Nios Development Board Reference Manual, Cyclone Edition

Nios Development Board
Reference Manual, Cyclone Edition
101 Innovation Drive
San Jose, CA 95134
(408) 544-7000
www.altera.com
Document Version:
Document Date:
1.3
January 2004
Copyright
Nios Development Board, Cyclone Edition Reference Manual
Copyright © 2004 Altera Corporation. All rights reserved. Altera, The Programmable Solutions Company, the stylized Altera logo,
specific device designations, and all other words and logos that are identified as trademarks and/or service marks are, unless
noted otherwise, the trademarks and service marks of Altera Corporation in the U.S. and other countries. All other product or
service names are the property of their respective holders. Altera products are protected under numerous U.S. and foreign patents
and pending applications, mask work rights, and copyrights. Altera warrants performance of its semiconductor
products to current specifications in accordance with Altera’s standard warranty, but reserves the right to make
changes to any products and services at any time without notice. Altera assumes no responsibility or liability
arising out of the application or use of any information, product, or service described herein except as expressly
agreed to in writing by Altera Corporation. Altera customers are advised to obtain the latest version of device
specifications before relying on any published information and before placing orders for products or services.
ii
MNL-NIOSCYCBD-1.3
Altera Corporation
About this Manual
This manual provides component details about the Nios development
board, Cyclone edition.
Table 1 shows the reference manual revision history.
Table 1. Reference Manual Revision History
Date
How to Find
Information
January 2004
Pin table corrections.
July 2003
Reflects new directory structure for SOPC Builder 3.0 and
Nios Development Kit version 3.1.
May 2003
Minor revisions and edits.
March 2003
First publication of a reference manual. This manual is
Cyclone-device specific.
■
■
■
■
Altera Corporation
Description
The Adobe Acrobat Find feature allows you to search the contents of
a PDF file. Click the binoculars toolbar icon to open the Find dialog
box.
Bookmarks serve as an additional table of contents.
Thumbnail icons, which provide miniature previews of each page,
provide a link to the pages.
Numerous links, shown in green text, allow you to jump to related
information.
iii
About this Manual
How to Contact
Altera
Nios Development Board, Cyclone Edition Reference Manual
For the most up-to-date information about Altera products, go to the
Altera world-wide web site at http://www.altera.com.
For technical support on this product, go to
http://www.altera.com/mysupport. For additional information about
Altera products, consult the sources shown in Table 2.
Table 2. How to Contact Altera
Information Type
USA & Canada
All Other Locations
Product literature
http://www.altera.com
http://www.altera.com
Altera literature services
[email protected] (1)
[email protected] (1)
Non-technical customer
service
(800) 767-3753
(408) 544-7000
(7:30 a.m. to 5:30 p.m.
Pacific Time)
Technical support
(800) 800-EPLD (3753)
(7:30 a.m. to 5:30 p.m.
Pacific Time)
(408) 544-7000 (1)
(7:30 a.m. to 5:30 p.m.
Pacific Time)
http://www.altera.com/mysupport/
http://www.altera.com/mysupport/
FTP site
ftp.altera.com
ftp.altera.com
Note:
(1)
iv
You can also contact your local Altera sales office or sales representative.
Altera Corporation
Nios Development Board, Cyclone Edition Reference Manual
Typographic
Conventions
About this Manual
This manual uses the typographic conventions shown in Table 3.
Table 3. Conventions
Visual Cue
Meaning
Bold Type with Initial
Capital Letters
Command names, dialog box titles, checkbox options, and dialog box options are
shown in bold, initial capital letters. Example: Save As dialog box.
bold type
External timing parameters, directory names, project names, disk drive names,
filenames, filename extensions, and software utility names are shown in bold type.
Examples: fMAX, \QuartusII directory, d: drive, chiptrip.gdf file.
Bold italic type
Book titles are shown in bold italic type with initial capital letters. Example:
1999 Device Data Book.
Italic Type with Initial
Capital Letters
Document titles are shown in italic type with initial capital letters. Example: AN 75
(High-Speed Board Design).
Italic type
Internal timing parameters and variables are shown in italic type. Examples: tPIA, n + 1.
Variable names are enclosed in angle brackets (< >) and shown in italic type. Example:
<file name>, <project name>.pof file.
Initial Capital Letters
Keyboard keys and menu names are shown with initial capital letters. Examples:
Delete key, the Options menu.
“Subheading Title”
References to sections within a document and titles of Quartus II Help topics are
shown in quotation marks. Example: “Configuring a FLEX 10K or FLEX 8000 Device
with the BitBlaster™ Download Cable.”
Courier type
Signal and port names are shown in lowercase Courier type. Examples: data1, tdi,
input. Active-low signals are denoted by suffix n, e.g., resetn.
Anything that must be typed exactly as it appears is shown in Courier type. For
example: c:\quartusII\qdesigns\tutorial\chiptrip.gdf. Also, sections
of an actual file, such as a Report File, references to parts of files (e.g., the AHDL
keyword SUBDESIGN), as well as logic function names (e.g., TRI) are shown in
Courier.
1., 2., 3., and a., b., c.,... Numbered steps are used in a list of items when the sequence of the items is
important, such as the steps listed in a procedure.
■
Bullets are used in a list of items when the sequence of the items is not important.
v
The checkmark indicates a procedure that consists of one step only.
1
The hand points to information that requires special attention.
r
The angled arrow indicates you should press the Enter key.
f
The feet direct you to more information on a particular topic.
Altera Corporation
v
Table of Contents
About this Manual ...................................................................................................................................... iii
How to Find Information.............................................................................................................. iii
How to Contact Altera .................................................................................................................. iv
Typographic Conventions .............................................................................................................. v
Board Components .......................................................................................................................................9
Features ............................................................................................................................................. 9
General Description ......................................................................................................................... 9
Default Reference Design ....................................................................................................... 9
Restoring the Default Reference Design to the Board ...................................................... 10
Block Diagram ........................................................................................................................ 11
Nios Development Board Components...................................................................................... 12
The Cyclone EP1C20 Device ........................................................................................................ 13
Flash Memory Device.................................................................................................................... 13
Compact Flash Connector............................................................................................................. 14
SDRAM Device............................................................................................................................... 16
Dual SRAM Devices ...................................................................................................................... 18
Ethernet MAC/PHY...................................................................................................................... 19
Expansion Prototype Connector (PROTO1) .............................................................................. 19
Expansion Prototype Connector (PROTO2) .............................................................................. 21
Mictor Connector ........................................................................................................................... 23
Serial Port Connectors ................................................................................................................... 25
Dual 7-Segment Display ............................................................................................................... 26
Push-Button Switches.................................................................................................................... 26
Individual LEDs ............................................................................................................................. 27
Serial Configuration Device (EPCS4).......................................................................................... 27
Serial Flash Connector................................................................................................................... 27
Configuration Controller Device (EPM7128AE) ....................................................................... 28
Reset Distribution .................................................................................................................. 28
Starting Configuration .......................................................................................................... 28
Cyclone Configuration .......................................................................................................... 28
Configuration Data ................................................................................................................ 29
Safe and User Configurations .............................................................................................. 30
Using Conventional Flash Memory ............................................................................ 30
The Configuration-Status LEDs........................................................................................... 33
Configuration and Reset Buttons ........................................................................................ 33
SW8 – CPU Reset ........................................................................................................... 34
SW9 – Force Safe ............................................................................................................ 34
SW10 – Reset, Config..................................................................................................... 34
Altera Corporation
vii
Table of Contents
Nios Development Board Reference Manual, Cyclone Edition
Power-Supply Circuitry ................................................................................................................
