REF : 20090825-B PROD. SPECIFICATION FOR APPROVAL ABC'S DWG No. SHIELDED SMD POWER INDUCTOR NAME PAGE: 1 HP0602□□□□2□-□□□ ABC'S ITEM No. Marking D B C R10 Ⅰ﹒MECHANICAL DIMENSIONS： A : 7.20 ± 0.3 m/m B : 6.50 ± 0.2 m/m C : 3.00 ± 0.3 m/m D : 2.40 max. E : 1.70 ± 0.5 m/m m/m F : 3.40 typ. m/m G : 3.70 typ. m/m H : 7.40 typ. m/m E Inductance code F A G H ( PCB Pattern ) a Ⅱ﹒SCHEMATIC DIAGRAM： b 1 2 c Ⅲ﹒MATERIALS LIST： a﹒Core：Iron powder Peak Temp：250℃ max. Max. Peak Temp - 5℃：30sec max. Max time above 217℃ ：60sec~150sec max. b﹒Wire：Enamelled copper wire Temperature Rising Area c﹒Cilp：Cu / Ni /Sn Preheat Area +4.0℃ / sec max. d﹒Remark：Products comply with RoHS' requirements 150 ~ 200℃ / 60 ~ 120sec Reflow Area Forced Cooling Area +3.0℃ / sec max. -(1.0 ~ 5.0)℃ / sec max. Peak Temperature: 250℃ 250 Ⅳ﹒GENERAL SPECIFICATION： a﹒Storage temp.：-55℃ ~ +125℃ b﹒Operating temp .：-55℃ ~ +125℃ ( Temp. rise included ) c﹒Resistance to solder heat：250℃. 10 secs. AR-001A Temperature ( ℃ ) 217℃ 60sec~150sec 200 60sec max. 150 60sec~120sec 100 50 0 50 100 150 Time ( seconds ) 200 250 SPECIFICATION FOR APPROVAL PAGE: 2 REF : 20090825-B PROD. NAME SHIELDED SMD POWER INDUCTOR ABC'S DWG No. HP0602□□□□2□-□□□ ABC'S ITEM No. Ⅴ﹒ELECTRICAL CHARACTERISTICS： Inductance L ( μH ) Isat(A) typ. HP0602R10M2□-□□□ 0.10 ± 20 ％ 50.0 HP0602R22M2□-□□□ 0.22 ± 20 ％ HP0602R33M2□-□□□ DWG No. RDC ( mΩ ) Irms(A) typ. max. typ. 30.0 2.0 1.5 34.0 21.0 3.5 3.0 0.33 ± 20 ％ 22.0 18.0 4.5 4.0 HP0602R47M2□-□□□ 0.47 ± 20 ％ 21.0 13.0 6.5 6.0 HP0602R68M2□-□□□ 0.68 ± 20 ％ 18.0 11.0 9.5 9.0 HP0602R82M2□-□□□ 0.82 ± 20 ％ 17.0 10.0 12.0 11.0 HP06021R0M2□-□□□ 1.00 ± 20 ％ 16.0 9.0 14.5 13.5 HP06021R5M2□-□□□ 1.50 ± 20 ％ 15.0 7.0 21.5 18.5 HP06022R2M2□-□□□ 2.20 ± 20 ％ 14.0 6.0 34.0 28.0 HP06023R3M2□-□□□ 3.30 ± 20 ％ 13.0 5.0 52.0 36.5 HP06024R7M2□-□□□ 4.70 ± 20 ％ 10.0 4.0 63.0 45.5 HP06026R8M2□-□□□ 6.80 ± 20 ％ 9.0 3.5 95.0 72.5 HP06028R2M2□-□□□ 8.20 ± 20 ％ 8.0 3.0 106.0 84.5 HP0602100M2□-□□□ 10.0 ± 20 ％ 7.0 2.5 129.0 116.0 1). □：Packaging information … A：Bulk B：Taping Reel 2). "- □□□":Reference code 3). Measured frequency of inductance is 100 KHz / 0.25V 4). Isat base on inductance drop 20% typ. of L value at 20℃ 5). Irms base on temp. rise 40℃ typ. AR-001A SPECIFICATION FOR APPROVAL PAGE: 3 REF : 20090825-B PROD. ABC'S DWG No. SHIELDED SMD POWER INDUCTOR NAME HP0602□□□□2□-□□□ ABC'S ITEM No. Ⅵ﹒PACKAGING INFORMATION： ( 1 ) Configuration T Cover Tape N B A 2.0±0.5 ∮C ∮C D G Embossed carrier ※Carrier tape width : D P:12 m/m 4 m/m End Start R10 Leader no component 200 m/m min. R10 R10 R10 Trailer no component 400 m/m min. Components User direction of feed ( 2 ) Dimensions Unit:m/m Style A B C D 13 - 16 330 21±0.8 13±0.5 16 G 18 +0 N 50 T -0 22.4 ( 3 ) Q'TY & G.W. Per package Inner : Reel Outer : Carton Series HP0602 AR-001A Q'TY (pcs) G.W. (gw) Style Q'TY (pcs) G.W. (Kg) Size (cm) 1,900 1,500 13 - 16 11,400 10.0 38 x 37 x 22 SPECIFICATION FOR APPROVAL REF : 20090825-B PROD. NAME PAGE: 4 SHIELDED SMD POWER INDUCTOR ABC'S DWG No. HP0602□□□□2□-□□□ ABC'S ITEM No. Ⅶ﹒DWGING NUMBER EXPRESSION： H P 0 6 0 2 Reference code Appendix code 2 : Package Appendix code 1 : Classification Tolerance code Electrical code Dimension code Type code Appendix code 1：Product Classification L：Lead Free Standard products comply with