cs5373a new.fm

CS5373A
Low-power, High-performance ΔΣ Modulator and Test DAC
Modulator Features
Description
 Fourth-order ΔΣ Architecture
• Clock-jitter-tolerant architecture
• Input signal bandwidth: DC to 2 kHz
• Max AC amplitude: 5 Vpp differential
• Max DC amplitude: ± 2.5 Vdc differential
The CS5373A is a high-performance, fourth-order ΔΣ
modulator integrated with a ΔΣ digital-to-analog converter (DAC). When combined with a CS3301A/02A
differential amplifier and the CS5378 digital filter, a
small, low-power, self-testing, high-accuracy, singlechannel measurement system results.
 High Dynamic Range
• 127 dB SNR @ 215 Hz BW (2 ms sampling)
• 124 dB SNR @ 430 Hz BW (1 ms sampling)
 Low Total Harmonic Distortion
• -118 dB THD typical (0.000126%)
• -112 dB THD maximum (0.000251%)
 Low Power Consumption: 25 mW, 10 µW
Test DAC Features
 Digital ΔΣ Input from CS5378 Digital Filter
 Selectable Differential Analog Outputs
• Precision output (OUT±) for electronics tests
• Buffered output (BUF±) for sensor tests
 Multiple AC and DC Operational Modes
• Output signal bandwidth: DC to 100 Hz
• Max AC amplitude: 5 Vpp differential
• Max DC amplitude: + 2.5 Vdc differential
 Selectable Attenuation to Match CS3301A/02A
• 1, 1/2, 1/4, 1/8, 1/16, 1/32, 1/64
 Outstanding Performance
• OUT AC: -115 dB THD typical, -112 dB maximum
• BUF AC: -105 dB THD typical, -95 dB maximum
• OUT DC: Differential VREF ± 10 mV typical
• BUF DC: Differential VREF ± 25 mV typical
 Low Power Consumption
• AC modes / DC modes: 40 mW / 25 mW
• Sleep mode / Power down: 2.5 mW / 600 µW
The modulator has high dynamic range and low total harmonic distortion with very low power consumption. It
converts differential analog input signals from the
CS3301A/02A amplifier to an oversampled serial bit
stream at 512 kbits per second. This oversampled bit
stream is then decimated by the CS5378 digital filter to a
24-bit output at the selected output word rate.
The test DAC operates in either AC or DC test modes.
AC test modes measure system dynamic performance
through THD and CMRR tests while DC test modes are
for gain calibration and pulse tests. It has two sets of differential analog outputs, OUT and BUF, as dedicated
outputs for testing the electronics channel and for incircuit sensor tests. Output attenuation settings are
binary weighted and match the gain settings of the
CS3301A/02A differential amplifiers for full-scale testing
at all gain ranges.
ORDERING INFORMATION
See page 39.
VA+
VREF+
VREF-
VD
INR+
MDATA
24-Bit
ΔΣ
Modulator
INF+
INFINR-
MFLAG
MCLK
Clock
Generator
MSYNC
OUT+
TDATA
OUT-
Common Features
Attenuator
1/1 to 1/64
BUF+
 Extremely Small Footprint
• 28-pin SSOP package, 8 mm x 10 mm
 Bipolar Power Supply Configuration
• VA+ = +2.5 V; VA- = -2.5 V; VD = +3.3 V
http://www.cirrus.com
24-Bit
ΔΣ
Test DAC
CAP+
BUF-
CAP-
VA-
Copyright  Cirrus Logic, Inc. 2010
(All Rights Reserved)
ATT(0, 1, 2)
MODE(0, 1, 2)
GND
OCT ‘10
DS703F2
CS5373A
TABLE OF CONTENTS
1. CHARACTERISTICS AND SPECIFICATIONS ........................................................................ 4
SPECIFIED OPERATING CONDITIONS ................................................................................. 4
TEMPERATURE CONDITIONS ............................................................................................... 5
ABSOLUTE MAXIMUM RATINGS ........................................................................................... 5
ANALOG INPUT CHARACTERISTICS ................................................................................... 6
ANALOG OUTPUT CHARACTERISTICS ............................................................................... 7
MODULATOR CHARACTERISTICS ........................................................................................ 8
PERFORMANCE PLOTS ......................................................................................................... 9
DAC AC DIFFERENTIAL MODES 1, 2, 3............................................................................... 10
DAC AC DIFFERENTIAL MODES 1, 2, 3 (CONT.) ............................................................... 11
DIGITAL CHARACTERISTICS .............................................................................................. 15
DIGITAL CHARACTERISTICS (CONT.) ............................................................................... 16
DIGITAL CHARACTERISTICS (CONT.) ............................................................................ 17
POWER SUPPLY CHARACTERISTICS ................................................................................ 18
2. GENERAL DESCRIPTION ..................................................................................................... 19
2.1 Delta-Sigma Modulator .................................................................................................... 19
2.2 Digital-to-Analog Converter .............................................................................................. 19
3. SYSTEM DIAGRAM ............................................................................................................ 20
4. POWER MODES ..................................................................................................................... 21
4.1 Power Down ..................................................................................................................... 21
4.2 Sleep Mode ...................................................................................................................... 21
4.3 Modulator Mode ............................................................................................................... 21
4.4 AC Test Modes ................................................................................................................ 21
4.5 DC Test Modes ................................................................................................................ 21
5. OPERATIONAL MODES ........................................................................................................ 22
5.1 Modulator Mode ............................................................................................................... 22
5.1.1 Modulator One’s Density ..................................................................................... 22
5.1.2 Modulator Decimated Output .............................................................................. 22
5.1.3 Modulator Synchronization .................................................................................. 22
5.1.4 Modulator Idle Tones .......................................................................................... 23
5.1.5 Modulator Stability ............................................................................................... 23
5.2 AC Test Modes ................................................................................................................ 23
5.2.1 AC Differential ..................................................................................................... 23
5.2.2 AC Common Mode .............................................................................................. 24
5.2.3 DAC Stability ....................................................................................................... 24
5.3 DC Test Modes ................................................................................................................ 24
5.3.1 DC Common Mode ............................................................................................. 24
5.3.2 DC Differential ..................................................................................................... 25
5.4 Sleep Mode ...................................................................................................................... 25
6. DIGITAL SIGNALS ................................................................................................................. 26
6.1 MCLK Connection ............................................................................................................ 26
6.2 MSYNC Connection ......................................................................................................... 26
6.3 MDATA Connection ......................................................................................................... 27
6.4 MFLAG Connection ......................................................................................................... 27
6.5 TDATA Connection .......................................................................................................... 27
6.6 GPIO Connections ........................................................................................................... 27
7. ANALOG SIGNALS ................................................................................................................ 28
7.1 INR±, INF± Modulator Inputs ........................................................................................... 28
7.1.1 Modulator Input Impedance ................................................................................ 28
7.1.2 Modulator Anti-alias Filter ................................................................................... 28
7.2 DAC Output Attenuation .................................................................................................. 29
7.3 DAC OUT± Precision Output ........................................................................................... 29
7.4 DAC BUF± Buffered Output ............................................................................................. 30
2
DS703F2
CS5373A
7.5 DAC CAP± Connection ................................................................................................... 30
7.6 Analog Differential Signals .............................................................................................. 30
8. VOLTAGE REFERENCE ........................................................................................................ 31
8.1 VREF Power Supply ........................................................................................................ 31
8.2 VREF RC Filter ................................................................................................................ 31
8.3 VREF PCB Routing ......................................................................................................... 31
8.4 VREF Input Impedance ................................................................................................... 31
8.5 VREF Accuracy ............................................................................................................... 32
8.6 VREF Independence ....................................................................................................... 32
9. POWER SUPPLIES ................................................................................................................ 33
9.1 Power Supply Bypassing ................................................................................................. 33
9.2 PCB Layers and Routing ................................................................................................. 33
9.3 Power Supply Rejection .................................................................................................. 33
9.4 SCR Latch-up .................................................................................................................. 34
9.5 DC-DC Converters .......................................................................................................... 34
10. TERMINOLOGY ................................................................................................................... 35
11. PIN DESCRIPTION ............................................................................................................... 36
12. PACKAGE DIMENSIONS .................................................................................................... 38
13. ORDERING INFORMATION ............................................................................................... 39
14. ENVIRONMENTAL, MANUFACTURING, & HANDLING INFORMATION .......................... 39
15. REVISION HISTORY ........................................................................................................... 39
LIST OF FIGURES
Figure 1. Modulator Noise Performance ......................................................................................... 9
Figure 2. Modulator + Test DAC Dynamic Performance................................................................. 9
Figure 3. Digital Input Rise and Fall Times ................................................................................... 15
Figure 4. System Timing Diagram................................................................................................. 17
Figure 5. MCLK / MSYNC Timing Detail ....................................................................................... 17
Figure 6. CS5373A Block Diagram ............................................................................................... 19
Figure 8. Connection Diagram ...................................................................................................... 20
Figure 7. System Diagram ............................................................................................................ 20
Figure 9. Power Mode Diagram .................................................................................................... 21
Figure 10. AC Differential Modes .................................................................................................. 23
Figure 11. AC Common Mode ...................................................................................................... 24
Figure 12. DC Test Modes ............................................................................................................ 25
Figure 13. Digital Signals .............................................................................................................. 26
Figure 14. Analog Signals ............................................................................................................. 28
Figure 15. DAC Output Attenuation Settings ................................................................................ 29
Figure 16. Voltage Reference Circuit ............................................................................................ 31
Figure 17. Power Supply Diagram ................................................................................................ 33
LIST OF TABLES
Table 1. Selections for Operational Mode and DAC Attenuation .................................................... 4
Table 2. Operational Modes.......................................................................................................... 22
Table 3. Output Coding for the CS5373A Modulator and CS5378 Digital Filter Combination ...... 22
DS703F2
3
CS5373A
1. CHARACTERISTICS AND SPECIFICATIONS
•
Min / Max characteristics and specifications are guaranteed over the Specified Operating Conditions.
•
Typical performance characteristics and specifications are measured at nominal supply voltages and TA = 25°C.
•
GND = 0 V. Single-ended voltages with respect to GND, differential voltages with respect to opposite half.
•
Device is connected as shown in Figure 8 on page 20 unless otherwise noted.
SPECIFIED OPERATING CONDITIONS
Parameter
Symbol
Min
Nom
Max
Unit
VA+
2.45
2.50
2.55
V
VA-
-2.45
-2.50
-2.55
V
VD
3.20
3.30
3.40
V
(Note 2, 3)
VREF
-
2.500
-
V
(Note 4)
VREF-
-
VA -
-
V
TA
-40
25
85
°C
Bipolar Power Supplies
± 2%
(Note 1) ± 2%
± 3%
Positive Analog
Negative Analog
Positive Digital
Voltage Reference
{VREF+} - {VREF-}
VREFThermal
Ambient Operating Temperature
Industrial (-IS, -ISZ)
Notes: 1. VA- must always be the most-negative input voltage to avoid potential SCR latch-up conditions.
