 080009A04h
mov dx, 0CF8h
out dx, eax
mov dx, 0CFCh
in eax, dx
or al, 02h
out dx, eax
2012 Advanced Micro Devices, Inc.
AMD SP5100 Register Programming Requirements
Appendix A: Sample Codes for BIOS Workarounds
Page 68
mov eax, 080009A10h
mov dx, 0CF8h
out dx, eax
mov dx, 0CFCh
in eax, dx
mov edi, eax
add edi, 0BCh
mov eax, es:[edi] ;es should be set to 0, and the segment limit should be set 0 to 4GB
and ax, 0EFFFh ;clear BIT12
mov es:[edi], eax
EHCI2_BAR_NOT_SET:
popad
End of Sample Code ( Erratum # 11)
2012 Advanced Micro Devices, Inc.
AMD SP5100 Register Programming Requirements
Appendix A: Sample Codes for BIOS Workarounds
Page 69
A2. Sample Code for SP5100 Erratum #23: “USB Wake on
Connect/Disconnect with Low Speed Devices”.
(Refer to section 6.2 “USB Device Support to Wake Up System from S3/S4 State”)
The following workaround should be implemented in the platform BIOS to resolve the issue as described
in the SB7x0 Erratum #23.
This routine has to be put in the Sleep trap function.
USBConnectWorkaround PROC NEAR
; testing for EHCI wake event
;jmp $
pushad
; Enabled Support USB Wake-Up event on Resume only
mov
dx, 0cd6h
mov
al, 065h
out
dx, al
inc
dx
in
al, dx
or
al, BIT6
out
dx, al
mov
in
or
out
dx, 824h
ax, dx
ax, bit11
dx, ax
; USB wake-up event.
; Enabled EHCI0 & BAR
mov
dx, (18 shl 3) + 2
mov
ah, 0c4h
call
read_pci_dword_far
and
ebx, 0fffffff0h
call
write_pci_dword_far
mov
call
or
call
ah, 004h
read_pci_dword_far
ebx, 07h
write_pci_dword_far
mov
mov
call
dx, (18 shl 3) + 2
ah, 10h
read_pci_dword_far
call
mov
; EHCI 0
; Set back to D0 state
;
; Enabled IO/Memory/Bus
;
; Get Bar address
; in EBX
USBWorkaroundForConnected
dx, (18 shl 3) + 2
2012 Advanced Micro Devices, Inc.
AMD SP5100 Register Programming Requirements
;
Appendix A: Sample Codes for BIOS Workarounds
Page 70
mov
call
or
call
ah, 0c4h
read_pci_dword_far
ebx, 03h
write_pci_dword_far
; Enabled EHCI1 & BAR
mov
dx, (19 shl 3) + 2
mov
ah, 0c4h
call
read_pci_dword_far
and
ebx, 0fffffff0h
call
write_pci_dword_far
mov
call
or
call
ah, 004h
read_pci_dword_far
ebx, 07h
write_pci_dword_far
mov
mov
call
dx, (19 shl 3) + 2
ah, 10h
read_pci_dword_far
call
mov
mov
call
or
call
; Set to D3 state
; EHCI 1
; Set back to D0 state
;
; Enabled IO/Memory/Bus
;
; Get Bar address
; in EBX
USBWorkaroundForConnected
dx, (19 shl 3) + 2
ah, 0c4h
read_pci_dword_far
ebx, 03h
write_pci_dword_far
;
; Set to D3 state
popad
ret
USBConnectWorkaround ENDP
USBWorkaroundForConnected PROC NEAR
push es
push 0
pop
es
add
ebx, 64h
; Get first USB port
mov
cx, 6
@@:
mov
eax, es:[ebx]
test
eax, BIT13 + BIT0
; Check port empty or not
jnz
SkipWR
or
eax, BIT13
; Set to OHCI
SkipWR:
or
eax, BIT21+ BIT22
; Enabled wake by connected/disconnect
or
es:[ebx], eax
ebx, 4
add
loop
@b
pop
es
ret
USBWorkaroundForConnected ENDP
End of Sample code (Erratum # 23)
2012 Advanced Micro Devices, Inc.
AMD SP5100 Register Programming Requirements
Appendix A: Sample Codes for BIOS Workarounds
Page 71
Appendix B: Revision History
Date
Revisions
Description
July, 2012
3.02
•
Added new section 6.22 Disable Async QH Cache.
Dec 22, 2011
3.01
•
•
•
Updated section 2.4 C-State and VID/FID Change.
Added new section 2.6 MTC1e and FID VID Setting.
Updated section 3.2 SPI Bus.
Nov, 2010
3.00
•
•
Released as public version.
