ROHM MNR15E0RPJ

MNR15
Resistors
Chip resistor networks
MNR15 (0603×5 size)
zFeatures
1) Suitable for pull-up and pull-down resistors.
2) No direction to be mounted by placing common electrode with symmetry.
3) Convex electrodes
Easy to check the fillet after soldering is finished.
4) High-density mounting
Can be mounted even densely than eight 0402chips (MCR01), and mounting costs are lower.
5) Compatible with a wide range of mounting machines.
Squared corners make it excellent for mounting using image recognition machines.
6) ROHM resistors have approved ISO-9001 certification.
Design and specifications are subject to change without notice. Carefully check the specification sheet supplied with
the product before using or ordering it.
zRatings
Item
Rated power
Conditions
Specifications
Power must be derated according to the power derating curve in
Figure 1 when ambient temperature exceeds 70°C.
0.031W (1 / 32W)
at 70°C
POWER LOAD (%)
100
80
60
40
20
0
−55
0
70
100
125
AMBIENT TEMPERATURE (°C)
Fig.1
Rated voltage
The voltage rating is calculated by the following equation. If the value
obtained exceeds the limiting element voltage, the voltage rating
is equal to the maximum operating voltage.
E : Rated voltage (V)
P : Rated power (W)
R : Nominal resistance (Ω)
E= P×R
Nominal resistance
Limiting element voltage
12.5V
See Table 1.
−55°C to +125°C
Operating temperature
Table 1
Resistance tolerance
J (±5%)
Resistance range
(Ω)
56≤R≤100k
(E24)
Resistance temperature coefficient
(ppm / °C)
±200
∗Before using components in circuits where they will be exposed to transients such as pulse loads(short-duration, high-level loads),
be certain to evaluate the component in the mounted state. In addition, the reliability and performance of this component cannot be
guaranteed if it is used with a steady state voltage that is greater than its rated voltage.
Rev.B
1/4
MNR15
Resistors
zCharacteristics
Guaranteed value
Resistor type
Item
Test conditions (JIS C 5201-1)
J : ±5%
Resistance
Variation of resistance
with temperature
JIS C 5201-1 4.5
JIS C 5201-1 4.8
Measurement : +25 / +125°C
See Table.1
JIS C 5201-1 4.13
Rated voltage×2.5, 2s.
Maximum Overload Voltage : 25V
± (2.0%+0.1Ω)
Overload
JIS C 5201-1 4.17
Rosin·Ethanol (25%WT)
Soldering condition : 235±5°C
Duration of immersion : 2.0±0.5s.
A new uniform coating of minimum of
95% of the surface being immersed
and no soldering damage.
Solderability
± (1.0%+0.05Ω)
Resistance to
soldering heat
No remarkable abnormality on the appearance.
Rapid change of
temperature
± (1.0%+0.05Ω)
JIS C 5201-1 4.19
Test temp. : −55°C to +125°C 5cyc
± (3.0%+0.1Ω)
JIS C 5201-1 4.24
40°C, 93%RH
Test time : 1,000h to 1,048h
± (3.0%+0.1Ω)
JIS C 5201-1 4.25.1
Rated voltage, 70°C
1.5h : ON − 0.5h : OFF
Test time : 1,000h to 1,048h
± (3.0%+0.1Ω)
JIS C 5201-1 4.25.3
125°C
Test time : 1,000h to 1,048h
± (1.0%+0.05Ω)
JIS C 5201-1 4.29
23±5°C, Immersion cleaning, 5±0.5min.
Solvent : 2-propanol
± (1.0%+0.05Ω)
JIS C 5201-1 4.33
Damp heat, steady state
Endurance at 70°C
Endurance
Resistance to solvent
Bend strength of
the end face plating
JIS C 5201-1 4.18
Soldering condition : 260±5°C
Duration of immersion : 10±1s.
Without mechanical damage such as breaks.
zExternal dimensions (Unit : mm)
3.2±0.1
a
b
b
a : 0.48±0.15
b : 0.32±0.15
B
No.
Material
0.35±0.1
A'
1.6±0.1
A
0.3±0.1
Thick dielectric glaze of oxide metal
Thick film of silver for electrode
Nickel-coated electrode
External electrode coated with Sn
∗
∗
∗
∗
Alumina substrate
∗0.64
Overcoating (Resin)
0.5±0.1
B'
Cross section A−A'
Cross sectionB−B'
∗Pitch of the upper electrode.
1
1
Maqnification
Rev.B
2/4
MNR15
Resistors
zEquivalent circuit
R5
R1
R2
R3
R6
R7
R8
R4
R1 = R2 = R3 = R4 = R5 = R6 = R7 = R8
zPackaging
Reel
Taping
P0
P2
φD0
P1
E
F
02
04
06
101
101
101
101
08
W
08
06
D
04
B
02
A
B0
A0
Heat crimp cover / Tape
Chip network
Thick paper (Underside paper tape) resistors
Square punchout hole
mount
T2
C
(Unit : mm)
Label
EIAJ ET-7200B compliant
(Unit: mm)
A
φ180
B
0
−1.5
φ60
C
+1
0
9
+1.0
0
W
F
E
A0
B0
8.0±0.3
3.5±0.05
1.75±0.1
1.8±0.1
3.4±0.1
D0
P0
P1
P2
T2
φ1.5 +0.1
0
4.0±0.1
4.0±0.1
2.0±0.05
Max. 1.1
D
φ13±0.2
zProduct designation
M N R 1 5
Part No.