2. By design, a 2.500 V voltage reference input results in the best signal-to-noise performance.
3. Full-scale accuracy is directly proportional to the voltage reference absolute accuracy.
4. VREF inputs must satisfy: VA- < VREF- < VREF+ < VA+.
Modes of Operation
Selection
MODE
[2:0]
0
000
Modulator: enabled.
DAC: sleep.
1
001
DAC Attenuation
Selection
ATT[2:0]
Attenuation
dB
0
000
1/1
0 dB
1
001
1/2
-6.02 dB
Modulator: enabled.
DAC: AC OUT and BUF outputs.
2
010
1/4
-12.04 dB
3
0 11
1/8
-18.06 dB
Mode Description
2
010
Modulator: enabled.
DAC: AC OUT only, BUF high-z.
4
100
1/16
-24.08 dB
5
101
1/32
-30.10 dB
3
0 11
Modulator: enabled.
DAC: AC BUF only, OUT high-z.
6
11 0
1/64
-36.12 dB
4
100
Modulator: enabled.
DAC: DC common mode output.
7
111
reserved
reserved
5
101
Modulator: enabled.
DAC: DC differential output.
6
11 0
Modulator: enabled.
DAC: AC common mode output.
7
111
Modulator: sleep.
DAC: sleep.
Table 1. Selections for Operational Mode and DAC Attenuation
4
DS703F2
CS5373A
TEMPERATURE CONDITIONS
Parameter
Symbol
Min
Typ
Max
Unit
TA
-40
-
85
ºC
Storage Temperature Range
TSTR
-65
-
150
ºC
Allowable Junction Temperature
TJCT
-
-
125
ºC
Junction to Ambient Thermal Impedance (4-layer PCB)
ΘJA
-
65
-
ºC / W
Ambient Operating Temperature
ABSOLUTE MAXIMUM RATINGS
Parameter
DC Power Supplies
Positive Analog
Negative Analog
Digital
Symbol
Min
Max
Parameter
VA+
VAVD
-0.5
-6.8
-0.5
6.8
0.5
6.8
V
V
V
Analog Supply Differential
(VA+) - (VA-)
VADIFF
-
6.8
V
Digital Supply Differential
(VD) - (VA-)
VDDIFF
-
7.6
V
IPWR
-
mA
IIN
-
IOUT
-
±50
±10
±25
Power Dissipation
PDN
-
500
mW
Analog Input Voltages
VINA
(VA-) - 0.5
(VA+) + 0.5
V
Digital Input Voltages
VIND
-0.5
(VD) + 0.5
V
Input Current, Power Supplies
Input Current, Any Pin Except Supplies
Output Current
(Note 5)
(Note 5, 6)
(Note 5)
mA
mA
WARNING: Operation at or beyond these limits may result in permanent damage to the device.
Normal operation is not guaranteed at these extremes.
Notes: 5. Transient currents up to ±100 mA will not cause SCR latch-up.
6. Includes continuous over-voltage conditions at the modulator analog input pins.
DS703F2
5
CS5373A
ANALOG INPUT CHARACTERISTICS
Parameter
Symbol
Min
Typ
Max
Unit
VREF
-
2.500
-
V
VREF Input
{VREF+} - {VREF-}
(Note 2, 3)
VREF-
-
VA -
-
V
VREF Input Current, Modulator Only
VREF-
(Note 4)
VREFIMOD
-
120
-
µA
VREF Input Current, Modulator + DAC AC Mode
VREFIMAC
-
200
-
µA
VREF Input Current, Modulator + DAC DC Mode
VREFIMDC
-
160
-
µA
VREFIN
-
-
1
µVrms
RAA
CAA
-
680
20
-
Ω
nF
VREF Input Noise
(Note 7)
Modulator INR±, INF± Inputs
External Anti-alias Filter
(Note 8, 9)
Series Resistance
Differential Capacitance
Differential Input Impedance
INR±
INF±
ZDIFINR
ZDIFINF
-
20
1
-
kΩ
MΩ
Single-ended Input Impedance
INR±
INF±
ZSEINR
ZSEINF
-
40
2
-
kΩ
MΩ
CAA
-
10
-
nF
DAC CAP± Input
External Anti-alias Filter
(Note 9)
Differential Capacitance
Notes: 7. Maximum integrated noise over the measurement bandwidth for the voltage reference device attached
to the VREF± inputs.
8. The modulator analog inputs are normally driven by a CS3301A/02A amplifier.
9. Differential anti-alias capacitors are discrete external components and must be of good quality (C0G,
NPO, poly). Poor quality capacitors will degrade total harmonic distortion (THD) performance.
6
DS703F2
CS5373A
ANALOG OUTPUT CHARACTERISTICS
Parameter
Symbol
Min
Typ
Max
Unit
RLOUT
CLOUT
50
-
-
50
MΩ
pF
DAC Analog OUT± Output
Analog External Load at OUT±
(Note 10, 11)
Load Resistance
Load Capacitance
Differential Output Impedance
1/1
1/2
1/4
1/8
1/16
1/32
1/64
ZDIFOUT
-
1.4
10.1
7.9
5.1
3.3
2.3
1.7
-
kΩ
kΩ
kΩ
kΩ
kΩ
kΩ
kΩ
Single-ended Output Impedance
1/1
1/2
1/4
1/8
1/16
1/32
1/64
ZSEOUT
-
0.8
7.4
9.0
9.4
9.5
9.5
9.2
-
kΩ
kΩ
kΩ
kΩ
kΩ
kΩ
kΩ
High-Z Impedance
HZOUT
-
3
-
MΩ
Crosstalk to BUF± High-Z Output
XTOUT
-
-120
-
dB
RLBUF
CLBUF
1
-
-
2
kΩ
nF
1/1 - 1/64
ZDIFBUF
-
6
-
Ω
1/1 - 1/32
(Note 12) (BUF-) 1/64
(Note 12) (BUF+) 1/64
ZSEBUF
-
4
4
100
-
Ω
High-Z Impedance
HZBUF
-
4.5
-
MΩ
Crosstalk to OUT± High-Z Output
XTBUF
-
-120
-
dB
DAC Analog BUF± Output
Analog External Load at BUF±
(Note 10)
Differential Output Impedance
Single-ended Output Impedance
Load Resistance
Load Capacitance
Notes: 10. Guaranteed by design and/or characterization.
11. Load on the precision OUT± outputs is normally from a CS3301A/02A amplifier, which has 2 GΩ/1 TΩ
typical input impedance and 18 pF typical input capacitance.
12. Single-ended output impedance at 1/64 is different for BUF+ and BUF- due to the output attenuator
architecture.
DS703F2
7
CS5373A
MODULATOR CHARACTERISTICS
Parameter
Symbol
Min
Typ
Max
Unit
VBW
DC
-
1720
Hz
Input Characteristics
Input Signal Frequencies
(Note 10, 13)
Full Scale Differential AC Input
(Note 10)
VAC
-
-
5
Vpp
Full Scale Differential DC Input
(Note 10)
VDC
-2.5
-
2.5
Vdc
(Note 10, 14)
VRNG
(VA-)+0.7
-
(VA+)-1.25
V
(Note 15)
VCM
-
(VA-)+2.5
-
V
Dynamic Range
(Note 16)
DC to 1720 Hz
DC to 860 Hz
DC to 430 Hz
DC to 215 Hz
DC to 108 Hz
DC to 54 Hz
DC to 27 Hz
SNR
121
-
109
121
124
127
130
133
136
-
dB
dB
dB
dB
dB
dB
dB
Signal Dependent Noise
(Note 17, 18)
DC to 430 Hz
SDN
100
110
-
dB
Total Harmonic Distortion
(Note 18)
THD
-
-118
-112
dB
Linearity
(Note 18)
LIN
-
0.000126
0.000251
%
CMRR
-
90
-
dB
(Note 3)
CGA
-
±1
±2
%
(Note 19)
CGATC
-
5
-
ppm/°C
OFST
-
100
-
mV
OFSTTC
-
0.1
-
μV/°C
-
±1
-
μV
-
100
-
%FS
Input Voltage Range (Signal + Vcm)
Input Common Mode Voltage
Dynamic Performance
Common Mode Rejection Ratio
Gain Accuracy
Channel to Channel Gain Accuracy
Channel Gain Drift
Offset
Offset Voltage, Differential
Offset Voltage Drift
(Note 19)
Offset after Calibration
(Note 20) OFSTCAL
(Note 21) OFSTRNG
Offset Calibration Range
Notes: 13. The upper bandwidth limit is determined by the CS5378 digital filter cut-off frequency.
14. No signals operating from external power supplies should be applied to pins of the device prior to its
own supplies being established. Connecting any terminal to voltages greater than VA+ or less than VAmay cause destructive latch-up.
15. Common mode voltage is defined as the mid-point of the differential signal.
16. Dynamic Range defined as 20 log [ (RMS full scale) / (RMS idle noise) ] where idle noise is measured
from a CS3301A/02A amplifier terminated input at 1x gain.
17. Signal Dependent Noise defined as 20 log [ (RMS full scale) / (RMS signal noise) ] where signal noise
is measured by subtracting the signal power at the fundamental and harmonic frequencies.
18. Tested with a 31.25 Hz sine wave at -1 dB amplitude.
19. Specification is for the parameter over the specified temperature range and is for the device only. It does
not include the effects of external components.
20. This specification applies to the effective offset voltage calculated from the output codes of the CS5378
digital filter following offset calibration and correction.
21. Offset calibration is performed in the CS5378 digital filter and includes the full-scale signal range.
8
DS703F2
CS5373A
PERFORMANCE PLOTS
Figure 1. Modulator Noise Performance
Figure 2. Modulator + Test DAC Dynamic Performance
DS703F2
9
CS5373A
DAC AC DIFFERENTIAL MODES 1, 2, 3
Parameter
Symbol
Min
Typ
Max
Unit
VACFS
-
5
2.5
1.25
625
312.5
156.25
78.125
-
Vpp
Vpp
Vpp
mVpp
mVpp
mVpp
mVpp
AC Differential Characteristics
Full-scale Differential AC Output
Full-scale Bandwidth
1/1
1/2
1/4
1/8
1/16
1/32
1/64
(Note 10)
VACBW
-
-
100
Hz
(Note 10, 22)
VACIMP
-
-
-20
dBfs
(Note 3, 23)
VACABS
-
+1
+2
%FS
Relative Accuracy
(Note 24)
VACREL
-
+1
+2
%FS
Full-scale Drift
(Note 19)
VACTC
-
8
-
μV/°C
(Note 15)
VACCM
-
(VA-)+2.35
-
V
-
2
-
μV/°C
Impulse Amplitude
AC Differential Accuracy
Full-scale Accuracy
DC Common Mode Characteristics
Common Mode
Common Mode Drift
(Note 15, 19) VACCMTC
Notes: 22. Maximum amplitude for DAC operation above 100 Hz. A reduced amplitude for higher frequencies is
required to guarantee stability of the low-power ΔΣ DAC architecture.
