GOT5100T-834 All-in-One 10.4” SVGA TFT Fanless Touch Panel Computer with Intel® Celeron® Processor J1900 onboard User’s Manual Disclaimers This manual has been carefully checked and believed to contain accurate information. Axiomtek Co., Ltd. assumes no responsibility for any infringements of patents or any third party’s rights, and any liability arising from such use. Axiomtek does not warrant or assume any legal liability or responsibility for the accuracy, completeness or usefulness of any information in this document. Axiomtek does not make any commitment to update the information in this manual. Axiomtek reserves the right to change or revise this document and/or product at any time without notice. No part of this document may be reproduced, stored in a retrieval system, or transmitted, in any form or by any means, electronic, mechanical, photocopying, recording, or otherwise, without the prior written permission of Axiomtek Co., Ltd. CAUTION If you replace wrong batteries, it causes the danger of explosion. It is recommended by the manufacturer that you follow the manufacturer’s instructions to only replace the same or equivalent type of battery, and dispose of used ones. Copyright 2014 Axiomtek Co., Ltd. All Rights Reserved September 2014, Version A1 Printed in Taiwan ii Safety Precautions Before getting started, read the following important cautions. 1. Be sure to ground yourself to prevent static charge when installing the internal components. Use a grounding wrist strap and place all electronic components in any static-shielded devices. Most electronic components are sensitive to static electrical charge. 2. Disconnect the power cords from the GOT5100T-834 Series before making any installation. Be sure both the system and the external devices are turned OFF. Sudden surge of power could ruin sensitive components. Make sure the GOT5100T-834 Series is properly grounded. 3. Do not open the system’s top cover. If opening the cover for maintenance is a must, only a trained technician is allowed to do so. Integrated circuits on computer boards are sensitive to static electricity. To avoid damaging chips from electrostatic discharge, observe the following precautions: Before handling a board or integrated circuit, touch an unpainted portion of the system unit chassis for a few seconds. This will help to discharge any static electricity on your body. When handling boards and components, wear a wrist-grounding strap, available from most electronic component stores. Trademarks Acknowledgments Axiomtek is a trademark of Axiomtek Co., Ltd. ® Windows is a trademark of Microsoft Corporation. IBM, PC/AT, PS/2, VGA are trademarks of International Business Machines Corporation. ® ® Intel and Pentium are trademarks of Intel Corporation. AMI is trademark of American Megatrend Inc. Other brand names and trademarks are the properties and registered brands of their respective owners. iii Table of Contents Disclaimers ..................................................................................................... ii Safety Precautions ........................................................................................ iii Chapter 1 Introduction ............................................. 1 1.1 General Description ............................................................................ 1 1.2 Specifications ...................................................................................... 2 1.3 Dimensions .......................................................................................... 4 1.4 I/O Outlets ............................................................................................ 6 1.5 Packing List ......................................................................................... 7 Chapter 2 Hardware and Installation ...................... 9 2.1 CFast™ card Installation .................................................................. 10 2.2 SBC87834 Jumpers and Connectors............................................... 11 2.2.1 2.2.2 Jumper Settings ........................................................................................ 13 Connectors ................................................................................................ 14 2.3 Ethernet.............................................................................................. 24 2.4 Mountings – Panel/Wall/Desktop/VESA .......................................... 25 2.4.1 2.4.2 2.4.3 2.4.4 Panel Mounting ......................................................................................... 