IPM24S0C0R03 - Delta Electronics

FEATURES

High efficiency: 95.0% @ 20Vin, 15.0V/3A

Small size and low profile:
17.8x15.0x7.8mm (0.70”x0.59”x0.31”)

Output voltage adjustment: 8.0V~15.0V

Monotonic startup into normal and
pre-biased loads

Input UVLO, output OCP

Remote ON/OFF

Output short circuit protection

Fixed frequency operation

Copper pad to provide excellent thermal
performance

ISO 9001, TL 9000, ISO 14001, QS9000,
OHSAS18001 certified manufacturing
facility

UL/cUL 60950 (US & Canada) Recognized,
and TUV (EN60950) Certified

CE mark meets 73/23/EEC and 93/68/EEC
directives
Delphi Series IPM24S0C0, Non-Isolated,
Integrated Point-of-Load Power Modules:
20V~36V input, 8.0~15.0V and 3A Output
OPTIONS

SMD or SIP package
The Delphi Series IPM24S0C0 non-isolated, fully integrated
Point-of-Load (POL) power modules, are the latest offerings from a
world leader in power systems technology and manufacturing —
Delta Electronics, Inc. This product family provides up to 3A of
output current or 45W of output power in an industry standard,
compact, IC-like, molded package. It is highly integrated and does
not require external components to provide the point-of-load
function. A copper pad on the back of the module; in close contact
with the internal heat dissipation components; provides excellent
thermal performance. The assembly process of the modules is fully
automated with no manual assembly involved. These converters
possess outstanding electrical and thermal performance, as well as
extremely high reliability under highly stressful operating conditions.
IPM24S0C0 operates from a 20V~36V source and provides a
programmable output voltage from 8.0V to 15.0V. The IPM product
family is available in either a SMD or SIP package. IPM24S family is
also available for output 1.2V~2.5V or 3.3V~6.5V. Please refer to
IPM24S0A0 and IPM24S0B0 datasheets for details.
DATASHEET
IPM24S0C0S/R03_01092009
APPLICATIONS

