AZ697 10 AMP MINIATURE POWER RELAY FEATURES • • • • • • • • Dielectric strength 5000 Vrms Low cost Epoxy sealed version available 10 Amp switching — single pole contacts UL TV-5 Isolation spacing greater than 8mm UL Class B insulation system, Class F available UL, CUR file E44211; TÜV file R50129288 CONTACTS Arrangement SPST (1 Form A) SPDT (1 Form C) Ratings Resistive load: Max. switched power: 300 W or 2770 VA Max. switched current: 10 A Max. switched voltage: 150* VDC or 380 VAC *Note: If switching voltage is greater than 30 VDC, special GENERAL DATA Life Expectancy Mechanical Electrical Minimum operations 1 x 107 1 x 105 at 10 A 240 VAC Res. Operate Time (typical) 8 ms at nominal coil voltage Release Time (typical) 5 ms at nominal coil voltage (with no coil suppression) precautions must be taken. Please contact the factory. Rated Load UL, CUR TV-5 at 120 VAC [1][2][3] 10 A at 277 VAC, General Use [1] 10 A 30 VDC, Resistive [1] 1/3 HP at 250 VAC [1] 1/4 HP at 125 VAC N.O. [1] 10 A at 277 VAC, General Use, 100k cycles [2][3] 10 A at 30 VDC, Resistive, 100k cycles [2][3] 1/3 HP at 250 VAC, 100k cycles [2][3] 1/4 HP at 125 VAC, 100k cycles [2][3] TÜV 10 A at 250 VAC, 30 VDC Resistive 100k cycles [1][2] 10 A at 250 VAC, 30 VDC Resistive 50k cycles [3] Material Silver cadmium oxide [1], silver nickel [2], silver tin oxide [3], Gold plating available Resistance < 50 milliohms initially (24 V, 1 A voltage drop method) COIL Power At Pickup Voltage (typical) 257 mW Max. Continuous Dissipation Temperature Rise 1.9 W at 20°C (68°F) ambient (Class B) 2.5 W at 20°C (68°F) ambient (Class F) Temperature 34° C (61°F) at nominal voltage Max. 130°C (266°F) Class B Max. 155° C (311° F) Class F Dielectric Strength 5000 Vrms coil to contact (at sea level for 1 min.) 1000 Vrms between open contacts Insulation Resistance 1000 megohms min. at 20°C, 500 VDC 50% RH Dropout Greater than 10% of nominal coil voltage Ambient Temperature Operating Storage At nominal coil voltage -40°C (-40°F) to 90°C (194°F) Class B -40°C (-40°F) to 110°C (230°F) Class F -40°C (-40°F) to 130°C (266°F) Class B -40°C (-40°F) to 155°C (311°F) Class F Vibration 0.062" DA at 10–55 Hz Shock 10 g Enclosure P.B.T. polyester Terminals Tinned copper alloy, P. C. Max. Solder Temp. 270°C (518°F) Max. Solder Time 5 seconds Max. Solvent Temp. 80°C (176°F) Max. Immersion Time 30 seconds Weight 18 grams NOTES 1. All values at 20°C (68°F). 2. Relay may pull in with less than “Must Operate” value. 3. Specifications subject to change without notice. 1/15/13 AZ697 RELAY ORDERING DATA COIL SPECIFICATIONS Nominal Coil VDC Must Operate VDC Max. Continuous VDC 3 5 6 9 12 18 24 48 60 110 2.1 3.5 4.2 6.3 8.4 12.6 16.8 33.6 42.0 79.3 5.7 9.4 11.4 17.4 22.8 27.9 45.7 89.0 115.3 170.5 ORDER NUMBER* Coil Resistance 17 47 68 160 275 650 1100 4170 7000 22900 ±10% ±10% ±10% ±10% ±10% ±10% ±15% ±15% ±15% ±15% Form A (SPST) Form C (SPDT) AZ697–1A–3D AZ697–1A–5D AZ697–1A–6D AZ697–1A–9D AZ697–1A–12D AZ697–1A–18D AZ697–1A–24D AZ697–1A–48D AZ697–1A–60D AZ697–1A–110D AZ697–1C–3D AZ697–1C–5D AZ697–1C–6D AZ697–1C–9D AZ697–1C–12D AZ697–1C–18D AZ697–1C–24D AZ697–1C–48D AZ697–1C–60D AZ697–1C–110D *For silver nickel contacts change “-1A” or “-1C” to “-1AB” or “-1CB”. For silver tin oxide contacts change “-1A” or “-1C” to “-1AE” or “-1CE”. For epoxy seal change “D” to “DE”. For gold plating change “D” or “DE” to “DA” or “DEA”. For Class F insulation add suffix “F” to part number. When suffix “E” is specified for Epoxy Seal, refer to AZ “Relay Technical Notes” on AZ website - Product Resources. Consult factory for other PCB process conditions that may apply. HARDWARE ORDERING DATA DESCRIPTION ORDER NUMBER DESCRIPTION ORDER NUMBER Socket ST482–U1 Retainer ST482–2 MECHANICAL DATA HARDWARE ST482-2 Dimensions in inches with metric equivalents in parentheses. Tolerance: ± .010" 1/15/13