Sony Optiarc DVD/CD-Rewritable Drive Product Specification Model

Sony Optiarc
DVD/CD-Rewritable Drive
Product Specification
Model: AD-7717H-01
FW Revision: 1.00
Drive Specification
Confidential
Revision 0.90
Jul 7, 2010
Sony Optiarc Inc.
Planned by
N.Yamada
Authorized by H.Sano
Products Business Group
Business Div.2
Sony Optiarc Inc. Confidential
Sony Optiarc Super Multi Drive Specification AD-7717H-01 Specification Rev. 0.90
1/25
TABLE OF CONTENTS
1.0 INTRODUCTION AND SCOPE............................................................................................................................................. 4
2.0 APPLICABLE DOCUMENTS................................................................................................................................................ 4
3.0 PRODUCT DEFINITION........................................................................................................................................................ 5
3.1 GENERAL ........................................................................................................................................................................... 5
3.2 PRODUCT DESCRIPTION ................................................................................................................................................ 5
4.0 PERFORMANCE AND FUNCTIONAL REQUIREMENTS................................................................................................. 6
4.1 SUMMARY OF STANDARD PERFORMANCE .............................................................................................................. 6
4.1.1 DVD MEDIUM............................................................................................................................................................. 6
4.1.2 CD MEDIUM................................................................................................................................................................ 6
4.2 PERFORMANCE REQUIREMENTS................................................................................................................................. 7
4.2.1 DVD MODES AND BLOCK LENGTH SUPPORTED............................................................................................... 7
4.2.1.1 DVD READABLE FORMAT, MODES AND BLOCK LENGTH SUPPORTED ....................................... 7
4.2.1.2 DVD WRITABLE FORMAT, MODES AND BLOCK LENGTH SUPPORTED ........................................ 7
4.2.2 DVD WRITE METHOD SUPPORTED....................................................................................................................... 7
4.2.3 DVD WRITABLE MEDIA........................................................................................................................................... 7
4.2.4 CD MODES AND BLOCK LENGTH SUPPORTED.................................................................................................. 8
4.2.4.1 CD READABLE FORMAT, MODES AND BLOCK LENGTH SUPPORTED .......................................... 8
4.2.4.2 CD WRITABLE FORMAT, MODES AND BLOCK LENGTH SUPPORTED ........................................... 8
4.2.5 CD WRITE METHOD SUPPORTED.......................................................................................................................... 8
4.2.6 CD WRITABLE MEDIA.............................................................................................................................................. 8
4.2.7 TRANSFER RATE ....................................................................................................................................................... 8
4.2.7.1 READ SPEED AND TRANSFER RATE...................................................................................................... 8
4.2.7.2 WRITE SPEED AND TRANSFER RATE.................................................................................................... 9
4.2.8 SERIAL ATA INTERFACE BURST RATE.............................................................................................................. 10
4.2.9 ROTATION SPEED ................................................................................................................................................... 10
4.2.9.1 DVD MEDIUM........................................................................................................................................... 10
4.2.9.2 DVD-RAM (VERSION 1) .......................................................................................................................... 10
4.2.9.3 DVD-RAM (VERSION 2) .......................................................................................................................... 10
4.2.9.4 CD MEDIUM .............................................................................................................................................. 10
4.2.10 ACCESS TIME (INCLUDING LATENCY)............................................................................................................ 10
4.2.10.1 DVD MEDIUM......................................................................................................................................... 10
4.2.10.2 CD MEDIUM ............................................................................................................................................ 11
4.2.10.3 DVD-RAM MEDIUM............................................................................................................................... 11
4.2.11 SPIN UP AND TRAY EJECT TIME ....................................................................................................................... 11
4.2.12 USER ERROR RATES............................................................................................................................................. 11
4.2.13 MPC3 COMPLIANCE.............................................................................................................................................. 11
4.2.14 FLASH ROM UPDATE ........................................................................................................................................... 11
4.2.15 DVD CONTENT SCRAMBLE SYSTEM AUTHENTICATION............................................................................ 11
4.2.16 REGION PLAYBACK CONTROL.......................................................................................................................... 11
4.2.17 MAXIMUM PLAYBACK SPEED........................................................................................................................... 12
4.2.18 TOLERANCE PERTAINING TO MEDIA .............................................................................................................. 12
5.0 ENVIRONMENTAL ............................................................................................................................................................. 13
5.1 TEMPERATURE (NON-CONDENSING) ....................................................................................................................... 13
5.1.1 NON-OPERATING .................................................................................................................................................... 13
5.1.2 OPERATING .............................................................................................................................................................. 13
5.2 HUMIDITY........................................................................................................................................................................ 13
5.2.1 NON-OPERATING .................................................................................................................................................... 13
5.2.2 OPERATING .............................................................................................................................................................. 13
5.3 VIBRATION...................................................................................................................................................................... 13
5.3.1 NON-OPERATING .................................................................................................................................................... 13
5.3.2 OPERATING .............................................................................................................................................................. 13
5.4 SHOCK .............................................................................................................................................................................. 13
5.4.1 NON-OPERATING .................................................................................................................................................... 13
5.4.2 OPERATING .............................................................................................................................................................. 14
5.5 VIBRATION AND DROP (PACKAGED) ....................................................................................................................... 14
5.5.1 VIBRATION (PACKAGED)...................................................................................................................................... 14
5.5.2 DROP (PACKAGED)................................................................................................................................................. 14
6.0 QUALITY AND RELIABILITY........................................................................................................................................... 15
6.1 COSMETIC........................................................................................................................................................................ 15
6.2 DISC LOADER MECHANISM LIFE............................................................................................................................... 15
6.3 MTBF................................................................................................................................................................................. 15
6.4 OPTICAL PICKUP ACTUATOR MECHANISM............................................................................................................ 15
6.5 MTTR (MEAN TIME TO REPAIR) ................................................................................................................................. 15
Sony Optiarc Inc. Confidential
Sony Optiarc Super Multi Drive Specification AD-7717H-01 Specification Rev. 0.90
2/25
6.6 ELECTROSTATIC DISCHARGE SUSCEPTIBILITY (ESD)......................................................................................... 15