RoHS' requirements 1 ~ 9：Lead Free Special products comply with RoHS' requirements Appendix code 2：Package Information Code AR-001A Inner package Inner package Q'TY A T.B.D. T.B.D B T / R ( Reel package ) 1900 pcs Remark SPECIFICATION FOR APPROVAL REF : 20090825-B PROD. NAME PAGE: 5 SHIELDED SMD POWER INDUCTOR ABC'S DWG No. HP0602□□□□2□-□□□ ABC'S ITEM No. Ⅷ﹒RELIABILITY TEST： Test item Solderability Thermal shock test ( Temp. cycle ) Specification Test condition More than 95% of the terminal electrode Shall be covered With fresh solder. Preconditioning: 150℃/16Hrs±30min Dry Bake Solder : Sn96.5 / Ag3 / Cu0.5 or equivalent Solder temp. :245±5℃ Flux : Rosin Dip time: 5±0.5sec Electrical oharacteristics shall not change more than ±20% Room temp. 15 minutes -55 ℃ 30 minutes Room temp. 15 minutes +125 ℃ Total : 50 cycles Humidity Test Temperature : 40±2℃ Humidity : 90±5% Time : 1000 hours High temp. Resistance test Temperature : 125±5℃ Applied current : Per spec. Time : 96 hours AR-001A 30 minutes SPECIFICATION FOR APPROVAL REF : 20090825-B PROD. NAME PAGE: 6 ABC'S DWG No. SHIELDED SMD POWER INDUCTOR HP0602□□□□2□-□□□ ABC'S ITEM No. Ⅸ﹒UL CARD： OBMW2 Magnet Wire-Component September 8, 2000 E174837 JUNG SHING WIRE CO LTD 231 CHUNG CHENG RD, SEC 3 JEN-TEH HSIANG, TAINAN HSIEN TAIWAN Mtl Dsg AIW CFUEWB EIAIW EILOCKY EILOCKW EIW EIW-2 FL.EILOCKY LSFFW LSUEW PEW PEY SF.FLW SF.EIW SF.BY@ SF.FLY@ SF.BLOCKBS SF.EILOCKY# SF.EILOCKBS SF.BW@ SFFW Mark Dsg ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ BC Coat Typ Polyamideimide Polyurethane Polyesterimide Polyesterimide Polyesterimide Polyamideimide Polyamide Modified Epoxy ____ ____ Polyesterimide Polyesterimide Modified Polyester Polyurethane Polyurethane Polyester Polyester Modified Polyester Polyesterimide Modified Polyester Modified Polyester Modified Polyester Polyesterimide Polyesterimide Polyamide ____ ____ ____ ____Nylon ____ Nylon Nylon Modified Polyamide Polyamide Modified Polyamide ____ Modified Polyester Polyurethane 287806002 Mtl Dsg SFFY UEW-1 UEW-2 UEW-4 UEY UEY-2 OC ____ ____ ANSI Type Temp Class MW81-C MW75C MW35C ___ ___ 220 130 200 180 200 ___ MW74-C ___ MW79-C ___ ___ MW24-C MW26C MW77C MW27-C MW27-C ___ ___ ___ 180 180 MW26C MW79 ____ ____ ____ ____ ____ BC Coat Typ Polyurethane Polyurethane Polyurethane Polyurethane Polyurethane Polyurethane 155 155 A not-for-profit organization dedicated to public safety and committed to quality service Page 1 of 2 Mark Dsg ____ 220 200 155 155 130 155 155 155 180 155 155 155 OC Polyamide ____ ____ ____ Nylon Polyamide ANSI Type Temp Class MW80C MW2-C ___ 155 105 130 130 130 130 MW75C MW28-C MW28-C Marking: Company name or trademarks Recognized Component Mark. or 榮 星 電 線 @-May be suffixed by LZ; # - May be suffixed by LZ, EL or LZI. LZ - Signifies magned wires twisted together; EL - signifies base coated magnet wire laid parallel with top coat applied overall; LZL - signifies base coated magnet wire twisted together and covered with top coat overall. , material designation or marked designation on packaed or reel, and See General Information Preceding These Recognitions For use only in equipment where the acceptability of the combination is determined by Underwriters Laboratories Inc. 287806002 AR-001A Page 2 of 2 OBMW2⁄E174837 September 8 , 2000