ROHM MCR50JZHJS

MCR50
Resistors
Thick film rectangular Low resistance series
MCR50 (5025 size (2010 size) : 1 / 2W)
zFeatures
1) Highly reliable chip resistor
Ruthenium oxide dielectric offers superior resistance to the elements.
2) Electrodes not corroded by soldering
Suitable for re-flow soldering.
3) ROHM resistors have approved ISO-9001 certification. Design and specifications are subject to change without notice.
Carefully check the specification sheet supplied with the product before using or ordering it.
zRatings
Item
Rated power
Conditions
Specifications
Power must be derated according to the power derating curve in
Figure 1 when ambient temperature exceeds 70˚C.
0.5W (1 / 2W)
at 70°C
POWER LOAD (%)
100
80
60
40
20
0
−55
0
70
100
125
AMBIENT TEMPERATURE (°C)
Fig.1
Rated voltage
The voltage rating is calculated by the following equation. If the value
obtained exceeds the limiting element voltage, the voltage rating is
equal to the maximum operating voltage.
E=
Nominal resistance
P×R
E: Rated voltage (V)
P: Rated power (W)
R: Nominal resistance (Ω)
Limiting element voltage
2.23V(10Ω)
See Table 1.
−55°C to +125°C
Operating temperature
Table 1
Resistance tolerance Special code
F (±1%)
J (±5%)
L
Resistance range
(Ω)
Resistance temperature coefficient
(ppm / ˚C)
0.15≤R≤9.1
(E24)
±250
L
0.1≤R≤0.13
(E24)
400±200
S
0.047≤R≤0.091 (E24)
500±300
L
0.15≤R≤0.91
(E24)
±250
L
0.1≤R<0.13
(E24)
400±200
S
0.047≤R≤0.091 (E24)
500±300
•Before using components in circuits where they will be exposed to transients such as pulse loads (short-duration, high-level loads), be certain to evaluate the
component in the mounted state. In addition, the reliability and performance of this component cannot be guaranteed if it is used with a steady state voltage that
is greater than its rated voltage.
Rev.A
1/3
MCR50
Resistors
zCharacteristics
Guaranteed value
Resistor type
Item
Test conditions (JIS C 5201-1)
J : ±5%
F : ±1%
Resistance
JIS C 5201-1 4.5
Load voltage : A
Measuring method : measure upper termination
by 4 proves.
Upper termination
Prove
Variation of resistance
with temperature
See Table.1
JIS C 5201-1 4.8
Measurement : +25 / −55 / +25 / +125°C
Overload
± (2.0%+0.005Ω)
JIS C 5201-1 4.13
Rated voltage (current) ×2.5, 2s.
A new uniform coating of minimum of
95% of the surface being immersed
and no soldering damage.
JIS C 5201-1 4.17
Rosin-Ethanol (25%WT)
Soldering condition : 235±5°C
Duration of immersion : 2.0±0.5s.
± (1.0%+0.005Ω)
No remarkable abnormality on the appearance.
JIS C 5201-1 4.18
Soldering condition : 260±5°C
Duration of immersion : 10±1s.
± (1.0%+0.005Ω)
JIS C 5201-1 4.19
Test temp. : −55°C to +125°C 5cyc
± (3.0%+0.005Ω)
JIS C 5201-1 4.24
40°C, 93%RH
Test time : 56days
± (3.0%+0.005Ω)
JIS C 5201-1 4.25.1
70°C, Rated voltage
1.5h : ON − 0.5h : OFF
Test time : 1,000h
± (3.0%+0.005Ω)
JIS C 5201-1 4.25.3
125°C
Test time : 1,000h to 1,048h
± (0.5%+0.005Ω)
JIS C 5201-1 4.29
23°C±5°C
Solvent : 2-propanol
Without mechanical damage such as breaks.
