FPM-2150 Series User Manual

FPM-2150 Series
Flat Panel Monitor with
15" Color TFT/LCD Display
User Manual
Copyright Notice
This document is copyrighted by Advantech Co., Ltd. All rights are
reserved. Advantech Co., Ltd. reserves the right to make improvements to
the products described in this manual at any time. Specifications are thus
subject to change without notice.
No part of this manual may be reproduced, copied, translated, or transmitted in any form or by any means without the prior written permission of
Advantech Co., Ltd. Information provided in this manual is intended to
be accurate and reliable. However, Advantech Co., Ltd., assumes no
responsibility for its use, nor for any infringements upon the rights of
third parties which may result from its use.
All brand and product names mentioned herein are trademarks or registered trademarks of their respective holders.
This Manual Covers the Following Models
• FPM-2150GB
Part No. 2003215002
3rd Edition
Printed in Taiwan
May 2005
FPM-2150 Series User Manual
ii
Product Warranty (1 year)
Advantech warrants to you, the original purchaser, that each of its products will be free from defects in materials and workmanship for one year
from the date of purchase.
This warranty does not apply to any products which have been repaired or
altered by persons other than repair personnel authorized by Advantech,
or which have been subject to misuse, abuse, accident or improper installation. Advantech assumes no liability under the terms of this warranty as
a consequence of such events.
All defective products under normal / standard operation will be serviced
by Advantech’s global RMA system. If an Advantech product is defective, it will be repaired or replaced at no charge during the warranty
period. For out-of-warranty repairs, you will be billed according to the
cost of replacement materials, service time and freight. Please consult
your dealer for more details.
If you think you have a defective product, follow these steps:
1.
Collect all the information about the problem encountered. (For
example, CPU speed, Advantech products used, other hardware
and software used, etc.) Note anything abnormal and list any
onscreen messages you get when the problem occurs.
2.
Call your dealer and describe the problem. Please have your manual, product, and any helpful information readily available.
3.
If your product is diagnosed as defective, obtain an RMA (return
merchandize authorization) number from your dealer. This allows
us to process your return more quickly.
4.
Carefully pack the defective product, a fully-completed Repair and
Replacement Order Card and a photocopy proof of purchase date
(such as your sales receipt) in a shippable container. A product
returned without proof of the purchase date is not eligible for warranty service.
5.
Write the RMA number visibly on the outside of the package and
ship it prepaid to your dealer.
iii
FCC Class B
This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential environment. This
equipment generates, uses and can radiate radio frequency energy. If not
installed and used in accordance with this user's manual, it may cause
harmful interference to radio communications.
Note that even when this equipment is installed and used in accordance
with this user’s manual, there is still no guarantee that interference will
not occur. If this equipment is believed to be causeing harmful interference to radio or television reception, this can be determined by turning
the equipment on and off. If the interference is occurring, the user is
encouraged to try to correct the interference by one or more of the following measures:
• Reorient or relocate the receiving antenna
• Increase the separation between the equipment and the receiver
• Connect the equipment to a power outlet on a circuit different from that
to which the receiver is connected
• Consult the dealer or an experienced radio/TV technician for help
FPM-2150 Series User Manual
iv
Packing List
Before installing your equipment, make sure that the following materials
have been received:
• FPM-2150 Series flat panel monitor
• Accessory pack, including:
- AC/DC adapter
- AC/DC power adapter bracket
- Video signal cable, 1.8m
- Fixed panel-mounted bracket x 10 pcs
- Screw Bags (M4x25 mm screws x 10 pcs)
- DC in Power Cord bracket x 1 piece
- RS-232 cable, 1.8m (FPM-2150-R only)or
USB cable, 1.8m (FPM-2150-U only)
- Driver/manual CD-ROM
If any of these items are missing or damaged, contact your distributor or
sales representative immediately.
Additional Information and Assistance
1. Visit the Advantech web site at www.advantech.com where you can
find the latest information about the product.
2. Contact your distributor, sales representative, or Advantech's customer service center for technical support if you need additional assistance. Please have the following information ready before you call:
• Product name and serial number
• Description of your peripheral attachments
• Description of your software (operating system, version, application
software, etc.)
