MAGNUM ® Euro-MAG Series PCB – Spring Clamp Single & Double Row Filtered Connectors Series A2000, LP2000 & CB2000 Single Row Terminal Blocks A20510807WR SPECIFICATIONS Rating: A2: 30A, 300V* LP2: 30A, 150V* CB2: 30A, 300V* Center Spacing: .375” or 3/8” (9.52 mm) LP202110 Wire Range: #12-22 AWG CU Screw Size: #6-32 zinc plated philslot Torque Rating: 9 in-lb. Base: Standoffs standard for easy flux washing Distance Between Barriers: .32” (8.1 mm) Recommended PCB Hole Diameter: .076” (1.93 mm) Operating Temperature: 105°C (221°F) max., -40°C (-40°F) min. Molded Material: Black, UL Rated 94V0 Thermoplastic Breakdown Voltage: 3400V (A2 & LP2); 4100V (CB2). Agency Information: UL/CSA; IEC Compliance; CE Certified *30A Rating achieved with a #10 copper wire crimped to a ring terminal.; 20A Rating without ring terminal. Poles MOUNTING ENDS ONLY A C Mount Ctrs. Length BARRIER & MOUNTING ENDS B Pole Ctrs. BARRIER ENDS ONLY C Length CB20210507 A2000 & LP2000 Series .375 (9.53) .15 (3.8) dia. .65 (16.5) C Mount End WIRE MANAGEMENT PRODUCTS Power Distribution Blocks Base & Rail Mount Connectors 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 1.13 1.50 1.88 2.25 2.63 3.00 3.38 3.75 4.13 4.50 4.88 5.25 5.63 6.00 6.38 6.75 7.13 7.50 7.88 8.25 8.63 9.00 9.38 9.75 10.13 10.50 10.88 11.25 11.63 1.56 1.93 2.30 2.68 3.06 3.43 3.81 4.18 4.56 4.93 5.31 5.69 6.06 6.43 6.81 7.18 7.56 7.93 8.31 8.68 9.06 9.43 9.81 10.18 10.56 10.93 11.31 11.68 12.05 .38 .75 1.13 1.50 1.88 2.25 2.63 3.00 3.38 3.75 4.13 4.50 4.88 5.25 5.63 6.00 6.38 6.75 7.13 7.50 7.88 8.25 8.63 9.00 9.38 9.75 10.13 10.50 10.88 11.25 11.63 .81 1.18 1.56 1.93 2.31 2.68 3.06 3.43 3.81 4.18 4.56 4.93 5.31 5.68 6.06 6.43 6.81 7.18 7.56 7.93 8.31 8.68 9.06 9.43 9.81 10.18 10.55 10.93 11.31 11.68 12.05 Barrier End .76 (19.3) .565 (14.35) on LP2000 .40 (10.2) .02 (.5) A Mount Centers B Pole Centers Mount End Barrier End CB2000 Series .375 (9.53) .19 (4.8) dia. .70 (17.8) .32 (8.1) C Mount End Barrier End .60 (15.2) * Dimensions in inches. To convert to millimeters, multiply by 25.4. .02 (.5) A Mount Centers B Pole Centers Mount End 6 Barrier End Series A2000 & LP2000 Single Row Terminal Blocks Single & Double Row Filtered Connectors Part Numbering System Series Terminal Style Base/End Poles Screw Options Options A 2 L P 2 0 - flat base/molded 02 to 32 mount end 02 to 30 on mount 1 - flat base/mnt. end end base 2 - flat base/barrier end 3 - insulator base/mnt. end 4 - insulator base/ barrier end 5 - closed base/ mount end 6 - closed base/ molded mount end 9 - insulator base/ molded mount end Base/End Note: 0, 6, 9 styles not available with covers. 5 & 6 Styles only available with 03 terminals. Blank - std. screw AB - angle mnt. options (pg 9) 00 - screws shipped bulk A1 to A9 - .250” QC 03 stainless steel B1 to B9 - .187” QC 04 - brass nickel plated DR - drilled right angle (pg 9) 07 steel SEMS JA, JB & JC - barrier jumpers (not available L1 to L6 marking options (pg 22) with hardware options) MP, MP8 & MT mounting plates (pg 9) 09 - brass SEMS OJ2 & OJ4 - over barrier jumpers (not nickel plated available w/covers) (not available with RC - retaining clips (pg 9) hardware options) R30 to R77 - right angle bends (pg 9) CA captive screw SO - stand off insulators (pg 9) 03CA stainless steel captive S1 - solder lug/flat 04CA - brass captive 07CA SEMS captive Covers - (pg 23) 09CA brass SEMS captive 07WR steel SEMS wire ready (not available on LP2) 031 .79) Inches (Millimeters) .20 (5.1) .55 (14.0) .55 (14.0) .031 (.79) .062 (1.57) 01 Handwired 02 Printed