SPECIFICATION FOR APPROVAL REF : 20090903-A PROD. NAME PAGE: 1 SH6038□□□□L□-□□□ ABC'S DWG NO. SHIELDED SMD POWER INDUCTOR ABC'S ITEM NO. Ⅰ﹒CONFIGURATION & DIMENSIONS： A B C D E G H I R : : : : : : : : : ±0.2 ±0.2 ±0.2 typ. typ. ref. ref. ref. ref. 6.80 6.80 3.80 2.30 2.20 2.10 7.30 2.60 2.70 m/m m/m m/m m/m m/m m/m m/m m/m m/m C 100 B A D G I E D R I H ( PCB Pattern suggestion ) Ⅱ﹒SCHEMATIC DIAGRAM： LCR Meter Ⅲ﹒MATERIALS： a a﹒Core：Ferrite DR core b﹒Core：Ferrite RI core c﹒Wire ：Enamelled copper wire ( Class F ) d﹒Adhesive ：Epoxy resin e﹒Terminal：Ag/Ni/Sn c b d Peak Temp：260℃ max. Max time above 230℃ ：50sec max. Max time above 200℃ ：70sec max. f﹒Remark：Products comply with RoHS' requirements e Temperature Rising Area Preheat Area +4.0 ℃ / sec max. 150 ~ 200℃ / 60 ~ 120sec Reflow Area Forced Cooling Area +2.0 ~ 4.0℃ -(1.0 ~ 5.0)℃ / sec max. / sec max. Peak Temperature: 260℃ 250 a﹒Temp. rise ：30℃ max. b﹒Storage temp.：-40℃ ----+125℃ c﹒Operating temp.：-40℃----+105℃ d﹒Resistance to solder heat：260℃.10 secs. 50sec max. Temperature ( ℃ ) Ⅳ﹒GENERAL SPECIFICATION： 200 150 70sec max. 100 50 0 AR-001A 230℃ 50 100 150 Time ( seconds ) 200 250 SPECIFICATION FOR APPROVAL REF : 20090903-A PROD. PAGE: 2 ABC'S DWG NO. SHIELDED SMD POWER INDUCTOR NAME SH6038□□□□L□-□□□ ABC'S ITEM NO. Ⅴ﹒ ELECTRICAL CHARACTERISTICS： DWG No. SH60383R3YL□ -□□□ SH60385R0YL□ -□□□ SH60386R2YL□ -□□□ SH60387R4YL□ -□□□ SH60388R7YL□ -□□□ SH6038100YL□ -□□□ SH6038120YL□ -□□□ SH6038150YL□ -□□□ SH6038180YL□ -□□□ SH6038220YL□ -□□□ SH6038270YL□ -□□□ SH6038330YL□ -□□□ SH6038390YL□ -□□□ SH6038470YL□ -□□□ SH6038560YL□ -□□□ SH6038680YL□ -□□□ SH6038820YL□ -□□□ SH6038101YL□ -□□□ 1). 2)."- Inductance ( μH ) 3.3 ±30％ 5.0 ±30％ 6.2 ±30％ 7.4 ±30％ 8.7 ±30％ 10.0 ±30％ 12.0 ±30％ 15.0 ±30％ 18.0 ±30％ 22.0 ±30％ 27.0 ±30％ 33.0 ±30％ 39.0 ±30％ 47.0 ±30％ 56.0 ±30％ 68.0 ±30％ 82.0 ±30％ 100.0 ±30％ ：Packaging Information… A：Bulk □□□ ":Reference code B ：Taping Reel 3). Inductance Test Freq. ：10KHz /0.1V 4). IDC base on Temp. rise 30 ℃ max. & △L/L0A=35% max. AR-001A RDC (Ω) max. 0.020 0.024 0.027 0.031 0.034 0.038 0.053 0.057 0.092 0.096 0.109 0.124 0.138 0.155 0.202 0.234 0.324 0.358 IDC (A) max. 3.50 2.90 2.50 2.30 2.20 2.00 1.70 1.60 1.50 1.30 1.20 1.10 1.00 0.95 0.85 0.75 0.70 0.65 SPECIFICATION FOR APPROVAL REF : 20090903-A PROD. PAGE: 3 NAME SH6038□□□□L□-□□□ ABC'S DWG NO. SHIELDED SMD POWER INDUCTOR ABC'S ITEM NO. Ⅵ﹒PACKAGING INFORMATION： ( 1 ) Configuration T Cover Tape N A B 2.0±0.5 ∮C ∮C D G Embossed carrier ※Carrier tape width : D P:12 m/m 4 m/m End Start 100 Leader no component 200 m/m min. 100 100 100 100 Trailer no component 400 m/m min. Components User direction of feed ( 2 ) Dimensions Unit:m/m Style A 13 - 16 330 B 21±0.8 C D 13±0.5 16 G 18 +0 N 50 -0 T 22.4 ( 3 ) Q'TY & G.W. Per package Inner : Reel Series SH6038 AR-001A Outer : Carton Q'TY (pcs) G.W. (gw) Style Q'TY (pcs) 1000 1500 13 - 16 6000 G.W. (Kg) 12.5 Size (cm) 40 x 40 x 24 SPECIFICATION FOR APPROVAL REF : 20090903-A PROD. NAME PAGE: 4 SH6038□□□□L□-□□□ ABC'S DWG NO. SHIELDED SMD POWER INDUCTOR ABC'S ITEM NO. Ⅶ﹒DWGING NUMBER EXPRESSION： S H 6 0 3 8 Reference code Appendix code 2 : Package Appendix code 1 : Classification Tolerance code Electrical code Dimension code Type code Appendix code 1：Product Classification L：Lead Free Standard products comply