Clock Circuitry ...............................................................................................................................
JTAG Connections .........................................................................................................................
JTAG to Cyclone Device (J24) ..............................................................................................
JTAG to MAX Device (J5) .....................................................................................................
35
35
36
36
38
Appendix A: Shared Bus Table .............................................................................................................39
Appendix B: Restore the Factory Configuration ...............................................................................43
Configuring the Cyclone Device.................................................................................................. 43
Reprogramming the Flash Memory ............................................................................................ 44
Appendix C: Board Ethernet Connection ............................................................................................45
Connecting the Ethernet Cable ............................................................................................ 45
Connecting the LCD Display ............................................................................................... 46
Obtaining an IP address: DHCP .......................................................................................... 46
IP Addresses for Point–to–Point Connections........................................................... 47
IP Addresses for LAN Connections ............................................................................ 48
Browsing your Board ............................................................................................................ 48
Index ................................................................................................................................................................49
viii
Altera Corporation
Board Components
Features
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
■
General
Description
A CycloneTM EP1C20F400C7device
8 Mbytes of flash memory
1 Mbyte of static RAM
16 Mbytes of SDRAM
On board logic for configuring the Cyclone device from flash
memory
EPCS4 serial configuration device
On-board Ethernet MAC/PHY device
Two 5-V-tolerant expansion/prototype headers each with access to
41 Cyclone user I/O pins
CompactFlashTM connector header for Type I Compact Flash (CF)
cards
Mictor connector for hardware and software debug
Two RS-232 DB9 serial ports
Four push-button switches connected to Cyclone user I/O pins
Eight LEDs connected to Straix user I/O pins
Dual 7-segment LED display
JTAG connectors to Altera devices via Altera download cables
50 MHz Oscillator and zero-skew clock distribution circuitry
Power-on reset circuitry
The Nios Development Board, Cyclone Edition, provides a hardware
platform for developing embedded systems based on Altera Cyclone
devices. The Nios development board features a Cyclone EP1C20F400C7
device with 20,060 logic elements (LEs) and 294 Kbits of on-chip memory.
The Nios development board comes pre-programmed with a 32-bit Nios
processor reference design. Hardware designers can use the reference
design as an example of how to use the features of the Nios development
board. Software designers can use the pre-programmed Nios processor
design on the board to begin prototyping software immediately.
Default Reference Design
When power is applied to the board, the on-board configuration logic
configures the Cyclone FPGA using hardware configuration data stored
in flash. When the device is configured, the Nios processor design in the
FPGA wakes up and begins executing boot code from flash memory.
Altera Corporation
9
Board Components
Nios Development Board Reference Manual, Cyclone Edition
The default reference design provides facilities to download new, userdefined software and hardware configuration data to the board from a
host computer. Download methods include a serial cable, a JTAG
download cable, or an Ethernet cable. The GERMS monitor, an Alteraprovided monitor program for the Nios processor, is running on the
Console RS-232 serial port (J19). Simultaneously, a web server program is
running via the ethernet connection.
1
f
The Ethernet port provides a very fast and easy method to
download hardware and software images to the board via a web
browser on your host computer. For instructions on
communicating with your Nios development board via
Ethernet, see “Appendix C: Board Ethernet Connection” on
page 45.
See the Nios Development Kit, Cyclone Edition Getting Started User Guide for
instructions on setting up the Nios development board. See the Nios
Hardware Development Tutorial for instructions on using this pre-loaded
reference design.
Restoring the Default Reference Design to the Board
In the course of development, you may overwrite or erase the flash
memory space containing the default reference design. Altera provides
the flash image for the default reference design, so that you can always
return the board to its default state. These default reference files are
located in the Nios development kit examples directory.
See “Appendix B: Restore the Factory Configuration” on page 43 for more
information.
10
Altera Corporation
Nios Development Board Reference Manual, Cyclone Edition
Board Components
Block Diagram
Figure 1 shows a block diagram of the board.
Figure 1. Nios Development Board, Cyclone Edition Block Diagram
50MHz Oscillator
16 Mbyte SDRAM
Serial Configuration
Device
5.0 V Regulators
Vccint (1.5 V)
Configuration
Controller
Vccio (3.3-V)
8 Mbyte Flash Memory
JTAG Connector
27
Cyclone
EP1C20
Device
Mictor Connector
Proto 1 Expansion
Prototype Header
1 Mbyte SRAM
Ethernet
MAC/PHY
RJ45
Connector
Compact Flash
Proto 2 Expansion
Prototype Header
Push-button
Switches [4]
41
4
8
RS-232
User LEDs [8]
16
Dual Seven-Segment Display
Altera Corporation
RS-232
11
Board Components
Nios
Development
Board
Components
Nios Development Board Reference Manual, Cyclone Edition
This section contains a brief overview of important components on the
Nios development board (see Figure 2). Links to the component
manufacturers are included when available.
A complete set of schematics, a physical layout database, and GERBER
files for the Nios development board are installed in the documents
directory for the Nios development kit.
Figure 2. Nios Development Board Components
12
Altera Corporation
Nios Development Board Reference Manual, Cyclone Edition
The Cyclone
EP1C20 Device
Board Components
U60 is a Cyclone EP1C20F400C7 device in a 400-pin FineLine BGA®
package. Table 4 lists the Cyclone device features.
Table 4. Cyclone EP1C20 Device Features
Logic Elements
M4K RAM blocks (128 X 36 bits)
Total RAM bits
PLLs
Maximum user I/O pins
20,060
64
294,912
2
301
The development board provides two separate methods for configuring
the Cyclone device:
f
Flash Memory
Device
Altera Corporation
1.
Using the Quartus II software running on a host computer, a
designer configures the device directly via an Altera download cable
connected to the Cyclone JTAG header (J24).
2.
When power is applied to the board, a configuration controller
device (U3) attempts to configure the Cyclone device with hardware
configuration data stored in flash memory. For more information on
the configuration controller, see “Configuration Controller Device
(EPM7128AE)” on page 28.
See the Altera Cyclone literature page for Cyclone-related documentation
at www.altera.com/literature/lit-cyc.html including a Cyclone EP1C20
pinout document.
U5 is an 8 Mbyte AMD AM29LV065D flash memory device connected to
the Cyclone device and can be used for two purposes:
1.
