BT05AG 5-4000 MHz Wideband Drive Amplifier Device Features OIP3 = 40.0 dBm @ 1900 MHz Gain = 20.8 dB @ 900 MHz Output P1 dB = 22.4 dBm @ 900 MHz 50 Ω Cascadable Lead-free/RoHS-compliant SOT-89 SMT package Product Description Typical Performance1 BeRex’s BT05AG is a high performance and a high dynamic range amplifier in a low cost surface mount package(SOT-89) with a RoHS -compliant, that incorporates reliable heterojunction-bipolar-transistor (HBT) devices fabricated with InGaP GaAs technology. This device is designed for use where high linearity is required and features high OIP3 and P1 with low consumption current (85mA) and requires a few external matching components such as a DC blocking capacitors on the In/Output pin, a bypass capacitor and a RF choke for the out port. All devices are 100% RF/DC tested. Parameter Applications Vcc Bypass RF Choke RF In RF Out BT05AG DC Block DC Block Unit 900 1900 2450 3500 MHz Gain 20.8 16.3 14.3 11.1 dB S11 -14.0 -20.0 -22.0 -16.0 dB -12.0 -12.0 -12.0 -13.0 dB 37.0 22.4 4.5 40.0 19.5 4.4 37.5 23.0 4.3 40.0 22.8 4.5 dBm dBm dB S22 2 OIP3 P1dB Noise Figure 1 Device performance _ measured on a BeRex evaluation board at 25°C, 50 Ω system. 2 OIP3 _ measured with two tones at an output of 10 dBm per tone separated by 1 MHz. Min. Bandwidth IC @ (Vc = 5V) VC RTH Base station Infrastructure/RFID Commercial/Industrial/Military wireless system Application Circuits Frequency Typical 5 75 85 5.0 50 Max. Unit 4000 95 MHz mA V °C/W Absolute Maximum Ratings Parameter Operating Case Temperature Storage Temperature Junction Temperature Operating Voltage Supply Current Input RF Power Rating -40 to +85 -55 to +155 +220 Unit °C °C °C +7.0 180 23 V mA dBm *Operation of this device above any of these parameters may result in permanent damage. *external matching circuit: refer to the page 5 to 11. BeRex ●website: www.berex.com ● email: [email protected] 1 Specifications and information are subject to change and products may be discontinued without notice. BeRex is a trademark of BeRex. All other trademarks are the property of their respective owners. © 2010 BeRex Rev. D BT05AG 5-4000 MHz Wideband Drive Amplifier V-I Characteristics BeRex SOT89 Evaluation Board BeRex Evaluation Board *Dielectric constant _ 4.2 *RF pattern width 52mil *31mil thick FR4 PCB Typical Device Data S-parameters (Vc=5V, Ic=84mA, T=25°C) BeRex ●website: www.berex.com ● email: [email protected] 2 Specifications and information are subject to change and products may be discontinued without notice. BeRex is a trademark of BeRex. All other trademarks are the property of their respective owners. © 2010 BeRex Rev. D BT05AG 5-4000 MHz Wideband Drive Amplifier S-Parameter (Vdevice = 5.0V, Icc = 84mA, T = 25 °C, calibrated to device leads) Freq [MHz] S11 S11 S21 S21 S12 S12 S22 S22 Mag Ang Mag Ang Mag Ang Mag Ang 100 500 1000 1500 2000 2500 3000 3500 -10.6001 -6.89632 -4.83571 -4.36842 -4.49519 -4.82222 -4.64574 -3.85543 -176.08 171.969 137.774 107.055 77.2739 43.2334 3.39018 -35.846 24.3773 22.4951 19.3111 16.5624 14.5732 13.1214 11.7047 9.92492 166.26 118.889 75.4763 42.7846 13.4329 -15.725 -45.735 -74.765 -29.173 -28.510 -27.637 -27.010 -26.080 -25.166 -24.318 -25.101 -0.828 -5.512 -16.88 -29.70 -41.79 -58.33 -79.25 -100.4 -21.805 -20.525 -17.519 -16.447 -17.536 -22.101 -27.037 -16.664 -27.056 -120.815 170.039 137.451 118.289 99.7268 4.66192 -50.8784 4000 -3.0184 -66.883 8.4767 -100.82 -24.247 -119.41 -11.732 -71.031 WCDMA 6FA 2140 -55dBc BeRex ●website: www.berex.com ● email: [email protected] 3 Specifications and information are subject to change and products may be discontinued without notice. BeRex is a