25 Wall-Mounting ........................................................................................... 26 Desktop-Mounting ..................................................................................... 26 VESA-ARM Mounting ................................................................................ 28 2.5 HDD Installation................................................................................. 29 2.6 DRAM Installation.............................................................................. 31 2.7 Mini cards Card Installation.............................................................. 33 2.7.1 2.7.2 2.8 Wireless LAN Card Installation ................................................................. 33 mSATA Card Installation ............................................................................ 35 Power Input (Phoenix type) .............................................................. 36 Chapter 3 AMI BIOS Setup Utility .......................... 37 3.1 Navigation Keys ................................................................................ 37 3.2 Main Menu.......................................................................................... 38 3.3 Advanced Menu ................................................................................. 39 3.4 Chipset Menu ..................................................................................... 48 3.5 Security .............................................................................................. 51 3.6 Boot Menu.......................................................................................... 52 iv 3.7 Save&Exit........................................................................................... 53 Chapter 4 4.1 System ............................................................................................... 55 4.1.1 4.1.2 4.2 Win 7 ......................................................................................................... 55 Win 8/8.x ................................................................................................... 56 Touch Screen ..................................................................................... 56 4.2.1 4.2.2 4.3 Drivers Installation .............................. 55 Specification .............................................................................................. 56 Driver Installation- Windows 7/8.x ............................................................. 57 Embedded O.S. .................................................................................. 59 4.3.1 WES 7 & WE8S......................................................................................... 59 Appendix A Watchdog Timer ................................... 61 About Watchdog Timer ................................................................................ 61 How to Use Watchdog Timer....................................................................... 61 WDT Sample Program ................................................................................. 62 Appendix B Backlight Control ................................. 65 About Backlight Control .............................................................................. 65 How to Use Backlight Control..................................................................... 65 Removed Brightness Control Tool ............................................................. 74 v This page is intentionally left blank. vi GOT5100T-834 User’s Manual Chapter 1 Introduction This chapter contains general information and detailed specifications of the GOT5100T-834. Chapter 1 includes the following sections: General Description Specifications Dimensions I/O Outlets Package List 1.1 General Description The GOT5100T-834 is a fan-less and compact-size touch panel computer, equipped with a 10.4” TFT LCD display and low power consumption Intel® Celeron® Processor J1900 (2M Cache, up to 2.42 GHz). The GOT5100T-834 supports Windows 7, Windows 8.x and Windows embedded OS. The panel computer is able to install a CFast™ card or mSATA and provide two Mini card slots for wireless module. Its excellent ID and friendly user interface make it a professional yet easy-to-use panel computer. The GOT5100T-834 is an ideal for space-limited applications in factory automation, machine maker operating systems, building automation, and more. GOT5100T-834: 10.4” TFT SVGA Fanless Touch Panel Computer Reliable and Stable Design The GOT5100T-834 adopts a fanless cooling system and a CFast™ card, which makes it suitable for vibration environments. Embedded