6.7 PRODUCTION FINAL TEST........................................................................................................................................... 15
7.0 REGULATIONS AND STANDARDS ................................................................................................................................. 16
7.1 SAFETY APPROVAL....................................................................................................................................................... 16
7.2 EMC AND COMPLIANCE............................................................................................................................................... 16
7.3 FDA COMPLIANCE......................................................................................................................................................... 16
7.4 RoHS COMPLIANCE ....................................................................................................................................................... 16
7.5 WHQL................................................................................................................................................................................ 16
8.0 SOUND POWER OUTPUT (ACOUSTIC NOISE) .............................................................................................................. 16
9.0 MECHANICAL ..................................................................................................................................................................... 18
9.1 DIMENSIONS AND MOUNTING ORIENTATION ....................................................................................................... 18
9.1.1 DIMENSIONS ............................................................................................................................................................ 18
9.1.2 MOUNTING ORIENTATION ................................................................................................................................... 18
9.1.3 WEIGHT ..................................................................................................................................................................... 18
9.1.4 FORCE RECOMMENDED VALUE RANGE ON TOP COVER ............................................................................. 19
9.2 MATERIAL & COLOR..................................................................................................................................................... 19
9.2.1 EJECT BUTTON, FRONT BEZEL............................................................................................................................ 19
9.2.2 TRAY.......................................................................................................................................................................... 19
9.2.3 ACTIVITY LED ......................................................................................................................................................... 19
9.3 INTERFACE CONNECTOR............................................................................................................................................. 19
9.4 DISC LOADING MECHANISM ...................................................................................................................................... 19
9.4.1 EJECT BUTTON ........................................................................................................................................................ 20
9.4.2 EMERGENCY EJECT................................................................................................................................................ 20
9.4.3 EJECT COMMAND ................................................................................................................................................... 20
9.5 LABELING ON A DRIVE ................................................................................................................................................ 20
10.0 ELECTRICAL ..................................................................................................................................................................... 21
10.1 POWER............................................................................................................................................................................ 21
10.1.1 VOLTAGE ................................................................................................................................................................ 21
10.1.1.1 VOLTAGE TOLERANCE......................................................................................................................... 21
10.1.1.2 RIPPLE AND NOISE TOLERANCE ....................................................................................................... 21
10.1.2 CURRENT ................................................................................................................................................................ 21
10.2. SERIAL ATA INTERFACE........................................................................................................................................... 22
10.2.1 GENERAL ................................................................................................................................................................ 22
10.2.2 ELECTORICAL........................................................................................................................................................ 22
10.2.2.1 CONNECTOR PIN DIFINITION ............................................................................................................. 22
10.2.2.2 SIGNAL CHARACTERITICS.................................................................................................................. 23
10.2.3 COMMANDS ........................................................................................................................................................... 23
10.2.3.1 GENERAL................................................................................................................................................. 23
10.2.3.2 TASK FILE COMMANDS ....................................................................................................................... 23
10.2.3.3 PACKET COMMANDS............................................................................................................................ 23
10.3 DATA BUFFER............................................................................................................................................................... 24
10.4 AUDIO SIGNAL INTERFACE ...................................................................................................................................... 24
11.0 PACKAGING ...................................................................................................................................................................... 24
Appendix: Revision History
Figure 1: Mechanical Drawing (Attached Sheet of Paper)
Sony Optiarc Inc. Confidential
Sony Optiarc Super Multi Drive Specification AD-7717H-01 Specification Rev. 0.90
3/25
1.0 INTRODUCTION AND SCOPE
This document contains information for OEM customer to purchase the internal bare DVD/CD-Rewritable drive model
AD-7717H-01 that is 12.7mm height form factor with a Serial ATA interface. This drive unit is capable to write
DVD-RAM (Ver2) discs, DVD+R discs, DVD+R Double Layer (DVD+R DL) discs, DVD+RW discs, DVD-R discs,
DVD-R Dual Layer (DVD-R DL) discs, DVD-RW discs, CD-R discs and CD-RW discs, and also has the same function
as ordinary DVD-ROM drive. This drive unit has 5x ZCLV Speed DVD-RAM writing, 8x CAV speed DVD+R and
DVD-R writing, 6x ZCLV speed DVD+R DL and DVD-R DL writing, 8x ZCLV speed DVD+RW writing, 6x ZCLV
speed DVD-RW writing, 24x CAV speed CD-R writing and 24x ZCLV speed CD-RW writing, 8x CAV speed
DVD-ROM reading and 24x CAV speed CD-ROM reading capabilities, and supports various DVD and CD formats.
This drive unit has a drawer type disc loading mechanism. This drive unit is designed to be mounted and used in the
horizontal and vertical orientation. This drive unit has Busy LED.
2.0 APPLICABLE DOCUMENTS
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
N/A
Optiarc AD-7717H ATAPI/IDE (SATA) Command Set Specification
CD-Audio "Red Book" Reference (Reference Only)
CD-ROM "Yellow Book" Reference (Reference Only)
CD-ROM XA Reference (Reference Only)
CD-I "Green Book" Reference (Reference Only)
CD-WO "Orange Book, Part 2" Reference (Reference Only)
CD-RW "Orange Book, Part 3" Reference (Reference Only)
Video CD "White Book" Reference (Reference Only)
CD-TEXT "Red Book" Reference (Reference Only)
ATAPI CD-ROM specification: SFF-8020i Rev 2.6 (Reference only)
DVD Specifications for Read-Only Disc Ver 1.0 August 1996 (Reference Only)
DVD Specifications for Recordable Disc for General Ver 2.0 May 2000 (Reference Only)
DVD Specifications for Re-recordable Disc Ver 1.2 December 2003 (Reference Only)
DVD Specifications for Re-recordable Disc for Dual Layer Part1 Ver 1.9 Nov. 29 2005 (Reference Only)
DVD-RAM Part1 Physical Specifications Version 2.2 (Reference Only)
DVD +R 4.7Gbytes Basic Format Specifications Ver 1.2 July 2003 (Reference Only)
DVD+R 8.5Gbytes Basic Format Specifications Version 1.0 March 2004 (Reference Only)
DVD +ReWritable 4.7Gbytes Basic Format Specifications Ver 1.2 December 2002 (Reference Only)
ANSI Document, AT Attachment with Packet Interface -8 Volume1-3 (ATA/ATAPI-7) T13/1532D Rev.4b
SFF80.91iv5 Rev.1.4: Mt. Fuji Commands for Multimedia Devices
ANSI Document, SCSI Multimedia Commands -5 (MMC-5) T10/1675D
T10/1363D Rev.10g November 12, 2001
MMC4 T10/1545-D Rev.3d
Serial ATA: International Organization Serial ATA Rev3.0
Sony Optiarc Inc. Confidential
Sony Optiarc Super Multi Drive Specification AD-7717H-01 Specification Rev. 0.90
4/25
3.0 PRODUCT DEFINITION
3.1 GENERAL
This drive unit is compatible of play DVD-ROM, DVD+R, DVD+R DL, DVD+RW, DVD-R, DVD-R DL,
DVD-RW, DVD-RAM (Ver.2), CD-Audio, CD-ROM (Mode 1 and mode 2), CD-ROM XA (Mode 2, form 1 and
form 2), Photo CD (Single and multiple sessions), CD Extra, CD-text, CD-R and CD-RW discs. This drive unit can
play CD-I (FMV) and VIDEO CD with special function. This drive unit can also play DVD-Video with special
function, such as MPEG decoder. This drive unit can operate in 3.3-8x CAV (Constant Angular Velocity) speed at
reading DVD-ROM data and10-24x CAV speed at reading CD-ROM for data tracks. This drive unit supports
writing modes and methods as below.