23. Full-scale accuracy tests the matching of 1/1 attenuation across multiple devices.
24. Relative accuracy tests the tracking of 1/1,1/2,1/4,1/16,1/32,1/64 attenuation relative to 1/8 attenuation
on a single device.
10
DS703F2
CS5373A
DAC AC DIFFERENTIAL MODES 1, 2, 3 (CONT.)
Parameter
Symbol
Min
Typ
Max
Unit
Signal to Noise
Signal to Noise (OUT± Unloaded)
(Note 25)
1/1
1/2
1/4
1/8
1/16
1/32
1/64
SNROUT
110
-
114
114
114
113
111
107
102
-
dB
dB
dB
dB
dB
dB
dB
Signal to Noise (BUF± Unloaded)
(Note 25, 26)
1/1
1/2
1/4
1/8
1/16
1/32
1/64
SNRBUF
100
-
111
107
102
96
90
84
78
-
dB
dB
dB
dB
dB
dB
dB
Signal to Noise (BUF± 1 kΩ load)
(Note 25, 26)
1/1
SNRBUFL
100
110
-
dB
Total Harmonic Distortion (OUT± Unloaded)
(Note 18, 27)
1/1
1/2
1/4
1/8
1/16
1/32
1/64
THDOUT
-
-115
-118
-116
-111
-109
-107
-101
-112
-
dB
dB
dB
dB
dB
dB
dB
Total Harmonic Distortion (BUF± Unloaded)
(Note 18, 26, 27)
1/1
1/2
1/4
1/8
1/16
1/32
1/64
THDBUF
-
-111
-107
-102
-97
-92
-86
-80
-95
-
dB
dB
dB
dB
dB
dB
dB
Total Harmonic Distortion (BUF± 1 kΩ load)
(Note 18, 26, 27)
1/1
THDBUFL
-
-95
-85
dB
Total Harmonic Distortion
Notes: 25. Specification measured using CS3301A amplifier at corresponding gain with the modulator measuring
a 400 Hz bandwidth. Amplified noise dominates for x16, x32, x64 amplifier gains.
26. Buffered outputs (BUF±) include 1/f noise not present on the precision outputs (OUT±).
27. Specification measured using CS3301A amplifier at corresponding gain using the modulator measuring
a 400 Hz bandwidth. Amplified noise in the harmonic bins dominates THD measurements for x16, x32,
x64 amplifier gains.
DS703F2
11
CS5373A
DAC DC COMMON MODE 4
Parameter
Symbol
Min
Typ
Max
Unit
VDCCM
-
(VA-)+2.35
-
V
(Note 19) VDCCMTC
-
2
-
μV/°C
Common Mode Match (OUT±)
VDCCMM
-
+10
-
mV
Common Mode Match (BUF±)
VDCCMM
-
+25
-
mV
DC Common Mode Characteristics
Common Mode Output
Common Mode Drift
DC Common Mode Accuracy
Noise
Noise (OUT± Unloaded)
(Note 25)
1/1
1/2
1/4
1/8
1/16
1/32
1/64
NOUT
-
4.4
5.6
5.6
5.6
5.6
9.9
17.7
-
μVrms
μVrms
μVrms
μVrms
μVrms
μVrms
μVrms
Noise (BUF± Unloaded)
(Note 25, 26)
1/1
1/2
1/4
1/8
1/16
1/32
1/64
NBUF
-
5.6
8.9
12.5
28.0
55.9
99.4
198.3
-
μVrms
μVrms
μVrms
μVrms
μVrms
μVrms
μVrms
Noise (BUF± 1 kΩ load)
(Note 25, 26)
1/1
NBUFL
-
5.6
-
μVrms
12
DS703F2
CS5373A
DAC DC DIFFERENTIAL MODE 5
Parameter
Symbol
Min
Typ
Max
Unit
VDCFS
-
2.5
1.25
625
312.5
156.25
78.125
39.0625
-
V
V
mV
mV
mV
mV
mV
DC Differential Mode Characteristics
Full-scale Differential DC Output
(Note 28)
1/1
1/2
1/4
1/8
1/16
1/32
1/64
DC Differential Accuracy
Full-scale Accuracy (OUT±)
(Note 3, 23)
VDCOUT
-
VREF +10
-
mV
Full-scale Accuracy (BUF±)
(Note 3, 23)
VDCBUF
-
VREF +25
-
mV
Relative Accuracy
(Note 24)
VDCREL
-
+1
-
%FS
Full-scale Drift
(Note 19)
VDCTC
-
8
-
μV/°C
(Note 15)
VDCCM
-
(VA-)+2.35
-
V
-
2
-
μV/°C
DC Common Mode Characteristics
Common Mode
Common Mode Drift
(Note 15, 19) VDCCMTC
Noise
Noise (OUT± Unloaded)
(Note 25, 28)
1/1
1/2
1/4
1/8
1/16
1/32
1/64
NOUT
-
6.3
6.3
7.0
7.0
7.0
8.9
12.5
-
μVrms
μVrms
μVrms
μVrms
μVrms
μVrms
μVrms
Noise (BUF± Unloaded)
(Note 25, 26, 28)
1/1
1/2
1/4
1/8
1/16
1/32
1/64
NBUF
-
9.9
11.2
15.8
28.0
55.9
99.4
198.3
-
μVrms
μVrms
μVrms
μVrms
μVrms
μVrms
μVrms
Noise (BUF± 1 kΩ load)
(Note 25, 26, 28)
1/1
NBUFL
-
9.9
-
μVrms
Notes: 28. DC differential output is chopper stabilized and includes low-level 32 kHz out-of-band noise which is
rejected by the digital filter.
DS703F2
13
CS5373A
DAC AC COMMON MODE 6
Parameter
Symbol
Min
Typ
Max
Unit
VCMFS
-
2.5
1.25
625
312.5
156.25
78.125
-
Vpp
Vpp
mVpp
mVpp
mVpp
mVpp
AC Common Mode Characteristics
Full-scale Common Mode AC Output
(Note 29)
Full-scale Bandwidth
1/1
1/2
1/4
1/8
1/16
1/32
(Note 10)
VCMBW
-
-
100
Hz
(Note 10, 22)
VCMIMP
-
-
-20
dBfs
Common Mode Match (OUT± Unloaded)
(Note 18, 27, 29)
1/1 - 1/32
VCMCMM
-
-110
-
dB
Common Mode Match (BUF± Unloaded)
(Note 18, 26, 27, 29)
1/1 - 1/32
VCMCMM
-
-90
-
dB
Common Mode Match (BUF± 1 kΩ load)
(Note 18, 26, 29)
1/1
VCMCMM
-
-90
-
dB
(Note 3, 23)
VCMABS
-
+1
-
%FS
Relative Accuracy
(Note 24)
VCMREL
-
+1
-
%FS
Full-scale Drift
(Note 19)
VCMTC
-
8
-
μV/°C
(Note 30)
VCMCM
-
(VA-)+2.35
-
V
-
2
-
μV/°C
Impulse Amplitude
AC Common Mode Accuracy
Full-scale Accuracy
DC Common Mode Characteristics
Common Mode Mean
Common Mode Mean Drift
(Note 19, 30) VCMCMTC
Notes: 29. No AC common mode signal is output at 1/64 attenuation due to the attenuator architecture.
30. Common mode mean is defined as the midpoint between AC common mode peaks.
14
DS703F2
CS5373A
DIGITAL CHARACTERISTICS
Parameter
Symbol
Min
Typ
Max
Unit
-
VD
V
Digital Inputs
High-level Input Voltage
(Note 10, 31)
VIH
0.6*VD
Low-level Input Voltage
(Note 10, 31)
VIL
0.0
-
0.8
V
Input Leakage Current
IIN
-
±1
±10
μA
Digital Input Capacitance
CIN
-
9
-
pF
Input Rise Times Except MCLK
(Note 10)
tRISE
-
-
100
ns
Input Fall Times Except MCLK
(Note 10)
tFALL
-
-
100
ns
High-level Output Voltage, Iout = -40 μA
(Note 10)
VOH
VD-0.3
-
-
V
Low-level Output Voltage, Iout = 40 μA
(Note 10)
VOL
-
-
0.3
V
IOZ
-
-
±10
μA
COUT
-
9
-
pF
Digital Outputs
High-Z Leakage Current
Digital Output Capacitance
Output Rise Times
(Note 10)
tRISE
-
-
100
ns
Output Fall Times
(Note 10)
tFALL
-
-
100
ns
Notes: 31. Device is intended to be driven with CMOS logic levels.
t rise
t fall
0.9 * VD
0.1 * VD
Figure 3. Digital Input Rise and Fall Times
DS703F2
15
CS5373A
DIGITAL CHARACTERISTICS (CONT.)
Parameter
Symbol
Min
Typ
Max
Unit
fCLK
-
2.048
-
MHz
Master Clock Input
MCLK Frequency
(Note 32)
MCLK Period
(Note 32)
tmclk
-
488
-
ns
MCLK Duty Cycle
(Note 10)
MCLKDC
40
-
60
%
MCLK Rise Time
(Note 10)
tRISE
-
-
50
ns
MCLK Fall Time
(Note 10)
tFALL
-
-
50
ns
MCLK Jitter (In-band or aliased in-band)
(Note 10)
MCLKIBJ
-
-
300
ps
MCLK Jitter (Out-of-band)
(Note 10) MCLKOBJ
-
-
1
ns
Master Sync Input
MSYNC Setup Time to MCLK Rising
(Note 10, 33)
tmss
20
122
-
ns
MSYNC Period
(Note 10, 33)
tmsync
40
976
-
ns
MSYNC Hold Time after MCLK Falling
(Note 10, 33)
tmsh
20
122
-
ns
(Note 34)
ttdata
-
1220
-
ns
fmdata
-
512
-
kbits/s
MDATA Output One’s Density Range
(Note 10)
MDATOD
14
-
86
%
Full-scale Output Code
(Note 35)
MDATFS
0xA2EAAE
-
0x5D1C41
MSYNC Instant to TDATA Start
MDATA Output
MDATA Output Bit Rate
TDATA Input
TDATA Input Bit Rate
(Note 36)
ftdata
-
256
-
kbits/s
TDATA Input One’s Density Range
(Note 10)
TBSOD
25
-
75
%
TBSGAIN Full-scale Code
(Note 37)
TBSFS
-
0x04B8F2
-
TBSGAIN -20 dB Code
(Note 37)
TBS-20dB
-
0x0078E5
-
Notes: 32. MCLK is generated by the CS5378 digital filter. If MCLK is disabled, the device automatically enters a
power-down state.
33. MSYNC is generated by the CS5378 digital filter and is latched on MCLK rising edge, synchronization
instant (t0) on next MCLK rising edge.
34. TDATA can be delayed from 0 to 63 full bit periods by the test bit stream generator in the CS5378 digital
filter. The timing diagrams show no TBSDATA delay.
35. Decimated, filtered, and offset corrected 24-bit output word from the CS5378 digital filter.
36. TDATA is generated by the test bit stream generator in the CS5378 digital filter.
37. TBSGAIN register value in the CS5378 digital filter.
16
DS703F2
CS5373A
DIGITAL CHARACTERISTICS (CONT.)