Telecom/DataCom

Wireless Networks

Optical Network Equipment

Server and Data Storage

Industrial/Test Equipment
TECHNICAL SPECIFICATIONS
TA = 25°C, airflow rate = 300 LFM, Vin = 24Vdc, nominal Vout unless otherwise noted.
PARAMETER
NOTES and CONDITIONS
IPM24S0C0R/S03FA
Min.
ABSOLUTE MAXIMUM RATINGS
Input Voltage (Continuous)
Operating Temperature
Storage Temperature
INPUT CHARACTERISTICS
Operating Input Voltage
Input Under-Voltage Lockout
Turn-On Voltage Threshold
Turn-Off Voltage Threshold
Maximum Input Current
No-Load Input Current
Off Converter Input Current
Input Reflected-Ripple Current
Input Voltage Ripple Rejection
OUTPUT CHARACTERISTICS
Output Voltage Set Point
Output Voltage Adjustable Range
Output Voltage Regulation
Over Line
Over Load
Over Temperature
Total Output Voltage Range
Output Voltage Ripple and Noise
Peak-to-Peak
RMS
Output Current Range
Output Voltage Over-shoot at Start-up
Output DC Current-Limit Inception
DYNAMIC CHARACTERISTICS
Dynamic Load Response
Positive Step Change in Output Current
Negative Step Change in Output Current
Setting Time to 10% of Peak Devitation
Turn-On Transient
Start-Up Time, From On/Off Control
Start-Up Time, From Input
Output Voltage Rise Time
Maximum Output Startup Capacitive Load
EFFICIENCY
Vo=8.0V
Vo=15.0V
FEATURE CHARACTERISTICS
Switching Frequency
ON/OFF Control, (Logic High-Module ON)
Logic High
Logic Low
ON/OFF Current
Leakage Current
GENERAL SPECIFICATIONS
Calculated MTBF
Weight
Please refer to Fig.32 for the measuring point
Typ.
Max.
Units
0
-40
-55
40
125
125
Vdc
°C
°C
20
36
V
19.3
18.8
Vin=Vin,min to Vin,max, Io=Io,max
50
3
60
TBD
P-P 0.5µH inductor, 5Hz to 20MHz
120 Hz
Vin=24V, Io=Io,max, Ta=25℃
Vin=Vin,min to Vin,max
Io=Io,min to Io,max
Ta=Ta,min to Ta,max
Over sample load, line and temperature
5Hz to 20MHz bandwidth
Full Load, 1µF ceramic, 100µF OS-conx2
Full Load, 1µF ceramic, 100µF OS-conpx2
Vo>8.0Vdc
Vin=20V to 36V, Io=0A to 3A, Ta=25℃
7.88
8.0
8.0
0.3
0.3
0.01
-3.0
50
25
10
150
V
V
A
mA
mA
mAp-p
dB
8.12
15.0
Vdc
V
0.025
+3.0
% Vo,set
% Vo,set
%Vo,set/℃
% Vo,set
100
50
3
1
mVp-p
mV
A
% Vo,set
% Io
75
75
200
200
200
300
mVpk
mVpk
µs
5
17
17
9
50
50
17
200
1200
ms
ms
ms
µF
µF
89.0
91.5
91.0
93.5.
%
%
300
kHz
0
0
130
100µFX2 OS-CON & 1µF Ceramic load cap, 0.5A/µs
50% Io, max to 100% Io, max
100% Io, max to 50% Io, max
Io=Io.max
Time for Vo to rise from 10% to 90% of Vo,set,
Full load; ESR ≧15mΩ
Full load; ESR ≧12mΩ
Vin=24V, Io=Io,max, Ta=25℃
Vin=24V, Io=Io,max, Ta=25℃
Module On
Module Off
Ion/off at Von/off=0
Logic High, Von/off=5V
Io=80% Io,max, Ta=25℃
2.4
-0.2
0.25
13.04
6
Vin,max
0.8
1
50
V
V
mA
µA
M hours
grams
DS_IPM24S0C0_01092009
2
ELECTRICAL CHARACTERISTICS CURVES
Figure 1: Converter efficiency vs. output current
(8.0V output voltage)
Figure 2: Converter efficiency vs. output current
(15.0V output voltage)
Figure 3: Output ripple & noise at 36Vin, 8.0V/3A out
Figure 4: Output ripple & noise at 36Vin, 15.0V/3A out
Figure 5: Power on waveform at 24vin, 8.0V/3A out with
Figure 6: Power on waveform at 24vin, 8.0V/3A out with
application of Vin
application of Vin
DS_IPM24S0C0_01092009
3
ELECTRICAL CHARACTERISTICS CURVES
Figure 7: Power off waveform at 24vin, 8.0V/3A out with
application of Vin
Figure 8: Power off waveform 24vin,15.0V/3A out with
application of Vin
Figure 9: Remote turn on delay time at 24vin, 8.0V/3A out
Figure 10: Remote turn on delay time at 24vin, 8.0V/3A out
Figure 11: Turn on delay at 24vin, 8.0V/3A out with
application of Vin
Figure 12: Turn on delay at 24vin, 15.0V/3A out with
application of Vin
DS_IPM24S0C0_01092009
4
ELECTRICAL CHARACTERISTICS CURVES
Figure 13: Typical transient response to step load change at
0.5A/μS from 100% to 50% of Io, max at 24Vin,
15.0V out (measurement with a 1uF ceramic
Figure 14: Typical transient response to step load change at
0.5A/μS from 50% to 100% of Io, max at36Vin,
6.5V out (measurement with a 1uF ceramic)
DS_IPM24S0C0_01092009
5
TEST CONFIGURATIONS
DESIGN CONSIDERATIONS
Input Source Impedance
L
VI(+)
2 100uF
Electrolytic
BATTERY
3.3uF
Ceramic
VI(-)
Note: Input reflected-ripple current is measured with a
simulated source inductance. Current is
measured at the input of the module.
Figure 15: Input reflected-ripple current test setup
To maintain low-noise and ripple at the input voltage, it is
critical to use low ESR capacitors at the input to the
module. Figure 26 shows the input ripple voltage
(mVp-p) for various output models using 2x100uF low
ESR electrolytic capacitors (Rubycon P/N:50YXG100,
100uF/50V or equivalent) and 1x3.3.0 uF very low ESR
ceramic capacitors (TDK P/N: C4532JB1H335M,
3.3uF/50V or equivalent).
The input capacitance should be able to handle an AC
ripple current of at least:
Irms  Iout
Vout 
Vout 
1 