Updated section 2.4 C-State and VID/FID Change: Added stutter time info for
different conditions.
Modified/combined previous section 2.26 and 2.27 to remove support for ASF, but
indicating that SMBUS 1 can still be used as a master for SMBUS devices.
Removed previous section 2.34 PM_TURN_OFF_MSG during ASF Shutdown.
Merged previous section 2.42 Automatic Stutter Timer into section 2.5 Enable C1e
Stutter Timer and Limit Link Disconnect to < 20 ms.
Added section 2.40 Programmable Interrupt Controller Arbitration.
Added section 2.41 HPET MSI Setting.
Added section 2.42 SMAF Matching Setting.
Updated section 6.19 USB Controller DMA Read Delay Tolerant.
Added Disable AHCI enhancement to section 7.2 SATA Initialization.
Updated section 7.11 SATA MSI and D3 Power State Capability to include that
SATA MSI capability is not supported.
Update section 9.1 Disable Second IDE MSI Capability.
•
•
•
•
•
•
•
•
•
•
Sep 11, 2009
2.13
•
•
•
July15, 2009
2.12
•
•
•
•
•
•
•
•
•
June 04, 2009
2.11
•
•
•
•
•
General edits.
Corrected section 7.4 “SATA Power Saving”
•
•
•
2.10
Removed section 1.2 “Feature List”.
Updated section 2.5 “Enable C1e Stutter Timer and Limit Link Disconnect to < 20
ms”
Added section 2.6 “C1e Exit on Assertion of IDLE Exit# (for A15 Only)”.
Added section 2.7 “Support for Entering C1e on HALT# Message (for a15 Only)”.
Updated section 2.32 “Alternate Pin for 14 MHz Clock Input”.
Added section 2.40 “Supporting IDLE_EXIT# from CPU”.
Added section 2.41 “Supporting HALT Message to Generate C1e”.
Added section 2.42 “Automatic Stutter Timer”.
Removed previous section 7.12 “Flash Controller” and section 7.13 “Restoring FC
Registers after S3 Resume State”.
Updated section 2.4 “C-State and VID/FID Change” to cover new generation CPU.
Added new section 2.5 “Enable C1e Stutter Timer to Limit Link Disconnect to < 16
ms”
Updated section 6.2 “USB Device Support to Wake Up System from S3/S4 State”.
Moved section 6.17.1 “Sample Code for the Workaround Described in SB7xx
Erratum #11” into new Appendix A.
Section 7.2 “SATA Initialization”: Added a new setting to the end of the table.
Removed original section 7.4 “SATA Power Saving” since the block level power
saving function in SB7x0 is built-in and the register SMBUS_0xAC[13] is not for
this purpose.
Updated section 7.9 “Internal and External SATA Ports Indication Registers”:
Added description of internal SATA (iSATA) port(s).
Added new Appendix A: Sample Codes for BIOS Workarounds.
•
•
April 29, 2009
Changed heading of section 2.36 from “SMBUS Write Sequence” to “SMBUS
Sequence” implying it now applies to both Read and Write. Also added
recommended time out of 1 ms or greater.
Updated section 2.38 Unconditional Shutdown - clarified how to write to register
Added new section 2.43 LDT_PWRGD De-assertion with SLP_S3#.
2012 Advanced Micro Devices, Inc.
AMD SP5100 Register Programming Requirements
Appendix B: Revision History
Page 72
April 27, 2009
2.09
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Feb 09, 2009
2.08
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Added ASIC revision A15 settings.
General replacement of “A14” with “A14 and above”.
Section 2.4 “C-State and VID/FID Change “: Updated description for PM_IO 0x8B.
Section 2.16 ”PCIe Native Mode”: Changed setting from 1 to 0 for PM_IO
0x84[1]; added suggested settings.
Updated section 2.20 “IMC Access Control”
Updated section 2.28 “Revision ID”.
Added new section 2.34 “Software Clock Throttle Period”.
Added new section 2.35 “Unconditional Shutdown”.
Added new section 2.36 “Watchdog Timer Resolution”
Updated section 4.16 “SMI IO Write”.
Added new section 4.17 “Reset CPU on Sync Flood”.
Added new section 4.18 “Enabling Posted Pass Non-Posted Downstream”.
Added new section 4.19 “Enabling Posted Pass Non-Posted Upstream”.
Added new section 4.20 “64-bit Non-posted Memory Write”.
Updated new section 6.20 “Async Park Mode”.
Added new section 6.24 “USB PID_Error_Checking”.
Updated section 7.9 “Restoring SATA Registers after S3 Resume State” with 2
new settings for SATA Capability.