O.S. Supported The GOT5100T-834 not only supports Windows 7 and Windows 8.x, but also supports embedded OS,. For storage device, the GOT5100T-834 supports 2.5” SATA device and CFast™ card or mSATA. Industrial-grade Product Design The GOT5100T-834 has an incredible design to be used in different industrial environments. The front bezel meets the IP65/NEMA4 standard. For connecting other devices, the GOT5100T-834 also features several interfaces: USB, Ethernet, and RS-232/422/485. Introduction 1 GOT5100T-834 User’s Manual 1.2 Specifications Main CPU Board CPU Intel® Celeron® Processor J1900 (2M Cache, up to 2.42 GHz) onboard. System Memory One 204-pin DDR3L SO-DIMM socket Maximum memory up to 8BG BIOS America Megatrends BIOS I/O System Standard I/O Two RSS-232/422/485 Two USB 2.0 Two USB 3.0 Ethernet 2x RJ45 Giga Ethernet (Intel i210IT) Audio One Line out Expansion 1 x Mini-card slot (w/SIM slot) 1 x Mini-card slot (supports mSATA, optional) Storage 2 One CFast™ or mSATA One 2.5” SATA HDD Power connector GOT5100T-834-DC : 9VDC to 36VDC with phoenix power connector or GOT5100T-834-J: External 60W AC Adapter with screw type connector Introduction GOT5100T-834 User’s Manual System Specification 10.4” SVGA(800x600) LCD with LED backlight 5 wired Resistive Touch Fanless Heat Dispensing Design Disk drive housing: Net Weight 2.48 Kgs (5.46 lb) Dimension (Main Body Size) One 2.5” SATA drive 327.5 x 52.5 x 261.8 mm Operation Temperature 0℃ to 50℃ Relative Humidity 10% to 90% @ 40℃, Non-Condensing Vibration 2.0G, 5 to 500 Hz, 2.0 G random for CFast™ card Power input 9~36VDC with phoenix power connector or External 60W AC Adapter — Power Input: 90VAC to 264VAC — Power Output: 12VDC, Max. 5A NOTE All specifications and images are subject to change without notice. NOTE If the operation temperature is higher than 35 ℃, the wide temperature HDD is recommended to be used on the device. NOTE If the operation temperature is higher than 45℃, the wide temperature are recommended to be used on the device. Introduction CFast™ 3 GOT5100T-834 User’s Manual 1.3 Dimensions This diagram shows you dimensions and outlines of the GOT5100T-834. 4 Introduction GOT5100T-834 User’s Manual Introduction 5 GOT5100T-834 User’s Manual 1.4 I/O Outlets Please refer to the following illustration for I/O locations of the GOT5100T-834. 6 No Function No Function 1 POWER SWITCH (ATX) 7 Ethernet (RJ-45) 2 Power Input connector (Screw) 8 Dual USB 3.0 ports 3 Power Input connector (Phoenix) 9 AUDIO (LINE-OUT) 4 Dual USB 2.0 ports 5 COM 2(RS-232/422/485) 6 COM 1(RS-232/422/485) Introduction GOT5100T-834 User’s Manual 1.5 Packing List When you receive the GOT5100T-834, the bundled package should contain the following items: GOT5100T-834 x 1 Panel Mount Kit x 6 Driver CD x1 Wall-Mount Kit x1 HDD Mylar x 1 Screws for HDD x4 Phoenix connector x1 Power Adapter & power cord (for GOT5100T-834-J) (for GOT5100T-834) If you can not find the package or any items are missing, please contact Axiomtek distributors immediately. Introduction 7 GOT5100T-834 User’s Manual This page is intentionally left blank. 8 Introduction GOT5100T-834 User’s Manual Chapter 2 Hardware and Installation The GOT5100T-834 provides rich I/O ports and flexible expansions for you to meet different demand, for example, CFast™ card. The chapter will show you how to install the hardware. It includes: CFast™ Card SBC87834 Jumpers and Connectors Ethernet Mounting Way Hard disk DRAM Wireless LAN Card Power Input Hardware and Installation 9 GOT5100T-834 User’s Manual 2.1 CFast™ card Installation The GOT5100T-834 provides one CF slot for users to install CFast™ card. Please refer to the following instructions for installation: Step 1 Turn off the system, and unplug the power cord. Step 2 Remove the cover of CFast™ socket. Step 3 Locate the CFast™ socket, and insert the card into the socket. 10 Hardware and Installation GOT5100T-834 User’s Manual 2.2 SBC87834 Jumpers and Connectors Component Side Hardware and Installation 11 GOT5100T-834 User’s Manual Solder Side 12 Hardware and Installation GOT5100T-834 User’s Manual 2.2.1 Jumper Settings Making the proper jumper settings configure the SBC87834 to match the needs of your application. The following table shows the default jumper settings for the onboard devices. ★ Default Setting Jumper JP1 JP2 JP4 JP5 JP6 JP7 JP8 JP11 JP12 JP13 JP14 JP15 ★ Panel backlight control PWM mode Panel backlight control DC mode Touch Controller 4,8 WIRE ★ Touch Controller 5 WIRE ★ LVDS Panel Power : 3.3V LVDS Panel Power : 5V Touch OFF ★ Touch ON ★ PCIe device mSATA device AT mode ★ ATX mode ★ Normal Clear CMOS COM3_5VSB ★ COM3_5V ★ COM1 normal mode COM1 pin1 with power :+5V COM1 pin9 with power :+12V ★ COM2 normal mode COM2 pin1 with power :+5V COM2 pin9 with power :+12V ★ COM3 normal mode COM3 pin1 with power :+5V COM3 pin9 with power :+12V ★ COM4 normal mode COM4 pin1 with power :+5V COM4 pin9 with power :+12V Hardware and Installation Jumper Setting Short 1-2 Short 3-4 Short 1-2 Short 2-3 Short 1-2 Short 2-3 Short 1-2 Short 2-3 Short 1-2 Short 2-3 Short 1-2 Short 2-3 Short 1-2 Short 2-3 Short 1-2 Short 2-3 Short 3-5,4-6 Short 1-3,4-6 Shot 3-5,2-4 Short 3-5,4-6 Short 1-3,4-6 Shot 3-5,2-4 Short 3-5,4-6 Short 1-3,4-6 Shot 3-5,2-4 Short 3-5,4-6 Short 1-3,4-6 Shot 3-5,2-4 13 GOT5100T-834 User’s Manual 2.2.2 Connectors The connectors allow the CPU Board to connect with other parts of the system. Ensure that all connectors are in place and firmly attached. The following table lists the function of each connector on the SBC87834. Connectors Label LVDS connector CN1 LVDS inverter connector CN2 TOUCH connector HDD power connector CN3 CN4 Full size min-PCIe connector CN5 FRONT PANEL pin header CN6 SIM card connector CN7 Full size min-PCIe connector CN8 DC IN connector CN9 Digital I/O pin header CN10 Speaker Out & MIC IN connector CN11 VGA connector CN12 Audio connector CN13 USB CONNECTOR (reserved) CN14/CN20 Audio Lin In connector CN15 Power lamp connector CN16 Power button connector CN17 Touch function enable/disable & LED indicator connector CN18 Panel control Keypad connector CN19 CPU FAN FAN1 System FAN FAN2 USB2.0 box header USB1 USB3.0 connector USB2 Display Port connector DP1 SATA connector SATA1 RJ45 LAN connector LAN1, LAN2 Serial Port connector COM1,COM2 Serial Port box header COM3,COM4 CFast connector SCF1 14 Hardware and Installation GOT5100T-834 User’s Manual LVDS connector: CN1 CN1 Pin Assignment Pin Description Pin Description 1 VCC 21 GND 2 VCC 22 GND 3 VCC 23 LVDSA_DATAN0 4 VCC 24 LVDSB_DATAN2 5 VCC 25 LVDSA_DATAP0 6 VCC 26 LVDSB_DATAP2 7 DDC DATA 27 GND 8 DDC CLOCK 28 GND 9 GND 29 LVDSA_DATAN1 10 GND 30 LVDSA_DATAN3 11 LVDSB_DATAN3 31 LVDSA_DATAP1 12 LVDSB_DATAN0 32 LVDSA_DATAP3 13 LVDSB_DATAP3 33 GND 14 LVDSB_DATAP0 34 GND 15 GND 35 LVDSA_DATAN2 16 GND 36 LVDSA_CLKN 17 LVDSB_CLKN 37 LVDSA_DATAP2 18 LVDSB_DATAN1 38 LVDSA_CLKP 19 LVDSB_CLKP 39 GND 20 LVDSB_DATAP1 40 GND Hardware and Installation 15 GOT5100T-834 User’s Manual LVDS inverter connector: CN2 CN2 Pin Assignment Pin Description Pin Description 1 GND 5 Inverter ON-OFF 2 GND 6 +12V 3 GND 7 +12V 4 Backlight control 8 +12V TOUCH connector: CN3 CN3 Pin Assignment Pin Description 1 X+ 2 X- 3 Y+ 4 Sense 5 X+ 6 X- 7 Y+ 8 Y- 9 GND 16 Hardware and Installation GOT5100T-834 User’s Manual HDD power connector: CN4 CN9 Pin Assignment Pin Description 1 +12V 2 GND 3 GND 4 +5V FRONT PANEL pin header: CN6 CN6 Pin Assignment Pin Description Pin Description 1 + 5V 2 Beep 3 GND 4 BUZZER 5 GND 6 Beep 7 NC 8 +5V 9 GND 10 PWBTN 11 GND 12 RESET 13 SATA LED 14 +3.3V Hardware and Installation 17 GOT5100T-834 User’s Manual SIM card connector: CN7 CN7 Pin Assignment Pin Description Pin Description 1 UIM PWR 5 GND 2 UIM RST 6 UIM VPP 3 UIM CLK 7 UIM DATA 4 NC 8 NC Power connector: CN9 CN9 Pin Assignment Pin Description 1 DCIN (9V -36V) 2 DCIN (9V -36V) 3 GND 4 GND 18 Hardware and Installation GOT5100T-834 User’s Manual Digital I/O pin header: CN10 CN10 Pin Assignment Pin Description Pin Description 1 GND 6 GND 2 GPIO0 7 GPIO1 3 GPIO2 8 GPIO3 4 GPIO4 9 GPIO5 5 GPIO6 10 GPIO7 11 GPIO8 12 GPIO9 13 GPIO10 14 GPIO11 15 GPIO12 16 GPIO13 17 GPIO14 18 GPIO15 19 GND 20 GND Speaker Out & MIC IN connector: CN11 CN11 Pin Assignment Pin Description Pin Description 1 SPKOUT_L- 2 SPKOUT_L + 3 SPKOUT_R- 4 SPKOUT_R + 5 MIC IN 6 GND Hardware and Installation 19 GOT5100T-834 User’s Manual VGA Cable Connector: CN12 CN12 Pin Assignment Pin Signal Pin Signal 1 Red 2 GND 3 Green 4 N.C. 5 Blue 6 N.C. 7 VCC 8 DDC DATA 9 GND 10 N.C. 11 GND . 