SYNC
MCLK
(2.048 MHz)
MSYNC
t0
MDATA
(512 kHz)
MFLAG
TDATA
(256 kHz)
Figure 4. System Timing Diagram
MCLK
(2.048 MHz)
MSYNC
tmss
tmsh
tmclk
t0
tmsync
MDATA
(2.048 MHz)
MFLAG
ttdata
TDATA
(256 kHz)
Figure 5. MCLK / MSYNC Timing Detail
DS703F2
17
CS5373A
POWER SUPPLY CHARACTERISTICS
Parameter
Symbol
Min
Typ
Max
Unit
Modulator Power Supply Current
Analog Power Supply Current
(Note 38)
IA
-
5
7
mA
Digital Power Supply Current
(Note 38)
ID
-
200
300
μA
DAC AC Mode Supply Current
Analog Power Supply Current
(Note 38)
IA
-
7.8
10
mA
Digital Power Supply Current
(Note 38)
ID
-
200
-
μA
Analog Power Supply Current
(Note 38)
IA
-
4.8
-
mA
Digital Power Supply Current
(Note 38)
ID
-
200
-
μA
Analog Power Supply Current
(Note 38)
IA
-
200
-
μA
Digital Power Supply Current
(Note 38)
ID
-
20
-
μA
Analog Power Supply Current
(Note 38)
IA
-
400
-
μA
Digital Power Supply Current
(Note 38)
ID
-
100
-
μA
DAC DC Mode Supply Current
Modulator Sleep Current
DAC Sleep Current
Power Down Current (MCLK = 0)
Analog Power Supply Current
(Note 38)
IA
-
100
-
μA
Digital Power Supply Current
(Note 38)
ID
-
20
-
μA
Time to Enter Power Down (MCLK disabled)
(Note 10)
PDTC
-
40
-
μS
(Note 39)
PSRR
-
90
-
dB
Power Supply Rejection
Power Supply Rejection Ratio
Notes: 38. All outputs unloaded. Digital inputs forced to VD or GND respectively.
39. Power supply rejection is characterized by applying a 100 mVp-p 50-Hz sine wave to each supply.
18
DS703F2
CS5373A
VA+
VREF+
VREF-
VD
INR+
MDATA
24-Bit
ΔΣ
Modulator
INF+
INFINR-
MFLAG
MCLK
Clock
Generator
MSYNC
OUT+
TDATA
OUT-
Attenuator
1/1 to 1/64
BUF+
24-Bit
ΔΣ
Test DAC
CAP+
CAP-
BUF-
VA-
ATT(0, 1, 2)
MODE(0, 1, 2)
GND
Figure 6. CS5373A Block Diagram
2. GENERAL DESCRIPTION
The CS5373A is a high-performance, fourthorder ΔΣ modulator integrated with a digital-toanalog converter (DAC). When combined with
a CS3301A/02A differential amplifier and the
CS5378 digital filter, a small low-power selftesting high-accuracy single-channel measurement system results.
2.1 Delta-Sigma Modulator
The CS5373A modulator has high dynamic
range and low total harmonic distortion with
very low power consumption, and is optimized
for extremely high-resolution measurement of
5 Vpp or smaller differential signals. It converts
analog input signals between DC and 1720 Hz
to an oversampled serial bit stream at
512 kbits per second.
The CS5378 digital filter generates the clock
and synchronization inputs for the modulator
while receiving the modulator one-bit data and
over-range flag outputs. The digital filter then
decimates the modulator’s oversampled output bit stream to a 24-bit output at the selected
output word rate.
2.2 Digital-to-Analog Converter
The CS5373A test DAC is driven by a digital
ΔΣ bit stream from the CS5378 digital filter’s
test bit stream (TBS) generator and operates
in either AC or DC test modes. AC test modes
DS703F2
(MODE 1, 2, 3, 6) are used to measure system THD and CMRR performance. DC test
modes (MODE 4, 5) are for gain calibration
and pulse tests. The digital filter also provides
clock and syncronization signals as well as
GPIO control signals to set the operational
mode and analog output attenuation.
Two sets of differential analog outputs, OUT
and BUF, simplify system design as dedicated
outputs for testing the electronics channel and
for in-circuit sensor tests. Output attenuator
settings are binary weighted (1, 1/2, 1/4, 1/8,
1/16, 1/32, 1/64) and match the CS3301A/02A
amplifier input levels for full-scale testing at all
gain ranges.
For maximum performance, the precision outputs (OUT±) must drive only high-impedance
loads such as the CS3301A/02A amplifier inputs. The buffered outputs (BUF±) can drive
lower-impedance loads, down to 1 kΩ, but with
reduced performance compared to the precision outputs.
The test DAC is optimized for low-power operation and has a restricted operational bandwidth in the AC modes. For stable operation,
full-scale AC test signals must not contain frequencies above 100 Hz. AC test signals above
100 Hz (TBS impulse mode, for example)
must have a -20 dB reduced amplitude to ensure stability of the low-power ΔΣ architecture.
19
CS5373A
3. SYSTEM DIAGRAM
System
Telemetry
Geophone
or
Hydrophone
Sensor
CS3301A
CS3302A
M
U
X
μController
or
Configuration
EEPROM
CS5373A
CS5378
680 Ω
20 nF
C0G
AMP
ΔΣ
Modulator
and
Test DAC
680 Ω
Digital Filter
w/ PLL
Communication
Interface
Figure 7. System Diagram
VA+
0 .1µF
0. 1µF
VA +
ELECTRONICS
TEST OUTPUT
VA+
2.5 V
VREF
Route OUT as diff pair
10 Ω
100 µF
+
CS5378
SIGNALS
CAP -
Route BUF as diff pair
SENSOR
TEST OUTPUT
VD
CAP +
10 nF
C0 G
BUF+
M ODE0
GPIO
BUF-
M ODE1
GPIO
M ODE2
GPIO
OUT+
ATT 0
GPIO
OUT-
ATT 1
GPIO
ATT 2
GPIO
CS5373A
Route VREF as diff pair
VREF +
VREF -
VA680 Ω
INPUT FROM
CS 3301 A/02 A
AMPLIFIER
680 Ω
680 Ω
*Populate with 2 x 10 nF or
1 x 22 nF C0 G or better .
*
20 nF
C0 G
*
TDATA
MCLK
INR+
20 nF
C0G
VD
TBSDATA
MCLK
MSYNC
MSYNC
MDATA
MDATA
M FLAG
MFLAG
INF+
INFINR-
680 Ω
VA VA-
GND
0.1 µF
Figure 8. Connection Diagram
20
DS703F2
CS5373A
POWER DOWN
MCLK = OFF
MODE = XXX
SLEEP MODE
MCLK = ON
MODE = 7
MODULATOR MODE
MCLK = ON
MODE = 0
AC TEST MODES
MCLK = ON
MODE = 1, 2, 3, 6
DC TEST MODES
MCLK = ON
MODE = 4, 5
Figure 9. Power Mode Diagram
4. POWER MODES
The CS5373A has five power modes. Modulator mode, AC test modes, and DC test modes
are operational modes, while power down and
sleep mode are non-operational standby
modes.
4.1 Power Down
If MCLK is stopped, an internal loss-of-clock
detection circuit automatically places the
CS5373A into power down. Power down is independent of the MODE and ATT pin settings,
and is automatically invoked after approximately 40 µs without an incoming MCLK edge.
In power down the modulator, AC test circuitry
and DC test circuitry are inactive and all outputs are high impedance. When used with the
CS5378 digital filter, the CS5373A is in power
down immediately after reset since MCLK is
disabled by default.
4.2 Sleep Mode
With MCLK active, selecting sleep mode
(MODE 7) places the CS5373A into a micropower sleep state. In sleep mode the modulator, AC test circuitry and DC test circuitry are
inactive and all outputs are high impedance.
(MODE 0) enables the CS5373A modulator
and places the AC and DC test circuitry into a
micro-power sleep state with the analog test
outputs high impedance. Following completion
of AC and DC system self-tests, the CS5373A
is typically set into modulator mode for normal
data acquisition.
4.4 AC Test Modes
With MCLK and TDATA active, selecting an
AC test mode (MODE 1, 2, 3, 6) enables the
modulator and causes the DAC to output AC
waveforms on the analog test outputs. AC test
modes use the low-power ΔΣ DAC circuitry in
the CS5373A to create precision differential or
common mode analog AC output signals from
the encoded digital test bit stream (TBS) input.
4.5 DC Test Modes
With MCLK active, selecting a DC test mode
(MODE 4, 5) enables the modulator and
causes the DAC to generate precision DC voltages on the analog test outputs. DC test
modes use switch-capacitor level-shifting buffer circuitry in the CS5373A to create differential or common mode DC analog output
voltages from the voltage reference input.
4.3 Modulator Mode
With MCLK active, selecting modulator mode
DS703F2
21
CS5373A
5. OPERATIONAL MODES
The CS5373A has seven operational modes
and one sleep mode selected by the MODE2,
MODE1, and MODE0 pins.
Modes of Operation
Selection
MODE
[2:0]
0
000
Modulator: enabled.
DAC: sleep.
1
001
Modulator: enabled.
DAC: AC OUT and BUF outputs.
2
010
Modulator: enabled.
DAC: AC OUT only, BUF high-z.
3
0 11
Modulator: enabled.
DAC: AC BUF only, OUT high-z.
4
100
Modulator: enabled.
DAC: DC common mode output.
5
101
Modulator: enabled.
DAC: DC differential output.
6
11 0
Modulator: enabled.
DAC: AC common mode output.
7
111
Modulator: sleep.
DAC: sleep.
Mode Description
Table 2. Operational Modes
5.1 Modulator Mode
Modulator mode (MODE 0) enables the ΔΣ
modulator and disables the DAC AC and DC
test circuitry to save power. This mode is used
for normal sensor measurements after selftests are completed.
5.1.1
Modulator One’s Density
In modulator mode (and whenever the modulator is enabled) the differential analog input
signal is converted to an oversampled ΔΣ serial bit stream on the MDATA output, with a
one’s density proportional to the differential
amplitude of the analog input signal.
One’s density of the MDATA output is defined
as the ratio of ‘1’ bits to total bits in the serial
22
bit stream output, i.e. an 86% one’s density
has, on average, a ‘1’ value in 86 of every 100
output data bits. The MDATA output has a
nominal 50% one’s density for a mid-scale differential input, approximately 86% one’s density for a positive full-scale input, and
approximately 14% one’s density for a negative full-scale input.
5.1.2
Modulator Decimated Output
When the CS5373A modulator operates with
the CS5378 digital filter, the final decimated,
24-bit, full-scale output code range depends if
digital offset correction is enabled. With digital
offset correction enabled, amplifier offset and
the modulator internal offset are removed from
the final conversion result.