Section 7.10 “External SATA Ports Indication Registers”: Added definition of
HCAP.SXS and Set Px.CMD.HPCP=0 for iSATA.
Changed title of section 7.12 from “SATA MSI Capability” to “SATA MSI and D3
Power State Capability” and updated the section.
Updated section 2.4, “C-State and VID/FID Change”: Distinguished StutterTime
for Family 10h and non-10h CPUs.
Updated section 2.13, “Legacy DMA Pre-fetch Enhancement”: Added 2 new
settings.
Updated section 2.16, “PCIE Native Mode”: Changed setting for PM_IO 0x84 [1]
from 0 to 1.
Updated section 2.28, “Revision ID”: Corrected applicable ASIC revision to A12
and added Rev ID for A14.
Added section 2.29, “Alternate Pin for 14 MHz Clock Input”.
Added section 2.30, “Gevent2 as GPIO.”
Added section 2.31, “PM_TURN_OFF_MSG during ASF Shutdown.”
Added section 2.32, “SMBUS Block Write Filtering.”
Added section 4.15, “Selecting LPC FRAME# Assertion Timing Power-up.”
Updated section 4.5, “OHCI Prefectch Settings.”
Updated section 6.1, “Enabling/Disabling OHCI and EHCI Controllers“ to correct
the ECHI Enable bit assignments.
Updated section 6.10, “OHCI MSI Function Setting”: Corrected heading, and
corrected applicable ASIC Revision to “All Revs SP5100”
Updated section 6.11: “EHCI Advance Asynchronous Enhancement”: Added A14
setting for enabling AEE function.
Updated section 6.15, “EHCI Async Park Mode”: Added settings for enabling
async park mode for A14.
Added section 6.17.1”Sample Code for the Workaround Described in SB7xx
Erratum #11 (ERN # ERA12011).
Added sections 6.18-6.23.
Updated section 7.1, “Enabling SATA.”
Added section 7.2, “SATA Initialization.”
Updated section 7.3, “Disabling SATA.”
Added section 7.4, “SATA Power Saving.”
Updated section 7.9, “Restoring SATA Registers after S3 Resume State”:
Updated applicable ASIC revisions for various register settings.
Updated section 7.11, “Aggressive Link Power Management.”
Updated section 7.12, “SATA MSI Capability”:
Updated section 7.13, “Flash Controller” by adding a note to indicate FC is not
supported at platform level.
Added section 7.15, “Disabling CCC (Command Completion Coalescing)
Support”:
Updated section 9.1, “Disabling IDE MSI Capability”: Added setting for making
MSI capability visible.
2012 Advanced Micro Devices, Inc.
AMD SP5100 Register Programming Requirements
Appendix B: Revision History
Page 73
September 11, 2008
2.07
•
•
•
•
•
•
•
•
•
•
March 05, 2008
1.02
•
•
February 08, 2008
1.01
•
1.00
Updated section 2.9: Enabling IRQ1/12 Filtering by updating the description for
register setting Smbus_PCI_config 0x62 [1:0].
Added section 6.15: EHCI Async Park Mode.
•
Updated section 2.15: PCIe Native Mode by updating the descriptions and adding
registers to the PCIe Native Mode table.
Added section 2.16: Hardware Monitor.
Added section 2.17: Cir Interrupt Config.
Added section 2.18: SM Pci Config.
Added section 2.19: IMC Access Control
Added section 2.20: CPU Reset.
Added section 3: LPC Controller (bus-0, dev-20, fun-3).
Updated section 4.15: SMI IO Write by changing the title of this section and by
updating the register description.
Added section 7.8: External SATA Ports Indication Registers.
•
Initial OEM release.
•
•
•
•
•
•
•
May 07, 2007
Replaced codename SB700S with SP5100 throughout the document.
Added section 2.2: Unblocked SMI command port.
Replaced previous section 2.9: Enabling IRQ1/12 Filtering with new section 2.10:
Interrupt Routing/Filtering.
Removed previous section 2.28: Reverting USBCLK/14M_25M_48M_OSC Back
to A11 Mode.
Added new section 2.29: SMBus Write Sequence.
Updated section 4.12: Enabling AB and BIF Clock Gating. Changed setting for
ABCFG 0x54[24] to 0.
Added section 6.16: MSI Feature in USB 2.0 Controller.
Added section 6.17, EHCI Dynamic Clock Gating Feature.
Added section 7.9: Disabling Aggressive Link Power Management.
Added section 7.10: Disabling SATA MSI Capability.
2012 Advanced Micro Devices, Inc.
AMD SP5100 Register Programming Requirements
Appendix B: Revision History
Page 74