• A complete description of the problem
• The exact wording of any error messages
Safety Instructions
1. Read these safety instructions carefully.
2. Keep this User's Manual for later reference.
v
3. Disconnect this equipment from any AC outlet before cleaning. Use a
damp cloth. Do not use liquid or spray detergents for cleaning.
4. For plug-in equipment, the power outlet socket must be located near
the equipment and must be easily accessible.
5. Keep this equipment away from humidity.
6. Put this equipment on a reliable surface during installation. Dropping
it or letting it fall may cause damage.
7. The openings on the enclosure are for air convection. Protect the
equipment from overheating. DO NOT COVER THE OPENINGS.
8. Make sure the voltage of the power source is correct before connecting the equipment to the power outlet.
9. Position the power cord so that people cannot step on it. Do not place
anything over the power cord.
10. All cautions and warnings on the equipment should be noted.
11. If the equipment is not used for a long time, disconnect it from the
power source to avoid damage by transient overvoltage.
12. Never pour any liquid into an opening. This may cause fire or electrical shock.
13. Never open the equipment. For safety reasons, the equipment should
be opened only by qualified service personnel.
14. If one of the following situations arises, get the equipment checked
by service personnel:
a. The power cord or plug is damaged.
b. Liquid has penetrated into the equipment.
c. The equipment has been exposed to moisture.
d. The equipment does not work well, or you cannot get it to work
according to the user's manual.
e. The equipment has been dropped and damaged.
f. The equipment has obvious signs of breakage.
15. DO NOT LEAVE THIS EQUIPMENT IN AN UNCONTROLLED
ENVIRONMENT WHERE THE STORAGE TEMPERATURE IS
BELOW -20° C (-4° F) OR ABOVE 60° C (140° F). THIS MAY
DAMAGE THE EQUIPMENT.
The sound pressure level at the operator's position according to IEC 7041:1982 is no more than 70dB(A).
FPM-2150 Series User Manual
vi
DISCLAIMER: This set of instructions is given according to IEC 704-1.
Advantech disclaims all responsibility for the accuracy of any statements
contained herein.
Wichtige Sicherheishinweise
1. Bitte lesen sie Sich diese Hinweise sorgfältig durch.
2. Heben Sie diese Anleitung für den späteren Gebrauch auf.
3. Vor jedem Reinigen ist das Gerät vom Stromnetz zu trennen. Verwenden Sie Keine Flüssig-oder Aerosolreiniger. Am besten dient ein
angefeuchtetes Tuch zur Reinigung.
4. Die NetzanschluBsteckdose soll nahe dem Gerät angebracht und
leicht zugänglich sein.
5. Das Gerät ist vor Feuchtigkeit zu schützen.
6. Bei der Aufstellung des Gerätes ist auf sicheren Stand zu achten. Ein
Kippen oder Fallen könnte Verletzungen hervorrufen.
7. Die Belüftungsöffnungen dienen zur Luftzirkulation die das Gerät vor
überhitzung schützt. Sorgen Sie dafür, daB diese Öffnungen nicht
abgedeckt werden.
8. Beachten Sie beim. AnschluB an das Stromnetz die AnschluBwerte.
9. Verlegen Sie die NetzanschluBleitung so, daB niemand darüber fallen
kann. Es sollte auch nichts auf der Leitung abgestellt werden.
10. Alle Hinweise und Warnungen die sich am Geräten befinden sind zu
beachten.
11. Wird das Gerät über einen längeren Zeitraum nicht benutzt, sollten
Sie es vom Stromnetz trennen. Somit wird im Falle einer Überspannung eine Beschädigung vermieden.
12. Durch die Lüftungsöffnungen dürfen niemals Gegenstände oder Flüssigkeiten in das Gerät gelangen. Dies könnte einen Brand bzw. elektrischen Schlag auslösen.
13. Öffnen Sie niemals das Gerät. Das Gerät darf aus Gründen der elektrischen Sicherheit nur von authorisiertem Servicepersonal geöffnet
werden.
