HC7 Series HIGH CURRENT 7 Power Inductors Description RoHS 2002/95/EC • 155°C maximum total temperature operation • Surface mount inductors designed for higher speed switch mode applications requiring lower inductance, low voltage and high current • Design utilizes high temperature powder iron material with a non-organic binder to eliminate thermal aging • Inductance range from 0.22 uH to 4.81 uH • Current range from 35.8 to 9.8 Amps • Frequency range 1kHz to 500kHz Applications • Next generation microprocessors • High current DC-DC converters • VRM, multi-phase buck regulator • PC, Workstations, Routers • Telecom soft switches, Base Stations Environmental Data • Storage temperature range: -40°C to +155°C • Operating ambient temperature range: -40°C to +155°C (range is application specific) • Solder reflow temperature: +260°C max. for 10 seconds max. Part Number HC7-R20-R HC7-R47-R HC7-1R0-R HC7-1R5-R HC7-2R2-R HC7-3R9-R HC7-4R7-R Rated Inductance µH .20 .47 1.0 1.5 2.2 3.9 4.7 OCL (1) nominal +/-20% µH 0.220 0.534 1.05 1.73 2.58 3.61 4.81 Irms (2) Amperes (Typ.) 35.80 23.40 20.30 14.20 13.00 10.40 9.80 Isat (3) Amperes 15% rolloff 45.8 27.5 19.6 15.3 12.5 10.6 9.2 1) Test Parameters: 100KHz, 1.0Vrms 2) Irms Amperes for approximately ∆T of 40°C above 85°C ambient 3) Isat Amperes Peak for approximately 15% rolloff (@20°C) 4) Isat Amperes Peak for approximately 30% rolloff (@20°C) 5) Applied Volt-Time product (V-µS) across the inductor. This value represents the applied V-µS at operating frequency necessary to generate additional core loss which contributes to the 40°C temperature rise. De-rating of the Irms is required to prevent excessive temperature rise. The 100% V-uS rating is equivalent to a ripple current Ip-p of 20% of Isat (30% rolloff option). It is recommended that the temperature of the part not exceed 155°C under worst case operating conditions verified in the end application. Mechanical Diagrams C DCR (mΩ) max. @ 20°C 0.67 1.60 2.10 4.30 5.20 7.90 9.00 Volts (5) µSec (VµS) 2.27 3.83 5.36 6.90 8.40 10.0 12.6 Units supplied in tape and reel packaging. 13" reels 610 parts per reel. Carrier tape width = 24 mm. Meets EIA standard Part number definition: HC7-XXX-R HC7 = Product code and size XXX = Inductance value in uH. R = Decimal point. If no R is present, third character = #of zeros -R suffix indicates RoHS compliant SIDE VIEW L Height Max Length Max 3.0 ± 0.25 (2x) 2.60 max 5.10 ±0.40 13.0 Max RECOMMENDED PCB PAD LAYOUT 3.50 typ 2plcs SCHEMATIC 1 3.50 typ 2plcs 6.50 typ wwllyy = Date code R = Revision level Isat (4) Amperes 30% rolloff 86.5 51.9 37.1 28.8 23.6 20.0 17.3 FRONT VIEW TOP VIEW HC7-XXX wwllyy R Packaging • Supplied in tape and reel packaging, 610 parts per reel 2 Maximum Dimension Part Number HC7-R20-R HC7-R47-R HC7-1R0-R HC7-1R5-R HC7-2R2-R HC7-3R9-R HC7-4R7-R Height mm 6.0 5.5 5.5 5.5 5.5 5.5 5.5 Length mm 14.25 13.8 13.8 13.8 13.8 13.8 13.8 Dimensions in Millimeters. All dimensions I+/- 0.2 mm unless otherwise specified. All soldering surfaces are coplanar within 0.15 mm. HC7 Series HIGH CURRENT 7 Power Inductors 4.0 Packaging Information 1.5 dia +0.1/-0.0 2.0 1.5 dia min A 1.75 1 A0= 13.00 mm A1= 4.00 mm 11.5 B0= 13.00 mm B1= 14.10 mm B0 B1 24.0 +/-0.3 HC7-XX X wwllyy R K0= 5.6 mm K1= 6.0 mm 2 K0 16.00 K1 A1 A SECTION A-A A0 User direction of feed Dimensions in Millimeters Core Loss Irms DERATING WITH CORE LOSS % of Applied Volt-u-Seconds 20 30 40 50 60 70 80 90 100 110 120 130 140 150 160 170 180 190 200 10 20 (maximum) % of Irms specified from zero ripple application 10 0 100kHz 200kHz 300kHz 400kHz 500kHz 30 40 50 60 70 80 90 100 Inductance Characteristics Inductance vs. Idc 5 4.5 4 HC7-R20 3.5 HC7-R47 3 HC7-1R0 L 2.5 (uH) 2 HC7-1R5 HC7-2R2 HC7-3R9 1.5 HC7-4R7 1 0.5 0 0 6 12 18 24 30 36 42 48 54 60 66 72 78 84 DC CURRENT (A) PM-4116 3/07 © Cooper Electronic Technologies 2007 Visit us on the Web at www.cooperbussmann.com 1225 Broken Sound Pkwy. Suite F Boca Raton, FL 33487 Tel: +1-561-998-4100 Toll Free: +1-888-414-2645 Fax: +1-561-241-6640 This bulletin is intended to present product design solutions and technical information that will help the end user with design applications. Cooper Electronic Technologies reserves the right, without notice, to change design or construction of any products and to discontinue or limit distribution of any products. Cooper Electronic Technologies also reserves the right to change or update, without notice, any technical information contained in this bulletin. Once a product has been selected, it should be tested by the user in all possible applications. Life Support Policy: Cooper Electronic Technologies does not authorize the use of any of its products for use in life support devices or systems without the express written approval of an officer of the Company. Life support systems are devices which support or sustain life, and whose failure to perform, when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in significant injury to the user.