Modulator
Differential Analog
Input Signal
> + (VREF + 5%)
CS5378 Digital Filter
Output Code
Offset
Corrected
+100 mV
Offset
Error Flag Possible
+ VREF
5D1C41
60D5B4
0V
000000
03B973
- VREF
A2EAAE
A6A421
> - (VREF + 5%)
Error Flag Possible
Table 3. Output Coding for the CS5373A
Modulator and CS5378 Digital Filter Combination
5.1.3
Modulator Synchronization
The modulator is designed to operate synchronously with other modulators in a measurement network, so a rising edge on the MSYNC
input resets the internal conversion state machine to synchronize analog sample timing.
MSYNC is automatically generated by the
CS5378 digital filter after receiving a synchronization signal from the external system, and
is chip-to-chip accurate within ± 1 MCLK period.
DS703F2
CS5373A
5.1.4
Modulator Idle Tones
The CS5373A modulator is ΔΣ type and so can
produce ‘idle tones’ in the measurement bandwidth when the differential input signal is a
steady-state DC signal within ± 50 mV of midscale. Idle tones result from low-frequency
patterns in the output bit stream and appear in
the measurement spectrum as small tones
about -135 dB down from full scale.
Idle tones are eliminated within the CS5373A
modulator by automatically adding +100 mV of
internal differential offset during conversion to
push idle tones out of the measurement bandwidth. Care should be taken to ensure external
offset voltages do not negate the internally
added differential offset.
differential or common mode analog AC signals by the CS5373A’s test DAC.
5.2.1
AC Differential
The first three AC test modes (MODE 1, 2, 3)
enable the modulator and AC test circuitry to
create precision differential analog signals for
THD and impulse testing of the measurement
channel. In mode 1, both sets of differential analog outputs (OUT and BUF) are enabled. In
mode 2 only the OUT analog output is enabled, and the BUF output is high impedance.
In mode 3 only the BUF analog output is enabled, and the OUT output is high impedance.
OUT+
5.1.5
Modulator Stability
The CS5373A’s ΔΣ modulator has a 4th order
architecture which is conditionally stable and
may go into an oscillatory condition if the analog inputs are over-ranged more than 5% past
either positive or negative full scale.
If an unstable condition is detected, the modulator collapses to a 1st order system and transitions the MFLAG output low-to-high to signal
an error condition to the CS5378 digital filter.
The analog input signal must be reduced to
within the full-scale range for at least 32 MCLK
cycles for the modulator to recover from an oscillatory condition. If the analog input remains
over-ranged for an extended period, the modulator will cycle between 4th order and 1st order operation and the MFLAG output will be
seen to pulse.
OUT-
CS5373A
MODE 1
BUF+
BUF-
OUT+
OUT-
DS703F2
Maximum
5 Vpp
Differential
Maximum
5 Vpp
Differential
CS5373A
MODE 2
BUF+
BUF-
OUT+
OUT-
5.2 AC Test Modes
AC test modes (MODE 1, 2, 3, 6) enable the
modulator and use the digital test bit stream
(TBS) input from the CS5378 digital filter to
construct analog AC waveforms. The digital bit
stream input to the TDATA pin encodes the
analog waveform as over-sampled one-bit ΔΣ
data, which is then converted into precision
Maximum
5 Vpp
Differential
High
Impedance
High
Impedance
CS5373A
MODE 3
BUF+
BUF-
Maximum
5 Vpp
Differential
Figure 10. AC Differential Modes
23
CS5373A
Differential AC test signals out of the CS5373A
consist of two halves with equal but opposite
magnitude, varying about a common mode
voltage. A full-scale 5 VPP differential AC signal centered on a -0.15 V common mode voltage will have:
SIG+ = -0.15 V + 1.25 V = +1.1 V
SIG- = -0.15 V - 1.25 V = -1.4 V
SIG+ is +2.5 V relative to SIGFor the opposite case:
SIG+ = -0.15 V - 1.25 V = -1.4 V
SIG- = -0.15 V + 1.25 V = +1.1 V
SIG+ is -2.5 V relative to SIGSo the total swing for SIG+ relative to SIG- is
(+2.5 V) - (-2.5 V) = 5 Vpp differential. A similar
calculation can be done for SIG- relative to
SIG+. It’s important to note that a 5 Vpp differential signal centered on a -0.15 V common
mode voltage never exceeds +1.1 V with respect to ground and never drops below -1.4 V
with respect to ground on either half. By definition, differential voltages are measured with
respect to the opposite half, not relative to
ground. A voltmeter differentially measuring
between SIG+ and SIG- in the above example
would correctly read 1.767 Vrms, or 5 Vpp.
5.2.2
AC Common Mode
The final AC test mode (MODE 6) enables the
modulator and AC test circuitry to create a
matched AC common mode analog signal for
CMRR testing of the measurement channel. In
OUT+
OUT-
Maximum
2.5 Vpp
Common
Mode
CS5373A
MODE 6
BUF+
BUF-
Figure 11. AC Common Mode
24
Maximum
2.5 Vpp
Common
Mode
mode 6, both sets of analog outputs (OUT and
BUF) are enabled. There is no AC common
mode output for an attenuator setting of 1/64.
Gross leakage in the sensor channel can be
detected by applying a full-scale AC common
mode signal. If there is a significant differential
mismatch in the channel due to sensor leakage, the AC common mode signal will be converted to a measurable differential signal at
the fundamental frequency.
5.2.3
DAC Stability
For the CS5373A’s low-power ΔΣ DAC architecture to remain stable, the TDATA input bit
stream should only encode 100 Hz or lower
bandwidth analog signals. For TDATA bit
stream frequencies above 100 Hz (for example, TBS impulse mode), the encoded amplitude must be reduced -20 dB below full scale
to guarantee stability.
If the CS5373A’s low-power ΔΣ DAC architecture becomes unstable, persistent elevated
noise will be present on the analog outputs
and AC linearity will be poor. To recover stability, place the CS5373A into power down or
sleep mode and restart the CS5378 test bit
stream generator before placing the CS5373A
back into an AC test mode.
5.3 DC Test Modes
DC test modes enable the modulator and DC
test circuitry to create precision level-shifted
and buffered versions of the voltage reference
input as precision DC common mode and DC
differential analog outputs. The absolute accuracy of the DC test modes is highly dependent
on the absolute accuracy of the voltage reference input voltage.
5.3.1
DC Common Mode
The first DC test mode (MODE 4) enables the
modulator and DC test circuitry to create a
matched DC common mode analog output
voltage as a baseline measurement for gain
DS703F2
CS5373A
calibration and differential pulse tests. In mode
4, both sets of analog outputs (OUT and BUF)
are enabled.
5.3.2
DC Differential
The second DC test mode (MODE 5) enables
the modulator and DC test circuitry to create a
precision differential DC analog output voltage
as the final measurement for gain calibration
and as the step/pulse output for differential
pulse tests. In mode 5, both sets of analog outputs (OUT and BUF) are enabled.
In DC differential mode (MODE 5) the levelshifting buffer circuitry adds low-level 32 kHz
switched-capacitor noise to the DC output.
This noise is out of the measurement bandwidth for systems designed with a
CS3301A/02A amplifier and CS5373A modulator and is rejected by the CS5378 digital filter. This 32 kHz switched-capacitor noise
does not affect DC system tests, though it may
be visible on an oscilloscope at high gain levels.
By
measuring
both
DC
test
OUT+
OUT-
modes
Approx
-0.15 VDC
Common
Mode
CS5373A
MODE 4
BUF+
BUF-
OUT+
OUT-
Approx
-0.15 VDC
Common
Mode
Maximum
2.5 VDC
Differential
CS5373A
MODE 5
BUF+
BUF-
Figure 12. DC Test Modes
DS703F2
Maximum
2.5 VDC
Differential
(MODE 4, 5), precision gain-calibration coefficients can be calculated for the measurement
channel. By first measuring the differential offset of the DC common mode output (MODE 4)
and then measuring the DC differential mode
amplitude (MODE 5), a precise offset-corrected, volts-to-codes conversion ratio can be calculated. This known ratio is then used along
with the CS5378 digital filter GAIN register to
normalize the full-scale amplitude to match
other channels in the measurement network.
By switching between DC common mode
(MODE 4) and DC differential mode
(MODE 5), pulse waveforms can be created to
characterize the step response of the measurement channel. If a pulse test requires precise timing control, an external controller
should directly toggle the MODE pins of the
CS5373A to avoid delays associated with writing to the CS5378 digital filter GPIO register.
Sensor impedance can be measured using
DC differential mode (MODE 5), provided
matched series resistors are installed between
the BUF analog outputs and the sensor. Applying the known DC differential voltage to the
resistor-sensor-resistor string permits a ratiometric sensor impedance calculation from the
measured voltage drop across the sensor.
Switching between DC differential mode
(MODE 5) and modulator mode (MODE 0) can,
in the case of a moving-coil geophone, test basic
parameters of the electro-mechanical transfer
function. The voltage relaxation characteristic of
the sensor when switching the analog outputs
from a differential DC voltage to high impedance
depends primarily on the geophone resonant
frequency and damping factor.
5.4 Sleep Mode
Sleep mode (MODE 7) saves system power
when measurements are not required by turning
off the modulator, AC test circuitry, and DC test
circuitry. In sleep mode the modulator digital outputs and the BUF and OUT analog outputs are
high impedance.
25
CS5373A
VA+
0.1µF
0. 1µF
VA +
Route BUF as diff pair
SENSOR
TEST OUTPUT
ELECTRONICS
TEST OUTPUT
VA+
2.5 V
VREF
+
Route OUT as diff pair
Route VREF as diff pair
VA680 Ω
INPUT FROM
CS 3301 A/02 A
AM PLIFIER
680 Ω
680 Ω
GPIO
GPIO
M ODE2
OUT+
ATT 0
OUTATT 1
CS5373A ATT 2
VREF +
VREF TDATA
GPIO
GPIO
GPIO
GPIO
*Populate with 2 x 10 nF or
1 x 22 nF C0 G or better .
20 nF
C0G
*
CS5378
SIGNALS
M ODE0
M ODE1
BUF+
BUF-
10 Ω
100 µF
VD
CAP +
CAP -
10 nF
C0 G
20 nF
C0 G
*
VD
M CLK
INR+
INF+
INF-
TBSDATA
M CLK
M SYNC
M SYNC
M DATA
M FLAG
M DATA
M FLAG
INR-
680 Ω
VA VA-
GND
0.1 µF
Figure 13. Digital Signals
6. DIGITAL SIGNALS
The CS5373A is designed to operate with the
CS5378 digital filter. The digital filter generates the master clock and synchronization signals (MCLK and MSYNC) while receiving back
the modulator one-bit ΔΣ conversion data
(MDATA) and over-range flag (MFLAG). It
also generates digital one-bit ΔΣ test bit
stream data for the test DAC (TDATA) and
controls GPIO pins to set the operational
mode (MODE) and attenuation (ATT).
6.1 MCLK Connection
The CS5378 digital filter generates the master
clock for CS5373A, typically 2.048 MHz, from
a synchronous CLK input from the external
system. By default, MCLK is disabled at reset
and is enabled by writing the digital filter CONFIG register. If MCLK is disabled during operation, the CS5373A will enter power down
after approximately 40 µS.