5x ZCLV speed DVD-RAM (Ver.2) writing
: Random and Sequential.
8x CAV speed DVD+R writing, 8x ZCLV speed DVD+RW writing and 6x ZCLV speed DVD+R DL writing
: Random, Sequential and Multi-Session.
8x CAV speed DVD-R writing, 6x ZCLV speed DVD-RW writing and 6x ZCLV speed DVD-R DL writing
: Disc at Once, Incremental, and Multi-Border. Restricted overwrite (DVD-RW only)
24x CAV speed CD-R writing and 24x ZCLV speed CD-RW writing
: Disc at Once, Track at Once, Session at Once Variable size Packets and Fixed size Packets.
This drive unit is designed with a sealed construction to ensure dust free operation. This drive unit accepts a standard
CD or DVD disc using a drawer loading and unloading, and can operate in both the horizontal and vertical
orientation. This drive unit is designed to be used inside the host PC. This drive unit communicates with the host PC
through the Serial ATA interface.
3.2 PRODUCT DESCRIPTION
This drive unit has an optical pickup head, servo electronics to maintain correct focus, tracking, feed position, radial
tilt and spindle speed, digital electronics to recover the recorded data and provide error correction in Mode 1 and
Mode 2 Form 1 to the maximum capabilities of the CD-ROM ECC, and a Serial ATA interface to the host computer.
This drive unit has hardware layered error correction (LECC) for the main channel data of the CD-ROM. This drive
unit also provides error correction of the DVD-Video and DVD-ROM. This device supports 3.3-8x CAV speed for
DVD-ROM data tracks transfer rate of 11MBytes/sec. (Outside track) and 10-24x CAV speed for data tracks with a
sustained mode 1 data transfer rate of 3600KBytes/sec. (Outside track), respectively. The Serial ATA controller has
a 2Mbytes data buffer, and insures that in all cases a full block of data is transferred at the designated data transfer
rate on the Serial ATA bus as specified in section 10.2. As for the drive, it is equipped with the buffer under run
protection feature in writing.
A 13 pin connector is located at the back of the drive unit. A more detailed description of the connectors and eject
mechanism is included in the mechanical section (Section 9) of this document.
This drive unit is designed to be mounted inside of a host PC enclosure. This drive unit has Busy LED. The front
bezel of this drive unit has a manual eject button and emergency pin hole.
The applicable media are DVD+R (Single and Double Layer), DVD-R (Single and Dual Layer), DVD+RW,
DVD-RW, DVD-RAM (Ver.2), DVD (Single and Dual Layer), CD, CD-ROM, CD-R and CD-RW (MS, HS, US
and US+) discs. Alternatively, any standard CD-Audio disc is playable and compatible with this drive. These discs
shall conform to optical and mechanical standards as set forth in the DVD, RED, YELLOW and ORANGE (Part 2,
3) BOOK.
Sony Optiarc Inc. Confidential
Sony Optiarc Super Multi Drive Specification AD-7717H-01 Specification Rev. 0.90
5/25
4.0 PERFORMANCE AND FUNCTIONAL REQUIREMENTS
4.1 SUMMARY OF STANDARD PERFORMANCE
Below is a brief summary of performance and functional specifications as set forth by the standards cited above to
be used as quick reference.
4.1.1 DVD MEDIUM
USER DATA CAPACITY
(1 Gbytes = 10E9 bytes)
4.7 Gbytes
8.54 Gbytes
1.46 Gbytes
2.66 Gbytes
Single layer
Dual layer
Single layer
Dual layer
12cm
12cm
8cm
8cm
USER DATA/BLOCK
2048 Bytes
ADDRESS DESCRIPTION
Block
RECORDING SURFACES
1 or 2
RECORDING LAYER
Single or Dual
DISC DIAMETER
120 mm or 80 mm
DISC CENTER HOLE
15 mm diameter
THICKNESS
1.2mm (0.6mm x 2)
TRACK PITCH
0.74 microns, typical
SCANNING VELOCITY
3.49 m/sec
3.84 m/sec
ROTATION SPEED
1388 to 574 rpm (Normal Speed) Varies over radius
Single layer (Normal Speed)
Dual layer (Normal Speed)
4.1.2 CD MEDIUM
The following specification marked with an * is a calculated and practical maximum figure based on a 1.6mm
track pitch.
USER DATA CAPACITY*
(1 MBytes = 1024 x 1024 )
656 MBytes, Mode 1
748 MBytes, Mode 2
RECORDING/PLAYING TIME*
74 minutes and 42 seconds
NUMBER OF BLOCKS/DISC*
336,150
USER DATA/BLOCK (Excluding sync, header, sub header, and ECC bytes)
2048 Bytes, Mode 1 and Mode 2 Form 1
2336 Bytes, Mode 2
2328 Bytes, Mode 2 Form 2
ADDRESS DESCRIPTION
Min, Sec, Block
RECORDING SURFACES
1
DISC DIAMETER
120 mm or 80 mm
DISC CENTER HOLE
15 mm diameter
THICKNESS
1.2 mm
TRACK PITCH
1.6 microns (15,875 TPI), typical
Sony Optiarc Inc. Confidential
Sony Optiarc Super Multi Drive Specification AD-7717H-01 Specification Rev. 0.90
6/25
SCANNING VELOCITY
1.2 ~ 1.4 m/sec (Normal Speed)
ROTATION SPEED
497 to 214 rpm (Normal Speed), Varies over radius
LATENCY (AVERAGE)
60 to 140 msec (Normal Speed), Varies over radius
BLOCKS/ROTATION
9.1 to 21.1 Blocks/rotation, Variable
4.2 PERFORMANCE REQUIREMENTS
Unless otherwise indicated, the following performance specifications will be met over the temperature, humidity,
and voltage range called out in section 5.0 and 10.0 of this document and will be verified using a test disc.