A Nios embedded processor implemented on the Cyclone device can
use the flash memory as general-purpose readable memory and nonvolatile storage.
2.
The flash memory can hold Cyclone configuration data that is used
by the configuration controller to load the Cyclone device at powerup. See “Configuration Controller Device (EPM7128AE)” on
page 28. for related information.
13
Board Components
Nios Development Board Reference Manual, Cyclone Edition
Hardware configuration data that implements the Nios reference design
is pre-stored in this flash memory. The pre-loaded Nios reference design,
once loaded, can identify the 8 Mbyte flash memory in its address space
and includes monitor software that can download files (either new
Cyclone configuration data, Nios embedded processor software, or both)
into flash memory. The Nios embedded processor software includes
subroutines for writing and erasing this specific type of AMD flash
memory.
The flash memory device shares address and data connections with the
SRAM chips and the Ethernet MAC/PHY chip. For shared bus
information, see“Appendix A: Shared Bus Table” on page 39.
f
Compact Flash
Connector
See www.amd.com for detailed information about the flash memory
device.
The compact flash connector (CON3) enables hardware designs to access
a compact flash card (see Figure 3). The following two access modes are
supported:
■
■
ATA (hot swappable mode)
IDE (IDE hard disk mode)
Figure 3. Compact Flash Connector
The IDE connection mode includes a power MOSFET which controls
power to the compact flash card. This MOSFET is controllable through an
IO pin on the Cyclone device.
1
14
The compact flash connector shares several Cyclone I/O pins
with expansion prototype connector header (PROTO1), see
“Expansion Prototype Connector (PROTO1)” on page 19 for
PROTO1 details.
Altera Corporation
Nios Development Board Reference Manual, Cyclone Edition
Board Components
Table 5 below provides compact flash pin out details
Table 5. Compact Flash (CON3) Pin Table (Part 1 of 2)
Altera Corporation
Cyclone Device
Pin (U60)
Compact Flash Pin
(CON3)
Compact Flash Function
GND
1
GND
F18
2
D03
E17
3
D04
D17
4
D05
D18
5
D06
C18
6
D07
H20
7
-CE
J15
8
A10
D13
9
-OE
J20
10
A09
H14
11
A08
J14
12
A07
VCC
13
VCC
J17
14
A06
J18
15
A05
K15
16
A04
W18
17
A03
H19
18
A02
H18
19
A01
H17
20
A00
F20
21
D00
F15
22
D01
E19
23
D02
H16
24
WP
GND
25
-CD2
B13
26
-CD1
F17
27
D11
E18
28
D12
F16
29
D13
F19
30
D14
G16
31
D15
-CE2
U19
32
GND
33
-VS1
G19
34
-OIORD
15
Board Components
Nios Development Board Reference Manual, Cyclone Edition
Table 5. Compact Flash (CON3) Pin Table (Part 2 of 2)
f
SDRAM Device
Cyclone Device
Pin (U60)
Compact Flash Pin
(CON3)
Compact Flash Function
G20
35
-IOWR
V18
36
-WE
G17
37
RDY/BSY
VCC
38
VCC
GND
39
-CSEL
NC
40
-VS2
RESET_n
41
RESET
G14
42
-WAIT
V19
43
-INPACK
U20
44
-REG
J16
45
BVD2
J19
46
BVD1
C19
47
D081
D19
48
D091
D20
49
D101
GND
50
GND
See www.molex.com for more compact flash connector (CON3)
information. See www.compactflash.org for more information on the
compact flash connector.
The SDRAM device (U57) is a Micron MT48LC4M32B2 chip with PC100
functionality and self refresh mode. The SDRAM is fully synchronous
with all signals registered on the positive edge of the system clock (clk).
The SDRAM device pins are connected to the Cyclone device (see Table 6).
An SDRAM controller peripheral is included with the Nios development
kit, allowing a Nios processor to view the SDRAM device as a large,
linearly addressable memory.
Table 6. SDRAM (U57) Pin Table (Part 1 of 3)
16
Pin Name
Pin Number
Connects to Cyclone Pin
A0
25
M2
A1
26
M1
A2
27
M6
A3
60
M4
Altera Corporation
Nios Development Board Reference Manual, Cyclone Edition
Board Components
Table 6. SDRAM (U57) Pin Table (Part 2 of 3)
Altera Corporation
Pin Name
Pin Number
Connects to Cyclone Pin
A4
61
J8
A5
62
J7
A6
63
J6
A7
64
J5
A8
65
J4
A9
66
J3
A10
24
H6
A11
21
H5
BA0
22
H7
BA1
23
H1
DQ0
2
M5
DQ1
4
M3
DQ2
5
M7
DQ3
7
N6
DQ4
8
N1
DQ5
10
N2
DQ6
11
N4
DQ7
13
N3
DQ8
74
N5
DQ9
76
N7
DQ10
77
P7
DQ11
79
P2
DQ12
80
P1
DQ13
82
P6
DQ14
83
P5
DQ15
85
P3
DQ16
31
P4
DQ17
33
R1
DQ18
34
R2
DQ19
36
R6
DQ20
37
R5
DQ21
39
R3
DQ22
40
R4
DQ23
42
T4
DQ24
45
T2
DQ25
47
T3
DQ26
48
U1
17
Board Components
Nios Development Board Reference Manual, Cyclone Edition
Table 6. SDRAM (U57) Pin Table (Part 3 of 3)
f
Dual SRAM
Devices
Pin Name
Pin Number
Connects to Cyclone Pin
DQ27
50
U4
DQ28
51
U2
DQ29
53
U3
DQ30
54
V3
DQ31
56
V2
DQM0
16
J2
DQM1
71
J1
DQM2
28
H4
DQM3
59
H3
RAS_N
19
H2
CAS_N
18
G3
CKE
67
G7
G6
CS_N
20
WE_N
17
G4
CLK
68
L13
See www.micron.com for detailed SDRAM information.
U35 and U36 are two (512 Kbyte x 16-bit) asynchronous SRAM devices.
They are connected to the Cyclone device so they can be used by a Nios
embedded processor as general-purpose memory. The two 16-bit devices
can be used in parallel to implement a 32-bit wide memory subsystem.
The pre-loaded Nios reference design identifies these SRAM devices in its
address space as a contiguous 1Mbyte, 32-bit-wide, zero-wait-state main
memory.
The SRAM devices share address and data connections with the flash
memory and the Ethernet MAC/PHY device. For shared bus information,
see “Appendix A: Shared Bus Table” on page 39.
f
Ethernet
MAC/PHY
18
See www.idt.com for detailed information about the SRAM devices.
The LAN91C111 (U4) is a mixed signal analog/digital device that
implements protocols at 10Mbps and 100 Mbps. The control pins of U4 are
connected to the Cyclone device so that Nios systems can access Ethernet
via the RJ-45 connector (RJ1). See Figure 4 on page 19. The Nios
development kit includes hardware and software components that allow
Nios processor systems to communicate with the LAN91C111 Ethernet
device.