Vin 
Vin 
Arms
Vo
100uFx2 1uF
OS-con ceramic
SCOPE
Resistive
Load
GND
Note: Use a 100μFx2 OS-son and 1μF capacitor. Scope
measurement should be made using a BNC
connector.
Figure 16: Peak-peak output noise and startup transient
measurement test setup
VI
Figure 18: Input ripple voltage for various output models,
Io = 3A (Cin =2x100uF electrolytic capacitors
1x3.3uF ceramic capacitors at the input)
Vo
GND
The power module should be connected to a low
ac-impedance input source. Highly inductive source
impedances can affect the stability of the module. An
input capacitance must be placed close to the modules
input pins to filter ripple current and ensure module
stability in the presence of inductive traces that supply
the input voltage to the module.
Figure 17: Output voltage and efficiency measurement test
setup
Note: All measurements are taken at the module
terminals. When the module is not soldered (via
socket), place Kelvin connections at module
terminals to avoid measurement errors due to
contact resistance.
(
Vo  Io
)  100 %
Vi  Ii
DS_IPM24S0C0_01092009
6
DESIGN CONSIDERATIONS
FEATURES DESCRIPTIONS
Remote On/Off
Over-Current Protection
The IPM series power modules have an On/Off control
pin for output voltage remote On/Off operation. The
On/Off pin is an open collector/drain logic input signal
that is referenced to ground. When On/Off control pin is
not used, leave the pin unconnected.
To provide protection in an output over load fault
condition, the unit is equipped with internal over-current
protection. When the over-current protection is
triggered, the unit enters hiccup mode. The units
operate normally once the fault condition is removed.
The remote on/off pin is internally connected to +5Vdc
through an internal pull-up resistor. Figure 27 shows the
circuit configuration for applying the remote on/off pin.
The module will execute a soft start ON when the
transistor Q1 is in the off state.
Output Voltage Programming
The typical rise for this remote on/off pin at the output
voltage of 2.5V and 5.0V are shown in Figure 17 and 18.
Vo
Vin
The output voltage shall be externally adjustable by use
of a Trim pin. The module output shall be adjusted by
either a voltage source referenced to ground or an
external resistor be connected between trim pin and Vo or
ground. To trim-down using an external resistor, connect
a resistor between the Trim and Vo pin of the module. To
trim up using an external resistor, connect the resistor
between the Trim and ground pins of the module. The
value of resistor is defined below. The module outputs
shall not be adversely affected (regulation and operation)
when the Trim pin is left open.
IPM
On/Off
RL
Q1
IPM can also be programmed by applying a voltage
between the TRIM and GND pins (Figure 20). The
following equation can be used to determine the value of
Vtrim needed for a desired output voltage Vadj:
GND
Trim up
Figure 19: Remote on/off implementation
Rtrim =
(Vout-0.7)*1.91
Vadj-Vout
(KΩ )
(Vadj-0.7)*20
Vout-Vadj
(KΩ )
Trim Down
Rtrim =
Rtrim is the external resistor in KΩ
Vadj is the desired output voltage
DS_IPM24S0C0_01092009
7
FEATURES DESCRIPTIONS (CON.)
Table 1 Rtrim is the external resistor in KΩ;
Vout is the desired output voltage
Output
Measurement
R.trim_Up R.trim_Down
0A
NC
V
NC
2K
V
NC
Rtrim setting (Ω)
Vo
8.0
Vadj
15.0
NC
Vadj 8.0*(1-10%)
Figure 20:
Trim up Circuit configuration for programming
output voltage using an external resistor
Vout
Rtrim
215K
V
The amount of power delivered by the module is the
voltage at the output terminals multiplied by the output
current. When using the trim feature, the output voltage
of the module can be increased, which at the same
output current would increase the power output of the
module. Care should be taken to ensure that the
maximum output power of the module must not exceed
the maximum rated power (Vo.set x Io.max ≤ P max).
Load
Trim
Voltage Margining
GND
Figure 21:
Trim down Circuit configuration for programming
output voltage using an external resistor
Output voltage margining can be implemented in the IPM
modules by connecting a resistor, R margin-up, from the Trim
pin to the ground pin for margining-up the output voltage
and by connecting a resistor, R margin-down, from the Trim pin
to the output pin for margining-down. Figure 32 shows
the circuit configuration for output voltage margining. If
unused, leave the trim pin unconnected.
Vo
Vin
IPM
Rmargin-down
Q1
On/Off
Trim
Rmargin-up
Figure 22: Circuit configuration for programming output voltage
using external voltage source
Table 1 provides Rtrim values required for some common
output voltages. By using a 0.5% tolerance resistor, set
point tolerance of ±2% can be achieved as specified in the