E 0 R P
J
Resistance tolerance
Nominal resistance
J
±5%
J is also used
for jumper
Resistance code,3 digits,
000 denotes Jumper type.
Packaging Specifications Code
Part No.
Code
MNR15
E0RP
Resistance tolerance
J(±5%)
Packaging specifications
Paper tape (4mm Pitch)
Reel
Basic ordering unit (pcs)
φ180mm (7in.)
5,000
Reel (φ180) : JEITA ET-7200B
: Standard product
Rev.B
3/4
MNR15
Resistors
zElectrical characteristics
400
DC RESISTANCE (%)
4.0
3.0
2.0
1.0
0
−1.0
−2.0
−3.0
−4.0
−5.0
−6.0
56
100
1k
10k
100k
300
4.0
3.0
2.0
100
0
−100
1.0
0
−1.0
−2.0
−3.0
−200
−4.0
−300
−5.0
−400
56
100
1k
10k
100k
−6.0
56
3.0
JIS C 5201-1 4.18
SAMPLE SIZE : n=24pcs
SOLDERING CONDITION
: 260°C 10S
4.0
2.0
∆R/R (%)
∆R/R (%)
1.0
0
0
−1.0
−1.0
−2.0
−2.0
100k
JIS C 5201-1 4.24
SAMPLE SIZE : n = 24pcs
40°C 93%RH WITH NO LOAD
1000h
5.0
3.0
1.0
10k
6.0
JIS C 5201-1 4.19
SAMPLE SIZE : n=24pcs
−55°C / 125°C 5cyc
2.0
1k
Fig.4 Overload
Fig.3 Vatiation resistance with
temperature
3.0
100
RESISTANCE (Ω)
RESISTANCE (Ω)
Fig.2 Resistance
2.0
JIS C 5201-1 4.13
SAMPLE SIZE : n=24pcs
RATED VOLTAGE×2.5TIMES 2S
MAXIMUM OVERLOAD VOLTAGE : 25V
5.0
200
RESISTANCE (Ω)
∆R/R (%)
6.0
JIS C 5201-1 4.8
SAMPLE SIZE : n=24pcs
25°C / 125°C
∆R/R (%)
JIS C 5201-1 4.5
SAMPLE SIZE : n=24pcs
20°C 65%RH
5.0
TEMPERATURE COEFICIENT (ppm/°C)
6.0
1.0
0
−1.0
−2.0
−3.0
−4.0
−5.0
−3.0
56
100
1k
10k
100k
−3.0
56
Fig.5 Resistance to soldering heat
10k
100k
−6.0
56
100
1k
10k
100k
RESISTANCE (Ω)
Fig.6 Rapid change of temperature
6.0
Fig.7 Damp heat, steady state
6.0
JIS C 5201-1 4.25.1
SAMPLE SIZE : n=24pcs
70°C 1,000h
OVERLOAD : THE RATED VOLTAGE
5.0
4.0
3.0
JIS C 5201-1 4.25.3
SAMPLE SIZE : n=24pcs
125°C WITH NO LOAD 1,000h
5.0
4.0
3.0
2.0
2.0
∆R/R (%)
∆R/R (%)
1k
RESISTANCE (Ω)
RESISTANCE (Ω)
1.0
0
−1.0
1.0
0
−1.0
−2.0
−2.0
−3.0
−3.0
−4.0
−4.0
−5.0
−6.0
100
−5.0
56
100
1k
10k
100k
RESISTANCE (Ω)
Fig.8 Endurance at 70°C
−6.0
56
100
1k
10k
100k
RESISTANCE (Ω)
Fig.9 Endurance
Rev.B
4/4
Appendix
Notes
No technical content pages of this document may be reproduced in any form or transmitted by any
means without prior permission of ROHM CO.,LTD.
The contents described herein are subject to change without notice. The specifications for the
product described in this document are for reference only. Upon actual use, therefore, please request
that specifications to be separately delivered.
Application circuit diagrams and circuit constants contained herein are shown as examples of standard
use and operation. Please pay careful attention to the peripheral conditions when designing circuits
and deciding upon circuit constants in the set.
Any data, including, but not limited to application circuit diagrams information, described herein
are intended only as illustrations of such devices and not as the specifications for such devices. ROHM
CO.,LTD. disclaims any warranty that any use of such devices shall be free from infringement of any
third party's intellectual property rights or other proprietary rights, and further, assumes no liability of
whatsoever nature in the event of any such infringement, or arising from or connected with or related
to the use of such devices.
Upon the sale of any such devices, other than for buyer's right to use such devices itself, resell or
otherwise dispose of the same, no express or implied right or license to practice or commercially
exploit any intellectual property rights or other proprietary rights owned or controlled by
ROHM CO., LTD. is granted to any such buyer.
Products listed in this document are no antiradiation design.
The products listed in this document are designed to be used with ordinary electronic equipment or devices
(such as audio visual equipment, office-automation equipment, communications devices, electrical
appliances and electronic toys).
Should you intend to use these products with equipment or devices which require an extremely high level of
reliability and the malfunction of with would directly endanger human life (such as medical instruments,
transportation equipment, aerospace machinery, nuclear-reactor controllers, fuel controllers and other
safety devices), please be sure to consult with our sales representative in advance.
About Export Control Order in Japan
Products described herein are the objects of controlled goods in Annex 1 (Item 16) of Export Trade Control
Order in Japan.
In case of export from Japan, please confirm if it applies to "objective" criteria or an "informed" (by MITI clause)
on the basis of "catch all controls for Non-Proliferation of Weapons of Mass Destruction.
Appendix1-Rev1.1