Altera Corporation
Nios Development Board Reference Manual, Cyclone Edition
Board Components
Figure 4. Ethernet MAC/PHY Device
The Ethernet MAC/PHY device share address and data connections with
the flash memory and the SRAM chips. For shared bus information, see
“Appendix A: Shared Bus Table” on page 39.
f
Expansion
Prototype
Connector
(PROTO1)
See www.smsc.com for detailed information about the LAN91C111
device. See the Plugs Ethernet Library Reference Manual for details on
accessing the MAC/PHY device in Nios software.
The PROTO1 expansion prototype connectors share Cyclone IO pins with
the compact flash connector. Designs may use either the PROTO1
connectors or the compact flash.
Headers J11, J12, and J13 collectively form the standard-footprint,
mechanically-stable connection that can be used (for example) as an
interface to a special-function daughter card.
1
See the Altera web site for a list of available expansion daughter
cards that can be used with the Nios development board at
www.altera.com/devkits.
The expansion prototype connector interface includes:
■
■
■
■
■
■
■
41 I/O pins for prototyping. All 41 I/O pins connect to user I/O pins
on the Cyclone device. Each signal passes through analog switches
(U19, U20, U21, U22 and U25) to protect the Cyclone device from 5-V
logic levels. These analog switches are permanently enabled.
A buffered, zero-skew copy of the on-board OSC output from U2.
A buffered, zero-skew copy of the Cyclone's phase-locked loop
(PLL)-output from U60.
A logic-negative power-on reset signal
Five regulated 3.3-V power-supply pins (2A total max load for both
PROTO1 & PROTO2)
One regulated 5-V power-supply pin (1A total max load for both
PROTO1 & PROTO2)
Numerous ground connections
The output logic level on the expansion prototype connector pins is 3.3V.
The power supply included wit the Nios development kit cannot supply
the maximum load current specified above.
Altera Corporation
19
Board Components
Nios Development Board Reference Manual, Cyclone Edition
Figure 5, Figure 6 on page 20 and Figure 7 on page 21 show connections
from the PROTO1 expansion headers to the Cyclone device. Unless
otherwise noted, labels indicate Cyclone device pin numbers.
Figure 5. Expansion Prototype Connector - J11
Figure 6. Expansion Prototype Connector - J12
20
Altera Corporation
Nios Development Board Reference Manual, Cyclone Edition
Board Components
Figure 7. Expansion Prototype Connector - J13
Pin 1
J13
(1) Vunreg (U54 pin 2)
1
2
GND
NC
3
4
GND
+3.3V
5
6
GND
+3.3V
7
8
GND
(2) PROTO1_OSC(U2 pin 4)
9
10 GND
(3) PROTO1_CLKIN (U2 pin 18) 11
12 GND
(4) PROTO1_CLKOUT (K6) 13
14 GND
+3.3V 15
16 GND
+3.3V 17
18 GND
+3.3V 19
20 GND
Note to Figure 7
(1)
(2)
(3)
(4)
Expansion
Prototype
Connector
(PROTO2)
Unregulated voltage from AC to DC power transformer.
Clk from board oscillator.
Clk from PLD via buffer.
Clk output from protocard to PLD.
Headers J15, J16, and J17 collectively form the standard-footprint,
mechanically-stable connection that can be used (for example) as an
interface to a special-function daughter card.
The expansion prototype connector interface includes:
■
■
■
■
■
■
■
41 I/O pins for prototyping. All 41 I/O pins connect to user I/O pins
on the Cyclone device. Each signal passes through analog switches
(U27, U28, U29, U30 and U31) to protect the Cyclone device from 5-V
logic levels. These analog switches are permanently enabled.
A buffered, zero-skew copy of the on-board OSC output (from U2).
A buffered, zero-skew copy of the Cyclone's phase-locked loop
(PLL)-output (from U60)
A logic-negative power-on-reset signal
Five regulated 3.3-V power-supply pins (2A total max load for both
PROTO1 & PROTO2)
One regulated 5-V power-supply pin (1A total max load for both
PROTO1 & PROTO2)
Numerous ground connections
The output logic level on the expansion prototype connector pins is 3.3V.
The power supply included wit the Nios development kit cannot supply
the maximum load current specified above.
Altera Corporation
21
Board Components
Nios Development Board Reference Manual, Cyclone Edition
Figure 8 on page 22, Figure 9 on page 22 and Figure 10 on page 23 show
connections from the PROTO2 expansion headers to the Cyclone device.
Unless otherwise noted, labels indicate Cyclone device pin numbers.
Figure 8. Expansion Prototype Connector - J16
Figure 9. Expansion Prototype Connector - J15
22
Altera Corporation
Nios Development Board Reference Manual, Cyclone Edition
Board Components
Figure 10. Expansion Prototype Connector - J17
Pin 1
J17
(1) Vunreg (U54 pin 2)
1
2
GND
NC
3
4
GND
+3.3V
5
6
GND
+3.3V
7
8
GND
(2) PROTO2_OSC(U2 pin 6)
9
10 GND
(3) PROTO2_CLKIN (U2 pin 17) 11
12 GND
(4) PROTO2_CLKOUT (K14) 13
14 GND
+3.3V 15
16 GND
+3.3V 17
18 GND
+3.3V 19
20 GND
Note to Figure 10
(1)
(2)
(3)
(4)
Mictor
Connector
Unregulated voltage from AC to DC power transformer.
Clk from board oscillator.
Clk from PLD via buffer.
Clk output from protocard to PLD.
The Mictor connector (J25) can be used to transmit up to 27 high-speed
I/O signals with very low noise via a shielded Mictor cable. J25 is used as
a debug port. Twenty five of the Mictor connector signals are used as data,
and two signals are used as clock input and clock output.
Most Mictor connector pins on J25 connect to I/O pins on the Cyclone
device (U60). For systems that do not use the Mictor connector for the
Nios OCI debug module, any on-chip signals can be routed to I/O pins
and probed at J25 via a Mictor cable. External scopes and logic analyzers
can connect to J25 and analyze a large number of signals simultaneously.
1
f
Altera Corporation
The Nios OCI debug module is the First Silicon Solutions Inc.
(FS2) OCI core.
See the Nios Development Software Tutorial for the more information about
the OCI debug module.
23
Board Components
Nios Development Board Reference Manual, Cyclone Edition
Figure 11 on page 24 shows an example of an in-target system analyzer
ISA-NIOS/T (sold separately) by First Silicon Solutions (FS2) Inc. For
details see www.fs2.com.
Figure 11. Mictor Debug Port to OCI Debug Module
Five of the signals connect directly to the JTAG pins on the Cyclone device
(U60), and also connect directly to the Cyclone device’s JTAG connector
(J24). The JTAG signals have special usage requirements. You cannot use
J24 and J25 at the same time.