MCLK must have low in-band jitter to guarantee full analog performance, requiring a crystal- or VCXO-based system clock into the
digital filter. Clock jitter on the digital filter external CLK input directly translates to jitter on
MCLK.
26
6.2 MSYNC Connection
The CS5378 digital filter also provides a synchronization signal to the CS5373A. The
MSYNC signal is generated following a rising
edge received on the digital filter SYNC input.
By default MSYNC generation is disabled at
reset and is enabled by writing to the digital filter CONFIG register.
The input SYNC signal to the CS5378 digital
filter sets a common reference time t0 for measurement events, thereby synchronizing analog sampling across a measurement network.
The timing accuracy of the received SYNC signal from node to node must be +/- 1 MCLK to
maximize the MSYNC analog sample synchronization accuracy.
The CS5373A MSYNC input is rising-edge
triggered and resets the internal MCLK counter/divider to guarantee synchronous operation with other system devices. While the
MSYNC signal synchronizes the internal operation of the CS5373A, by default, it does not
synchronize the phase of the incoming encoded digital test bit stream (TBS) sine wave unless enabled in the digital filter TBSCFG
register.
DS703F2
CS5373A
6.3 MDATA Connection
The CS5373A modulator outputs a ΔΣ serial
bit stream to the MDATA pin, with a one’s density proportional to the differential amplitude of
the analog input signal. The output bit rate
from the MDATA output is a divide-by-four of
the input master clock, and so is nominally
512 kHz.
The MDATA output has a nominal 50% one’s
density for mid-scale input, approximately
86% one’s density for a positive full-scale input, and approximately 14% one’s density for
a negative full-scale input. One’s density of the
MDATA output is defined as the ratio of ‘1’ bits
to total bits in the serial bit stream output, i.e.
an 86% one’s density has, on average, a ‘1’
value in 86 of every 100 output data bits.
6.4 MFLAG Connection
The CS5373A ΔΣ modulator has a 4th order architecture which is conditionally stable and
may go into an oscillatory condition if the analog inputs are over-ranged more than 5% past
either positive or negative full-scale.
If an unstable condition is detected, the modulator collapses to a 1st order system and transitions the MFLAG output low-to-high to signal
an error condition to the CS5378 digital filter.
The analog signal must be reduced to within
the full-scale input range for at least 32 MCLK
cycles for the modulator to recover from an oscillatory condition. If the analog input remains
over-ranged for an extended period, the modulator will cycle between 4th order and 1st order operation and the MFLAG output will be
seen to pulse.
The MFLAG output connects to a dedicated input on the CS5378 digital filter, causing an error flag to be set in the status portion of the
next conversion output data word.
6.5 TDATA Connection
The TDATA digital input to the test DAC expects encoded one-bit ΔΣ data nominally at a
256 kHz rate. The one’s density input range is
DS703F2
approximately 25% minimum to 75% maximum, with differential mid-scale at 50% one’s
density.
The CS5378 digital filter test bit stream (TBS)
generator can encode two types of AC signals
as over-sampled, one-bit ΔΣ data – a pure sine
wave for THD and CMRR testing or a triggerable impulse waveform for synchronization
testing and impulse response characterization. In the AC test modes, the test DAC converts the over-sampled test bit stream digital
data into precision differential or common
mode analog AC signals.
The CS5378 TBS sine mode encodes an approximately 5 Vpp full-scale sine wave signal
with a digital filter TBSGAIN register setting of
0x04B8F2. Because TBS impulse mode encodes frequencies above 100 Hz, a maximum
0x0078E5 TBSGAIN impulse mode register
setting is specified to guarantee stability of the
DAC low-power ΔΣ circuitry. Details on the setup and operation of the digital filter test bitstream (TBS) generator can be found in the
CS5378 data sheet.
6.6 GPIO Connections
The CS5378 controls 8 general-purpose input
output (GPIO) pins through the digital filter
GPCFG register. These GPIO pins are typically assigned to operate the CS5373A mode and
attenuator pins, along with the CS3301A/02A
amplifier input mux and gain pins. The gain
and attenuation settings of the CS3301A/02A
amplifiers and the CS5373A test DAC are
identically decoded to allow full-scale performance testing at all system gain ranges with
shared GAIN and ATT control signals.
If precise timing control of operational modes
is required (for example, switching between
DC modes for pulse generation), an external
controller should directly toggle the MODE
pins of the CS5373A to avoid the delay associated with writing to the CS5378 digital filter
GPCFG register.
27
CS5373A
VA+
0.1µF
0. 1µF
VA +
CAP +
10 nF
C0 G
VA+
2.5 V
VREF
Route BUF as diff pair
ELECTRONICS
TEST OUTPUT
10 Ω
Route OUT as diff pair
+
100 µF
INPUT FROM
CS 3301 A/02 A
AM PLIFIER
680 Ω
680 Ω
CS5378
SIGNALS
BUF+
BUFOUT+
OUT-
Route VREF as diff pair
CS5373A
VREF +
VREF -
VA680 Ω
VD
CAP -
SENSOR
TEST OUTPUT
*Populate with 2 x 10 nF or
1 x 22 nF C0 G or better .
20 nF *
C0G
20 nF *
C0 G
680 Ω
INR+
INF+
INFINRVA -
VA-
VD
M ODE0
M ODE1
M ODE2
ATT 0
GPIO
GPIO
GPIO
GPIO
ATT 1
ATT 2
GPIO
GPIO
TDATA
TBSDATA
M CLK
M SYNC
M CLK
M SYNC
M DATA
M DATA
M FLAG
M FLAG
GND
0.1 µF
Figure 14. Analog Signals
7. ANALOG SIGNALS
The CS5373A has multiple differential analog
inputs and outputs. The modulator analog inputs are separated into rough and fine charge
differential pairs (INR±, INF±) for maximum
sampling accuracy. Both sets of modulator inputs require a simple differential anti-alias RC
filter to ensure high-frequency signals do not
alias into the measurement bandwidth.
The test DAC has a precision differential output (OUT±) that provides the best analog performance, but with only minimal drive
capability. A buffered output (BUF±) can drive
an external load, but with reduced analog performance. Finally, the test DAC internal antialias filter requires a dedicated capacitor connection (CAP±) to eliminate undesired highfrequency signals.
7.1 INR±, INF± Modulator Inputs
The modulator analog inputs are separated
into differential rough and fine signals (INR±,
INF±). The positive half of the differential input
signal is connected to INR+ and INF+, while
the negative half is attached to INF- and INR-.
The INR± pins are switched-capacitor ‘rough
charge’ inputs that pre-charge the internal analog sampling capacitor before it is connected
to the INF± fine input pins.
28
7.1.1
Modulator Input Impedance
The modulator input has a dynamic switchedcapacitor architecture and so has a rough
charge input impedance that is inversely proportional to the input master clock frequency
and the input capacitor size, [1 / (f * C)].
•
MCLK = 2.048 MHz
•
INR± Input Cap = 20 pF
•
Impedance = [1 / (2.048 MHz * 20 pF)] = 24 kΩ.
Internal to the modulator, the rough inputs
(INR±) pre-charge the sampling capacitor
used by the fine inputs (INF±), therefore the input current to the fine inputs is very low and the
effective input impedance is orders of magnitude above the impedance of the rough inputs.
7.1.2
Modulator Anti-alias Filter
The modulator inputs are required to be bandwidth limited to ensure modulator loop stability
and prevent high-frequency signals from aliasing into the measurement band. The use of
simple single-pole differential low-pass RC filters across the INR± and INF± inputs ensures
high-frequency signals are rejected before
they can alias into the measurement band.
DS703F2
CS5373A
The -3 dB corner of the input anti-alias filter is
nominally set to the internal analog sampling
rate divided by 64, which itself is a division by
4 of the MCLK input rate.
Selection ATT[2:0]
Attenuation
dB
0
000
1/1
0 dB
1
001
1/2
-6.02 dB
•
MCLK Frequency = 2.048 MHz
2
010
1/4
-12.04 dB
•
Sampling Frequency = MCLK / 4 = 512 kHz
3
0 11
1/8
-18.06 dB
•
-3 dB Filter Corner = Sample Freq / 64 = 8 kHz
4
100
1/16
-24.08 dB
•
RC filter = 8 kHz = 1 / [ 2π * (2 * Rseries) * Cdiff)]
5
101
1/32
-30.10 dB
6
11 0
1/64
-36.12 dB
7
111
reserved
reserved
Figure 14 illustrates the CS5373A modulator
analog connections with input anti-alias filter
components. Filter components on the rough
and fine pins should be identical values for optimum performance, with the capacitor values
a minimum of 0.02 μF. The rough input can
use either X7R or C0G type capacitors, while
the fine input requires C0G type capacitors for
optimal linearity. Using X7R type capacitors on
the fine analog inputs will degrade total harmonic distortion significantly.
The CS3301A/02A differential amplifiers are
designed with separate rough and fine analog
outputs (OUTR±, OUTF±) that match the
rough and fine inputs to the modulator (INR±,
INF±). Internal anti-alias series resistors are
NOT included in the amplifier analog outputs,
therefore external differential capacitors as
well as 680 Ω resistors are required to create
the anti-alias RC filters.
7.2 DAC Output Attenuation
The CS5373A test DAC has seven analog output attenuation settings from 1/1 to 1/64 selected with the ATT2, ATT1, and ATT0 pins.
When enabled, attenuation is applied to both
the OUT± and BUF± differential analog outputs. At 1/64 attenuation in AC Common Mode
(MODE 6) there is no output signal amplitude
due to the attenuator architecture.
The OUT± pins connect directly into the internal attenuator resistors and so attenuation accuracy is highly sensitive to load impedance
DS703F2
Figure 15. DAC Output Attenuation Settings
on the OUT± pins. Loading on the BUF± pins
does not affect attenuator accuracy.
The attenuation settings of CS5373A match
the gain ranges of the CS3301A/02A differential amplifiers to enable full-scale testing at all
gain ranges. The CS3301A/02A amplifier gain
settings (GAIN) are decoded identical to the
CS5373A attenuator settings (ATT) and so
can share GPIO control signals from the
CS5378 digital filter.
7.3 DAC OUT± Precision Output
The test DAC OUT± pins are precision differential analog outputs for testing the high-performance electronics measurement channel.
These precision outputs have higher performance specifications than the BUF± outputs,
but with a much higher sensitivity to external
loading. Excessive resistive or capacitive loading on the OUT± pins will degrade the analog
performance characteristics of the test DAC in
all operational modes.
The OUT± precision output is optimized for direct connection to the CS3301A/02A amplifier
differential inputs, which have very high input
impedance. These amplifiers include a pincontrolled input multiplexer to switch between
an internal differential termination for noise
29
CS5373A
tests and two external differential inputs. One
external input is typically dedicated to sensor
measurements and the other to testing the
electronics channel.
The OUT± outputs are enabled in all operational modes except modulator mode
(MODE 0), “AC BUF Only” mode (MODE 3)
and sleep mode (MODE 7). In modulator
mode, AC BUF Only mode and sleep mode
the OUT± pins are high impedance.