4.2.1 DVD MODES AND BLOCK LENGTH SUPPORTED
4.2.1.1 DVD READABLE FORMAT, MODES AND BLOCK LENGTH SUPPORTED
a) Format and Modes Supported
DVD-Video (8cm/12cm, Single and Dual Layer), DVD-ROM (8cm/12cm, Single and Dual Layer),
Multi-Border, Multi-Session
b) Block Length Supported
2048 Bytes/sector
4.2.1.2 DVD WRITABLE FORMAT, MODES AND BLOCK LENGTH SUPPORTED
a) Format and Modes Supported
DVD-Video, DVD-ROM, Multi-Session (DVD+R/+RW), Multi-Border (DVD-R/-RW)
b) Block Length Supported
2048 Bytes/sector
4.2.2 DVD WRITE METHOD SUPPORTED
a) Uninterrupted Write
Disc at once
b) Interrupted Write
Random write (DVD+R/+RW, DVD-RAM Ver.2)
Sequential write (DVD+R/+RW, DVD-RAM Ver.2)
Incremental (DVD-R/-RW)
Multi-Border (DVD-R/-RW)
Layer Jump Recording (DVD-R DL)
Restricted overwrite (DVD-RW)
4.2.3 DVD WRITABLE MEDIA
Refer to “Supported Media List” for details of media and recording speed.
a) DVD+R Media (16x/8x/4x/2.4x)
Taiyo-Yuden, Mitsubishi (Verbatim), TDK
b) DVD+R Double Layer Media (8x/2.4x)
Mitsubishi (Verbatim)
c) DVD+RW Media (8x/4x/2.4x)
Mitsubishi (Verbatim), TDK
d) DVD-R Media (16x/8x/4x/2x)
Mitsubishi (Verbatim), TDK, Taiyo-Yuden, PVC, Fuji Film, Ritek
e) DVD-R DL Media (4x)
Mitsubishi (Verbatim)
f) DVD-RW Media (6x/4x/2x/1x)
JVC, PVC, Mitsubishi (Verbatim), TDK
g) DVD-RAM (Ver.2) Media (5x/3x/2x)
Panasonic,Hitachimaxell
h) DVD+RW/-RW Rewrite
1,000 times
i) DVD-RAM Rewrite
10,000 times
Sony Optiarc Inc. Confidential
Sony Optiarc Super Multi Drive Specification AD-7717H-01 Specification Rev. 0.90
7/25
4.2.4 CD MODES AND BLOCK LENGTH SUPPORTED
4.2.4.1 CD READABLE FORMAT, MODES AND BLOCK LENGTH SUPPORTED
a) Format and Modes Supported
CD-Audio (8cm/12cm), CD-ROM (Mode 1 and mode 2), CD-ROM XA (Mode 2, form 1 and form 2),
Photo CD (Single or multiple sessions), CD-I (FMV), Video CD, CD Extra., CD-TEXT
b) Block Length Supported
CD-Audio
2352 and 2368 Bytes
CD-ROM (Mode 1)
2048 and 2352 Bytes
CD-ROM XA/CD-I
Form 1 2048, 2328, 2336, 2340 and 2352 Bytes
Form 2 2328, 2336, 2340 and 2352 Bytes
4.2.4.2 CD WRITABLE FORMAT, MODES AND BLOCK LENGTH SUPPORTED
a) Format and Modes Supported
CD-Audio (8cm/12cm), CD-ROM (Mode 1 and mode 2), CD-ROM XA (Mode 2, form 1 and form 2),
Photo CD (Single or multiple sessions), CD-I (FMV), Video CD, CD Extra, CD-TEXT
b) Block Length Supported
CD-Audio
2352 Bytes
CD-ROM (Mode 1)
2048 Bytes
CD-ROM XA/CD-I
Form 1 2048 and 2332 Bytes
Form 2 2332 Bytes
4.2.5 CD WRITE METHOD SUPPORTED
a) Uninterrupted Write
Disc at once
b) Interrupted Write
Track at once
Session at Once
Packet Writing (Fixed size Packets, Variable size Packets)
4.2.6 CD WRITABLE MEDIA
Refer to “Supported Media List” for details of media and recording speed
a) CD-R Media (48x/40x/32x/24x/16x/8x)
Mitsubishi (Verbatim), Taiyo-Yuden, Sony, CMC, JVC, TDK
b) CD-RW Media (US+/US/HS/MS)
Mitsubishi (Verbatim), RITEK,
c) CD-RW Rewrite
4.2.7 TRANSFER RATE
4.2.7.1 READ SPEED AND TRANSFER RATE
USER BYTES/SEC. (SUSTAINED) (1 kBytes = 1024 bytes)
a) DVD-ROM
Single / Dual Layer
3.3-8x CAV
4.5-11 MBytes/sec
3.3-8x CAV
4.5-11 MBytes/sec
3.3-8x CAV
4.5-11 MBytes/sec
3-5x ZCLV
4.1-6.9 MBytes/sec
b) DVD+R/-R/+RW/-RW
c) DVD+R DL/-R DL
d) DVD-RAM
e) DVD-Video with CSS protection
1.6-4x CAV
f) CD-ROM/CD-R/RW
Mode 1 and Mode 2 Form 1 (2048 Bytes)
10-24x CAV
g) CD-DAE
Ripping
10-24x CAV
2.2-5.5 MBytes/sec
1500 - 3600 kBytes/sec
1500 - 3600 kBytes/sec
Sony Optiarc Inc. Confidential
Sony Optiarc Super Multi Drive Specification AD-7717H-01 Specification Rev. 0.90
8/25
h) Mode 2 and Mode 2 Form2
7-16x CAV
1050 - 2400 kBytes/sec
4.2.7.2 WRITE SPEED AND TRANSFER RATE
a) DVD+R
8x CAV
8x ZCLV
6x ZCLV
4x ZCLV
2.4x CLV
b) DVD+R DL
6x ZCLV
4x ZCLV
2.4x CLV
c) DVD+RW