Figure 12 below shows connections from the Mictor connector to the
Cyclone device. Figure 13 on page 25 shows the pin out for J25. Unless
otherwise noted, labels indicate Cyclone device pin numbers.
Figure 12. Mictor Connector Signaling
24
Altera Corporation
Nios Development Board Reference Manual, Cyclone Edition
Board Components
Figure 13. Debug Mictor Connector - J25
Serial Port
Connectors
J19 & J27 are standard DB-9 serial connectors. These connectors are
typically used for communication with a host computer using a standard,
9-pin serial cable connected to (for example) a COM port. Level-shifting
buffers (U52 and U58) are used between J19 & J27 and the Cyclone device,
because the Cyclone device cannot interface to RS-232 voltage levels
directly.
The Nios development board provides two serial connectors, one labeled
Console and the other labeled Debug. Many processor systems make use
of multiple UART communication channels during prototype and debug
stages.
The console serial port is able to transmit all RS-232 signals. Alternately,
the Cyclone design may use only the signals it needs, such as RXD and
TXD. LEDs are connected to the RXD and TXD signals, giving a visual
indication when data is being transmitted or received. Figure 14 and
Figure 15 show the pin connections between the Console and Debug serial
connectors and the Cyclone device.
Figure 14. Console Serial Port Connector - J19
Altera Corporation
25
Board Components
Nios Development Board Reference Manual, Cyclone Edition
Figure 15. Debug Serial Port Connector – J27
Dual
7-Segment
Display
U8 and U9 are connected to the Cyclone device so that each segment is
individually controlled by a general-purpose I/O pin. When the Cyclone
pin drives logic 0, the corresponding LED turns on. See Figure 16 for
Cyclone device pin out details.
Figure 16. Dual-7-Segment Display
The pre-loaded Nios reference design includes parallel input/output
(PIO) registers and logic for driving this display.
Push-Button
Switches
SW0 – SW3 are momentary-contact push-button switches that provide
stimulus to designs in the Cyclone device. See Figure 17 on page 27. Each
switch is connected to an Cyclone general-purpose I/O pin with a pull-up
resistor as shown in Table 7. The Cyclone device pin will see a logic 0
when each switch is pressed.
Table 7. Push Button Switches Pin Out Table
26
Button
SW0
SW1
SW2
SW3
Cyclone Pin
W3
Y4
V4
W4
Altera Corporation
Nios Development Board Reference Manual, Cyclone Edition
Individual LEDs
Board Components
This Nios development board provides eight individual LEDs connected
to the Cyclone device. See Figure 17 on page 27. D0 – D7 are connected to
general purpose I/O pins on the Cyclone device as shown in Table 8.
When the Cyclone pin drives logic 1, the corresponding LED turns on.
Table 8. LED Pin Out Table
LED
D0
D1
D2
D3
D4
D5
D6
D7
Cyclone Pin
E14
E13
C14
D14
E12
F12
B3
B14
Figure 17. SW0 – SW3 Push Button Switches and Individual LEDs
Serial
Configuration
Device (EPCS4)
Serial configuration devices are flash memory devices with a serial
interface that can store configuration data for a Cyclone device and reload
the data to the device upon power-up or re-configuration. With the new
data-decompression feature in the Cyclone FPGA family, designers can
use smaller serial configuration devices to configure larger Cyclone
FPGAs. Serial configuration devices cannot be cascaded.
The SOPC Builder active serial memory interface component allows
microprocessor systems access to serial configuration memory.
Serial Flash
Connector
The serial flash connector logic is designed strictly for an EPCS4 serial
configuration device connection. Hardware designers will never need the
serial flash connector for using the reference designs that came with the
Nios development kit. The reference designs allow the designer to access
data from the serial configuration device without using this connector. See
“Cyclone Configuration” on page 28.
1
f
Altera Corporation
The ByteBlaster II download cable is required when using the
serial flash connector for connecting to the EPCS4 serial
configuration device.
See the Serial Configuration Devices (EPCS1 & EPCS4) Data Sheet at for more
information about this device and the Active Serial Memory Interface Data
Sheet for information about the active serial memory interface component
in SOPC Builder.
27
Board Components
Configuration
Controller
Device
(EPM7128AE)
Nios Development Board Reference Manual, Cyclone Edition
The configuration controller (U3), is an Altera EPM7128AE device. It
comes pre-programmed with logic for managing board reset conditions
and configuring the Cyclone device from data stored in flash memory and
the EPCS4 serial configuration device.
Reset Distribution
The EPM7128AE takes a power-on reset pulse from the Linear
Technologies 1326 power-sense/reset-generator chip and distributes it
(through internal logic) to other reset-pins on the board, including the:
■
■
■
LAN91C111 (Ethernet MAC/PHY) reset
Flash memory reset
Reset signals delivered to the expansion prototype connector headers
(PROTO1 & PROTO2)
Starting Configuration
There are four methods to start a configuration sequence. The four
methods are the following:
1.
Board power-on.
2.
Pressing the Reset, Config button (SW10).
3.
Asserting (driving 0 volts on) the MAX's reconfigreq_n input pin
(from a Cyclone design).
4.
Pressing the Force Safe button (SW9).
Cyclone Configuration
At power-up or reset, the configuration controller attempts to configure
the Cyclone device with data from one of three sources, in the following
order:
■
■
■
First—The EPCS4 serial configuration device
Second—The User configuration from flash memory
Third—The Safe configuration from flash memory
First, the configuration controller puts the Cyclone FPGA in active serial
(AS) configuration mode. The Cyclone FPGA will then attempt to read
configuration data from the EPCS4. If the Cyclone FPGA is successfully
configured, the configuration controller stops.
28
Altera Corporation
Nios Development Board Reference Manual, Cyclone Edition
Board Components
If configuration from the EPCS4 was not successful, the configuration
controller puts the Cyclone FPGA into passive serial mode and attempts
to load the user configuration from flash memory. If this also fails, the
configuration controller attempts to load the safe configuration in flash
memory.
When SW9 (Force Safe) is pressed, the configuration controller
immediately begins configuring the Cyclone FPGA from the safe
configuration in flash memory—data in the EPCS4 and in the User
Hardware Image are ignored.
Most users will never need to re-program the configuration controller.
Reprogramming the configuration controller may result in an inoperable
development board. A programming file (config_controller.pof) with the
original configuration controller logic is included with the Nios
development kit. If you have changed the MAX device logic, you can
restore the factory configuration using this programming file located in
the EPM7128_flash_config_ controller folder of the examples directory
for this board.
See the MAX7000 device literature at www.altera.com/literature/litm7k.html for detailed information about the Altera EPM7128AE device
(Altera MAX® 7000 family).
Configuration Data
The Quartus II software can (optionally) produce hexout configuration
files that are directly suitable for download and storage in the flash
memory as configuration data. A hexout configuration file for the Cyclone
EP1C20 device (U60) is a little less than 1 Mbyte, and occupies about one
eighth of the flash memory (U5).