JIS C 5201-1 4.33
Solderability
Resistance to
soldering heat
Rapid change of
temperature
Damp heat, steady state
Endurance at 70°C
Endurance
Resistance to solvent
Bend strength of
the end face plating
zDimensions (Unit: mm)
1
0.6±0.25
2
1
Resistive element
2
Silver thick film electrode
3
Nickel electrode
4
Sn electrode
5
Alumina substrate
6
Overcoating
4
2.5±0.15
5
0.55±0.15
0.6±0.25
5.0±0.15
Material
No.
3
6
Rev.A
2/3
MCR50
Resistors
zPackaging
Reel
Taping
P0
P2
B0
02
04
06
08
06
D
04
B
02
A
08
W
F
E
0
φD
A0
K
P1
(Unit : mm)
C
Label
EIAJ ET-7200B compliant
(Unit : mm)
W
F
E
A0
B0
12.0±0.3
5.5±0.05
1.75±0.1
3.4±0.2
5.6±0.2
A
B
C
D
D0
P0
P1
P2
K
0
φ180
−1.5
+1
φ60
0
+1.0
13
0
φ13±0.2
φ1.5 +0.1
0
4.0±0.1
4.0±0.1
2.0±0.05
Max. 1.1
zPart No. Explanation
M C R 5 0
J Z H
Part No.
Resistance tolerance Special part number
F
J
J
±1%
±5%
L
L
10Ω less than (class F)
1Ω less than (class J)
S
0.1Ω less than
Nominal resistance
Resistance code, 3 or 4 digits.
Resistance
Resistance
tolerance
code
+Special P/N
FL,FS,JS
JL
:
:
4 digits
3 digits
Packaging Specifications Code
Part No.
Code
MCR50
JZH
Resistance tolerance
J(±5%)
F(±1%)
Packaging specifications
Reel
Basic ordering unit(pcs)
Embossed tape (4mm Pitch)
φ180mm (7in.)
4,000
Reel (φ180) : JEITA ET-7200B
: Standard product
Rev.A
3/3
Appendix
Notes
No technical content pages of this document may be reproduced in any form or transmitted by any
means without prior permission of ROHM CO.,LTD.
The contents described herein are subject to change without notice. The specifications for the
product described in this document are for reference only. Upon actual use, therefore, please request
that specifications to be separately delivered.
Application circuit diagrams and circuit constants contained herein are shown as examples of standard
use and operation. Please pay careful attention to the peripheral conditions when designing circuits
and deciding upon circuit constants in the set.
Any data, including, but not limited to application circuit diagrams information, described herein
are intended only as illustrations of such devices and not as the specifications for such devices. ROHM
CO.,LTD. disclaims any warranty that any use of such devices shall be free from infringement of any
third party's intellectual property rights or other proprietary rights, and further, assumes no liability of
whatsoever nature in the event of any such infringement, or arising from or connected with or related
to the use of such devices.
Upon the sale of any such devices, other than for buyer's right to use such devices itself, resell or
otherwise dispose of the same, no express or implied right or license to practice or commercially
exploit any intellectual property rights or other proprietary rights owned or controlled by
ROHM CO., LTD. is granted to any such buyer.
Products listed in this document are no antiradiation design.
The products listed in this document are designed to be used with ordinary electronic equipment or devices
(such as audio visual equipment, office-automation equipment, communications devices, electrical
appliances and electronic toys).
Should you intend to use these products with equipment or devices which require an extremely high level of
reliability and the malfunction of with would directly endanger human life (such as medical instruments,
transportation equipment, aerospace machinery, nuclear-reactor controllers, fuel controllers and other
safety devices), please be sure to consult with our sales representative in advance.
About Export Control Order in Japan
Products described herein are the objects of controlled goods in Annex 1 (Item 16) of Export Trade Control
Order in Japan.
In case of export from Japan, please confirm if it applies to "objective" criteria or an "informed" (by MITI clause)
on the basis of "catch all controls for Non-Proliferation of Weapons of Mass Destruction.
Appendix1-Rev1.1