14. Wenn folgende Situationen auftreten ist das Gerät vom Stromnetz zu
trennen und von einer qualifizierten Servicestelle zu überprüfen:
a - Netzkabel oder Netzstecker sind beschädigt.
vii
b - Flüssigkeit ist in das Gerät eingedrungen.
c - Das Gerät war Feuchtigkeit ausgesetzt.
d - Wenn das Gerät nicht der Bedienungsanleitung entsprech
end funktioniert oder Sie mit Hilfe dieser Anleitung keine
Verbesserung erzielen.
e - Das Gerät ist gefallen und/oder das Gehäuse ist beschädigt.
f - Wenn das Gerät deutliche Anzeichen eines Defektes aufweist.
Der arbeitsplatzbezogene Schalldruckpegel nach DIN 45 635 Teil
1000 beträgt 70dB(A) oder weiger.
15. VOSICHT: Explisionsgefahr bei unsachgemaben Austausch der Batterie.Ersatz nur durch densellben order einem vom Hersteller empfohlenemahnlichen Typ. Entsorgung gebrauchter Batterien navh Angaben des
Herstellers.
16. ACHTUNG: Es besteht die Explosionsgefahr, falls die Batterie auf
nicht fachmännische Weise gewechselt wird. Verfangen Sie die Batterie
nur gleicher oder entsprechender Type, wie vom Hersteller empfohlen.
Entsorgen Sie Batterien nach Anweisung des Herstellers.
Der arbeitsplatzbezogene Schalldruckpegel nach DIN 45 635 Teil 1000
beträgt 70dB(A) oder weiger.
Haftungsausschluss: Die Bedienungsanleitungen wurden entsprechend
der IEC-704-1 erstellt. Advantech lehnt jegliche Verantwortung für die
Richtigkeit der in diesem Zusammenhang getätigten Aussagen ab.
DISCLAIMER: This set of instructions is given according to IEC704-1.
Advantech disclaims all responsibility for the accuracy of any statements
contained herein.
FPM-2150 Series User Manual
viii
Contents
Chapter
1 Introduction ..................................................... 2
1.1
1.2
1.3
1.4
1.5
1.6
Chapter
Introduction ....................................................................... 2
Specifications .................................................................... 2
LCD Specifications ........................................................... 3
Power Adapter Specifications ........................................... 4
Connectors......................................................................... 4
Dimensions........................................................................ 5
Figure 1.1:FPM-2150GB Chassis Dimensions .............. 5
2 System Setup.................................................... 8
2.1
Mounting FPM-2150......................................................... 8
2.1.1
2.1.2
2.1.3
2.2
Wall Mounting ............................................................... 8
Figure 2.1:Wall Mounting ............................................. 8
Panel Mounting .............................................................. 9
Figure 2.2:Panel Mounting ............................................ 9
Rack Mounting .............................................................. 9
Figure 2.3:Rack Mounting ............................................. 9
Desktop, Swing-ARM for FPM-2150............................. 10
2.2.1
2.2.2
2.2.3
Desktop Stand .............................................................. 10
Figure 2.4:Desktop Stand for the FPM-2150 Series .... 10
Swing-ARM (designed for VESA ARM standard) ..... 11
Figure 2.5:Swing-ARM for the FPM-2150 series ....... 11
Power Adapter ............................................................. 12
Appendix A Display Timing Mode & OSD ...................... 14
A.1
Supported Input Timing Modes ...................................... 14
A.2
A.3
A.4
Keypad Interface ............................................................. 15
Power Indicator LED Status............................................ 15
OSD Function.................................................................. 16
Table A.1:Supported Input Formats ............................ 14
Appendix B Touchscreen ................................................... 18
B.1
B.2
B.3
B.4
Introduction ..................................................................... 18
Touchscreen Specifications............................................. 18
Installing Driver for Windows 2000/XP ......................... 19
Configuring PenMount Windows 2000/XP Driver......... 24
B.5
Uninstall the PenMount Windows 2000/XP driver......... 36
B.4.1
B.4.2
B.4.3
PenMount Control Panel ............................................. 24
PenMount Monitor Menu Icon .................................... 34
PenMount Rotating Functions ..................................... 35
ix
Table of Contents
FPM-2150 Series User Manual
x
CHAPTER
1
2
Introduction
This chapter includes:
• Introduction
• Specifications
• LCD Specification
• Power Consumption
• Connectors
• Dimensions
Chapter 1 Introduction
1.1 Introduction
Advantech's FPM-2150 Series consists of 15" color TFT LCD flat panel
monitors built specifically for industrial applications. With the optional
touchscreen, the FPM-2150 Series is an user-friendly system control
interface.