New hexout files can be stored in the flash memory (U5) by software
running on a Nios embedded processor. The Nios pre-loaded reference
design includes facilities for downloading hexout files from a host (such
as desktop workstation) into flash memory.
f
Altera Corporation
See the Nios Embedded Processor Software Development Reference Manual for
detailed information.
29
Board Components
Nios Development Board Reference Manual, Cyclone Edition
Safe and User Configurations
The configuration controller can manage three separate Cyclone device
configurations: one configuration stored in the EPSC4 configuration
device, and two configurations stored in flash memory. These two
configurations stored in flash memory are conventionally referred to as
the safe configuration and the user configuration.
The configuration controller expects user configuration and safe
configuration files to be stored at fixed locations (offsets) in flash memory.
Table 10 on page 32 shows how the configuration controller expects flash
memory contents to be arranged.
1
A Nios reference design is pre-loaded into the safe-configuration
region of the flash memory. Altera recommends that users avoid
overwriting the safe configuration data.
If SW9 (Force Safe) is pressed, the configuration controller will ignore the
user-configuration and always configure the Cyclone device from the safe
configuration. This switch allows you to “escape” from the situation
where a valid-but-nonfunctional user configuration is present in flash
memory or the serial configuration device.
f
See the Nios Embedded Processor Software Development Reference Manual for
detailed information about downloading and relocating files using the
GERMS monitor.
Using Conventional Flash Memory
The Nios Development Board includes an 8 MByte flash memory device
(U5). See Table 9. It is divided into 128 individually-erasable 64K sectors.
This web-server design, and (more importantly) the on-board
configuration controller, makes certain assumptions about what–resides–
where in flash memory.
30
Altera Corporation
Nios Development Board Reference Manual, Cyclone Edition
Board Components
Each of the upper four (4) MBbytes of flash memory are used by either the
configuration controller or the web server. Your application software may
safely use the lower half (4 MBytes) of flash memory without interfering
with FPGA configuration or web-server operation.
Table 9. Flash Memory Allocation
Address (hex)
000000
Flash Allocation
4MB
100000
200000
300000
400000
Web Pages (2MB)
500000
600000
User Configuration Data (1 MB)
700000
Safe Configuration Data (1 MB)
Factory-programmed–do not erase
1
w
Available for user data.
The factory-programmed reference design implements a web
server. Network settings and web pages are pre-programmed in
the flash memory, as shown in Table 10 on page 32.
WARNING: The safe example design is provided for reference
only. Do not base your hardware or software designs on the safe
example design. Use the standard_32 example design.
User Hardware Image
At power on, or when the Reset, Config button (SW10) is pressed, the
configuration controller begins reading user configuration data out of
flash at address 0x600000. This data, and suitable control signals, are used
in an attempt to configure the FGPA. FPGA configuration data written
into this region of flash memory is conventionally called the User
Hardware Image. The web server includes documentation on how to
create your own User Hardware Image data and several facilities for
burning your User Hardware Image into flash memory.
Altera Corporation
31
Board Components
Nios Development Board Reference Manual, Cyclone Edition
Safe Hardware Image
If there is no valid User Hardware Image, or if SW9 (Force Safe) is
pressed, the configuration controller begins reading data out of flash at
address 0x700000. Any FPGA configuration data stored at this location is
conventionally called the Safe Hardware Image. Your development
board was factory-programmed with a Safe Hardware Image, plus
additional data located in the range 0x700000-0x7FFFFF, as shown in
Table 10. The design used for the Safe Hardware Image is the safe
example design found in the examples directory.
The configuration controller will stop reading data when the FPGA
successfully configures. The safe example design is setup to begin
executing code from address 0x7B0000. This region of flash memory is
programmed with the web-server application software.
1
Do Not Erase your Safe Hardware Image (safe hardware
configuration data). If you do so inadvertently, see “Appendix B:
Restore the Factory Configuration” on page 43 for instructions
on how to restore your board to its factory configuration.
Table 10. Safe Hardware Configuration Data Memory Allocation
Address (hex)
Safe Hardware Image
700000
FPGA Configuration Data
710000
720000
730000
740000
750000
760000
770000
780000
790000
7A0000
7B0000
Web Server Software
7C0000
7D0000
7E0000
7F0000
32
Network Settings
Altera Corporation
Nios Development Board Reference Manual, Cyclone Edition
Board Components
The Configuration-Status LEDs
The MAX device is connected to four status LEDs that show the
configuration status of the board at a glance (see Figure 18). The user can
tell which configuration, if any, was loaded into the board at power-on by
looking at the LEDs (see Table 11 on page 33). If a new configuration was
downloaded into the Cyclone device via JTAG, then all of the LEDs will
turn off.
Figure 18. LED1 – LED4
Table 11. Configuration Status LED Indicators
LED
LED Name
Color
Description
LED3
Loading
Green
LED4
Error
Red
If the red Error LED is on, then configuration was NOT transferred from
flash memory into the Cyclone device. This can happen if, for example, the
flash memory contains neither a valid user or safe configuration.
LED1
User
Green
If the Cyclone device was successfully configured with data from the
EPCS4, LED1 will blink slowly. If the Cyclone device was successfully
loaded with the user configuration from flash memory, LED1 will remain on
continuously.
LED2
Force Safe
Amber
This LED turns on when the safe configuration is being transferred from
flash memory and stays illuminated if the safe configuration was
successfully loaded into the Cyclone device.
This LED blinks while the MAX configuration-controller is actively
transferring data from flash memory into the Cyclone FPGA.
Configuration and Reset Buttons
The Nios development board uses dedicated switches SW8, SW9 and
SW10 for the following fixed functions:
Altera Corporation
33
Board Components
Nios Development Board Reference Manual, Cyclone Edition
SW8 – CPU Reset
When SW8 is pressed, a logic-0 is driven onto the Cyclone devices'
DEV_CLRn pin (and user I/O C_4). The result of pressing SW8 depends
on how the Cyclone device is currently configured.
The pre-loaded Nios reference design treats SW8 as a CPU-reset pin (see
Figure 19). The reference Nios CPU will reset and start executing code
from its reset address when SW8 is pressed.
Figure 19. Safe Config Button
SW9 – Force Safe
Pressing Force Safe (SW9) commands the configuration controller to reconfigure the Cyclone device with the factory-programmed safe
configuration.
SW10 – Reset, Config
Reset, Config (SW10) is the power-on reset button (see Figure 20). When
SW10 is pressed, a logic 0 is driven to the power-on reset controller (U18).
See “Power-Supply Circuitry” on page 35 for more details. After SW10 is
pressed, the configuration controller will load the Cyclone device from
flash memory. See “Configuration Controller Device (EPM7128AE)” on
page 28 for more information.
