BT301 - Berex

BT301
500-4000 MHz High Power Amplifier
Device Features






OIP3 = 49.0 dBm @ 1900 MHz
Gain = 12.5 dB @ 1900 MHz
Output P1 dB = 30.3 dBm @ 1900 MHz
50 Ω Cascadable
Patented Over Voltage Protection Circuit
Lead-free/RoHS-compliant SOIC-8 package
YY = Year, WW = Work week,
XX = Wafer Number
Product Description
Typical Performance1
BeRex’s BT301 is a high power and a high
dynamic range amplifier in a low cost surface mount package(SOIC-8) with a RoHScompliant, that incorporates reliable heterojunction-bipolar-transistor (HBT) devices
fabricated with InGaP GaAs technology.
This device is designed for use where high
linearity is required and features high OIP3
and Power with low consumption current
(350mA) and requires a few external matching components such as a DC blocking capacitors on the In/Output pin, a bypass capacitor and a RF choke for the out port.
All devices are 100% RF/DC tested.
Parameter
 Base station Infrastructure/RFID
 Commercial/Industrial/Military wireless system
Application Circuits
900
1900
2140
2450
3500
MHz
Gain
18.5
12.5
11.5
10.5
7.6
dB
S11
-15
-18
-18
-12
-23.2
dB
S22
-7
-12
-12
-11
-17.4
dB
OIP32
49
49
47
49
42.5
dBm
P1dB
29.5
30.3
30.3
30.3
27.9
dBm
IS-95C ACPR
22.5
22.5
-
-
-
dBm
WCDMA ACLR
-
-
21
21
18.4
dBm
Noise Figure
8.5
8.6
7.5
7.5
7.3
dB
1
Device performance _ measured on a BeRex evaluation board at 25°C, 50 Ω system.
2
OIP3 _ measured with two tones at an output of 16 dBm per tone separated by 1 MHz.
*ACPR&ACLR CH Power _ measured at 50dBc.
*ACPR Test set-up: IS-95 CDMA, 9Ch. FWD, +885KHz offset.
Min.
Bandwidth
IC @ (Vc = 5V)
VC
RTH
Vcc
RF Choke
RF Out
BT301
DC
Block
*external matching circuit: refer to the page 4 to 11.
Typical
500
310
350
5.0
19.6
Max.
Unit
4000
390
MHz
mA
V
°C/W
Absolute Maximum Ratings
Bypass
DC
Block
Unit
*ACLR Test set-up: 3GPP WCDMA, TM1+64DPCH, +5MHz offset.
Applications
RF In
Frequency
Parameter
Operating Case Temperature
Storage Temperature
Junction Temperature
Operating Voltage
Supply Current
Input RF Power
Rating
-40 to +85
-55 to +155
+220
Unit
°C
°C
°C
+6.0
600
28
V
mA
dBm
*Operation of this device above any of these parameters may result in permanent damage.
BeRex
●website: www.berex.com
● email: [email protected]
1
Specifications and information are subject to change and products may be discontinued without notice. BeRex is a trademark of BeRex.
All other trademarks are the property of their respective owners. © 2015 BeRex
Rev. E
BT301
500-4000 MHz High Power Amplifier
V-I Characteristics
BeRex SOIC-8 Evaluation Board
*Dielectric constant _ 4.2 *RF pattern width 52mil *31mil thick FR4 PCB
Typical Device Data
S-parameters (Vc=5V, Ic=340mA, T=25°C)
BeRex
●website: www.berex.com
● email: [email protected]
2
Specifications and information are subject to change and products may be discontinued without notice. BeRex is a trademark of BeRex.
All other trademarks are the property of their respective owners. © 2015 BeRex
Rev. E
BT301
500-4000 MHz High Power Amplifier
S-Parameter
(Vdevice = 5.0V, Icc = 340mA, T = 25 °C, calibrated to device leads)
Freq
[MHz]
100
500
1000
1500
2000
2500
3000
3500
4000
BeRex
S11
[Mag]
S11
[Ang]
0.842
0.895
0.893
0.870
0.852
0.840
0.841
0.850
0.879
-178.0
157.3
130.8
106.2
82.2
58.8
35.6
12.5
-6.4
S21
[Mag]
11.489
4.894
2.766
1.658
1.512
1.047
0.888
0.840
0.542
●website: www.berex.com
S21
[Ang]
S12
[Mag]
131.4
104.8
83.9
75.1
64.0
47.2
50.8
36.8
24.0
S12
[Ang]
0.019
0.023
0.022
0.025
0.027
0.026
0.029
0.031
0.031
18.2
10.6
9.8
21.7
21.5
21.6
16.4
23.4
16.3
S22
[Mag]
0.534
0.659
0.754
0.773
0.761
0.773
0.792
0.659
0.634
● email: [email protected]
S22
[Ang]
-134.7
-176.7
160.4
139.8
120.1
101.7
83.2
62.6
41.3
3
Specifications and information are subject to change and products may be discontinued without notice. BeRex is a trademark of BeRex.