In addition to its usual application as an LCD panel monitor, the FPM2150 Series comes standard with Direct VGA control signal input, making it compatible with industrial PCs and workstations.
The OSD (On Screen Display) function allows you to adjust the display
and turn the backlight on and off, a function that is highly appreciated
among experienced users of industrial flat panel monitors.
The whole chassis is made of durable steel, and the front panel is of AlMg with NEMA4/IP65 compliance.
Products in the FPM-2150 Series can also be provided in touch screen
versions (FPM-2150-R and FPM-2150-U). With an 8-wire resistive type
touchscreen, this monitor can be immediately transformed into a remote
control system.
The Advantech FPM-2150 is the ultimate HMI solution for your industrial application.
1.2 Specifications
General
• Construction: Heavy-duty steel chassis
• Front Panel: Al-Mg, NEMA4/IP65 compliant
• Control: OSD (On Screen Display) control pad on front side
• Mounting: Panel, wallmount, rackmount (with rackmount kit), desktop
or VESA Arm
• Dimensions (W x H x D): 383 x 307 x 48.13 mm (15" x 12.09" x 1..9")
• Panel Mount Cut out Dimension (W x H): 373.5 x 297.5 mm (14.7" x
14.71")
• Weight: 4.5 kg (9.9 lb)
FPM-2150 Series User Manual
2
• Vibration (operating): 5 ~ 17 Hz, double-amplitude displacement; 17
~ 500 Hz, 1.0 G peak to peak
• CE, FCC, BSMI, CCC certified
• Power Consumption: +12V +/- 10% @ 2.5 A
Touchscreen (Optional)
• Type: 8 wire, analog resistive
• Resolution: 1024 x 1024
• Light Transmission: 75% (Gouge Hardness is greater than 4H per
ASTM D3363-92 for HCC01, HCG10 and HCG12)
• Controller: RS-232 interface (for FPM-2150G-R version) or USB 1.1
(for FPM-2150G-U version)
• Power Consumption:
FPM-2150G-R: +5 V @ 200 mA
FPM-2150G-U: +5 V @ 100 mA (USB bus power)
• OS Support: Windows 95/98/NT/2000/XP/CE 4.2, MS-DOS,
• Life Span: 1,000,000 activations (typical) at a single point with a 5/8"
diameter silicone finger with a 350g load at 2 touches per second
1.3 LCD Specifications
• Display Type: XGA TFT- LCD
• Display Size: 15"
• Max. Colors: 262 k
• Max. Resolution: 1024 x 768
• Viewing Angle: 140 ° (H), 120 ° (V)
• Luminance: 250 cd/m2
• Storage Temperature: -20 ~ 60 °C (-4 ~ 140 °F)
• Operating Temperature: 0 ~ 50 °C (32 ~ 122 °F)
• Contrast Ratio: 500 : 1 (typ)
• Lamp Life Time (MTBF): 40,000 hrs.
3
Chapter 1
1.4 Power Adapter Specifications
• Max Output Power: 42 Watts
• AC input voltage: 100 - 240 V AC
• Output voltage: + 12 V @ 3.5 A
• Safety Standards: UL/CE/CCC/TUV/CB
1.5 Connectors
The following connectors are on the bottom of the FPM-2150 Series:
VGA Port (DB15)
This DB-15 connector can be connected to the system via the external 15pin DB-15 connector locatd on the left side of the system unit.
RS-232 Touchscreen Connector (DB9) (with FPM-2150G-R)
This connector will only be present if a touchscreen is installed. It must
be connected to the RS-232 port of the PC. The touchscreen cable is
included with all orders that include the touchscreen option.
USB Touchscreen Connector (USB type B) (with FPM-2150G-U)
This connector will only be present if a touchscreen is installed. It must
be connected to the USB port of the PC. The touchscreen cable is
included with all orders that include the touchscreen option.