12 Horizontal Sync 13 GND 14 Vertical Sync 15 DCC CLK 16 N.C. USB CONNECTOR (reserved): CN14/CN20 CN14/CN20 Pin Assignment Pin Description 1 VCC 2 D- 3 D+ 4 GND 5 GND 20 Hardware and Installation GOT5100T-834 User’s Manual Audio Lin In connector: CN15 CN15 Pin Assignment Pin Description 1 LINE IN L 2 GND 5 LIN IN R Power lamp connector: CN16 CN16 Pin Assignment Pin Description 1 Power (+5V) Pin 2 Description GND Power button connector: CN17 CN17 Pin Assignment Pin Description 1 Power Button Hardware and Installation Pin 2 Description GND 21 GOT5100T-834 User’s Manual Touch function enable/disable & LED indicator connector: CN18 CN18 Pin Assignment Pin Description 1 ON/OFF button 2 GND 3 LED Panel control Keypad connector: CN19 CN19 Pin Assignment Pin Description 1 GND 2 Panel ON/OFF 3 Abnormal indicate LED 4 Normal indicate LED 5 Blacklight down 6 Blacklight up 22 Hardware and Installation GOT5100T-834 User’s Manual USB box header: USB1 USB1 Pin Assignment Pin Description Pin Description 1 +5V 2 +5V 3 USB- 4 USB- 5 USB+ 6 USB+ 7 GND 8 GND 9 GND 10 GND Serial Port box header: COM3, COM4 COM3, COM4 Pin Assignment Pin Description Pin Description 1 DCD 2 DSR 3 RX 4 RTS 5 TX 6 CTS 7 DTR 8 RI 9 GND 10 NC Hardware and Installation 23 GOT5100T-834 User’s Manual 2.3 Ethernet The GOT5100T-834 is equipped with two high performance Plug and Play Ethernet interfaces, full compliant with IEEE 802.3 standard, and can be connected with a RJ-45 LAN connector. Please refer to detailed pin assignment list below: Pin 24 Signal 1 TX+ (Data transmission positive 2 TX- (Data transmission negative) 3 Rx+(Data reception positive) 4 RJ45 termination 5 RJ45 termination 6 Rx- (Data reception negative) 7 RJ45 termination 8 RJ45 termination 1 2 3 4 5 6 7 8 RJ-45 Hardware and Installation GOT5100T-834 User’s Manual 2.4 Mountings – Panel/Wall/Desktop/VESA There are several mounting ways for the GOT5100T-834, Panel, Wall, Desktop and VESA mountings. 2.4.1 Panel Mounting The GOT5100T-834 is designed for panel mount application. A set of standard mounting kit are bundled with the system package that you can use it to mount the GOT5100T-834. Hardware and Installation 25 GOT5100T-834 User’s Manual 2.4.2 Wall-Mounting The GOT5100T-834 is designed for Wall mounting application. Please refer to the following steps: Fix wall mount bracket on the back of the unit. 2.4.3 Desktop-Mounting The GOT5100T-834 is designed for desktop mounting application. Please refer to the following steps: Step 1 26 Find out the screws as marked on the back side of chassis. Hardware and Installation GOT5100T-834 User’s Manual Step 2 Assemble the desktop stand to the chassis, and fix the screws. CAUTION： USE RECOMMENDED/SUITABLE MOUNTING APPARATUS TO AVOID RISK OF INJURY. Hardware and Installation 27 GOT5100T-834 User’s Manual 2.4.4 VESA-ARM Mounting CAUTION： USE RECOMMENDED/SUITABLE MOUNTING APPARATUS TO AVOID RISK OF INJURY. Step 1 Find out the screws as marked on the back side of chassis. Step 2 Assemble the VESA-ARM to the back side of the chassis, and fix the screws. Step 3 VESA mounting Installation completed. CAUTION： 28 USERECOMMENDED/SUITABLE MOUNTING APPARATUS TO AVOIDE RISK OF INJURY. Hardware and Installation GOT5100T-834 User’s Manual 2.5 HDD Installation The GOT5100T-834 provides a convenient Hard Disk Drive (HDD) bracket for users to install 2.5” SATA HDD. Please follow the steps: . Step 1 Unscrew eight screws to remove the back cover. Step 2 Unscrew 4 screws from the HDD bracket, and take out HDD bracket. Hardware and Installation 29 GOT5100T-834 User’s Manual Step 3 Screw the 2.5” HDD to the HDD bracket. Step 4 Fix the HDD bracket into the system, and plug the data and power cable to HDD. Installation complete. 30 Hardware and Installation GOT5100T-834 User’s Manual 2.6 DRAM Installation The GOT5100T-834 provides one 204-pin DDR3L SODIMM socket that support system memory up to 8GB. Please follow steps below to install the memory modules: Step 1 Open the back cover and find out the DIMM socket on main board(SBC87834). Step 2 Insert the DRAM to the DIMM socket, and then push it down firmly until it is clipped by the socket. Hardware and Installation 31 GOT5100T-834 User’s Manual Step 3 32 Install the memory module into the socket and push it firmly down until it is fully seated. The socket latches are levered upwards and clipped on to the edges of the DIMM. Hardware and Installation GOT5100T-834 User’s Manual 2.7 Mini cards Card Installation 2.7.1 Wireless LAN Card Installation The GOT5100T-834 provides two Mini card slots for user to install wireless LAN cards. You can choose either slot 1 or slot 2 to install the wireless LAN card and refer to the following instructions and illustration: Step 1 Open the back cover and find out the mini-card slot on main board. Step 2 Insert the wireless LAN card to the slot. Screw it firmly on the slot. Hardware and Installation 33 GOT5100T-834 User’s Manual Step 3 Find the built-in Antenna cable. Step 4 There are two connectors on wireless LAN card. One is MAIN, and the other is auxiliary. Connect antenna cable to MAIN connector on wireless LAN card. 34 Hardware and Installation GOT5100T-834 User’s Manual 2.7.2 mSATA Card Installation The GOT5100T-834 provides one Mini card slot for