7.4 DAC BUF± Buffered Output
The test DAC BUF± pins are buffered differential analog outputs for testing external sensors
such as geophones or hydrophones. The buffered outputs have reduced performance specifications compared with the OUT± outputs,
but are less sensitive to external loading.
The BUF± outputs are enabled in all operational modes except modulator mode (MODE 0),
“AC OUT Only” mode (MODE 2) and sleep
mode (MODE 7). In modulator mode,
AC OUT only and sleep mode the BUF± pins
are high impedance to ensure they do not interfere with sensor operation during normal
data acquisition.
For sensor impedance testing, it is required to
place matched series resistors in between the
BUF± outputs and the differential sensor. With
known series resistors and a known DC differential source voltage, sensor resistance can
be calculated ratiometrically from the measured voltage drop across the sensor.
7.5 DAC CAP± Connection
The CS5373A test DAC requires a 10 nF C0G
type capacitor to be connected differentially
across the CAP± pins. This capacitor creates
an internal anti-alias filter to eliminate high-fre-
30
quency signals from the OUT± and BUF± analog outputs and helps to maintain the stability
of the low-power ΔΣ DAC circuitry.
A COG, NPO or similar high-quality capacitor
is required for CAP± since other capacitor
types, such as X7R, do not have the required
linearity. Using a poor-quality capacitor on
CAP± will significantly degrade THD performance of the test DAC AC operational modes.
7.6 Analog Differential Signals
Differential AC test signals into and out of the
CS5373A consist of two halves with equal but
opposite magnitude varying about a common
mode voltage. A full-scale 5 VPP differential
AC signal centered on a -0.15 V common
mode voltage will have:
SIG+ = -0.15 V + 1.25 V = +1.1 V
SIG- = -0.15 V - 1.25 V = -1.4 V
SIG+ is +2.5 V relative to SIGFor the opposite case:
SIG+ = -0.15 V - 1.25 V = -1.4 V
SIG- = -0.15 V + 1.25 V = +1.1 V
SIG+ is -2.5 V relative to SIGSo the total swing for SIG+ relative to SIG- is
(+2.5 V) - (-2.5 V) = 5 Vpp differential. A similar
calculation can be done for SIG- relative to
SIG+. It’s important to note that a 5 Vpp differential signal centered on a -0.15 V common
mode voltage never exceeds +1.1 V with respect to ground and never drops below -1.4 V
with respect to ground on either half. By definition, differential voltages are measured with
respect to the opposite half, not relative to
ground. A voltmeter differentially measuring
between SIG+ and SIG- in the above example
would correctly read 1.767 Vrms, or 5 Vpp.
DS703F2
CS5373A
From VA+
Regulator
100 μF
0.1 μF
10 Ω
2.500 V
VREF
From VARegulator
100 μF
0.1 μF
Route VREF± as a differential pair
from the 100uF RC filter capacitor
+ 100 μF
0.1 μF
0.1 μF
0.1 μF
To VREF+
To VREF-
Figure 16. Voltage Reference Circuit
8. VOLTAGE REFERENCE
The CS5373A requires a 2.500 V precision
voltage reference to be supplied to the VREF±
pins.
8.1 VREF Power Supply
To guarantee proper regulation headroom for
the voltage reference device, the voltage reference GND pin should be connected to VA- instead of system ground, as shown in
Figure 16. This connection results in a VREFvoltage equal to VA- and a VREF+ voltage
very near ground [(VA-) + 2.500 VREF].
Power supply inputs to the voltage reference
device should be bypassed to system ground
with 0.1 μF capacitors placed as close as possible to the power and ground pins. In addition
to 0.1 μF local bypass capacitors, at least
100 μF of bulk capacitance to system ground
should be placed on each power supply near
the voltage regulator outputs. Bypass capacitors should be X7R, C0G, tantalum, or other
high-quality dielectric type.
8.2 VREF RC Filter
A primary concern in selecting a precision voltage reference device is noise performance in
the measurement bandwidth. The Linear
Technology LT1019AIS8-2.5 voltage reference yields acceptable noise levels if the output is filtered with a low-pass RC filter.
A separate RC filter is required for each system device connected to a given voltage referDS703F2
ence. By sharing a common RC filter, signaldependent sampling of the voltage reference
by one system device could cause unwanted
tones to appear in the measurement bandwidth of another system device via common
impedance coupling.
8.3 VREF PCB Routing
To minimize the possibility of outside noise
coupling into the CS5373A voltage reference
input, the VREF± traces should be routed as a
differential pair from the large capacitor of the
voltage reference RC filter. Careful control of
the voltage reference source and return currents by routing VREF± as a differential pair
will improve immunity from external noise.
To further improve noise rejection of the
VREF± routing, include 0.1 μF bypass capacitors to system ground as close as possible
to the VREF+ and VREF- pins of the
CS5373A.
8.4 VREF Input Impedance
The switched-capacitor input architecture of
the VREF± inputs results in an input impedance that depends on the internal capacitor
size and the clock frequency. With a 15 pF internal capacitor and a 2.048 MHz MCLK the
VREF input impedance is approximately
[1 / [(2.048 MHz) * (15 pF)]] = 32 kΩ.
While
the size of the internal capacitor is fixed, the
voltage reference input impedance will vary
31
CS5373A
with MCLK.
The voltage reference external RC filter series
resistor creates a voltage divider with the
VREF input impedance to reduce the effective
applied input voltage. To minimize gain error
resulting from this voltage divider effect, the
RC filter series resistor should be the minimum
size recommended in the voltage reference
device data sheet.
8.5 VREF Accuracy
The nominal voltage reference input is specified as 2.500 V across the VREF± pins, and all
CS5373A gain accuracy specifications are
measured with a nominal voltage reference input. Any variation from a nominal VREF input
will proportionally vary the analog full-scale
gain accuracy.
Since temperature drift of the voltage reference results in gain drift of the analog full-scale
amplitude, care should be taken to minimize
temperature drift effects through careful selection of passive components and the voltage
reference device itself. Gain drift specifications
of the CS5373A do not include the tempera-
32
ture drift effects of external passive components or of the voltage reference device itself.
8.6 VREF Independence
If the test signal source is required to be fully
independent of the measurement channel, the
CS5373A device cannot be used. Instead, a
CS5371 modulator and a CS4373A test DAC
should be used and connected to two independent voltage reference devices. This will eliminate the possibility for undetected ratiometric
errors when the same voltage reference device is used by both the test signal source and
the measurement channel.
Because modern precision voltage references
are highly reliable, requirements for separate
modulator and test DAC voltage references
should be considered carefully. In the unlikely
event of voltage reference failure independent
of other system components, the CS5373A
volts-to-codes ratio will be out of spec and
measurement channel performance will be
poor during system self-tests.
DS703F2
CS5373A
To VA+
Regulator
To VD
Regulator
100 uF
0.1 uF
0.1 uF
VA+
100 uF
VD
CS5373A
VA-
GND
To VARegulator
100 uF
0.1 uF
Figure 17. Power Supply Diagram
9. POWER SUPPLIES
The CS5373A has a positive analog power
supply pin (VA+), a negative analog power
supply pin (VA-), a digital power supply pin
(VD), and a ground pin (GND).
For proper operation, power must be supplied
to all power supply pins, and the ground pin
must be connected to system ground. The
CS5373A digital power supply (VD) and the
CS5378 digital power supply (VDDPAD) must
share a common power supply voltage.
9.1 Power Supply Bypassing
The VA+, VA-, and VD power supplies should
be bypassed to system ground with 0.1 μF capacitors placed as close as possible to the
power pins of the device. In addition to the
0.1 μF local bypass capacitors, at least 100 μF
bulk capacitance to system ground should be
placed on each power supply near the voltage
regulator output, with additional power supply
bulk capacitance placed among the analog
component route if space permits. Bypass capacitors should be X7R, C0G, tantalum, or
other high-quality dielectric type.
9.2 PCB Layers and Routing
The CS5373A is a high-performance device,
and special care must be taken to ensure power and ground routing is correct. Power can be
supplied either through dedicated power
planes or routed traces. When routing power
traces, it is recommended to use a “star” routDS703F2
ing scheme with the star point either at the
voltage regulator output or at a local power
supply bulk capacitor.
It is also recommended to dedicate a full PCB
layer to a solid ground plane, without splits or
routing. All bypass capacitors should connect
between the power supply circuit and the solid
ground plane as near as possible to the device
power supply pins.
The CS5373A analog signals are differentially
routed and do not normally require connection
to a separate analog ground. However, if a
separate analog ground is required, it should
be routed using a “star” routing scheme on a
separate layer from the solid ground plane and
connected to the ground plane only at the star
point. Be sure all active devices and passive
components connected to the analog ground
are included in the “star” route to ensure sensitive analog currents do not return through the
ground plane.
9.3 Power Supply Rejection
Power supply rejection of the CS5373A is frequency dependent. The CS5378 digital filter
rejects power supply noise for frequencies
above the selected digital filter corner frequency. Power supply noise frequencies between
DC and the digital filter corner frequency are
rejected
as
specified
in
the
Power Supply Characteristics table.
33
CS5373A
9.4 SCR Latch-up
The VA- pin is tied to the CS5373A CMOS
substrate and must always be the most-negative voltage applied to the device to ensure
SCR latch-up does not occur. In general,
latch-up may occur when any pin voltage exceeds
the
limits
specified
in
the
Absolute Maximum Ratings table.
It is recommended to connect the VA- power
supply to system ground (GND) with a reverse-biased Schottky diode. At power up, if
the VA+ power supply ramps before the VAsupply is established, the VA- pin voltage
could be pulled above ground potential
through the CS5373A device. If the VA- supply
is pulled 0.7 V or more above GND, SCR
latch-up can occur. A reverse-biased Schottky
diode will clamp the VA- voltage a maximum of
0.3 V above ground to ensure SCR latch-up
does not occur at power up.
9.5 DC-DC Converters
Many low-frequency measurement systems
are battery powered and utilize DC-DC con-
verters to efficiently generate power supply
voltages. To minimize interference effects, operate the DC-DC converter at a frequency
which is rejected by the digital filter, or operate
it synchronous to the MCLK rate.
A synchronous DC-DC converter whose operating frequency is derived from MCLK will theoretically minimize the potential for “beat
frequencies” to appear in the measurement
bandwidth. However this requires the source
clock to remain jitter-free within the DC-DC
converter circuitry. If clock jitter can occur within the DC-DC converter (as in a PLL-based architecture), it’s better to use a nonsynchronous DC-DC converter whose switching frequency is rejected by the digital filter.
During PCB layout, do not place high-current
DC-DC converters near sensitive analog components. Carefully routing a separate DC-DC
“star” ground will help isolate noisy switching
currents away from the sensitive analog components.