DC 12V Power In
This connector connects to the DC 12V Switching Power Supply.
Warning:
Before you connect a VGA cable between FPM-2150 and a PC, please
note the following issues.
1. If you have installed a operating system in the PC, make sure the vertical frequency is within the acceptable range. (Refer to Appendix B)
2. If you have not installed a operating system, you have to adjust the
vertical frequency to fall within the range.
FPM-2150 Series User Manual
4
1.6 Dimensions
Figure 1.1: FPM-2150GB Chassis Dimensions
5
Chapter 1
FPM-2150 Series User Manual
6
CHAPTER
2
2
System Setup
• Mounting the Monitor
• Wall / Panel / Rack Mounting
• Desktop / Swing-Arm Mounting
Chapter 2 System Setup
2.1 Mounting FPM-2150
The FPM-2150 Series can be flexibly mounted. The versatility of the
FPM-2150 mounts enable it to be mounted on your desk or almost anywhere else.
2.1.1 Wall Mounting
Please refer to figure 2.1 and follow the steps below to install FPM-2150
on a wall. The wall mounting kit is optional. (P/N: FPM-2150DESK-MT)
1. Screw the hook and wall-mounted brackets on the wall.
2. Place the FPM-2150 in the bracket.
3. Fix FPM-2150 on the hook and the wall-mounted bracket
Hook Bracket
Wall-mounting Bracket
Figure 2.1: Wall Mounting
FPM-2150 Series User Manual
8
2.1.2 Panel Mounting
Refer to figure 2.2 and follow the instructions below to install in a panel.
1.
Place ten panel-mounting brackets on FPM-2150 (3 on the top, 3
on the bottom, 2 on the left, and 2 on the right).
2.
Fasten the ten panel-mounting brackets with screws.
3.
Mount FPM-2150 on the panel by the screws on the ten panelmounted brackets.
Figure 2.2: Panel Mounting
2.1.3 Rack Mounting
Refer to figure 2.3. FPM-2150 can be directly mounted in a standard 19"
rack. Just mount the panel on the rack and secure with four screws. The
rack mounting kit is optional. (P/N: FPM-2150RACK-MT).
Figure 2.3: Rack Mounting
9
Chapter 2
2.2 Desktop, Swing-ARM for FPM-2150
The FPM-2150 can also be mounted in other ways. You can use the desktop stand for desktop use or attach it on a swing-arm bracket.
2.2.1 Desktop Stand
Refer to figure 2.4. The desktop stand bracket is attached to the rear of
FPM-2150.. Simply attach the small bracket at the rear side of the monitor by screwing the two screws. The bracket now becomes the desktop
stand bracket.
The desktop stand kit is optional. (P/N: FPM-2150DESK-MT)
Figure 2.4: Desktop Stand for the FPM-2150 Series
FPM-2150 Series User Manual
10
2.2.2 Swing-ARM (designed to meet VESA ARM standard)
75
100
FPM-2150 has been designed with support for the VESA arm standard.
Refer to figure 2.5. Detach the mounting brackets on the rear side, then
attach the FPM-2150 onto the VESA ARM mount.
Figure 2.5: Swing-ARM for the FPM-2150 series
11
Chapter 2
2.2.3 Power Adapter
The power adapter bracket is attached to the rear of FPM-2150. Detach
the small bracket at the rear side of the monitor by unscrewing the four
screws.
FPM-2150 Series User Manual
12
A
APPENDIX
2
Display Timing Mode
and OSD
Appendix A Display Timing Mode & OSD
A.1 Supported Input Timing Modes
The different frequencies below are already programmed in this module,
and the synchronous signal inputs are automatically recognized.
Table A.1: Supported Input Formats
Vertical Frequencies
Resolution
56 Hz
640 x 480
60 Hz
70 Hz
Yes
720 x 400
800 x 600
72 Hz
75 Hz
Yes
Yes
Yes
Yes
Yes
Yes
1024 x 768
Yes
Yes
Yes
Yes
Note 1: Even if the preset timing is entered, some adjustment of functions such as Horizontal period, CLK-delay and display position,
are required. The adjusted values are memorized in every preset
number.