8x ZCLV
6x ZCLV
4x ZCLV
2.4x CLV
d) DVD-R
8x CAV
8x ZCLV
6x ZCLV
4x ZCLV
2x CLV
e) DVD-R DL
6x ZCLV
4x ZCLV
2x CLV
f) DVD-RW
6x ZCLV
4x ZCLV
2x CLV
1x CLV
g) DVD-RAM (Version 2)
5x ZCLV
3x CLV
2x CLV
h) CD-R
24x CAV
24x ZCLV
16x ZCLV
8x CLV
i) CD-RW (US+/US/HS/MS)
24x ZCLV (US+/US-RW)
10x ZCLV (HS-RW)
4x CLV (MS-RW)
4.5 - 11 MBytes/sec
3.3 - 11 MBytes/sec
3.3 - 8.2 MBytes/sec
3.3 - 5.5 MBytes/sec
3.3 MBytes/sec
3.3 - 8.3 MBytes/sec
3.3 - 5.5 MBytes/sec
3.3 MBytes/sec
4.5 - 11 MBytes/sec
4.5 - 8.2 MBytes/sec
3.3 - 5.5 MBytes/sec
3.3 MBytes/sec
4.5 - 11 MBytes/sec
2.7 - 11 MBytes/sec
2.7 - 8.3 MBytes/sec
2.7 - 5.5 MBytes/sec
2.7 MBytes/sec
3.3 - 8.3 MBytes/sec
2 .7- 5.5 MBytes/sec
2.7 MBytes/sec
2.7 - 8.2 MBytes/sec
2.7 - 5.5 MBytes/sec
2.7 MBytes/sec
1.38 MBytes/sec
4.1-6.9 MBytes/sec
4.1 MBytes/sec
2.7 MBytes/sec
1500 - 3600 kBytes/sec
1200 - 3600 kBytes/sec
1200 - 2400 kBytes/sec
1200 kBytes/sec
1200 – 3600 kByte/sec
1200 - 1500 kBytes/sec
600 kBytes/sec
Sony Optiarc Inc. Confidential
Sony Optiarc Super Multi Drive Specification AD-7717H-01 Specification Rev. 0.90
9/25
4.2.8 SERIAL ATA INTERFACE BURST RATE
Generation 1
PIO
DMA
support
support
4.2.9 ROTATION SPEED
4.2.9.1 DVD MEDIUM
3.3-8x CAV
2.5-6x CAV
1.6-4x CAV
6x ZCLV
4x ZCLV
2.4x CLV
2x CLV
4600 rpm, Constant
3480 rpm, Constant
2300 rpm, Constant
1984 ~ 4600 rpm
1984 ~ 3333 rpm
1379 ~ 3333 rpm
1149 ~ 2777 rpm
4.2.9.2 DVD-RAM (VERSION 1)
1x CLV (Read only)
1015 ~ 2254 rpm
4.2.9.3 DVD-RAM (VERSION 2)
3-5x ZCLV
3x CLV
2x CLV
3439 ~ 4869 rpm
2063 ~ 4869 rpm
1375 ~ 3246 rpm
4.2.9.4 CD MEDIUM
10-24x CAV
8-20x CAV
7-16x CAV
4-10x CAV
20x ZCLV
16x ZCLV
10x ZCLV
8x CLV
4x CLV
5100 rpm, Constant
4200 rpm, Constant
3500 rpm, Constant
2100 rpm, Constant
3150 ~ 5000 rpm
3150 ~ 5000 rpm
2140 ~ 4970 rpm
1712 ~ 3976 rpm
856 ~ 1988 rpm
4.2.10 ACCESS TIME (INCLUDING LATENCY)
Access time is the time from the raising edge of /DA0 of the last command byte to the falling edge of /IOCS16 of
after the first data byte returned to host (Assumes no disconnect) at horizontal operation. This measurement is
done after 200 times of random seeks after a disc insertion. Access time specifications will be met at horizontal
operation and in the following environmental conditions.
Temperature
Relative humidity
+10°C ~ +30°C
< 85% (No condensation)
4.2.10.1 DVD MEDIUM
a) Full Stroke
Average 200 seeks from LBA 0 to 2,293,759 and from block 2,293,759 to block 0
A total of 400 seeks. (Seek command instead of read command is used.)
DVD-5 3.3-8x CAV
340 msec typ
410 msec max
DVD-9 2.5-6x CAV
370 msec typ
450 msec max
b) Random Stroke
Average over 500 random access. (Seek command instead of read command is used.)
DVD-5 3.3-8x CAV
180 msec typ
220 msec max
DVD-9 2.5-6x CAV
200 msec typ
240 msec max
Sony Optiarc Inc. Confidential
Sony Optiarc Super Multi Drive Specification AD-7717H-01 Specification Rev. 0.90
10/25
4.2.10.2 CD MEDIUM
a) Full Stroke
Average 200 seeks from block 0 to block 269,999 and from block 269,999 to block 0
A total of 400 seeks. (Seek command instead of read command is used.)
10-24x CAV
310 msec typ
370 msec max
b) Random Stroke
Average over 500 random access. (Seek command instead of read command is used.)
10-24x CAV
150 msec typ
180 msec max
4.2.10.3 DVD-RAM MEDIUM
a) Full Stroke
Average 200 seeks from LBA 0 to 2,293,759 and from block 2,293,759 to block 0
A total of 400 seeks. (Seek command instead of read command is used.)
3-5x ZCLV
450 msec typ
b) 1/3 Stroke
Average over 100 seeks from LBA 532,480 to 1,265,664. (Seek command instead of read command is
used.)
3-5x ZCLV
300 msec typ
c) Random Stroke
Average over 500 random access. (Seek command instead of read command is used.)