user to install mSATA. Please choose the slot 2 when installing the mSATA card and refer to the following instructions and illustration: Step 1 Open the back cover and find out the mini-card slot on main board. Step 2 Insert the mSATA card to the slot 2. Screw it firmly on the slot. NOTE Please set the jumper JP6 in 2-3 when using the mSATA. NOTE The screws of mini card slots are M12 type. Hardware and Installation 35 GOT5100T-834 User’s Manual 2.8 Power Input (Phoenix type) GOT5100T-834 equips with a phoenix type power connector. It adopts 9VDC to 36VDC. Please follow the signs on power connector to connect DC power source. +: Power positive NOTE 36 G: Safety ground －:Power negative The safety ground must be connected to ensure the unit working appropriately. Hardware and Installation GOT5100T-834 User’s Manual Chapter 3 AMI BIOS Setup Utility This chapter provides users with detailed description how to set up basic system configuration through the AMIBIOS8 BIOS setup utility. 3.1 Navigation Keys The BIOS setup/utility uses a key-based navigation system called hot keys. Most of the BIOS setup utility hot keys can be used at any time during the setup navigation process. These keys include <F1>, <F2>, <F3>, <F4>, <Enter>, <ESC>, <Arrow> keys, and so on. NOTE Some of navigation keys differ from one screen to another. Left/Right The Left and Right <Arrow> keys allow you to select a setup screen. Up/Down The Up and Down <Arrow> keys allow you to select a setup screen or sub-screen. + Plus/Minus The Plus and Minus <Arrow> keys allow you to change the field value of a particular setup item. Tab The <Tab> key allows you to select setup fields. F1 The <F1> key allows you to display the General Help screen. F2 The <F2> key allows you to load previous value F3 The <F3> key allows you to Load Optimized Defaults. F4 The <F4> key allows you to save any changes you have made and exit Setup. Press the <F4> key to save your changes. Esc The <Esc> key allows you to discard any changes you have made and exit the Setup. Press the <Esc> key to exit the setup without saving your changes. Enter The <Enter> key allows you to display or change the setup option listed for a particular setup item. The <Enter> key can also allow you to display the setup subscreens. AMI BIOS Setup Utility 37 GOT5100T-834 User’s Manual 3.2 Main Menu System Time/Date Use this option to change the system time and date. Highlight System Time or System Date using the <Arrow> keys. Enter new values through the keyboard. Press the <Tab> key or the <Arrow> keys to move between fields. The date must be entered in MM/DD/YY format. The time is entered in HH:MM:SS format. 38 AMI BIOS Setup Utility GOT5100T-834 User’s Manual 3.3 Advanced Menu The Advanced menu allows users to set configuration of the CPU and other system devices. You can select any of the items in the left frame of the screen to go to the sub menus: ACPI Settings NCT6106D Super IO Configuration NCT6106D H/W Monitor CPU Configuration IDE Configuration Intel TXE Configuration LPSS & SCC Configuration For items marked with “”, please press <Enter> for more options.’ ACPI Settings You can use this screen to select options for the ACPI Configuration, and change the value of the selected option. A description of the selected item appears on the right side of the screen. AMI BIOS Setup Utility 39 GOT5100T-834 User’s Manual ACPI Sleep State Allow you to select the Advanced Configuration and Power Interface (ACPI) state to be used for system suspend. Here are the options for your selection, Suspend disable and S3 (Suspend to RAM). 40 AMI BIOS Setup Utility GOT5100T-834 User’s Manual NCT6106D Super IO Configuration Use this screen to select options for the Super IO Configuration, and change the value of the selected option Serial Port 1-4 configuration Serial port: This option used to enable or disable the serial port. Device Setting: This item specifies the base I/O port address and Interrupt Request address of serial port. The port 0 Optimal setting is 3F8/IRQ4. The port 1 Optimal setting is 2F8/IRQ3. The port 2 Optimal setting is 3E8/IRQ7 The port 3 Optimal setting is 2E8/IRQ5. AMI BIOS Setup Utility 41 GOT5100T-834 User’s Manual Serial type This option used to select RS232/422/485 function. 