Note 2: This module recognizes the synchronous signals with near preset
timing of the frequency of the HS and Vsync, even in the case
that the signals other than the preset timing that were entered.
Note 3: Because adjustments may not fit, such as differing magnifying
ratios or, in the case that you use it except for the display timing
that was preset.
FPM-2150 Series User Manual
14
A.2 Keypad Interface
AUTO
Press this button to execute auto-adjustment process.
SEL
Press to show the OSD screen or select an item to change
its setting.
Press to move between items or increase/decrease item setting.
Press both buttons simultanously to lock/unlock the current
settings.
EXIT
Press to close the selected item or the whole OSD screen.
ON/OFF
Press the ON/OFF button to turn FPM-2150G’s backlight on
and off. When power is off, the power indicator will be blinking.
A.3 Power Indicator LED Status
The keypad interface provides a driver for a dual color LED to indicate
status.
(1) Green: COMMON board detects a input signal and sends output signal to LCD panel.
(2) Orange: No signal detected, or out of range.
(3) Green and blinking: Backlight is off.
(3) No color: Power off
15
Appendix A
A.4 OSD Function
Each selected value is stored into LCD memory after SEL signal input or
time out. The stored values are not affected if the power is turned off. But
the selected value is not available in case a selected mode is changed
before time out or power is turned off before time out.
The default definition of input keys is shown as following:
Main Menu Sub Menu
Functionality
Brightness
Adjust brightness of the display
Contrast
Position
Contrast
Adjust contrast of RGB channel
simultanously
Sub Contrast RGB
Adjust color of selected RGB channel
H.Size
Adjust phase of ADC sample clock
Clock Phase
Adjust number of clocks per line
H.Position
Move input image capture window
left or right
V.Position
Move the input image capture window up or down
Information
Information
System input mode information and
maximum range supported by screen
All Reset
All Reset
Reset menu parameters to factory
default setting
FPM-2150 Series User Manual
16
APPENDIX
B
2
Touchscreen
This appendix contains information on
the touchscreen, its installation and
configuration.
Appendix B Touchscreen
B.1 Introduction
The FPM-2150 Series’ optional touchscreen uses advanced 3M™ 8-wire
resistive technology. It provides more accurate sensing capacity than
other technologies. The touchscreen is specially designed for tough
industrial environments, and has been approved to FCC Class B standards.
B.2 Touchscreen Specifications
Electrical
• Contact bounce: < 10 ms
• Operating voltage: 5 V (typical)
• Sheet Resistance: 350 +/- 22% Ω per Square.
• Linearity: <1.5% full scale linearity error in either direction.
• Insulation Resistance: >20 MΩ @ 25 V DC
Durability
• Test conditions: 4 H hardness, 0.04" stylus pen, 350 gram load
• Point activation:
1 Million activations on a single point with a 5/8" diameter silicone
finger with a 350g load at 2 Hz
• Character Activation Life:
>100,000 characters written within a 20 mm x 20 mm area on the touch
screen.
• Chemical resistance:
Hard coating is highly resistant to most solvents and chemicals
FPM-2150 Series User Manual
18
Optical
• Visible light transmission: 75% typical (>74% @ 550 nm test)
• Clarity: Clear Finish - 25%, Antiglare Finish - 15%
Sensor board
• Chemical strengthened glass with 4 H hardness standard.
(Test condition: ASTM D3363-92A)
Ball drop test
• Able to bear a 225 g steel ball dropped from 660 mm elevation without
breaking
Environmental Specifications
• Operating Temperature Range: -20° C ~ +50° C, 2 weeks at 50° C /
90% RH.
• Storage Temperature High: +70° C, 240 hours at ambient humidity.
• Storage Temperature Low: -40° C, continuous at ambient humidity.
• Accelerated Aging: 100 hours at 60° C / 95% RH.
• Thermal Shock: 25 cycles (one cycle is 30 min. dwell alternating from
-40 to +85° C with less than 10 min. transfer time.
B.3 Installing Driver for Windows 2000/XP
The touchscreen has drivers for Windows 2000 and Windows XP. You
should read the instructions in this chapter carefully before you attempt
installation.
Note 1:
The following windows illustrations are examples
only. You must follow the flow chart instructions
and pay attention to the instructions which then
appear on your screen.
