ROHM SH3002

Near edge type thermal printhead(11.81dots / mm)
SH3002-DC90A
SH-DC90 series achieves high quality print and high reliability, by Rohm unique Step Free Technology.
SH-DC90 series is near edge type thermal head, whose heater line is formed at the angle of the glaze. Therefore, peeling-off
ribbon at the hot state and large size platen can be used with this thermal head and is best suitable for the packaging printer
market which requires the continuous print at high speed.
zApplications
Barcode label printers
Packaging printers
Ticket printers
General purpose portable printers
zFeatures
1) ROHM unique “STEP FREE” structure contributes to better anti-corrosion characteristics, less scratch break down, and
better heat efficiency.
2) Thermal head contacts with the media by angle at the print, so that good print quality can be obtained for the thick media.
3) It has good anti-ESD characteristic by applying hard, conductive layer as the heat element protective coating.
4) Mounting space can be minimized, which contributes to the downsizing of the printer.
zDimensions (Unit : mm)
DOT No.640
(5.896)
66±0.5
54.208
Pape
r fe
directi ed
on
31.0±0.5
Max. 56
6±0.5
DOT No.1
Max. 5.5
3.0 (Typ.)
#2
#20
#4
Max. 12
#1
#1
#19 CONNECTOR B
CONNECTOR A
24.35±0.3
7.3±0.3
(13)
φ3H10
EFFECTIVE DEPTH 3
φ3H10 LENGTH 4
EFFECTIVE DEPTH 3
7.104±0.3
20±0.3
EFFECTIVE DEPTH 3
40±0.3
www.rohm.com
c 2009 ROHM Co., Ltd. All rights reserved.
○
1/3
2009.02 - Rev.A
Data Sheet
SH3002-DC90A
zEquivalent circuit
DOT#640
DOT#1
VH(COM)
#640
#321
#320
#1
VDD
0.1µF
50V
GND
BEO
/STB2
/STB1
LATCH REGISTER
/LAT
CLK
SHIFT
REGISTER
DI2
SHIFT
REGISTER
DI1
SENS1
SENS2
SENS3
THERMISTOR
30kΩ B:3950K
TM
TM
CONNECTOR
DI No.
DOT No.
STB No.
DOT No.
DI2
640 to 321
/STB 2
640 to 321
DI1
320 to 1
/STB 1
320 to 1
zPin configuration
HIROSE
No.
JST
Circuit
No.
Circuit
No.
Circuit
1
VDD
2
BEO
1
VH
3
GND
4
DI2
2
VH
5
N.C.
6
CLK
3
GND
7
LAT
8
N.C.
4
GND
9
N.C.
10
DI1
11
N.C.
12
GND
13
VDD
14
STB2
15
STB1
16
TM
17
TM
18
SENS1
19
SENS2
20
SENS3
www.rohm.com
c 2009 ROHM Co., Ltd. All rights reserved.
○
2/3
2009.02 - Rev.A
Data Sheet
SH3002-DC90A
zTiming chart
Min.45ns
CLK
Min.30ns Min.10ns
DI
(DATA IN)
BEO
Min.50ns
Min.100ns
Min.12.5µs
/LAT
(LATCH)
Min.100ns
Min.300ns
/STB
(STROBE)
Max.12.5µs
Max.12.5µs
DRIVER
OUT
zCharacteristics
Parameter
Symbol
Typical
Unit
mm
Effective printing width
−
54.208
Dot pitch
−
0.0847
mm
Total dot number
−
640
dots
Rave
850
Ω
VH
24
V
Average resistance value
Applied voltage
Applied power
PO
0.59
W / dot
SLT
0.28
ms
Maximum number of dots energized simultaneously
−
640
dots
Maximum clock frequency
−
10
MHz
Maximum roller diameter
−
φ50
Running life / pulse life
−
150 / 1x10
Operating temperature
−
5 to 45
Print cycle
www.rohm.com
c 2009 ROHM Co., Ltd. All rights reserved.
○
3/3
mm
8
km / pulses
°C
2009.02 - Rev.A
Appendix
Notes
No copying or reproduction of this document, in part or in whole, is permitted without the consent of ROHM
Co.,Ltd.
The content specified herein is subject to change for improvement without notice.
The content specified herein is for the purpose of introducing ROHM's products (hereinafter "Products"). If you
wish to use any such Product, please be sure to refer to the specifications, which can be obtained from ROHM
upon request.
Examples of application circuits, circuit constants and any other information contained herein illustrate the
standard usage and operations of the Products. The peripheral conditions must be taken into account
when designing circuits for mass production.
Great care was taken in ensuring the accuracy of the information specified in this document. However, should
you incur any damage arising from any inaccuracy or misprint of such information, ROHM shall bear no responsibility for such damage.
The technical information specified herein is intended only to show the typical functions of and examples
of application circuits for the Products. ROHM does not grant you, explicitly or implicitly, any license to
use or exercise intellectual property or other rights held by ROHM and other parties. ROHM shall bear no responsibility whatsoever for any dispute arising from the use of such technical information.
The Products specified in this document are intended to be used with general-use electronic equipment
or devices (such as audio visual equipment, office-automation equipment, communication devices, electronic appliances and amusement devices).
The Products are not designed to be radiation tolerant.
While ROHM always makes efforts to enhance the quality and reliability of its Products, a Product may fail or
malfunction for a variety of reasons.
Please be sure to implement in your equipment using the Products safety measures to guard against the
possibility of physical injury, fire or any other damage caused in the event of the failure of any Product, such as
derating, redundancy, fire control and fail-safe designs. ROHM shall bear no responsibility whatsoever for your
use of any Product outside of the prescribed scope or not in accordance with the instruction manual.
The Products are not designed or manufactured to be used with any equipment, device or system
which requires an extremely high level of reliability the failure or malfunction of which may result in a direct
threat to human life or create a risk of human injury (such as a medical instrument, transportation equipment,
aerospace machinery, nuclear-reactor controller, fuel-controller or other safety device). ROHM shall bear
no responsibility in any way for use of any of the Products for the above special purposes. If a Product is intended to be used for any such special purpose, please contact a ROHM sales representative before purchasing.
If you intend to export or ship overseas any Product or technology specified herein that may be controlled under
the Foreign Exchange and the Foreign Trade Law, you will be required to obtain a license or permit under the Law.
Thank you for your accessing to ROHM product informations.
More detail product informations and catalogs are available, please contact your nearest sales office.
ROHM Customer Support System
www.rohm.com
Copyright © 2009 ROHM Co.,Ltd.
THE AMERICAS / EUROPE / ASIA / JAPAN
Contact us : webmaster @ rohm.co. jp
21 Saiin Mizosaki-cho, Ukyo-ku, Kyoto 615-8585, Japan
TEL : +81-75-311-2121
FAX : +81-75-315-0172
Appendix-Rev4.1