All other trademarks are the property of their respective owners. © 2015 BeRex
Rev. E
BT301
500-4000 MHz High Power Amplifier
Application Circuit: 900 MHz
Schematic Diagram
Vcc
C3
C2
C1
L2
C8
L1
R1
1
8
2
7
3
6
4
5
NC
RF_OUT
RF_IN
C4
C6
5.6mm
Tolerance
BOM
C5
12mm C7
C1
C2
C3
C4
C5
C6
C7
C8
R1
L1
L2
1206
0603
0603
0603
0603
0603
0603
0603
0603
1008
0603
PCB Diagram
10uF
1.0nF
100pF
3pF
100pF
4.7pF
5.0pF
2.7pF
12ohm
56nH
4.7nH
±20%
±5%
±5%
±5%
±5%
±5%
±5%
±5%
±5%
±5%
±5%
Notice
1.
PCB: 31mil thick FR4
2.
Distance between the center of the shunt Inductor(C6) and the input pin of BT301 _ 5.6 mm.
3.
Distance between the center of the shunt cap.
(C7) and the output pin of BT301 _ 12 mm.
※ BT301 with both input and output ports opened
simultaneously may cause instability. Please See an
application note or contact company for application
support.
BeRex
●website: www.berex.com
● email: [email protected]
4
Specifications and information are subject to change and products may be discontinued without notice. BeRex is a trademark of BeRex.
All other trademarks are the property of their respective owners. © 2015 BeRex
Rev. E
BT301
500-4000 MHz High Power Amplifier
Typical Performance
BeRex
●website: www.berex.com
● email: [email protected]
5
Specifications and information are subject to change and products may be discontinued without notice. BeRex is a trademark of BeRex.
All other trademarks are the property of their respective owners. © 2015 BeRex
Rev. E
BT301
500-4000 MHz High Power Amplifier
Typical Performance
BeRex
●website: www.berex.com
● email: [email protected]
6
Specifications and information are subject to change and products may be discontinued without notice. BeRex is a trademark of BeRex.
All other trademarks are the property of their respective owners. © 2015 BeRex
Rev. E
BT301
500-4000 MHz High Power Amplifier
Application Circuit: 1900 MHz
Schematic Diagram
Vcc
C3
L2
1.6mm
C8
C6
C2
C1
L1
1
8
2
7
3
6
4
5
NC
RF_OUT
RF_IN
C4
R1
4.0mm
C5
2.5mm C7
C1
C2
C3
C4
C5
C6
C7
C8
R1
L1
L2
1206
0603
0603
0603
0603
0603
0603
0603
0603
1008
0603
PCB Diagram
BeRex
Tolerance
BOM
●website: www.berex.com
10uF
1nF
100pF
100pF
100pF
3pF
2.5pF
2.5pF
12 ohm
56nH
6.8nH
±20%
±5%
±5%
±5%
±5%
±5%
±5%
±5%
±5%
±5%
±5%
Notice
1.
PCB: 31mil thick FR4
2.
Distance between the center of the series cap.
(C8) and the input pin of BT301 _ 1.6 mm.
3.
Distance between the center of the shunt cap.
(C6) and the input pin of BT301 _ 4.0 mm.
4.
Distance between the center of the shunt cap.
(C7) and the output pin of BT301 _ 2.5 mm.
● email: [email protected]
7
Specifications and information are subject to change and products may be discontinued without notice. BeRex is a trademark of BeRex.
All other trademarks are the property of their respective owners. © 2015 BeRex
Rev. E
BT301
500-4000 MHz High Power Amplifier
Typical Performance
BeRex
●website: www.berex.com
● email: [email protected]
8
Specifications and information are subject to change and products may be discontinued without notice. BeRex is a trademark of BeRex.
All other trademarks are the property of their respective owners. © 2015 BeRex
Rev. E
BT301
500-4000 MHz High Power Amplifier
BeRex
●website: www.berex.com
● email: [email protected]
9
Specifications and information are subject to change and products may be discontinued without notice. BeRex is a trademark of BeRex.
All other trademarks are the property of their respective owners. © 2015 BeRex
Rev. E
BT301
500-4000 MHz High Power Amplifier
Application Circuit: 2140MHz
Schematic Diagram
Vcc
C3
L2
1.6mm
C8
RF_IN
C4
C6
3.0mm
R1
C2
C1
L1
1
8
2
7
3
6
4
5
NC
RF_OUT
C5
2.5mm C7
C1
C2
C3
C4
C5
C6
C7
C8
C9
R1
L1
L2
1206
0603
0603
0603
0603
0603
0603
0603
0603
0603
1008
0603
PCB Diagram
BeRex
Tolerance
BOM
●website: www.berex.com
10uF
1nF
100pF
100pF
100pF
2.5pF
1.8pF
1.8pF
5.0pF
12 ohm
56nH
4.7nH
±20%
±5%
±5%
±5%
±5%
±5%
±5%
±5%
±5%
±5%
±5%
±5%
Notice
1.
PCB: 31mil thick FR4
2.
Distance between the center of the shunt cap.
(C8) and the input pin of BT301 _ 1.6 mm.
3.