Note 2:
Install the HMI CD Driver into the system
CD-ROM (D:\ means CD-ROM)
19
Appendix B
Before installing the Windows 2000/XP driver software, you must have
the Windows 2000/XP system installed and running on your computer.
If you have an older version of the PenMount Windows 2000/XP driver
installed in your system, please remove it first. Follow the steps below to
install the PenMount Windows 2000/XP driver.
1.
When the system first detects the controller board, a screen appears
that shows “Unknown Device.” Do not use this hardware wizard.
Press Cancel.
2.
FPM-2150G-R
Insert the Driver CD-ROM. Go to:
\TouchScreen-DRV\Penmont 9000(resistive)\Windows 2000-XP
Driver\. Click setup.exe.
FPM-2150G-U
Insert the Driver CD-ROM. Go to:
\TouchScreen-DRV\Penmount USB\Windows Driver\. Click
setup.exe.
FPM-2150 Series User Manual
20
3.
The screen displays the installation wizard for the PenMount software. Click “Next”.
21
Appendix B
4.
A License Agreement appears. Click “I accept…” and “Next”
5.
The “Ready to Install the Program” screen appears. Select “Install.”
FPM-2150 Series User Manual
22
6.
The next screen is “Hardware Installation.” Select “Continue Anyway.”
7.
The “InstallShield Wizard Completed” appears. Click “Finish.”
23
Appendix B
B.4 Configuring PenMount Windows 2000/XP Driver
Upon rebooting, the computer automatically finds the new 9000 controller board. The touch screen is connected but not calibrated. Follow the
procedures below to carry out calibration.
1.
After installation, click the PenMount Monitor icon “PM” in the
menu bar.
2.
When the PenMount Control Panel appears, click “Calibrate.”
B.4.1 PenMount Control Panel
The functions of the PenMount Control Panel are Calibrate, Draw, Multiple Monitors, Option, and About, which are explained in the following
sections.
Calibrate
This function offers two ways to calibrate your touch screen. ‘Standard
Calibration’ adjusts most touch screens. ‘Advanced Calibration’ adjusts
aging touch screens.
Standard
Calibration
Click this button and arrows appear pointing to red
squares. Use your finger or stylus to touch the red
squares in sequence. After the fifth red point calibration
is complete. To skip, press ‘ESC’.
Advanced
Calibration
Advanced Calibration uses 4, 9, 16 or 25 points to effectively calibrate touch panel linearity of aged touch
screens. Click this button and touch the red squares in
sequence with a stylus. To skip, press ‘ESC’.
FPM-2150 Series User Manual
24
NOTE:
The older the touch screen, the more
Advanced Mode calibration points you need for
an accurate calibration. Use a stylus during
Advanced Calibration for greater accuracy.
25
Appendix B
FPM-2150 Series User Manual
26
Plot Calibration Data
Check this function and a touch panel linearity comparison graph appears when you have finished
Advanced Calibration. The blue lines show linearity
before calibration and black lines show linearity after
calibration.
27
Appendix B
Draw
Tests or demonstrates the PenMount touch screen operation. The display
shows touch location. Click Draw to start. Touch the screen with your
finger or a stylus and the drawing screen registers touch activity such left,
right, up, down, pen up, and pen down.
Touch the screen with your finger or a stylus and the drawing screen registers touch activity such left, right, up, down, pen up, and pen down.
Click Clear Screen to clear the drawing.
FPM-2150 Series User Manual
28
Multiple Monitors
Multiple Monitors supports from two to six touch screen displays for one
system. The PenMount drivers for Windows 2000/XP support Multiple
Monitors. This function supports from two to six touch screen displays
for one system. Each monitor requires its own PenMount touch screen
control board, either installed inside the display or in a central unit. The
PenMount control boards must be connected to the computer COM ports
via the RS-232 interface. Driver installation procedures are the same as
for a single monitor. Multiple Monitors supports the following modes:
Windows Extend Monitor Function
Matrox DualHead Multi-Screen Function
nVidia nView Function
NOTE:
The Multiple Monitors function is for use with
multiple displays only. Do not use this function
if you have only one touch screen display.
