HM69 Electrical / Environmental • • • • • Operating Temperature Range Temperature Rise, Maximum Ambient Temperature, Maximum Insulation System Operating Frequency -40°C to +125°C 40°C 80°C Class F, 155°C Up to 3MHz High Current Low Profile Surface Mount Inductors S RomHpliant Co Specifications Inductance 100kHz, 0.1V @ 0 Adc @ Irated (nH ± 20%) (nH) Typ. Min. Typ. Part Number HM69-10R025LF HM69-20R050LF HM69-30R070LF HM69-40R10LF HM69-50R10LF HM69-50R15LF HM69-55R10LF HM69-55R20LF HM69-60R10LF HM69-60R15LF HM69-60R20LF HM69-70R30LF HM69-75R20LF HM69-80R30LF Notes: 25 50 70 100 100 150 100 200 100 150 200 300 200 300 18 28 50 60 72 96 64 140 69 104 144 200 150 216 25 36 67 75 95 120 80 175 87 130 180 250 175 285 (1) DCR (mW) Typ. Max. 0.27 0.20 0.40 0.31 0.40 0.40 0.45 0.45 0.42 0.42 0.42 0.17 0.40 0.17 (2) Irated @ 25°C (Adc) 0.33 0.24 0.48 0.39 0.48 0.48 0.56 0.56 0.50 0.50 0.50 0.20 0.50 0.25 (4) Heating (3) Current (A) 42 70 46 28 29 18 45 21 68 48 31 37 20 40 22 35 25 25 24 24 25 25 31 31 31 70 40 76 Core Loss Factor K1 K2 3.847E-14 1.074E-13 1.074E-13 7.124E-14 8.733E-14 8.733E-14 1.337E-13 1.337E-13 2.311E-13 2.311E-13 2.311E-13 6.784E-13 3.559E-13 9.107E-13 59.444 50.117 70.164 156.891 127.990 191.986 96.541 160.902 52.336 78.503 104.671 98.921 134.203 72.674 (1) DC resistance is measured at 25°C. (2) The rated current (Irated) is the current at which the inductance will be decreased by 20% from its initial (zero DC) value. (3) The heating current is the DC current, which causes the component temperature to increase by approximately 40°C. This current is determined by soldering the component on a typical application PCB, and then applying the device for 30 minutes. (4) Core Loss approximation is based on published core data: Core Loss = K1 * (f)1.77 * (K2∆I)2.21 Where: core loss in watt f = switching frequency in kHz K1 and K2 = core loss factor ∆I = delta I across the component in Amp. K2∆I = one half of the peak to peak flux density across the component in Gauss Packaging Standard: Embossed Tape & Reel Reel: Diameter: Capacity: Case size 10,40 Case size 20,30,60 Case size 50,55,75 Case size 70,80 = 13” (330.2mm) = 1000 Units = 800 Units = 500 Units = 350 Units Ordering Information Model Series Case Size HM69 - 50 R10 LF TR13 Inductance Code: First 2 digits are significant. Last digit denotes the number of trailing zeros. For values below 10µH, “R” denotes the decimal point. www.bitechnologies.com Lead-Free TR - Tape & Reel Packing 13 - 13” reel 2009/10 EDITION MAGNETIC COMPONENTS SELECTOR GUIDE We reserve the right to change specifications without prior notice. 79 Outline Dimensions (mm) Top View Case Size 10 20 30 40 50 55 60 70 75 80 A 6.00 7.50 7.00 7.01 8.60 8.60 10.2 13.5 13.5 13.8 Recommended Solder Pad Layout Bottom View B 5.00 6.50 7.00 6.35 6.30 6.30 7.00 13.0 13.0 13.0 C 3.00 5.00 5.00 3.30 3.30 4.80 5.10 6.80 3.50 8.20 D 1.00 1.50 1.50 1.50 1.50 1.50 1.50 3.00 2.00 2.00 E 1.50 2.95 2.30 2.85 2.85 2.85 2.50 5.00 2.50 5.00 F 1.60 3.00 2.50 3.20 3.20 3.20 2.80 5.30 3.20 5.30 G 2.00 2.50 2.50 2.50 2.50 2.50 5.50 5.50 7.00 5.50 H 5.80 7.50 7.50 7.50 9.00 9.00 10.5 13.5 13.5 13.8 Electrical Characteristics @ 25°C 80 MAGNETIC COMPONENTS SELECTOR GUIDE 2009/10 EDITION We reserve the right to change specifications without prior notice. www.bitechnologies.com Electrical Characteristics @ 25°C (Cont’d) www.bitechnologies.com 2009/10 EDITION MAGNETIC COMPONENTS SELECTOR GUIDE We reserve the right to change specifications without prior notice. 81