trademark of BeRex. All other trademarks are the property of their respective owners. © 2010 BeRex Rev. D BT05AG 5-4000 MHz Wideband Drive Amplifier WCDMA 6FA 2140 -60dBc ACLR BeRex ●website: www.berex.com ● email: [email protected] 4 Specifications and information are subject to change and products may be discontinued without notice. BeRex is a trademark of BeRex. All other trademarks are the property of their respective owners. © 2010 BeRex Rev. D BT05AG 5-4000 MHz Wideband Drive Amplifier Application Circuit: 900 MHz Schematic Diagram BOM C1 C2 C3 +5V L1 RFin C4 C7 RFout C5 BT05AG C6 L2 C1 C2 C3 C4 C5 C6 C7 L1 L2 Tolerance 100pF 1000pF 10uF 100pF 100pF 1pF 4.7pF 39nH 5.6nH ±5% ±5% ±20% ±5% ±5% ±5% ±5% ±5% ±5% Note: 10uF 1000 pF 1. PCB: 31mil thick FR4 2. Distance between the center of the series cap (C7) and the input pin of BT05AG _ 2.0mm. 3. Distance between the center of the shunt inductor(L2) and the input pin of BT05AG _ 4.1mm. 4. Distance between the center of the shunt cap (C6) and the input pin of BT05AG _ 6.5mm. 100pF 100 pF BT05AG BT013 4.7pF 100pF 1pF 39nH BB 100pF B 5.6nH Typical Performance 0 0 +25C +25C -5 -5 +85C S22 [dB] S11 [dB] -30C -30C -10 -15 -10 -15 -20 800 +85C 850 900 950 1000 -20 800 850 Freq [MHz] BeRex ●website: www.berex.com 900 950 1000 Freq [MHz] ● email: [email protected] 5 Specifications and information are subject to change and products may be discontinued without notice. BeRex is a trademark of BeRex. All other trademarks are the property of their respective owners. © 2010 BeRex Rev. D BT05AG 5-4000 MHz Wideband Drive Amplifier 25 23 70 60 22 20 50 20 15 40 30 10 19 20 +25C Po 5 -30C 18 G +85C 0 850 900 950 0 -20 1000 -14 -8 40 0 38 -10 34 32 +25C -30C +85C -40 -50 -70 26 12 +85C -30 -60 -30C 10 10 +25C -20 36 28 4 900MHz, 885KHz offset 9-Ch FWD, IS-95 ACPR [dBc] OIP3 [dBm] F1=900MHz, F2=901MHz 30 -2 Pin [dBm ] Freq [MHz] 14 16 18 -80 10 12 Po, 2tone [dBm ] BeRex 10 PAE 17 800 PAE [%] Po, G S21 [dB] 21 ●website: www.berex.com 14 16 18 Po [dBm ] ● email: [email protected] 6 Specifications and information are subject to change and products may be discontinued without notice. BeRex is a trademark of BeRex. All other trademarks are the property of their respective owners. © 2010 BeRex Rev. D BT05AG 5-4000 MHz Wideband Drive Amplifier Application Circuit: 1900 MHz Schematic Diagram BOM C1 C2 C3 +5V L1 RFin L2 C4 RFout C5 BT05AG C6 C7 C1 C2 C3 C4 C5 C6 C7 L1 L2 Tolerance 100pF 100pF 10uF 100pF 100pF 2pF 1pF 39nH 3.3nH ±5% ±5% ±20% ±5% ±5% ±5% ±5% ±5% ±5% Note: 10uF 1000 pF 1. PCB: 31mil thick FR4 2. Distance between the center of the shunt cap (C6) and the input pin of BT05AG _ 1.8mm. 3. Distance between the center of the series inductor(L2) and the output pin of BT05AG _ 3.5mm. 4. Distance between the center of the shunt cap (C7) and the output pin of BT05AG _ 5.9mm. 100pF 100 pF BT05AG BT013 39nH BB 100pF 100pF B 2pF 3.3nH 1pF Typical Performance BeRex ●website: www.berex.com ● email: [email protected] 7 Specifications and information are subject to change and products may be discontinued without notice. BeRex is a trademark of BeRex. All other trademarks are the property of their respective owners. © 2010 BeRex Rev. D BT05AG 5-4000 MHz Wideband Drive Amplifier BeRex ●website: www.berex.com ● email: [email protected] 8 Specifications and information are subject to change and products may be discontinued without notice. BeRex is a trademark of BeRex. All other trademarks are the property of their respective owners. © 2010 BeRex Rev. D BT05AG 5-4000 MHz Wideband Drive Amplifier Application Circuit: 2450MHz Schematic Diagram BOM C1 C2 C3 +5V L1 RFin C4 RFout C5 BT05AG C6 