SW10
Figure 20. Reset, Config Button
Reset
Config
34
Altera Corporation
Nios Development Board Reference Manual, Cyclone Edition
Power-Supply
Circuitry
The Nios development board runs from a 9-V, unregulated, centernegative input power supply. On-board circuitry generates 5-V, 3.3-V,
and 1.5-V regulated power levels.
■
■
■
Clock Circuitry
Board Components
The 5-V supply is present on pin 2 of J12 and J15 for use by any device
plugged into the PROTO1 or PROTO2 expansion connectors.
The 3.3-V supply is used as the power source for all Cyclone device
I/O pins. The 3.3-V supply is also available to PROTO1 &PROTO2
daughter cards.
The 1.5-V supply is used only as the power supply for the Cyclone
device core (VCCint) and it is not available on any connector or
header.
The Nios development board includes a 50 MHz free-running oscillator
and a zero-skew, point-to-point clock distribution network. The clock
network drives the Cyclone device and pins on the expansion prototype
connectors, the configuration controller device, and the Mictor connector.
The zero-skew buffer distributes both the free-running 50 MHz clock and
the clock-output from one of the Cyclone's device internal PLLs
(CLKLK_OUT1). See Figure 21.
Figure 21. Clock Circuitry
Note to Figure 21:
(1)
An external clock can be enabled by stuffing location R15 with a 49.9 ohm 0603 resistor and stuffing location R13
with a 330 ohm 0603 resistor.
Altera Corporation
35
Board Components
Nios Development Board Reference Manual, Cyclone Edition
A socketed 50 MHz free-running oscillator (Y2) supplies the fundamental
operating frequency, and a clock buffer (U2) drives zero-skew clock
signals to various points on the board.
The Cyclone device can synthesize a new clock signal internally using onchip PLLs, and distribute the clock to various locations on the board by
outputting the clock signal to the IO_PLL1_OUT0_p pin. The clock buffer
drives this signal to the following locations:
■
■
■
The PROTO1_CLKIN and PROTO2_CLKIN pins on the expansion
prototype connectors, allowing a user-defined clock to drive each of
the expansion prototype headers.
The clock input for the SDRAM memory (U57), allowing SDRAM to
run at a different rate than the clock oscillator.
The CLK0 clock input on the Cyclone device.
The Cyclone device can also supply a clock from the IO_PLL2_OUT0_p
pin to the SDRAM (U57).
1
JTAG
Connections
The 50 MHz oscillator (Y2) is socketed and can be changed by the
user. However, the MAX EPM7128AE device configuration
control circuit and other Altera reference designs are not
guaranteed to work at different frequencies. It is the user’s
responsibility to accommodate a new clock oscillator when
designing a system.
The Nios development board, has two 10-pin JTAG headers (J5 and J24)
compatible with the Altera ByteBlaster II download cable. Each JTAG
header connects to one Altera device and forms a single-device JTAG
chain. J24 connects to the Cyclone device (U60), and J5 connects to the
MAX EPM7128AE device (U3).
JTAG to Cyclone Device (J24)
J24 connects to the JTAG pins (TCK, TDI, TDO, TMS, TRST) of the Cyclone
device (U60) as shown in Figure 22 on page 37. Altera Quartus II software
can directly configure the Cyclone device with a new hardware image via
an Altera ByteBlaster II download cable as shown in Figure 23 on page 37.
In addition, Nios embedded processor debugger software can access the
Nios OCI debug module via a download cable connected to the J24 JTAG
connector.
36
Altera Corporation
Nios Development Board Reference Manual, Cyclone Edition
Board Components
Figure 22. JTAG Connector (J24) to Cyclone Device
To Mictor Connector (J25)
JTAG signals
JTAG Connector
(J24)
Cyclone Device
(U53)
TDI
TMS
TCK
TDO
TRST
Figure 23. JTAG Connection to Download Cable
Pin 1
J24
The Cyclone device’s JTAG pins can also be accessed via the Mictor
connector (J25). The pins of J24 are connected directly to pins on J25, and
care must be taken so that signal contention does not occur between the
two connectors.
Altera Corporation
37
Board Components
Nios Development Board Reference Manual, Cyclone Edition
JTAG to MAX Device (J5)
J5 connects to the JTAG pins (TCK, TDI, TDO, TMS, TRST) of the MAX
device (U3) as shown in Figure 24. Altera Quartus II software can perform
in-system programming (ISP) to reprogram the MAX device (U3) with a
new hardware configuration via an Altera ByteBlaster II download cable.
Figure 24. JTAG Connector (J5) to MAX Device
Pin 1
J5
38
Altera Corporation
Appendix A:
Shared Bus Table
On the Nios Development Board, Cyclone Edition, the flash memory, SRAM and Ethernet
MAC/PHY devices share address and control lines. These shared lines are referred to as the Shared
Bus. Using SOPC Builder, designers can interface a Nios processor system to any device connected
to the off-chip shared bus.
Altera Corporation
Appendix A
Table 12 on page 40 lists all connections between the devices connected to the shared bus.
