ElectroFilm ElectroFilm Technology A Film Alternative for Electrolytic Capacitors Metallized Polyester & Polypropylene Screw Terminal, Snap-In and Custom Case Configurations ElectroFilm Technology is a material system used by CDE to fabricate custom capacitors for stable high capacitance, high voltage and/or high current and low ESR applications. ElectroFilm can be made with metallized polypropylene or metallized polyester at very high capacitance values and could be used to replace electrolytic capacitors where increased reliability is desired. ElectroFilm is self-healing, nonpolar, and typically has 10 times the ripple current capability, 20 times greater life expectancy and 500 times lower ESR than comparable electrolytic capacitors. A lower in-place cost is achieved by using ElectroFilm Capacitors, because 65% fewer capacitors are generally needed when compared to aluminum electrolytic capacitors for the same application. Features Voltage Range: 300 Vdc to 1200 Vdc Capacitance Range: 7.5 µF to 600 µF Operating Temperature Range: -55° C to +85° C Ripple Current Capability: 25 °C 13.8 Arms to 39.2 Arms 50 °C 11.1 Arms to 31.5 Arms 75 °C 6.8 Arms to 19.2 Arms Type Designation UNL - Snap-In Capacitor Metallized Polypropylene UPP - Screw Terminal Metallized Polypropylene UPE - Screw Terminal Metallized Polyester Cornell Dubilier Electronics 1605 East Rodney French Blvd. New Bedford, MA 02744 Phone: (508)996-8564 Fax: (508)996-3830 www.cde.com CDE ElectroFilm Capacitors - Alternative to Aluminum Electrolytics Catalog Number UNL12W7P5K UNL6W30K UNL5W35K UPE10W120K UPE6W240K UPE3W600K UPP12W30K UPP12W60K UPP6W120K Cap µF 7.5 30 35 120 240 600 30 60 120 Vdc Diel. 1200 600 500 1000 600 300 1200 1200 600 MPP MPP MPP MPE MPE MPE MPP MPP MPP H D In. 1.42 1.42 1.42 3.00 3.00 3.00 2.50 2.50 2.50 mm 36.07 36.07 36.07 76.2 76.2 76.2 63.5 63.5 63.5 In. 2.12 2.12 2.12 5.13 4.13 3.13 3.13 4.13 3.13 mm 53.85 53.85 53.85 130.2 104.8 79.38 79.38 104.8 79.38 S 0.500 0.500 0.500 1.250 1.250 1.250 1.125 1.125 1.125 E.S.R. mΩ @ 1 kHz 14.0 8.0 8.0 18.0 8.5 5.0 6.2 7.5 5.0 25 °C Arms 50 °C Arms 75 °C Arms Joules dVdt V/µs IP ESL (nH) S.R.F. 13.8 18.1 18.6 25.6 32.7 39.2 30.3 31.1 36.7 11.1 14.6 15.0 20.6 26.2 31.5 24.3 24.9 29.4 6.8 8.9 9.1 12.5 16.0 19.2 14.8 15.2 18.0 5.40 5.40 4.38 60.0 43.2 27.0 21.6 43.2 21.6 56 28 25 19 14 11 47 27 23 420 840 875 2280 3360 6600 1410 1620 2760 35 35 35 81 61 47 42 82 43 309 155 143 71 42 30 143 70 70 kHz Pin: 0.050 " Tapered to 0.035 " Pin Base to Below Case Stand-off Leads to be tin dipped in 60/40 solder 0.200 " ± 0.005 " 0.100 " 0.315 " ± 0.005 " UPE & UPP 0.300 " + 0.015 " - 0.030 " 0.031 " ± 0.003 " H ± 0.031 " D ± 0.031" S ± 0.015 " D Max. 2 x∅ 0.687 " UNL 2 x 1/4-28 UNF Threads 0.38 " Deep Min. 0.13 " ± 0.063 " 0.312 " H ± 0.062 " S ± 0.031 " Cornell Dubilier Electronics 1605 East Rodney French Blvd. New Bedford, MA 02744 Phone: (508)996-8564 Fax: (508)996-3830 www.cde.com Rev. 5-20-2004