3-5x ZCLV
300 msec typ
4.2.11 SPIN UP AND TRAY EJECT TIME
a) Spin Up Time
CD-ROM
(Power on to drive ready)
DVD-ROM
b) Spin Down Time
C) Tray Eject Time (Include spin down time)
11 sec typ
11 sec typ
6 sec typ
7 sec typ
4.2.12 USER ERROR RATES
a) Hard Error Rate: DVD and CD Mode 1 (With up to 5 retries and layered ECC on)
< 10-12 Block/bit
b) Soft Error Rate: CD Mode 2 (With up to 5 retries)
< 10-9 Block/bit
c) Seek Error Rate
< 10-6 Block/bit
4.2.13 MPC3 COMPLIANCE
This drive complies with the Microsoft specification for MPC3. The CPU utilization is less than 40% at data rate
of 600 KB/sec, less than 20% at data rate of 300 KB/sec, and no less than 16 KB of block size.
4.2.14 FLASH ROM UPDATE
The firmware is updated via Serial ATA interface with the Optiarc Flash ROM Utility.
4.2.15 DVD CONTENT SCRAMBLE SYSTEM AUTHENTICATION
This drive fully complies with the ATAPI DVD Key Exchange and Authentication specification, which is a
digital cryptograph.
4.2.16 REGION PLAYBACK CONTROL
This drive supports RPC phase II provided by SFF80.91v5 Rev. 1.4.
The user can change the region code, which is stored in the drive up to 5 times by sending the appropriate
command. Usually, the command is issued by MPEG Player application.
Sony Optiarc Inc. Confidential
Sony Optiarc Super Multi Drive Specification AD-7717H-01 Specification Rev. 0.90
11/25
4.2.17 MAXIMUM PLAYBACK SPEED
The maximum playback speed with various discs is limited as follows.
DVD-ROM (Dual Layer):
DVD-Video with CSS protection:
DVD-RAM (Data tracks)
DVD+/-R DL (Data tracks)
CD-DAE Playback:
CDROM (Mode 2 form2):
CD-RW (Mode 1):
3.3 - 8x
1.6 - 4x
3 - 5x
3.3 - 8x
8 - 24x
7 - 16x
10 - 24x
In addition, the drive will limit the maximum playback speed automatically by the quality of the disc.
The drive may playback with lower speed than the speed mentioned above.
4.2.18 TOLERANCE PERTAINING TO MEDIA
The drive can read the following Media
CD:
DVD:
Black dot
Less than 0.6 mm
Less than 0.6 mm
Finger Print
Less than 65 um
Less than 65 um
Sony Optiarc Inc. Confidential
Sony Optiarc Super Multi Drive Specification AD-7717H-01 Specification Rev. 0.90
12/25
5.0 ENVIRONMENTAL
This section establishes the environmental and physical conditions which apply to the product. This drive meets the
following environmental requirements under normal operating conditions.
5.1 TEMPERATURE (NON-CONDENSING)
5.1.1 NON-OPERATING
–40°C to +65°C
5.1.2 OPERATING
5°C to +50°C (Writing) / 5°C to +55°C (Reading)
Note) Temperature is measured on the top cover.
5.2 HUMIDITY
5.2.1 NON-OPERATING
5% to 95% (No condensation, Maximum wet bulb temp 38°C)
5.2.2 OPERATING
20% to 80% (No condensation, Maximum wet bulb temp 29°C)
5.3 VIBRATION
5.3.1 NON-OPERATING
The drive unit meets specification described below with continuous random vibration.
Acceleration
Frequency
Direction of vibration
3.94 Grms
5 to 800 Hz
X, Y and Z axis
5.3.2 OPERATING
The drive unit meets specification described below with random sine wave vibration.
Acceleration
Frequency
Direction of vibration
CD:
Read 0.45Grms, Write 0.2 Grms
DVD:
Read 0.45Grms, Write 0.2 Grms
5 to 300 Hz Flat, 300 to 500 Hz -6dB
X, Y and Z axis
5.4 SHOCK
5.4.1 NON-OPERATING
The drive unit can withstand following shock.
Discs are not in the drive at all and the drive is powered off.
Pulse Duration and Peak level
Direction of Shock
300G / 2ms
150G / 10ms
±X, ±Y, and ±Z axis (2 directions per axis, so total 6 shocks)
Sony Optiarc Inc. Confidential
Sony Optiarc Super Multi Drive Specification AD-7717H-01 Specification Rev. 0.90
13/25
5.4.2 OPERATING
The drive unit can withstand shock with a 1/2 sine wave shape.
Data read with retry (Not specified about audio play)
Pulse Duration and Peak level
Pulse Duration
Direction of shock
CD
Read 6G, Write 1G
DVD
Read 6G, Write 1G
11msec
±X, ±Y, and ±Z axis
5.5 VIBRATION AND DROP (PACKAGED)
5.5.1 VIBRATION (PACKAGED)
Test time
Test Axis
Vibration
Packaged
30 min/side
6 surface
Random mode
Bulk Carton (40 sets)
Spectrum Break Points
Frequency
G2/Hz
1Hz
0.0001
4Hz
0.01
100Hz
0.01
200Hz
0.001
Total random vibration spectrum energy shall be 1.146 Grms.
5.5.2 DROP (PACKAGED)
Height
Packaged
92cm (6 surfaces / 1 corners / 3 edges)
Bulk Carton (40 sets)
Sony Optiarc Inc. Confidential
Sony Optiarc Super Multi Drive Specification AD-7717H-01 Specification Rev. 0.90
14/25
6.0 QUALITY AND RELIABILITY
6.1 COSMETIC
No scratches, cracks, stains and damages are visible on the front panel in case that you take a look at them at the
distance of 400 mm from away it. No scratches, cracks, stains and damages are visible on the top, bottom, side and
rear panel in case that a look at them at the distance of 600 mm from away it.
6.2 DISC LOADER MECHANISM LIFE
This drive unit has a drawer loading mechanism.
The drive is capable of at least 20,000 disc loading/unloading operations at 25°C temperature without degradation or
failure. Both motions of extending and retracting the tray from the drive are smooth and quiet.
6.3 MTBF
The MTBF is 80,000 power on hours (POH) when operated at 25°C temperature, nominal voltage, and other
environmental limits, based on the following assumptions:
- The operating duty cycle is 10% of power on time. During this time, the drive is either reading or seeking (Random
multiple blocks read).
- The drive is in dormant mode (i.e. the laser diode is off and spindle motor not spinning, the drive is power on) for
90% of power on time.
6.4 OPTICAL PICKUP ACTUATOR MECHANISM
The drive is capable at least 4,000,000 random seeks at +40°C
6.5 MTTR (MEAN TIME TO REPAIR)
30 minutes
6.6 ELECTROSTATIC DISCHARGE SUSCEPTIBILITY (ESD)
The drive is installed in Optiarc specified shielded case which meets the ESD specified in the IEC 61000-4-2
(EN61000-4-2).