Circuit 03 Non Feed-Thru .031 (.79) 05 Extended Handwired .11 (2.79) .17 (4.3) .031 (.79) .031 (.79) .062 (1.57) .062 (1.57 ) 08 Printed Circuit 07 Extended Pin 06 Handwired .42 (10.7) .250 (6.35) .031 (.79) 09 .250 QC short .72 (18.3) .031 (.79) .31 (7.9) .187 (4.75) 10 .187 QC .41 (10.4) .031 (.79) .125 (3.2) 14 Printed Circuit .062 (1.57) .031 (.79) .250 (6.35) 19 .250 QC long 7 WIRE MANAGEMENT PRODUCTS .33 (8.4) .40 (10.2) Power Distribution Blocks .110 (2.79) 04 Wire Wrap Tail .82 (20.8) .30 (7.6) .66 (16.8) .062 (1.57) .031 (.79) .110 (2.79) .031 (.79) Base & Rail Mount Connectors Terminal Styles Euro-MAG Series PCB – Spring Clamp A2 - standard barrier 01 - handwired LP2 - low profile 02 - printed circuit barrier 03 - non feed-thru 04 - wire wrap tail 05 - extended handwired 06 - handwired 07 - extended pin 08 - printed circuit 09 - .250 QC short 10 - .187 QC 14 - printed circuit 19 - .250 QC long MAGNUM ® Single & Double Row Filtered Connectors Series A2000 & LP2000 Single Row Terminal Blocks Continued Screw Options Standard Zinc Plated Steel Hardware Options Euro-MAG Series PCB – Spring Clamp 04 Brass Nickel Plated 03 Stainless Steel 09 Brass SEMS Nickel Plated 07WR Wire Ready (A2 only) Inches (Millimeters) (Bulk ordering part numbers are in parentheses.) Jumpers Solder Lugs 07 Steel SEMS Quick Connects Blade Width A = .250” Blade Width B = .187” .68 (17.3) .33 (8.4) .84 (21.2) S1 (2S1) JA (JA2-XX) OJ2 A1 & B1 (2A1 & 2B1) A2 & B2 (2A2 & 2B2) A3 & B3 (2A3 & 2B3) OJ4 A4 & B4 (2A4 & 2B4) A5 & B5 (2A5 & 2B5) A6 & B6 (2A6 & 2B6) A7 & B7 (2A7 & 2B7) A8 & B8 (2A8 & 2B8) A9 & B9 (2A9 & 2B9) Base & Rail Mount Connectors .33 (8.4) JB (JB2-XX) .33 (8.4) JC (JC2-XX) Power Distribution Blocks Base/End Options B B B .180 (4.57) .150 dia. (3.8) mounting holes (2) .218 (5.54) WIRE MANAGEMENT PRODUCTS .40 (10.2) .40 10.2) .095 (2.4) SECTION A–A 0, 6 & 9 Molded Mount End 8 SECTION B–B 1, 3 & 5 Mount End B Series A2000 & LP2000 Single Row Terminal Blocks Continued Single & Double Row Filtered Connectors Mounting Options Right Angle Bends (A2, LP2 only) Right angle terminals are offered on the A2000 & LP2000 Series. Configurations are defined in these dimensions: X = pin extension beyond the block base; Z = length from block base to centerline of the terminal tip. Standard bends consist of the X and Z dimensions shown in the chart. Specify by adding the selected Bend Option Code to the terminal part no. 07 Terminal Bend Configurations Z 04 Terminal Bend Configurations .82 X .55 Bend Option Code Bend Option Code X Available w/insulator base Available w/insulator base -.04 .01 .02 .05 .08 .12 .14 .16 .28 .23 .22 .19 .16 .12 .10 .08 No No No No No No No No R30 R35 R36 R42 R46 R50 R53 R66 R69 R75 R77 -.04 .01 .02 .08 .12 .16 .19 .32 .35 .41 .43 .55 .50 .49 .43 .39 .35 .32 .19 .16 .10 .08 Yes Yes Yes Yes Yes No No No No No No Dimensions in inches. To convert to millimeters, multiply by 25.4. Angle Brackets (A2, LP2 only) Drilled Right Angle (A2, LP2 only) Base & Rail Mount Connectors Z ; ;; ; ; ;; Z X (minimum) R30 R35 R36 R39 R42 R46 R48 R50 X (minimum) Euro-MAG Series PCB – Spring Clamp Z .24 .375 .25 .04 .45 .144 HOLE w/.312 C' BORE Option AB Angle brackets enable block to be fastened at right angles to normal mount position. Bulk part no. 2AB. Mounting Plates MOUNTING PLATE Option DR Counterbored holes across mount ends of block enable fastening with two screws at right angles to normal mount position. Standoffs Retaining Clip Power Distribution Blocks .32 .15 MP MP8 RETAINING CLIP STANDOFF Options MP, MP8 & MT MP Metal inserts with .150” dia. hole accept #6 screw. MP8 Metal inserts with .187” dia. hole accept #8-32 screw. MT Metal inserts with tapped hole accept #6-32 screw. Option SO Standoff mounts are tubes molded to the mounting positions. Available with insulator bases only. Option RC Use on standoff tubes. Fit panels up to .125” thick. Two clips for every five positions. Supplied unassembled. Bulk Part No. H541. 