Distance between the center of the shunt cap.
(C6) and the input pin of BT301 _ 3.0 mm.
4.
Distance between the center of the shunt cap.
(C7) and the output pin of BT301 _ 2.5 mm.
● email: [email protected]
10
Specifications and information are subject to change and products may be discontinued without notice. BeRex is a trademark of BeRex.
All other trademarks are the property of their respective owners. © 2015 BeRex
Rev. E
BT301
500-4000 MHz High Power Amplifier
Typical Performance
BeRex
●website: www.berex.com
● email: [email protected]
11
Specifications and information are subject to change and products may be discontinued without notice. BeRex is a trademark of BeRex.
All other trademarks are the property of their respective owners. © 2015 BeRex
Rev. E
BT301
500-4000 MHz High Power Amplifier
BeRex
●website: www.berex.com
● email: [email protected]
12
Specifications and information are subject to change and products may be discontinued without notice. BeRex is a trademark of BeRex.
All other trademarks are the property of their respective owners. © 2015 BeRex
Rev. E
BT301
500-4000 MHz High Power Amplifier
Application Circuit: 2450MHz
Schematic Diagram
Vcc
C3
L2
1.6mm
C8
RF_IN
C4
C6
3.4mm
R1
C2
C1
L1
1
8
2
7
3
6
4
5
NC
RF_OUT
C5
2.0mm C7
C1
C2
C3
C4
C5
C6
C7
C8
R1
L1
L2
1206
0603
0603
0603
0603
0603
0603
0603
0603
1008
0603
PCB Diagram
BeRex
Tolerance
BOM
●website: www.berex.com
10uF
1nF
100pF
100pF
100pF
1.5pF
1.5pF
1.8pF
12 ohm
56nH
3.9nH
±20%
±5%
±5%
±5%
±5%
±5%
±5%
±5%
±5%
±5%
±5%
Notice
1.
PCB: 31mil thick FR4
2.
Distance between the center of the series cap.
(C8) and the input pin of BT301 _ 1.6 mm.
3.
Distance between the center of the shunt cap.
(C6) and the input pin of BT301 _ 3.4 mm.
4.
Distance between the center of the shunt cap.
(C7) and the output pin of BT301 _ 2.0 mm.
● email: [email protected]
13
Specifications and information are subject to change and products may be discontinued without notice. BeRex is a trademark of BeRex.
All other trademarks are the property of their respective owners. © 2015 BeRex
Rev. E
BT301
500-4000 MHz High Power Amplifier
Typical Performance
BeRex
●website: www.berex.com
● email: [email protected]
14
Specifications and information are subject to change and products may be discontinued without notice. BeRex is a trademark of BeRex.
All other trademarks are the property of their respective owners. © 2015 BeRex
Rev. E
BT301
500-4000 MHz High Power Amplifier
BeRex
●website: www.berex.com
● email: [email protected]
15
Specifications and information are subject to change and products may be discontinued without notice. BeRex is a trademark of BeRex.
All other trademarks are the property of their respective owners. © 2015 BeRex
Rev. E
BT301
500-4000 MHz High Power Amplifier
Package Outline Dimension
BeRex
●website: www.berex.com
● email: [email protected]
16
Specifications and information are subject to change and products may be discontinued without notice. BeRex is a trademark of BeRex.
All other trademarks are the property of their respective owners. © 2015 BeRex
Rev. E
BT301
500-4000 MHz High Power Amplifier
Suggested PCB Land Pattern and PAD Layout
PCB Land Pattern
PCB Mounting
Ø0.86
2.0
1.0
1.9
Ø0.25
11.00
Ø2.30
8.86
Ø0.45
1.3
2.0
Note : All dimension are in millimeters
PCB lay out _ on BeRex website
Package Marking
YY = Year, WW = Working Week,
XX = Wafer No.
Tape & Reel
Packaging information:
SOIC8
SOIC8-Part orientation
Tape Width (mm): 12
Reel Size (inches): 7
Device Cavity Pitch (mm): 8
Direction of feed
BeRex
Devices Per Reel: 1000
●website: www.berex.com
● email: [email protected]
17
Specifications and information are subject to change and products may be discontinued without notice. BeRex is a trademark of BeRex.
All other trademarks are the property of their respective owners. © 2015 BeRex
Rev. E
BT301
500-4000 MHz High Power Amplifier
Lead plating finish
100% Tin Matte finish
(All BeRex products undergoes a 1 hour, 150 degree C, Anneal bake to eliminate
thin whisker growth concerns.)
MSL / ESD Rating
ESD Rating:
Class 1B
Value:
Passes <1000V
Test:
Human Body Model (HBM)
Standard:
JEDEC Standard JESD22-A114B
MSL Rating:
Level 1 at +265°C convection reflow
Standard:
JEDEC Standard J-STD-020
NATO CAGE code:
2
BeRex
N
9
6
F
●website: www.berex.com
● email: [email protected]
18
Specifications and information are subject to change and products may be discontinued without notice. BeRex is a trademark of BeRex.
All other trademarks are the property of their respective owners. © 2015 BeRex
Rev. E