Contact discharge
+/-6kV (No performance degradation or failure)
+/-8kV (Temporary performance degradation or failure, No destroy)
Air discharge
+/-12kV (No performance degradation or failure)
+/-15kV (Temporary performance degradation or failure, No destroy)
Energy storage capacitance
Discharge resistance
150pF +/-10%
330 ohms +/-10%
6.7 PRODUCTION FINAL TEST
Due to the integrated nature of this product, the Optiarc performs a final system test.
Sony Optiarc Inc. Confidential
Sony Optiarc Super Multi Drive Specification AD-7717H-01 Specification Rev. 0.90
15/25
7.0 REGULATIONS AND STANDARDS
7.1 SAFETY APPROVAL
UL (UL60950-1), C-UL (CSA C22.2 No.60950-1-03), TÜV (EN60950-1, EN60825-1), CB (IEC 60950-1,
IEC60825-1)
7.2 EMC AND COMPLIANCE
CE Marking (EN55022 Class B, EN55024), C-tick (AS/NZ CISPR22 Class B), BSMI, KCC
7.3 FDA COMPLIANCE
The product satisfies all the requirements specified in the Code of Federal Regulation 21CFR part 1040.10 and
1040.11.
7.4 RoHS COMPLIANCE
The product complies with EU Directive 2002/95/EC RoHS.
7.5 WHQL
The product complies with WHQL for Windows Vista. Both for 32 bits and 64 bits.
8.0 ACOUSTIC NOISE
8.1 GENERAL
Noise measurement must conform to the testing procedure for measuring Acoustic Noise on office equipment as
specified by the:
ISO Standard
ISO9296 Using measurements defined in ISO
ECMA74
8.2 TEST CONDITION
The test condition is free field condition over are flexing plane. This condition can be simulated in unechoic
chamber. Sound pressure shall measure as defined in standard ECMA-74(Seated Operator Position), while the
drive (in Note-PC) is actively seeking and rotating at its maximum speed, with 0.3g/cm unbalanced test media.
Both random access and sequential access should be tesetd.
Sony Optiarc Inc. Confidential
Sony Optiarc Super Multi Drive Specification AD-7717H-01 Specification Rev. 0.90
16/25
8.3 NOISE SPECIFICATION
A- Weighted RMS
Drive On (Seeking)
Drive On (Non-Seeking)
: 47.5 dB(A)
: 47.5 dB(A)
Sound-level meter
30 degrees
0.45m
0.25m
Note PC
The number of measurement: Two sets.
Sony Optiarc Inc. Confidential
Sony Optiarc Super Multi Drive Specification AD-7717H-01 Specification Rev. 0.90
17/25
9.0 MECHANICAL
9.1 DIMENSIONS AND MOUNTING ORIENTATION
9.1.1 DIMENSIONS
Attached Figure 1 shows the dimensions for this drive.
9.1.2 MOUNTING ORIENTATION
This drive unit shall be installed and operated in the horizontal and vertical orientation.
The drive operates in the horizontal and vertical orientation within the angular tolerance range described below.
Horizontal
: front side up or down
: left side up or down
: front side up or down
: top side up or down
Vertical
±15°
±15°
±15°
±15°
9.1.3 WEIGHT
160g max
without Bezel
Sony Optiarc Inc. Confidential
Sony Optiarc Super Multi Drive Specification AD-7717H-01 Specification Rev. 0.90
18/25
9.1.4 FORCE RECOMMENDED VALUE RANGE ON TOP COVER
9.2 MATERIAL & COLOR
9.2.1 EJECT BUTTON, FRONT BEZEL
Eject button and front bezel shall be molded as follows :
Material: PC/ABS
Flame Retardant Grade: UL94V-1
Color: Black (OEM Available)
Finish: Mat
9.2.2 TRAY
Tray shall be molded as follows:
Material
Flame Retardant Grade
Color
Finish
PC/ABS
UL94V-2
Black
Matt
9.2.3 ACTIVITY LED
Busy
Green
9.3 INTERFACE CONNECTOR
The drive has a standard 13-pin shrouded, keyed, male connector for Serial ATA signal. For pin out description of
Serial ATA interface, refer to 10.2.2.1 Serial ATA interface connectors.
P6 P5 P4 P3 P2 P1
Part of Power (6 pins)
S7 S6 S5 S4 S3 S2 S1
Part of serial ATA signal connector (7 pins)
9.4 DISC LOADING MECHANISM
Sony Optiarc Inc. Confidential
Sony Optiarc Super Multi Drive Specification AD-7717H-01 Specification Rev. 0.90
19/25
This drive uses a drawer type loading mechanism for loading and removing the disc from the drive.
9.4.1 EJECT BUTTON
The front bezel of the drive unit has a eject button to eject the tray. This eject button is enabled upon power up.
9.4.2 EMERGENCY EJECT
An emergency eject mechanism is equipped to unload the disc in emergency situation. The emergency hole is
located on the front bezel.
9.4.3 EJECT COMMAND
The host can also eject the tray from the drive through an ATAPI CD-ROM command.
9.5 LABELING ON A DRIVE
The drive has the label indicated following contents and identifications visible from the outside of the unit:
(1) Production date, country of origin, serial number, model number.
(2) Safety and agency approvals
(3) Laser warning (NCDRH)
(4) Commodity Tracking (CT)
Sony Optiarc Inc. Confidential
Sony Optiarc Super Multi Drive Specification AD-7717H-01 Specification Rev. 0.90
20/25
10.0 ELECTRICAL
10.1 POWER
10.1.1 VOLTAGE
10.1.1.1 VOLTAGE TOLERANCE
+5V (DC)
+/– 5%
10.1.1.2 RIPPLE AND NOISE TOLERANCE
+5V (DC)
1 kHz to 10MHz
100 mV (peak to peak)
10.1.2 CURRENT
Spinup
1000 mA / 1300 mA
Continuous Random access (CD 10-24x CAV) 1000 mA / 1000 mA
Continuous Random access (DVD-RAM )
1250 mA / 1500 mA
Continuous Read (CD 10-24x CAV)
800 mA / 850 mA
Continuous Read (DVD 8x CAV)
800 mA / 800 mA
Continuous Read (DVD-RAM)
800 mA / 850 mA
Continuous Write (CD 24x CAV)
1000 mA / 1100 mA
Continuous Write (DVD 8x CAV)
950 mA / 1000 mA
Tray Eject
600 mA / 700 mA
Idle (CD 4-10x CAV Pause)
650 mA / 650 mA
Idle (DVD-RAM)
750 mA / 750 mA
Standby
(Slumber)
50 mA / - mA
Standby
(Partial )
100 mA / - mA
Note:
“Average” current is the arithmetic mean value of the current measured during a typical 4 second period.