electrical specification.
Rtrim
Q2
GND
Figure 23: Circuit configuration for output voltage margining
DS_IPM24S0C0_01092009
8
THERMAL CONSIDERATIONS
THERMAL CURVES
Thermal management is an important part of the system
design. To ensure proper, reliable operation, sufficient
cooling of the power module is needed over the entire
temperature range of the module. Convection cooling is
usually the dominant mode of heat transfer.
Hence, the choice of equipment to characterize the
thermal performance of the power module is a wind
tunnel.
Thermal Testing Setup
Delta’s DC/DC power modules are characterized in
heated vertical wind tunnels that simulate the thermal
environments encountered in most electronics
equipment. This type of equipment commonly uses
vertically mounted circuit cards in cabinet racks in which
the power modules are mounted.
The following figure shows the wind tunnel
characterization setup. The power module is mounted on
a test PWB and is vertically positioned within the wind
tunnel. The height of this fan duct is constantly kept at
25.4mm (1’’).
Figure 25: Temperature measurement location
* The allowed maximum hot spot temperature is defined at 125 ℃.
IPM24S (Standard) Output Current vs. Ambient Temperature and Air Velocity
@ Vin=24V, Vout = 8V (Either Orientation)
Output Current(A)
3
Natural
Convection
Thermal Derating
2
Heat can be removed by increasing airflow over the
module. To enhance system reliability, the power
module should always be operated below the maximum
operating temperature. If the temperature exceeds the
maximum module temperature, reliability of the unit may
be affected.
100LFM
200LFM
300LFM
1
0
50
PWB
FACING PWB
55
60
65
70
75
80
85
Ambient Temperature (℃)
Figure 26: Output current vs. ambient temperature and air velocity
@ Vin=24V, Vout=8V(Either Orientation)
MODULE
Output Current(A)
IPM24S (Standard) Output Current vs. Ambient Temperature and Air Velocity
@ Vin=24V, Vout = 15V (Either Orientation)
3
AIR VELOCITY
AND AMBIENT
TEMPERATURE
MEASURED BELOW
THE MODULE
Natural
Convection
50.8 (2.0”)
2
100LFM
200LFM
AIR FLOW
300LFM
1
400LFM
12.7 (0.5”)
25.4 (1.0”)
0
Note: Figure dimensions are in millimeters and (inches)
Figure 24: Wind tunnel test setup
50
55
60
65
70
75
80
85
Ambient Temperature (℃)
Figure 27: Output current vs. ambient temperature and air velocity
@ Vin=24V, Vo=15V(Either Orientation)
DS_IPM24S0C0_01092009
9
PICK AND PLACE LOCATION
SURFACE- MOUNT TAPE & REEL
All dimensions are in millimeters (inches)
All dimensions are in millimeters (inches)
LEAD FREE PROCESS RECOMMEND TEMP. PROFILE
Temp.
20 ~ 40sec.
Peak Temp. 240 ~ 245 0 C
217 0 C
Ramp down
max. 6.0 0 C/sec
200 0 C
150 0 C
Preheat time
60 ~ 180 sec.
Time 60 ~ 150 sec.
Above 217 0 C
Ramp up
max. 3.0 0 C/sec
25 0 C
Time
Note: All temperature refers to topside of the package, measured on the package body surface.
DS_IPM24S0C0_01092009
10
Mechanical Drawing
SMD PACKAGE
SIP PACKAGE
1 2 3 4 5
RECOMMEND PWB PAD LAYOUT
RECOMMEND PWB HOLE LAYOUT
7
6
1 2 3 4 5
1 2 3 4 5
Note: The copper pad is recommended to connect to the ground.
ALL DIMENSION ARE IN MILLIMETERS (INCHES)
STANDARD DIMENSION TOLERANCE IS ± 0.10(0.004”)
DS_IPM24S0C0_01092009
11
PART NUMBERING SYSTEM
IPM
24
S
0C0
S
03
F
Product
Family
Input
Voltage
Number of
Outputs
Output Voltage
Package
Output
Current
Integrated POL
Module
24 -20V ~
36V
S - Single
0C0 - programmable output
8.0V~15.0V
R - SIP
S - SMD
03 - 3A
A
Option Code
F- RoHS 6/6
A - Standard Function
(Lead Free)
MODEL LIST
Model Name
Input Voltage
Output Voltage
Output Current
Efficiency (Full load@12Vin)
IPM24S0A0S/R03FA
8V ~ 36V
1.2V ~ 2.5V
3A
85%
IPM24S0B0S/R03FA
11V ~ 36V
3.3V ~ 6.5V
3A
91%
Model Name
Input Voltage
Output Voltage
Output Current
Efficiency (Full load@20Vin)
IPM24S0C0S/R03FA
20V ~ 36V
8.0V~15.0V
3A
95%
CONTACT: www.deltaww.com/dcdc
USA:
Telephone:
East Coast: 978-656-3993
West Coast: 510-668-5100
Fax: (978) 656 3964
Email: [email protected]
Europe:
Telephone: +31-20-655-0967
Fax: +31-20-655-0999
Email: [email protected]
Asia & the rest of world:
Telephone: +886 3 4526107
Ext 6220~6224
Fax: +886 3 4513485
Email: [email protected]
WARRANTY
Delta offers a two (2) year limited warranty. Complete warranty information is listed on our web site or is available upon
request from Delta.
Information furnished by Delta is believed to be accurate and reliable. However, no responsibility is assumed by Delta
for its use, nor for any infringements of patents or other rights of third parties, which may result from its use. No license
is granted by implication or otherwise under any patent or patent rights of Delta. Delta reserves the right to revise these
specifications at any time, without notice.
DS_IPM24S0C0_01092009
12