10 AMP SUBMINIATURE POWER RELAY

AZ696
10 AMP SUBMINIATURE
POWER RELAY
FEATURES
• Miniature size: Form A version: 0.63" (16 mm) height,
1.10" (30 mm) length, 0.39" (10 mm) width
• High sensitivity, 100 mW pickup
• Dielectric strength 4000 Vrms
• Isolation spacing greater than 8 mm
• Approvals/Standards include: UL, VDE, IEC
• 10 Amp switching capability
• Epoxy sealed for automatic wave soldering and cleaning
• UL, CUR file E43203
CONTACTS
GENERAL DATA
Arrangement
SPDT (1 Form C)
SPST (1 Form A)
Ratings
Resistive load:
SPST (1 Form B)
Max. switched power: 300 W or 2500 VA
Max. switched current: 10 A
Max. switched voltage: 150* VDC or 380 VAC
UL Rating: 10 A at 30 VDC resistive
10 A at 250 VAC general use
1/4 HP 120 VAC
1/2 HP 250 VAC
B 300 pilot duty
*Note: If switching voltage is greater than 30 VDC, special
precautions must be taken. Please contact the factory.
Material
Silver cadmium oxide or silver tin oxide
Resistance
< 30 milliohms initially
(at rated current, voltage drop method)
COIL
Power
At Pickup Voltage
(typical)
100 mW
Max. Continuous
Dissipation
1.5 W at 20°C (68°F) ambient
1.2 W at 40°C (104°F) ambient
Temperature Rise
20°C (36°F) at nominal coil voltage
Temperature
Max. 110°C (230°F)
NOTES
Life Expectancy
Mechanical
Electrical
Minimum operations
10 million
1 X 105 at 10 A 240 VAC Res.
Operate Time (typical)
10 ms at nominal coil voltage
Release Time (typical)
5 ms at nominal coil voltage
(with no coil suppression)
Dielectric Strength
4000 Vrms coil to contact
(at sea level for 1 min.) 1000 Vrms between open contacts
Insulation
Resistance
1000 megohms min. at 20°C, 500 VDC,
50% RH
Dropout
Greater than 10% of nominal coil voltage
Ambient Temperature
Operating
Storage
At nominal coil voltage
-40°C (-40°F) to 70°C (158°F)
-40°C (-40°F) to 110°C (230°F)
Vibration
0.062" DA at 10–55 Hz
Shock
20 g
Enclosure
P.B.T. polyester
Terminals
Tinned copper alloy, P.C.
Max. Solder Temp.
270°C (518°F)
Max. Solder Time
5 seconds
Max. Solvent Temp.
80°C (176°F)
Max. Immersion Time
30 seconds
Weight
14 grams
1. All values at 20°C (68°F).
2. Relay may pull in with less than “Must Operate” value.
3. Specifications subject to change without notice.
1/15/13
AZ696
RELAY ORDERING DATA
COIL SPECIFICATIONS
Nominal Coil
VDC
5
Must Operate
VDC
3.5
Max Continuous
VDC
12.0
ORDER NUMBER
Coil Resistance
Ohms ± 10%
110
1 Form A
(SPST-NO)
AZ696–1A–5D
1 Form C
(SPDT)
AZ696–1C–5D
AZ696–1C–6D
6
4.2
14.5
160
AZ696–1A–6D
9
6.3
22.0
360
AZ696–1A–9D
AZ696–1C–9D
12
8.4
29.5
660
AZ696–1A–12D
AZ696–1C–12D
18
12.6
44.0
1,500
AZ696–1A–18D
AZ696–1C–18D
24
16.8
54.0
2,200
AZ696–1A–24D
AZ696–1C–24D
48
33.6
102.0
8,000
AZ696–1A–48D
AZ696–1C–48D
* Substitute “1B” in place of “1A” for 1 Form B contact. ADD suffix “E” to “1A” or “1B” or “1C” for silver tin oxide contacts.
Add Suffix “E” at the end of order number for sealed version. When suffix “E” is specified for Epoxy Seal, refer to AZ “Relay Technical Notes”
on AZ website - Product Resources. Consult factory for other PCB process conditions that may apply.
INTERNATIONAL APPROVALS
Germany
VDE 0435/09.72 at 8 Amps
VDE 0631/12.83 at 8 Amps
VDE 0700/1/2.81 at 8 Amps
MECHANICAL DATA
Coil Temperature Rise
Maximum Switching Capacity
Dimensions in inches with metric equivalents in parentheses. Tolerance: ± .010"
1/15/13