42 AMI BIOS Setup Utility GOT5100T-834 User’s Manual NCT6106D H/W Monitor This screen shows the Hardware Health Configuration. AMI BIOS Setup Utility 43 GOT5100T-834 User’s Manual CPU Configuration This screen shows the CPU Configuration and Intel virtualization technology enable/disable selected 44 AMI BIOS Setup Utility GOT5100T-834 User’s Manual IDE Configuration You can use this screen to select options for the SATA Configuration, and change the value of the selected option. SATA Mode Use this item to choose the SATA operation mode. Here are the options for your selection, IDE Mode, AHCI Mode. AMI BIOS Setup Utility 45 GOT5100T-834 User’s Manual Intel TXE Configuration The Advanced menu allows users to update the TXE firmware. 46 AMI BIOS Setup Utility GOT5100T-834 User’s Manual LPSS & SCC Configuration You can select any of the items in the frame of the screen to change the OS, the default setting is Win 7. Please be informed to select the Windows 8.x when installing Win 8 or Win 8.1. If using the Android OS, please refer to https://01.org/android-ia. AMI BIOS Setup Utility 47 GOT5100T-834 User’s Manual 3.4 Chipset Menu The Chipset menu allows users to change the advanced chipset settings. 48 AMI BIOS Setup Utility GOT5100T-834 User’s Manual North Bridge This screen shows the North Bridge memory information. South Bridge AMI BIOS Setup Utility 49 GOT5100T-834 User’s Manual USB Configuration You can use this screen to select options for the USB Configuration, If USB3.0 function used, XHCI Mode must enable and EHCI must disable. **XHCI default is Auto. 50 AMI BIOS Setup Utility GOT5100T-834 User’s Manual 3.5 Security AMI BIOS Setup Utility 51 GOT5100T-834 User’s Manual 3.6 Boot Menu The Boot menu allows users to change boot options of the system. You can select any of the items in the left frame of the screen to go to the sub menus: Setup Prompt Timeout Set the Timeout for wait press key to enter Setup Menu. Bootup NumLock State Use this item to select the power-on state for the NumLock. The default setting is on. Quiet Boot Use this item to enable or disable the Quite Boot state. The default setting is disable. Legacy Pxe OPROM Use this item to enable or disable the reboot Execution Environment. The default setting is disable. Boot Option Priorities Specifies the overall boot order from the available devices. 52 AMI BIOS Setup Utility GOT5100T-834 User’s Manual 3.7 Save&Exit AMI BIOS Setup Utility 53 GOT5100T-834 User’s Manual This page is intentionally left blank. 54 AMI BIOS Setup Utility GOT5100T-834 User’s Manual Chapter 4 Drivers Installation 4.1 System GOT5100T-834 supports Windows 7, Windows 8/8.1 ,WES 7 and WE8S. To facilitate the installation of system driver, please carefully read the instructions in this chapter before start installing. 4.1.1 Win 7 1. Insert Driver CD and select the “\Drivers”. 2. Select all files and follow the installing procedure. NOTE Please install Microsoft KB2685811 before TXE installation under Windows 7, then installing the drivers. NOTE If graphic driver isn’t installed under Win7 or Win 8.x, only VGA function can be waked up when VGA and DP in hibernate mode. In order to solve this issue, user needs to re-start the computer or ensure the graphic driver is installed properly. Drivers Installation 55 GOT5100T-834 User’s Manual 4.1.2 Win 8/8.x 1. Insert Driver CD and select the “\Drivers”. 2. Select all files and follow the installing procedure. 4.2 Touch Screen The GOT5100T-834 uses the 5-wire analog resistive. There are the specification and driver installation which are listed below. 4.2.1 Specification Touch Screen 5-wire Analog Resistive type Touch Screen Controller PenMount 6000 USB Touch Screen Controller IC Communications USB interface Resolution 1024 x 1024 Power Input 5V Power Consumption Active: 24.6mA / Idle Mode: 13.4mA 56 Drivers Installation GOT5100T-834 User’s Manual 4.2.2 Driver Installation- Windows 7/8.x The GOT5100T-834 provides a touch screen driver that users can install it under the operating system Windows 7/8.x. To facilitate installation of the touch screen driver, you should read the instructions in this chapter carefully before you attempt installation. 1. Insert Driver CD and follow the path to select the “\Drivers\Step 7 - Touch”. 2. Follow the installing procedure and press OK. 3. Click Start menu and select “PenMount Utilities”; and then, a “PenMount Control Panel” pops out. Drivers Installation 57 GOT5100T-834 User’s Manual 4. Select the “Standard Calibrate” tab. 5. Calibration: To adjust the display with touch panel, click “Calibration” and follow the calibrate point to do calibration; there are five points on screen for calibration. 6. 58 Press OK. Drivers Installation GOT5100T-834 User’s Manual 4.3 Embedded O.S. The GOT5100T-834 provides the WES 7 and WE8S Embedded. The O.S. is supported devices which are listed below. 