MODEL 82 SW NEW PRODUCT 1/4” Diameter Sealed Switch ELECTRICAL Input Voltage, Maximum Slider Current, Maximum Insulation Resistance, Minimum Contact Resistance, Maximum Contact Timing Switch Type 16 Vdc 100mA or within rated power, whichever is less 10 Megohms 2 Ohms Non-shorting Single Pole / Double Throw (SPDT) ENVIRONMENTAL Seal Operating Temperature Range Thermal Shock Moisture Resistance Shock, 6ms Sawtooth Vibration Rotational Life Resistance to Solder Heat 85°C Fluorinert® (No Leaks) –55°C to +125°C 5 cycles, –55°C to +125°C Ten 24 hour cycles 100G’s 20G’s, 10 to 2,000 Hz 200 cycles 260°C for 10 sec. MECHANICAL Stop Strength Torque, Starting Maximum Weight, Nominal 5 oz.-in. 3 oz.-in. (0.021 N-m) .02 oz. (0.60 grams) Fluorinert® is a registered trademark of 3M Company. Specifications subject to change without notice. Last Update: 06/24/02. 9 9-3 Model 82 SW TOP ADJUSTMENT (Inch/mm) Model 82PSW, 82PFSW Model Dim. A .25 Min. 6.35 .625 Min. 15.875 82PSW 82PFSW .025 0.635 (1) .10 2.54 .011 Min. 0.28 A .140 Max. 3.556 Standoffs .250 ± .015 Dia. 6.350 ± 0.381 (3) (2) 90° ±5° Housing Metal .10 2.54 .025 ± .005 .110 ± .005 Long X 0.635 ± 0.127 2.794 ± 0.127 Terminal Pins (3) Solderable .017 ± .003 Dia. 0.432 ± 0.076 Wide X .035 ± .005 Deep Slot 0.889 ± 0.127 Note: Model 82PSW dimensions applicable to all models except as noted. Model 82MSW .10 2.54 .10 2.54 (1) (3) .17 4.32 .18 Min. 4.57 (2) .10 2.54 Model 82WSW .10 2.5 .18 4.57 Min. (1) (2) .21 5.3 .020 Min. 0.51 Standoffs (3) .10 2.5 9-4 Model 82 SW SIDE ADJUSTMENT (Inch/mm) Model 82PASW .17 4.32 .10 2.54 .25 Min. 6.35 .185 ± .015 4.669 ± 0.381 .36 9.14 .205 ± .015 5.207 ± 0.381 Housing: Metal Case: Plastic .012 Min. 0.305 (3) .28 7.11 (2) .10 2.54 (1) .035 0.889 Model No. And Resistance Value marked on this surface .10 2.54 PACKAGING Standard: Boxes Capacity Option: 50 Units (82PASW, 82PFSW) 100 Units (All other styles) Tubes All units oriented with #1 pin to same side. Magazine Option: = = Pin Style Width Height Length Capacity = = = = PASW 0.28” 0.94” 15.6” 50 Units PSW,MSW,WSW 0.34” 0.65” 27.5” 100 Units Tape & Reel, Ammo Pack (Available for 82WSW Only) All units oriented with #1 pin to the right of the direction of feed. Tape Reel Ammo Seat Plane to Centerline of Sprocket Hole Width Sprocket Capacity Diameter Tape Fold Box = = = = = = = .71” (18.03 mm) 18 mm Single Hole .50” spacing 1,000 Units 14” (356 mm) 12” (305 mm) 1.5” x 13” x 10” 9 9-5 Model 82 SW ORDERING INFORMATION Standard: 82 P SW Model Series Pin Style Option: Switch Designator 82 W SW TB Pin Style Packaging Option: TB = Tubes (Pin styles PSW, PASW, MSW, WSW) Option: 82 W F SW TR Pin Style Pin Style Suffix: (Used with AP and TR packaging options. Applicable to pin styles WSW only. "F" designates 0.60" lead length.) CIRCUIT DIAGRAM NOTES Metric equivalents, based on 1 inch = 25.4mm are rounded to the same number of significant figures as in the original English units and are provided for general information only. (2) (1) CCW Packaging Option: AP = Ammo pack TR = Tape & Reel (Pin styles WSW, XSW only) CW (3) INCH mm Tolerances unless otherwise specified: Linear = ± .01 inches (.25mm) Angular = ± 2 degrees 9-6 Model 82 SW