C1 C2 C3 C4 C5 C6 L1 100pF 1000pF 10uF 100pF 100pF 1.2pF 39nH Tolerance ±5% ±5% ±20% ±5% ±5% ±5% ±5% Note: 10uF 1000 pF 100pF 100 pF BT05AG BT013 BB 100pF B 1. PCB: 31mil thick FR4 2. Distance between the center of the shunt cap (C6) and the input pin of BT05AG _ 0.5mm. 39nH 100pF 1.2pF Typical Performance BeRex ●website: www.berex.com ● email: [email protected] 9 Specifications and information are subject to change and products may be discontinued without notice. BeRex is a trademark of BeRex. All other trademarks are the property of their respective owners. © 2010 BeRex Rev. D BT05AG 5-4000 MHz Wideband Drive Amplifier BeRex ●website: www.berex.com ● email: [email protected] 10 Specifications and information are subject to change and products may be discontinued without notice. BeRex is a trademark of BeRex. All other trademarks are the property of their respective owners. © 2010 BeRex Rev. D BT05AG 5-4000 MHz Wideband Drive Amplifier Application Circuit: 3500MHz Schematic Diagram BOM C1 C2 +5V C3 L1 RFin L2 C4 RFout BT05AG C6 C5 C7 C1 C2 C3 C4 C5 C6 C7 L1 L2 Tolerance 100pF 1000pF 10uF 18pF 18pF 0.75pF 0.5pF 33nH 2.7nH ±5% ±5% ±20% ±5% ±5% ±5% ±5% ±5% ±5% Note: 10uF 1000 pF 100pF 100 pF BT05AG BT013 2.7nH 33nH BB 18pF PCB: 31mil thick FR4 2. Distance between the center of the series inductor(L2) and the input pin of BT05AG _ 2.0mm. 3. Distance between the center of the shunt cap(C6) and the input pin of BT05AG _ 0.5mm. 4. Distance between the center of the shunt cap(C7) and the output pin of BT05AG _ 10.0mm. 18pF B 0.75pF 1. 0.5pF Typical Performance BeRex ●website: www.berex.com ● email: [email protected] 11 Specifications and information are subject to change and products may be discontinued without notice. BeRex is a trademark of BeRex. All other trademarks are the property of their respective owners. © 2010 BeRex Rev. D BT05AG 5-4000 MHz Wideband Drive Amplifier BeRex ●website: www.berex.com ● email: [email protected] 12 Specifications and information are subject to change and products may be discontinued without notice. BeRex is a trademark of BeRex. All other trademarks are the property of their respective owners. © 2010 BeRex Rev. D BT05AG 5-4000 MHz Wideband Drive Amplifier Package Outline Dimension Suggested PCB Land Pattern and PAD Layout PCB Land Pattern 0.40 1.30 PCB Mounting 0.40 Ø0.40 0.40 0.75 1.20 2.15 1.20 0.50 0.45 1.20 1.20 2.80 1.50 1.00 0.65 0.35 Note : All dimension _ millimeters PCB lay out _ on BeRex website BeRex ●website: www.berex.com ● email: [email protected] 13 Specifications and information are subject to change and products may be discontinued without notice. BeRex is a trademark of BeRex. All other trademarks are the property of their respective owners. © 2010 BeRex Rev. D BT05AG 5-4000 MHz Wideband Drive Amplifier Package Marking Tape & Reel SOT89 Packaging information: Tape Width (mm): 12 Reel Size (inches): 7 Device Cavity Pitch (mm): 8 YY = Year, WW = Working Week, XX = Wafer No. Devices Per Reel: 1000 Lead plating finish 100% Tin Matte finish (All BeRex products undergoes a 1 hour, 150 degree C, Anneal bake to eliminate thin whisker growth concerns.) MSL / ESD Rating ESD Rating: Class 1B Value: Passes <1000V Test: Human Body Model (HBM) Standard: JEDEC Standard JESD22-A114B MSL Rating: Level 1 at +265°C convection reflow Standard: JEDEC Standard J-STD-020 NATO CAGE code: 2 BeRex N 9 6 F ●website: www.berex.com ● email: [email protected] 14 Specifications and information are subject to change and products may be discontinued without notice. BeRex is a trademark of BeRex. All other trademarks are the property of their respective owners. © 2010 BeRex Rev. D