UPD24 Series • SIP SSR • Single Channel Ratings of 15A and 25A @ 280 VAC • PCB Mount Package or Panel Mount quick connect terminals (F option) • SCR output for heavy industrial loads • Zero-crossing (resistive loads) or random-fire (inductive loads) output • Low Leakage (snubberless) output PRODUCT SELECTION Control Voltage 3-32 VDC 15A 15A 25A 25A UPD2415 UPD2415-10 UPD2425 UPD2425-10 UPD2415 UPD2415-10 UPD2425 UPD2425-10 24-280 15 600 115/120 1.4 1.2 66/60 0.1 500 0.5 24-280 15 600 115/120 1.4 1.2 66/60 0.1 500 0.5 24-280 25 600 239/250 1.4 0.7 285/259 0.1 500 0.5 24-280 25 600 239/250 1.4 0.7 285/259 0.1 500 0.5 UPD2415 UPD2415-10 UPD2425 UPD2425-10 3-32 VDC 3.0 VDC 1.0 VDC 10 mAdc See note 4 1/2 Cycle 1/2 Cycle 3-32 VDC 3.0 VDC 1.0 VDC 10 mAdc See note 4 0.02 1/2 Cycle 3-32 VDC 3.0 VDC 1.0 VDC 10 mAdc See note 4 1/2 Cycle 1/2 Cycle 3-32 VDC 3.0 VDC 1.0 VDC 10 mAdc See note 4 0.02 1/2 Cycle AVAILABLE OPTIONS OUTPUT SPECIFICATIONS (1) Description Operating Voltage (47-440Hz) [Vrms] Maximum Load Current [Arms](3) Transient Overvoltage [Vpk] Maximum 1 Cycle Surge Current (50/60Hz) [Apk] Maximum On-State Voltage Drop @ Rated Current [Vpk] Thermal Resistance Junction to Case [°C/W] Maximum I² t for fusing (50/60Hz, 1/2 cycle) [A² sec] Maximum Off-State Leakage Current @ Rated Voltage [mArms] Minimum Off-State dv/dt @ Maximum Rated Voltage [V/µsec] (2) Minimum Power Factor (with Maximum Load) INPUT SPECIFICATIONS (1) Description Control Voltage Range Must Turn On Voltage Must Turn Off Voltage Typical Input Current @ 12 VDC Nominal Input Impedance Maximum Turn-On Time [msec] Maximum Turn-Off Time [msec] GENERAL SPECIFICATIONS Description Parameters Dielectric Strength, Input/Output/Base (50/60Hz) Minimum Insulation Resistance (@ 500 VDC) 2500 Vrms 109 Ohm Maximum Capacitance, Input/Output Ambient Operating Temperature Range Ambient Storage Temperature Range Weight (typical) 10 pF -40 to 80°C -40 to 125°C 1.5 oz. (42.5g) GENERAL NOTES 1) All parameters at 25°C and per section unless otherwise specified. 2) Off-state dv/dt test method per EIA/NARM standard RS-443, paragraph 13.11.1 3) Heat sinking required, see following pages for derating curves. 4) Input circuit incorporates active current limiter. MECHANICAL SPECIFICATIONS UPD2415 UPD2425 3.08 3.08 2.80 2.80 0.15 0.15 ASSEMBLED IN MEXICO ASSEMBLED IN MEXICO 1.12 INPUT - + AC OUTPUT INPUT - AC AC + OUTPUT 1.12 AC 0.22 0.20 0.80 0.60 0.47 SQ 0.032 ±.005 (4 PLACES) 0.20 0.60 0.20 3.08 2.80 + AC 1.12 .200 X .032 SQ FASTON TERMINAL (2 PLACES) WIRING DIAGRAM 0.40 0.20 Note: Output terminals doubled for 25Amp models UPD24XXF 0.15 SQ 0.032 ±.005 (6 PLACES) 0.20 0.50 ASSEMBLED IN MEXICO AC .250 X .032 SQ FASTON TERMINAL (2 PLACES) 0.50 0.47 0.50 THERMAL DERATE INFORMATION THERMAL DERATE INFORMATION AGENCY APPROVALS Designed in accordance with the requirements of IEC 62314 Rev. 112614 ANNEX - ENVIROMENTAL INFORMATION