AZ2800 30 AMP MINIATURE POWER RELAY FEATURES • • • • • • DPST-NO and DPDT configuration Meets 8 mm creepage, 4 kV dielectric Epoxy sealed versions available UL Class F (155°C) standard UL, CUR file E44211 VDE certificate 40023442 CONTACTS Arrangement DPST (2 Form A) DPDT (2 Form C) Ratings Resistive load: Max. switched power: 560 W or 8310 VA Max. switched current: 30 A (N.O), 3 A (N.C.) Max. switched voltage: 30 VDC* or 600 VAC *Note: If switching voltage is greater than 30VDC, special precautions must be taken. Please contact the factory. Rated Load UL Normally open contacts (N.O.) 30 A at 277 VAC General Use, 100k cycles [1][2] 10 A at 600 VAC, General Use, 6k cycles [1] 1 HP at 120 VAC, 100k cycles [1][2] 2.5 HP at 240 VAC, 100k cycles [1][2] 8 FLA / 26 LRA at 277, 480, 600 VAC, 30k cycles [1] Normally open contacts (N.O.), DC Coils only 25.3 FLA / 110 LRA at 240 VAC, 30k cycles [1][2] Normally closed contacts (N.C.) 3 A at 277 VAC, General Use, 100k cycles [1][2] 2 A at 480 VAC, General Use, 6k cycles [1] 1 A at 600 VAC, General Use, 6k cycles [1] 3 FLA / 3 LRA at 240 VAC, 30k cycles [1] 2 FLA / 2 LRA at 277, 480 VAC, 30k cycles [1] 1 FLA / 1 LRA at 600 VAC, 30k cycles [1] VDE Normally open contacts (N.O.) 20 A at 250 VAC, Resistive, 50k cycles [2] Normally closed contacts (N.C.) 3 A at 250 VAC, Resistive, 50k cycles [2] Material Resistance GENERAL DATA Life Expectancy Mechanical Electrical Minimum operations 5 x 107 1 x 105 at 30 A 277 VAC Res. (N.O.) Operate Time 15 ms typical 25 ms maximum with bounce Release Time 10 ms typical 25 ms maximum with bounce (with no coil suppression) Dielectric Strength 1500 Vrms contact to contact (at sea level for 1 min.) 4000 Vrms contact to coil 2000 Vrms between contact sets Insulation Resistance 109 ohms minimum at 500 VDC Dropout DC: Greater than 10% of nominal coil voltage AC: Greater than 20% of nominal coil voltage Ambient Temperature Operating At nominal coil voltage DC: -40°C (-40°F) to 85°C (185°F) AC: -40°C (-40°F) to 65°C (149°F) -40°C (-40°F) to 105°C (221°F) Storage Vibration 0.062" (1.5 mm) DA at 10–55 Hz Shock Operational, 10 g for 11 ms 1/2 sine pulse (no contact opening > 100usec) Non-destructive, 100 g for 11 ms 1/2 sine pulse Enclosure P.B.T. polyester Terminals Quick connect tabs Note: Allow suitable slack on leads when wiring, and do not subject the terminals to excessive force. Silver cadmium [1], silver tin oxide [2] <50 milliohms initially (6 V, 1 A voltage drop method) COIL Power Max. Solvent Temp. 80°C (176°F) Max. Immersion Time 30 seconds Weight 86 grams Packing unit in pcs 20 per plastic tray / 100 per carton box At Pickup Voltage (typical) 925 mW, DC coil 2.6 VA, AC coil Max. Continuous Dissipation 5.0 W at 20°C (68°F) ambient, DC coil 7.0 VA at 20°C (68°F) ambient, AC coil Temperature Rise 48°C (86°F) at nominal coil voltage, DC coil 68° C (122°F) at nominal coil voltage, AC coil 1. All values at 20°C (68°F). Max. 155°C (311°F) 3. Specifications subject to change without notice. Temperature NOTES 2. Relay may pull in with less than “Must Operate” value. 3/12/15 AZ2800 RELAY ORDERING DATA COIL SPECIFICATIONS – DC Coil Nominal Coil VDC 6 Coil Resistance Ohm ± 10% 22 ORDER NUMBER* 140.0 86 AZ2800–2C–12D 68.5 350 AZ2800–2C–24D 83.4 34.5 1390 AZ2800–2C–48D 190.5 15.2 7255 AZ2800–2C–110D Max. Continuous VAC 15.6 Nominal Current mA ± 10% 340.0 Must Operate VDC 4.5 Max. Continuous VDC 10.5 12 9.0 20.7 24 18.0 41.8 48 36.0 110 82.5 Nominal Current mA ± 10% 272.0 AZ2800–2C–6D COIL SPECIFICATIONS – AC Coil Nominal Coil VAC 12 Must Operate VAC 9.6 50Hz Coil Resistance 60Hz Coil Resistance ORDER NUMBER* Ohm ± 10% Ohm ± 10% 9.5 8 AZ2800–2C–12A 24 19.2 31.2 166.0 45 35.7 AZ2800–2C–24A 120 96.0 156.0 33.3 1125 830 AZ2800–2C–120A 220 176.0 286.0 18.2 3800 2870 AZ2800–2C–220A 240 192.0 312.0 16.7 4500 3800 AZ2800–2C–240A 277 221.6 360.1 14.4 5960 4700 AZ2800–2C–277A * Substitute “2A” in place of “2C” to indicate 2 Form A contacts. “2A” or “2C” denotes silver cadmium contacts. Add suffix “E” to “2A” or “2C” for silver tin oxide contacts. Add suffix “5” for 50 Hz coil, AC coils only. (Example: AZ2800-2C-24A5) Add suffix “E” at the end of order number for sealed version. Add suffix “K” for 0.187” x 0.020” [4.8 mm x 0.5 mm] coil terminals. MECHANICAL DATA .31 [8.0] .58 [14.8] WIRING DIAGRAM .18 [4.6] .63 [16.0] 1.36 Max. [34.5] 1.00 [25.4] .15 [3.8] 6 x.250 [6.35] 1.62 [41.1] 2.35 [59.7] 8 x.032 [.81] 0 2 4 3 6 8 7 1 1.04 [26.4] 2 FORM C 2 x DIM "A" DIM. "A" = .250 [6.35] x .032 [.81] THK - STANDARD 0 DIM. "A" = .187 [4.75] x .020 [.51] THK - "K" SUFFIX 8 x.45 [11.4] 2 4 6 8 .13 [3.3] 1 2 FORM A 2.69 [68.4] VIEWED TOWARD TERMINALS Dimensions in inches with metric equivalents in parentheses. Tolerance: ± .010" 3/12/15