9 WIRE MANAGEMENT PRODUCTS .300 MT MAGNUM ® Single & Double Row Filtered Connectors Series CB2000 Single Row Terminal Blocks Part Numbering System Series Terminal Style Base/End Poles Screws Options 01 02 03 07 14 22 1 - mount end 2 - barrier end 02 to 32 02 to 30 on mount end base 03 stainless steel 04 brass nickel plated 07 steel SEMS standard 09 - brass SEMS nickel plated CA captive screw 07CA SEMS captive AB - angle mounting brackets (pg 11) A7 to A9 - .250” QC B7 to B9 - .187” QC EB - exit back terminals EF - exit front terminals JA, JB & JC - barrier jumpers L1 to L6 marking options (pg 22) LT1 to LT6 marking options (pg 22) OJ2 & OJ4 - over barrier jumpers MP, MP8, MT & MT8 mtg. plates (pg 11) S1 - solder lug/flat Covers - (pg.23) C B 2 Euro-MAG Series PCB – Spring Clamp CB2 - closed back - handwired - printed circuit - non feed-thru - extended pin - printed circuit - dual tail printed circuit Terminal Styles Inches (Millimeters) .19 (4.9) Base & Rail Mount Connectors .81 (4.6) .19 (4.8 ) .40 (10.2) .0 (.7 .120 (3.05) .045 (1.14) .18 (4.6) .70 (17.8) .0 (. .062 (1.57) .18 (4.6) 01 Handwired 02 Printed Circuit .125 (3.18) 03 Non Feed-Thru Available on Mount End (1) only. .045 (1.14) .18 (4.6) .0 (. .18 (4.6) 14 Printed Circuit 07 Extended Pin .045 (1.14) .0 (.7 .03 (.79) .40 (10.2) .43 (10.9) 22 Dual Tail Printred Circuit Power Distribution Blocks Screw Options 03 Stainless Steel 04 Brass Nickel Plated 07 Steel SEMS Zinc Plated 09 Brass SEMS Nickel Plated * NOTE: Wire ready screws standard on all terminal styles. CB2 Terminal Exit Options Inches (Millimeters) WIRE MANAGEMENT PRODUCTS Y .255 (6.48) .18 (4.6) Exit Rear (std.) 10 X .18 (4.6) EF Exit Front X EB Exit Back Series CB2000 Single Row Terminal Blocks Solder Lugs Inches (Millimeters) (Bulk ordering part numbers are in parentheses.) Jumpers Single & Double Row Filtered Connectors Hardware Options Quick Connects Blade Width A = .250”. Blade Width B = .187”. .68 (17.3) .33 (8.4) .84 (21.2) S1 (2S1) OJ2 JA (JA2-XX) A7 & B7 (2A7 & 2B7) A8 & B8 (2A8 & 2B8) A9 & B9 (2A9 & 2B9) JB (JB2-XX) OJ4 .33 (8.4) JC (JC2-XX) ; ; Inches (Millimeters) Right Angle Mounting Bracket .71 (18.0) Snap-in Angle Bracket End Positions usable Chassis or PCB A #6 or #8 mounting screw & nut (Customer supplied.) .79 (20.1) 1.02 (25.8) Exit Back (EB) Terminals .24 (6.1) Mounts blocks on PC boards at a right angle. • Protects solder joints. • Recommended for all EB (Exit Back) PCB terminal blocks. • Bracket snaps securely on block (no hardware required). • Minimum strip length (end positions are usable). • Mount with #6-32 or #8-32 screws (not supplied). MOUNTING PLATE A .42 (10.7) Option AB Options MP, MP8, MT & MT8 MP Metal inserts with .150” dia. hole accept #6 screw. MP8 Metal inserts with .187” dia. hole accept #8-32 screw. MT Metal inserts with tapped hole accept #6-32 screw. MT8 Metal inserts with tapped hole accept #8-32 screw. MT MT8 11 WIRE MANAGEMENT PRODUCTS ; MP MP8 .45 (11.4) Power Distribution Blocks Angle Bracket Mounting Plates Base & Rail Mount Connectors Mounting Options Euro-MAG Series PCB – Spring Clamp .33 (8.4)