Please note once you turn on this function the
Rotating function is disabled.
Enable the multiple display function as follows:
1.
Check the Enable Multiple Monitor Support box; then click
Map Touch Screens to assign touch controllers to displays.
29
Appendix B
2.
When the mapping screen message appears, click OK.
3.
Touch each screen as it displays “Please touch this monitor.” Following this sequence and touching each screen is called mapping
the touch screens.
FPM-2150 Series User Manual
30
4.
Touching all screens completes the mapping and the desktop reappears on the monitors.
5.
Select a display and execute the ‘Calibration’ function. A message
to start calibration appears. Click OK.
6.
“Touch this screen to start its calibration” appears on one of the
screens. Touch the screen.
7.
“Touch the red square” messages appear. Touch the red squares in
sequence.
8.
Continue calibration for each monitor by clicking Standard Calibration and touching the red squares.
31
Appendix B
NOTE:
1. If you used a single VGA output for multiple
monitors, please do not use the Multiple Monitors
function. Just follow the regular procedure for
calibration on each of your desktop monitors.
2. The Rotating function is disabled if you use the
Multiple Monitors function.
3. If you change the resolution of display or
screen address, you have to redo Map Touch
Screens so the system understands where the
displays are.
Option
This panel function supports two modes—Operation Mode and Beep
Sound Mode—which allow configuration for specific touch screen applications, such as point-of-sales (POS) terminals.
Operation
Mode
This mode enables and disables the mouse’s ability to
drag on-screen icons—useful for configuring POS terminals.
Stream Mode – Select this mode and the mouse functions as normal and allows dragging of icons.
Point Mode – Select this mode and the mouse only provides a click function, and dragging is disabled.
Beep
Sound
Mode
Enable Beep Sound – turns beep function on and off
Beep on Pen Down – beep occurs when pen comes
down
Beep on Pen Up – beep occurs when pen is lifted up
Beep on both of Pen Down/Up – beep occurs on both
Beep Frequency – modifies sound frequency
Beep Duration – modifies sound duration
FPM-2150 Series User Manual
32
About
This panel displays information about the PenMount controller and driver
version.
33
Appendix B
B.4.2 PenMount Monitor Menu Icon
The PenMount monitor icon (PM) appears in the menu bar of Windows
2000/XP system when you turn on PenMount Monitor in PenMount Utilities.
PenMount Monitor has the following functions.
Beep
Turns beep on or off.
Right
Button
When you select this function, a mouse
icon appears in the right-bottom of the
screen. Click this icon to switch between
Right and Left Button functions.
Pen Stabilizer
Check this function to reduce cursor vibration for relatively
unstable touch screens, or where there may be excess
vibration. Normally this function is not checked.
Exit
Exits the PenMount Monitor function.
FPM-2150 Series User Manual
34
B.4.3 PenMount Rotating Functions
The PenMount driver for Windows 2000/XP supports several display
rotating software packages. Please see Chapter 5 for more information.
The PenMount drivers for Windows 95, Windows 98/Me, Windows
2000/XP, as well as Windows 98 USB and Windows Me/2000/XP support display rotating software packages such as:
• Portrait’s Pivot Screen Rotation Software
• ATI Display Driver Rotate Function
• nVidia Display Driver Rotate Function
• SMI Display Driver Rotate Function
• Intel 845G/GE Display Driver Rotate Function
Configuring the Rotate Function
1.
Install the rotation software package.
2.
Choose the rotate function (0°, 90°, 180°, 270°) in the 3rd party
software. The calibration screen appears automatically. Touch this
point and rotation is mapped.
NOTE:
The Rotate function is disabled if you use Monitor
Mapping
35
Appendix B
B.5 Uninstall the PenMount Windows 2000/XP driver
1.
Exit the PenMount monitor (PM) in the menu bar.
2.
Go to Settings, then Control Panel, and then click Add/Remove
program. Select PenMount DMC9000 and click the Add/Remove
button.
3.
Select PenMount DMC9000 and DMC9100. Click the Remove
button.
4.
Select ‘Yes’ and “Close” to remove the PenMount Windows 2000/
XP driver, and reboot the system.
FPM-2150 Series User Manual
36