10.TERMINOLOGY
Signal-to-Noise Ratio (Dynamic Range) - Ratio of the rms magnitude of the full-scale signal to the integrated
rms noise from DC to 400 Hz. The following formula is used to calculate SNR:
SNR = 20log
Total Harmonic Distortion - Ratio of the power of the fundamental frequency to the sum of the powers of all
harmonic frequencies from DC to 400 Hz. The following formula is used to calculate THD:
THD = 10log
the powers of the harmonic frequencies
( sum ofpower
of the fundamental frequency
(
•
of full scale signal
( rmsrmsmagnitude
magnitude of noise floor
(
•
•
Full-scale Bandwidth - The bandwidth in which the converter can generate a full-scale signal while maintaining
performance specifications.
•
Impulse Amplitude - The maximum amplitude of the output signal beyond the full-scale bandwidth.
•
Differential Output Level - The voltage between the analog output pins of the device.
34
DS703F2
CS5373A
Full-scale Accuracy - Variation in the measured output voltage from the theoretical full-scale output voltage at
1x attenuation. The following formula is used to calculate full-scale accuracy:
voltage - theoretical full scale voltage
( measured full scale
theoretical full scale voltage
|
•100%
Relative Accuracy - Variation in the measured output voltage from the theoretical attenuated output voltage at
each of the attenuation ranges. The following formula is used to calculate relative accuracy:
(
(
|
measured attenuated voltage - theoretical attenuated voltage
relative accuracy = theoretical attenuated voltage (relative to the measured full scale voltage) •100%
|
•
(
full scale accuracy =
|
•
•
Full Scale Drift - The variation of the measured full-scale voltage across the specified temperature range.
•
Common Mode Drift - The variation in the measured common mode voltage across the specified temperature
range.
DS703F2
35
CS5373A
11. PIN DESCRIPTION
Positive Capacitor Output
CAP+
1
28
GND
System Ground
Negative Capacitor Output
CAP-
2
27
MODE0
Mode Select
Positive Buffered Output
BUF+
3
26
MODE1
Mode Select
Negative Buffered Output
BUF-
4
25
MODE2
Mode Select
Positive High Precision Output
OUT+
5
24
ATT0
Attenuation Range Select
Negative High Precision Output
OUT-
6
23
ATT1
Attenuation Range Select
Positive Analog Power Supply
VA+
7
22
ATT2
Attenuation Range Select
Negative Analog Power Supply
VA-
8
21
TDATA
Test Bit Stream Input
Negative Voltage Reference
VREF-
9
20
VD
Positive Digital Power Supply
Positive Voltage Reference
VREF+
10
19
GND
System Ground
Positive Analog Rough Input
INR+
11
18
MCLK
Master Clock Input
Positive Analog Fine Input
INF+
12
17
MSYNC
Master Sync Input
Negative Analog Fine Input
INF-
13
16
MDATA
Modulator Data Output
Negative Analog Rough Input
INR-
14
15
MFLAG
Modulator Over-range Indicator
Pin
Name
Pin # I/O
Pin Description
CAP+,
CAP-
1
2
O Capacitor connection for internal anti-alias filter.
BUF+,
BUF-
3
4
O Buffered differential analog output.
OUT+,
OUT-
5
6
O Precision differential analog output.
VA+,
VA-
7
8
VREF-,
VREF+
9
10
I
Voltage reference input. Refer to the Specified Operating Conditions.
INR+,
INF+
11
12
I
Analog differential rough and fine + inputs. From the + half of the differential anti-alias filter.
INF-,
INR-,
13
14
I
Analog differential rough and fine - inputs. From the - half of the differential anti-alias filter.
MFLAG
15
O Amplitude overload indicator flag.
MDATA
16
O Oversampled ΔΣ bit stream conversion output.
MSYNC
17
I
Master sync input. Low to high transition resets the internal clock phasing.
MCLK
18
I
Master clock input. CMOS compatible clock input.
GND
19
VD
20
TDATA
21
36
Analog power supply. Refer to the Specified Operating Conditions.
System ground.
Digital power supply. Refer to the Specified Operating Conditions.
I
Test Bit Stream input from digital filter TBS generator.
DS703F2
CS5373A
Pin
Name
ATT2,
ATT1,
ATT0
MODE2,
MODE1,
MODE0
Pin # I/O
Pin Description
22,
23,
24
25,
26,
27
I
Attenuation Range. Selects the output attenuation range.
Attenuation
I
Selection
ATT[2:0]
Attenuation
dB
0
000
1/1
0 dB
1
001
1/2
-6.02 dB
2
010
1/4
-12.04 dB
3
0 11
1/8
-18.06 dB
4
100
1/16
-24.08 dB
5
101
1/32
-30.10 dB
6
11 0
1/64
-36.12 dB
7
111
reserved
reserved
Mode Selection. Determines the operational mode of the device.
Modes of Operation
Selection MODE[2:0]
GND
DS703F2
28
Mode Description
0
000
Modulator: enabled.
DAC: sleep.
1
001
Modulator: enabled.
DAC: AC OUT and BUF outputs.
2
010
Modulator: enabled.
DAC: AC OUT only, BUF high-z.
3
0 11
Modulator: enabled.
DAC: AC BUF only, OUT high-z.
4
100
Modulator: enabled.
DAC: DC common mode output.
5
101
Modulator: enabled.
DAC: DC differential output.
6
11 0
Modulator: enabled.
DAC: AC common mode output.
7
111
Modulator: sleep.
DAC: sleep.
System ground.
37
CS5373A
12. PACKAGE DIMENSIONS
28L SSOP PACKAGE DRAWING
N
D
E11
A2
E
e
b2
SIDE VIEW
A
∝
A1
L
END VIEW
SEATING
PLANE
1 2 3
TOP VIEW
DIM
A
A1
A2
b
D
E
E1
e
L
∝
MIN
-0.002
0.064
0.009
0.390
0.291
0.197
0.022
0.025
0°
INCHES
NOM
-0.006
0.069
-0.4015
0.307
0.209
0.026
0.0354
4°
MAX
0.084
0.010
0.074
0.015
0.413
0.323
0.220
0.030
0.041
8°
MIN
-0.05
1.62
0.22
9.90
7.40
5.00
0.55
0.63
0°
MILLIMETERS
NOM
-0.15
1.75
-10.20
7.80
5.30
0.65
0.90
4°
NOTE
MAX
2.13
0.25
1.88
0.38
10.50
8.20
5.60
0.75
1.03
8°
2,3
1
1
JEDEC #: MO-150
Controlling Dimension is Millimeters
Notes: 1. “D” and “E1” are reference datums and do not included mold flash or protrusions, but do include mold
mismatch and are measured at the parting line, mold flash or protrusions shall not exceed 0.20 mm per
side.
2. Dimension “b” does not include dambar protrusion/intrusion. Allowable dambar protrusion shall be
0.13 mm total in excess of “b” dimension at maximum material condition. Dambar intrusion shall not
reduce dimension “b” by more than 0.07 mm at least material condition.
3. These dimensions apply to the flat section of the lead between 0.10 and 0.25 mm from lead tips.
38
DS703F2
CS5373A
13.ORDERING INFORMATION
Model
Temperature
CS5373A-ISZ (lead free)
Package
-40 to +85 °C
28-pin SSOP
14.ENVIRONMENTAL, MANUFACTURING, & HANDLING INFORMATION
Model Number
CS5373A-ISZ (lead free)
Peak Reflow Temp
MSL Rating*
Max Floor Life
260 °C
3
7 Days
* MSL (Moisture Sensitivity Level) as specified by IPC/JEDEC J-STD-020.
15.REVISION HISTORY
Revision
Date
PP1
NOV 2005
Preliminary release for CS5373A.
PP2
NOV 2005
Correct voltage units of full-scale DC differential output and common mode AC
output at 1/4 attenuation. Add Ttdata timing to Figure 5. Correct bypass capacitor
sizes in Figure 8. Correct definition of pin 28 in Pin Description table.
F1
OCT 2010
Removed reference to CS3301/02, replaced with CS3301A/02A.
Removed device ordering info for devices containing lead (Pb).
DS703F2
Changes
39
CS5373A
Contacting Cirrus Logic Support
For all product questions and inquiries contact a Cirrus Logic Sales Representative.
To find the one nearest to you go to www.cirrus.com
IMPORTANT NOTICE
Cirrus Logic, Inc. and its subsidiaries ("Cirrus") believe that the information contained in this document is accurate and reliable. However, the information is subject
to change without notice and is provided "AS IS" without warranty of any kind (express or implied). Customers are advised to obtain the latest version of relevant
information to verify, before placing orders, that information being relied on is current and complete. All products are sold subject to the terms and conditions of sale
supplied at the time of order acknowledgment, including those pertaining to warranty, indemnification, and limitation of liability. No responsibility is assumed by Cirrus
for the use of this information, including use of this information as the basis for manufacture or sale of any items, or for infringement of patents or other rights of third
parties. This document is the property of Cirrus and by furnishing this information, Cirrus grants no license, express or implied under any patents, mask work rights,
copyrights, trademarks, trade secrets or other intellectual property rights. Cirrus owns the copyrights associated with the information contained herein and gives consent for copies to be made of the information only for use within your organization with respect to Cirrus integrated circuits or other products of Cirrus. This consent
does not extend to other copying such as copying for general distribution, advertising or promotional purposes, or for creating any work for resale.
CERTAIN APPLICATIONS USING SEMICONDUCTOR PRODUCTS MAY INVOLVE POTENTIAL RISKS OF DEATH, PERSONAL INJURY, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE ("CRITICAL APPLICATIONS"). CIRRUS PRODUCTS ARE NOT DESIGNED, AUTHORIZED OR WARRANTED FOR USE
IN PRODUCTS SURGICALLY IMPLANTED INTO THE BODY, AUTOMOTIVE SAFETY OR SECURITY DEVICES, LIFE SUPPORT PRODUCTS OR OTHER CRITICAL APPLICATIONS. INCLUSION OF CIRRUS PRODUCTS IN SUCH APPLICATIONS IS UNDERSTOOD TO BE FULLY AT THE CUSTOMER'S RISK AND CIRRUS DISCLAIMS AND MAKES NO WARRANTY, EXPRESS, STATUTORY OR IMPLIED, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND
FITNESS FOR PARTICULAR PURPOSE, WITH REGARD TO ANY CIRRUS PRODUCT THAT IS USED IN SUCH A MANNER. IF THE CUSTOMER OR CUSTOMER'S CUSTOMER USES OR PERMITS THE USE OF CIRRUS PRODUCTS IN CRITICAL APPLICATIONS, CUSTOMER AGREES, BY SUCH USE, TO FULLY INDEMNIFY CIRRUS, ITS OFFICERS, DIRECTORS, EMPLOYEES, DISTRIBUTORS AND OTHER AGENTS FROM ANY AND ALL LIABILITY, INCLUDING
ATTORNEYS' FEES AND COSTS, THAT MAY RESULT FROM OR ARISE IN CONNECTION WITH THESE USES.
Cirrus Logic, Cirrus, and the Cirrus Logic logo designs are trademarks of Cirrus Logic, Inc. All other brand and product names in this document may be trademarks
or service marks of their respective owners.
40
DS703F2