“Maximum” current is the arithmetic mean value of the current measured during a typical 0.5
second period.
Sony Optiarc Inc. Confidential
Sony Optiarc Super Multi Drive Specification AD-7717H-01 Specification Rev. 0.90
21/25
10.2. SERIAL ATA INTERFACE
10.2.1 GENERAL
This drive unit uses Serial ATA interface, which conforms to the Mt. Fuji Commands for CD and DVD Devices:
SFF80.91v5 rev. 1.40 to communicate with the host computer. IDE interface (ISO X3T9.2 791D) addresses the
electrical interface. The ATAPI CD-ROM specification: SFF-8020 Rev.2.6 addresses command protocol.
Specific command definition supported by this drive is provided by Optiarc AD-7717H ATAPI/ IDE (SATA)
Interface Delta Specification Rev. 1.00 and this specification..
10.2.2 ELECTRICAL
The Serial ATA bus uses differential drivers and receivers.,
10.2.2.1 CONNECTOR PIN DIFINITION
7-pin Signal Segment
Signal
S1
S2
S3
S4
S5
S6
S7
n
1
2
3
4
5
6
7
Description
GND
2nd mate
A+
Differential signal pair A from Phy
AGND
2nd mate
BDifferential signal pair B from Phy
B+
GND
2nd mate
n
1
2
3
4
5
6
Description
DP
Device present (1K Ohm Pull-down inside drive)
+5V
+5V
MD
Manufacturing Diagnostic (Eject Notification Circuit)
GND
GND
6-pin Power Segment
Signal
P1
P2
P3
P4
P5
P6
Sony Optiarc Inc. Confidential
Sony Optiarc Super Multi Drive Specification AD-7717H-01 Specification Rev. 0.90
22/25
10.2.2.2 SIGNAL CHARACTERITICS
Vcm dc
Nom
250
Min
200
Max
450
units
mV
Comments
Common mode DC level measured at
Receiver connector.
10.2.3 COMMANDS
10.2.3.1 GENERAL
This drive unit implements The ATAPI DVD-R/-RW/+R/+RW and CD-R/-RW commands and features. The
following is a brief description of the ATAPI DVD-R/-RW/+R/+RW and CD-R/RW features to be
implemented.
Command description is provided by the following specifications:
ATA Packet Interface for CD-ROMs: SFF-8020i Revision 2.6
SCSI-3 Multimedia Commands: X3T10/1048D Revision10A
SCSI Multimedia Commands -2: T10/1228-D Revision10a
SCSI Multimedia Commands -3(MMC-3): T10/1363-D Revision 10g
Optiarc AD-7717H ATAPI/IDE (SATA) Command Set Specification
MMC4 T10/1545-D Rev.3d
10.2.3.2 TASK FILE COMMANDS
Command
Execute drive diagnostic
NOP
ATAPI Packet Command
ATAPI Identify Device
ATAPI Soft Reset
Check Power Mode
Idle Immediate
Idle
Set Features
Standby immediate
Standby
Sleep
Op-code
90h
00h
A0h
A1h
08h
E5h
E1h
E3h
EFh
E0h
E2h
E6h
Remark
10.2.3.3 PACKET COMMANDS
Command
Op-code
Remark
BLANK
A1h
CLOSE TRACK/SESSION
5Bh
FORMAT UNIT
04h
GET CONFIGURATION
46h
GET PERFORMANCE
ACh
GET EVENT/STATUS NOTIFICATION
4Ah
INQUIRY
12h
MECHANISM STATUS
BDh
MODE SELECT(10)
55h
MODE SENSE(10)
5Ah
PREVENT/ALLOW MEDIUM REMOVAL
1Eh
READ(10)
28h
READ(12)
A8h
READ BUFFER CAPACITY
5Ch
READ CAPACITY
25h
READ CD
BEh
READ CD MSF
B9h
READ DISC INFORMATION
51h
READ DVD STRUCTURE
ADh
READ FORMAT CAPACITIES
23h
Feature 0023h & 0028h
READ HEADER
44h
Sony Optiarc Inc. Confidential
Sony Optiarc Super Multi Drive Specification AD-7717H-01 Specification Rev. 0.90
23/25
READ SUB-CHANNEL
READ TOC/PMA/ATIP
READ TRACK INFORMATION
REPAIR TRACK
REPORT KEY
REQUEST SENSE
RESERVE TRACK
REZERO UNIT
SCAN
SEND DVD STRUCTURE
SEEK
SEND CUE SHEET
SEND EVENT
SEND KEY
SEND OPC INFORMATION
SET CD-ROM SPEED
SET STREAMING
START STOP UNIT
STOP PLAY/SCAN
SYNCHRONIZE CACHE
TEST UNIT READY
VERIFY(10)
WRITE(10)
WRITE(12)
WRITE AND VERIFY(10)
42h
43h
52h
58h
A4h
03h
53h
01h
Bah
BFh
2Bh
5Dh
A2h
A3h
54h
BBh
B6h
1Bh
4Eh
35h
00h
2Fh
2Ah
AAh
2Eh
10.3 DATA BUFFER
The drive electronics includes 2 MBytes read ahead data buffer in the Serial ATA controller.
10.4 AUDIO SIGNAL INTERFACE
This drive unit has no analog audio circuit. Then CD-audio disc can be played by DAE function
11.0 PACKAGING
The drives (40 sets) will be packed in a bulk carton using a cardboard insert to protect against shock and vibration.
Sony Optiarc Inc. Confidential
Sony Optiarc Super Multi Drive Specification AD-7717H-01 Specification Rev. 0.90
24/25
*Revision
0.90
Jul 7, 2010
First Releases
Sony Optiarc Inc. Confidential
Sony Optiarc Super Multi Drive Specification AD-7717H-01 Specification Rev. 0.90
25/25