4.3.1 WES 7 & WE8S Here are supported onboard devices: Onboard Multi I/O SATA HDD USB CRT/LCD display 10/100/1000 base-T Ethernet TM CFast or mSATA Onboard Audio Touch Screen PenMount Touch screen Before you can use and calibrate it, here is what you should do: 1. Set up Penmount touch device driver by executing C:\Penmount\ Windows 2000-XP V5.0\setup.exe. When the installation is finished, an icon “PM” appears on the Taskbar. 2. Calibrate Penmount touch by clicking on the “PM” icon, and the go on the calibration. 3. Restart the computer. Drivers Installation 59 GOT5100T-834 User’s Manual This page is intentionally left blank. 60 Drivers Installation GOT5100T-834 User’s Manual Appendix A Watchdog Timer About Watchdog Timer Software stability is major issue in most application. Some embedded systems are not watched by human for 24 hours. It is usually too slow to wait for someone to reboot when computer hangs. The systems need to be able to reset automatically when things go wrong. The watchdog timer gives us solution. The watchdog timer is a counter that triggers a system reset when it counts down to zero from a preset value. The software starts counter with an initial value and must reset it periodically. If the counter ever reaches zero which means the software has crashed, the system will reboot. How to Use Watchdog Timer The I/O port base addresses of watchdog timer are 2E (hex) and 2F (hex). The 2E (hex) and 2F (hex) are address and data port respectively. Assume that program A is put in a loop that must execute at least once every 10ms. Initialize watchdog timer with a value bigger than 10ms. If the software has no problems; watchdog timer will never expire because software will always restart the counter before it reaches zero. Begin Next Enable and Initialize Watchdog Timer Next Program “A” Next Disable Watchdog Timer Next Watchdog Timer Begin Next Enable and Initialize Watchdog Timer Next Program “A” Next Reset Watchdog Timer Next 61 GOT5100T-834 User’s Manual WDT Sample Program Enable WDT 1.Enable configuration -O 2E 87 -O 2E 87 2. Select Logic device: -O 2E 07 -O 2F 08 3. WDT Device Enable -O 2E 30 -O 2F 01 4. Set timer unit -O 2E F0 -O 2F 00 (00: Sec; 08: Minute) 5. Set base timer: -O 2E F1 -O 2F 0A Set Reset Time (Ex.0A:10 Sec) Disable WDT 1.Enable configuration -O 2E 87 -O 2E 87 2. Select Logic device: -O 2E 07 -O 2F 08 3. WDT Device Disable -O 2E 30 -O 2F 00 Digital I/O Software Programming I2C to GPIO PCA9535PW GPIO I2C address: 0b01000000. 62 Watchdog Timer GOT5100T-834 User’s Manual Watchdog Timer 63 GOT5100T-834 User’s Manual 64 Watchdog Timer GOT5100T-834 User’s Manual Appendix B Backlight Control About Backlight Control Axiomtek offers the backlight control tool under Windows 7 and Windows 8, people can adjust the panel backlight depending on your personal taste and the amount of ambient light in the room after installing the backlight control tool. How to Use Backlight Control Step 1 According to the OS version, please insert the driver CD and follow the path to select the proper driver, “\Driver\Win8.x\Step 8 – BrightnessSync” or \Driver\Win7\Step 8 - BrightnessSync”. Backlight Control 65 GOT5100T-834 User’s Manual 66 Backlight Control GOT5100T-834 User’s Manual Step 2 Follow the installing procedures and press “Close”. Backlight Control 67 GOT5100T-834 User’s Manual 68 Backlight Control GOT5100T-834 User’s Manual Backlight Control 69 GOT5100T-834 User’s Manual 70 Backlight Control GOT5100T-834 User’s Manual Backlight Control 71 GOT5100T-834 User’s Manual Step 3 System auto reboot, installation completed. Step 4 Select “△” icon then find out the “Axiomtek” to ensure the brightness driver is installed appropriately. Step 5 How to use the brightness Control There are two ways to adjust the display brightness. Step 5.1 72 Click the “Brightness” to adjust the display brightness with the bar. (For Windows 8.x only.) Backlight Control GOT5100T-834 User’s Manual Step 5.2. Click the “Control Panel” then select “Power Options” to adjust the display brightness. Backlight Control 73 GOT5100T-834 User’s Manual Removed Brightness Control Tool Step 1 74 According to the OS version, please insert the driver CD and follow the path to select the proper driver, “\Driver\Win8.x\Step 8 – Setup” or \Driver\Win7\Step 8 - Setup”. Backlight Control GOT5100T-834 User’s Manual Step 2 Follow the procedures and press “Close”. Backlight Control 75 GOT5100T-834 User’s Manual 76 Backlight Control GOT5100T-834 User’s Manual Step 3 System auto reboot, uninstallation completed. Backlight Control 77 GOT5100T-834 User’s Manual This page is intentionally left blank. 78 Backlight Control