with RoHS' requirements 1 ~ 9：Lead Free Special products comply with RoHS' requirements Appendix code 2：Package Information Code AR-001A Inner package Inner package Q'TY A T.B.D. T.B.D. B T / R ( Reel package ) 1000 pcs Remark SPECIFICATION FOR APPROVAL REF : 20090903-A PROD. NAME PAGE: 5 SHIELDED SMD POWER INDUCTOR ABC'S DWG NO. SH6038□□□□L□-□□□ ABC'S ITEM NO. Ⅷ﹒RELIABILITY TEST： Test item Solderability Thermal shock test ( Temp. cycle ) Specification Test condition More than 95% of the terminal electrode Shall be covered With fresh solder. Preheat : 155 ℃ / 4 hours. Solder : Sn96.5 / Ag3 / Cu0.5 or equivalent Solder temp. : 235±5℃ Flux : Rosin Dip time : 5±0.5 seconds Electrical oharacteristics shall not change more than ±20% Room temp. 15 minutes -40 ℃ 30 minutes Room temp. 15 minutes +105 ℃ Total : 50 cycles Humidity test Temperature : 40±2℃ Humidity : 90±5% Time : 1000 hours High temp. Resistance test Temperature : 105±5℃ Applied current : Per spec. Time : 96 hours AR-001A 30 minutes SPECIFICATION FOR APPROVAL REF : 20090903-A PROD. NAME PAGE: 6 ABC'S DWG NO. SHIELDED SMD POWER INDUCTOR SH6038□□□□L□-□□□ ABC'S ITEM NO. Ⅸ﹒UL CARD： OBMW2 Magnet Wire-Component September 8, 2000 JUNG SHING WIRE CO LTD 231 CHUNG CHENG RD, SEC 3 JEN-TEH HSIANG, TAINAN HSIEN TAIWAN Mtl Dsg AIW CFUEWB EIAIW EILOCKY EILOCKW EIW EIW-2 FL.EILOCKY LSFFW LSUEW PEW PEY SF.FLW SF.EIW SF.BY@ SF.FLY@ SF.BLOCKBS SF.EILOCKY# SF.EILOCKBS SF.BW@ SFFW Mark Dsg ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ ____ BC Coat Typ Polyamideimide Polyurethane Polyesterimide Polyesterimide Polyesterimide Polyamideimide Polyamide Modified Epoxy ____ ____ Polyesterimide Polyesterimide Modified Polyester Polyurethane Polyurethane Polyester Polyester Modified Polyester Polyesterimide Modified Polyester Modified Polyester Modified Polyester Polyesterimide Polyesterimide Polyamide ____ ____ ____ ____Nylon ____ Nylon Nylon Modified Polyamide Polyamide Modified Polyamide ____ Modified Polyester Polyurethane 287806002 Mtl Dsg SFFY UEW-1 UEW-2 UEW-4 UEY UEY-2 OC ____ ____ E174837 ANSI Type Temp Class MW81-C MW75C MW35C ___ ___ 220 130 200 180 200 ___ MW74-C ___ MW79-C ___ ___ MW24-C MW26C MW77C MW27-C MW27-C ___ ___ ___ 180 180 MW26C MW79 ____ ____ ____ ____ ____ BC Coat Typ Polyurethane Polyurethane Polyurethane Polyurethane Polyurethane Polyurethane 155 155 A not-for-profit organization dedicated to public safety and committed to quality service Page 1 of 2 Mark Dsg ____ 220 200 155 155 130 155 155 155 180 155 155 155 OC Polyamide ____ ____ ____ Nylon Polyamide ANSI Type Temp Class MW80C MW2-C ___ 155 105 130 130 130 130 MW75C MW28-C MW28-C @-May be suffixed by LZ; # - May be suffixed by LZ, EL or LZI. LZ - Signifies magned wires twisted together; EL - signifies base coated magnet wire laid parallel with top coat applied overall; LZL - signifies base coated magnet wire twisted together and covered with top coat overall. Marking: Company name or trademarks Recognized Component Mark. or 榮星電線 , material designation or marked designation on packaed or reel, and See General Information Preceding These Recognitions For use only in equipment where the acceptability of the combination is determined by Underwriters Laboratories Inc. 287806002 AR-001A Page 2 of 2 OBMW2⁄E174837 September 8 , 2000