AZ2150W 30 AMP MINIATURE POWER RELAY FEATURES • • • • • • • • 1.75 mm contact gap DC coils up to 48V High dielectric strength version available All plastics PTI 250 Epoxy sealed versions available UL Class F (155°C) standard UL, CUR E44211 VDE certificate 40023154 CONTACTS Arrangement Ratings GENERAL DATA SPST (1 Form A) Resistive load: Max. switched power: 900W or 8310VA Max. switched current: 30A Max. switched voltage: 250 VDC* or 440 VAC Life Expectancy Mechanical Electrical Minimum operations 2 x 105 3 x 104 at 30 A 250 VAC Res. Operate Time 15 msec max. at nominal coil voltage Release Time 10 msec max. at nominal coil voltage (without suppression) Dielectric Strength 3000 Vrms between open contacts 4000 Vrms contact to coil * Note: If switching voltage is greater than 30 VDC, special precautions must be taken. Please contact the factory. UL, CUR VDE Material Resistance 30A at 277 VAC, General Use, Resistive 20A at 250 VAC, AC7a Silver tin oxide < 50 milliohms initially (24V, 1A voltage drop method) COIL Power At Pickup Voltage (typical) 625mW Max. Continuous Dissipation 1.7W at 20°C (68°F) ambient Temperature Rise 43°C (77°F) at nominal coil voltage Max. Temperature 155°C (311°F) Class F NOTES (at sea level for 1 min.) Holding Voltage Greater than 50% of nominal coil voltage Insulation Resistance 1000 megohms min. at 20°C, 500 VDC 50% RH Dropout Greater than 10% of nominal coil voltage Ambient Temperature Operating Storage -40°C (-40°F) to 85°C (185°F) - DC coils Vibration 0.062" (1.5 mm) DA at 10–55 Hz Shock 10 g Enclosure P.B.T. polyester Terminals Tinned copper alloy, P.C., Max. Solder Temp. 270°C (518°F) Max. Solder Time 5 seconds Max. Solvent Temp. 80°C (176°F) Max. Immersion Time 30 seconds Weight 25 grams Packing unit in pcs 40 per plastic tray / 280 per carton box 1. All values at 20°C (68°F). 2. Relay may pull in with less than “Must Operate” value. 3. Specifications subject to change without notice. 4. If higher electrical loads are to be switched by the relay contacts, the vent nib has to be opened prior to use of the relay. 8/17/15 AZ2150W RELAY ORDERING DATA Nominal Coil VDC 5 COIL SPECIFICATIONS – DC Coil Min. Holding VDC 2.5 ORDER NUMBER* Coil Resistance Ohm ± 10% 22.5 Must Operate VDC 3.75 Max. Continuous VDC 6.0 6 4.50 7.2 3.0 32.5 AZ2150W–1AE–6DF 9 6.75 10.8 4.5 73 AZ2150W–1AE–9DF AZ2150W–1AE–5DF 12 9.0 14.4 6.0 130 AZ2150W–1AE–12DF 24 18.0 38.8 12.0 520 AZ2150W–1AE–24DF 48 36.0 57.6 24.0 2,080 AZ2150W–1AE–48DF * Substitute “DEF” in place of “DF” for epoxy sealed version. Add “T” at the end of part number for 4000Vrms dielectric strength version. Coils 5VDC, 6VDC, 48VDC, not VDE approved. MECHANICAL DATA 1.25 (31.80) .130 + .020 - .010 (3.3 + .051 - .025 PC BOARD LAYOUT 2 x ø .079 [ø 2.0] .400 (10.16) .500 (12.7) .690 (17.5) .100 (2.54) ) 1.000 (25.4) 2 x ø .044 (ø 1.1) .090 (2.3) .196 (5.0) 1.063 (27.0) .751 (19.1) .200 (5.1) .150 (3.8) .550 (14.0) .700 (17.8) Viewed toward terminals WIRING DIAGRAMS .400 (10.16) Form A .032 x .062 (0.81 x 1.57) .045 x .045 (1.14 x 1.14) .025 x .025 (0.63 x 0.63) Viewed toward terminals Dimensions in inches with metric equivalents in parentheses. Tolerance: ± .010" 8/17/15