2
39
Shared Bus Table
Nios Development Board Reference Manual, Cyclone Edition
Table 12. Shared Bus Table (Part 1 of 3)
NET Name
NET
Description
PLD (U60)
Pin Pin #
Na
me
Flash (U5)
Pin
Name
Pin #
27
SRAM (U35)
SRAM (U36)
Ethernet (U4)
Pin
Pin # Pin
Pin # Pin Name
Name
Name
Pin #
IO
B4
A0
IO
A4
A1
22
A1
78
FSE_A2
IO
D5
A2
21
A0
1
A0
1
A2
79
FSE_A3
IO
D6
A3
20
A1
2
A1
2
A3
80
FSE_A4
IO
C5
A4
19
A2
3
A2
3
A4
81
FSE_A5
IO
B5
A5
18
A3
4
A3
4
A5
82
FSE_A6
IO
C2
A6
17
A4
5
A4
5
A6
83
FSE_A7
IO
D2
A7
16
A5
18
A5
18
A7
84
FSE_A8
IO
D4
A8
10
A6
19
A6
19
A8
85
FSE_A9
IO
D1
A9
9
A7
20
A7
20
A9
86
FSE_A10
IO
E4
A10
42
A8
21
A8
21
A10
87
FSE_A11
IO
E5
A11
8
A9
22
A9
22
A11
88
FSE_A12
IO
F3
A12
7
A10
23
A10
23
A12
89
FSE_A13
IO
E3
A13
6
A11
24
A11
24
A13
90
FSE_A14
IO
E2
A14
5
A12
25
A12
25
A14
91
FSE_A15
IO
F4
A15
4
A13
26
A13
26
A15
92
FSE_A16
IO
F5
A16
3
A14
27
A14
27
FSE_A17
IO
F2
A17
46
A15
42
A15
42
FSE_A18
IO
F1
A18
15
A16
43
A16
43
FSE_A19
IO
F6
A19
43
A17
44
A17
44
FSE_A20
IO
G5
A20
44
FSE_A21
IO
G1
A21
35
FSE_A22
IO
G2
A22
2
FSE_A0
FSE_A1
40
Shared
Address
Altera Corporation
Nios Development Board Reference Manual, Cyclone Edition
Shared Bus Table
Table 12. Shared Bus Table (Part 2 of 3)
NET Name
Flash (U5)
SRAM (U35)
IO
C6
D0
31
D0
7
D0
107
FSE_D1
IO
E6
D1
32
D1
8
D1
106
FSE_D2
IO
B6
D2
33
D2
9
D2
105
FSE_D3
IO
A6
D3
34
D3
10
D3
104
FSE_D4
IO
F7
D4
38
D4
13
D4
102
FSE_D5
IO
E7
D5
39
D5
14
D5
101
FSE_D6
IO
B7
D6
40
D6
15
D6
100
FSE_D7
IO
A7
D7
41
D7
16
D7
99
FSE_D8
IO
D7
D8
29
D8
76
FSE_D9
IO
C7
D9
30
D9
75
FSE_D10
IO
F8
D10
31
D10
74
FSE_D11
IO
E8
D11
32
D11
73
FSE_D12
IO
B8
D12
35
D12
71
FSE_D13
IO
A8
D13
36
D13
70
FSE_D14
IO
D8
D14
37
D14
69
FSE_D15
IO
C8
D15
38
D15
68
FSE_D16
IO
B9
D16
66
FSE_D17
IO
A9
D1
8
D17
65
FSE_D18
IO
D9
D2
9
D18
64
FSE_D19
IO
C9
D3
10
D19
63
FSE_D20
IO
E9
D4
13
D20
61
FSE_D21
IO
E10
D5
14
D21
60
FSE_D22
IO
B10
D6
15
D22
59
FSE_D23
IO
A10
D7
16
D23
58
FSE_D24
IO
F10
D8
29
D24
56
FSE_D25
IO
C10
D9
30
D25
55
FSE_D26
IO
D10
D10
31
D26
54
FSE_D27
IO
C11
D11
32
D27
53
FSE_D28
IO
D11
D12
35
D28
51
FSE_D29
IO
B11
D13
36
D29
50
FSE_D30
IO
A11
D14
37
D30
49
FSE_D31
IO
E11
D15
38
D31
48
Altera Corporation
Shared Data
SRAM (U36)
D0
7
Ethernet (U4)
41
2
Appendix A
PLD (U60)
FSE_D0
NET
Description
Shared Bus Table
Nios Development Board Reference Manual, Cyclone Edition
Table 12. Shared Bus Table (Part 3 of 3)
NET Name
NET
Description
PLD (U60)
Flash (U5)
SRAM (U35)
SRAM (U36)
Ethernet (U4)
FLASH_CS_n
Chip Select
IO
A12
CE_n
28
FLASH_OE-N
Read Enable
IO
B12
OE_n
30
FLASH_RW-N
Write Enable
IO
D12
WE_n
11
FLASH_RY-BY_N
Ready/Busy
IO
C12 RY/BY_n
SRAM_BE_N0
Byte Enable 0
IO
V17
BE0#
39
SRAM_BE_N1
Byte Enable 1
IO
V16
BE1#
40
SRAM_BE_N2
Byte Enable 2
IO
W16
BE2#
39
SRAM_BE_N3
Byte Enable 3
IO
T16
BE3#
40
SRAM_CS_N
Chip Select
IO
W17
CS_n
6
CS_n
6
SRAM_OE_N
Read Enable
IO
Y17
OE_n
41
OE_n
41
SRAM_WE_N
Write Enable
IO
U16
WE_n
17
WE_n
17
ENET_ADS_N
Address Strobe
IO
A14
ADS#
37
ENET_AEN
Address Enable
IO
B15
AEN
41
ENET_BE_N0
Byte Enable 0
IO
C16
BE0#
94
ENET_BE_N1
Byte Enable 1
IO
B16
BE1#
95
ENET_BE_N2
Byte Enable 2
IO
D16
BE2#
96
ENET_BE_N3
Byte Enable 3
IO
E16
BE3#
97
ENET_CYCLE_N
Bus Cycle
IO
B17
CYCLE#
35
ENET_DATACS_N
Data Chip
Select
IO
C15
DATACS#
34
ENET_INTRQ0
Interrupt
IO
D15
INTRO
29
ENET_IOCHRDY
IO Char Ready
IO
F14
ARDY
38
ENET_IOR_N
Read
IO
A15
RD#
31
ENET_IOW_N
Write
IO
E15
WR#
32
ENET_LCLK
Local Bus
Clock
IO
C17
LCLK
42
ENET_LDEV_N
Local Device
IO
D3
LDEV#
45
ENET_RDYRTN_N Ready Return
IO
B18
RDYRTN#
46
ENET_W_R_N
IO
A17
W/R#
36
42
Write/Read
14
Altera Corporation
Appendix B: Restore the
Factory Configuration
The Nios development board can always be restored to its factoryprogrammed configuration. To restore the factory configuration, you
must reprogram the flash memory on the Nios development board.
Reprogramming the flash memory requires the following:
■
■
Configuring the
Cyclone Device
A Nios processor hardware design configured in the Cyclone device
and executing the GERMS monitor.
The factory flash image for GERMS to program into the flash
memory.
With the above mentioned requirements, perform the following steps:
Connect the Nios development board to the host computer using the
ByteBlasterII download cable.
2.
Launch the Quartus II software and open the Programmer window
(Tools menu).
3.
Click Add File... and select the following configuration file:
<Nios Development Kit <install directory>/examples/
recovery_configuration_cyclone_1c20.sof
4.
In the Programmer window, check the Program/Configure box, and
click Start to download the hardware configuration.
5.
After configuration completes, hold down SW0, press and release
SW8 and then release SW0.
The Cyclone device is configured with a Nios processor hardware design
executing the GERMS monitor. At this stage, DO NOT push the Force Safe
or Reset, Config buttons, because it will reset the Cyclone configuration.
f
Altera Corporation
See the Nios Hardware Development Tutorial for a detailed description of
configuring the Cyclone device using the Quartus II software.
43
3
Appendix B
1.
Restore the Factory Configuration
Reprogramming
the Flash
Memory
Nios Development Board Reference Manual, Cyclone Edition
You can now use the Nios processor in the Cyclone device and the
GERMS monitor to reprogram the flash memory by performing the
following steps:
1.
Connect the Console RS-232 serial connector to the host computer
using a serial cable.
2.
Open a Nios SDK Shell by choosing Programs > Altera > Nios
Development Kit <installed version> Nios SDK Shell (Start menu).
The default flash image file is located in the Nios SDK Shell default
directory.
3.
To download the flash file to the GERMS monitor executing on the
board, type:
nios-run -x -r -p com1 default_board_image_cyclone_1c20.flash
This command assumes the you connected the serial cable to COM1
on your host computer. If you are using a different COM port,
change the com1 argument appropriately.
4.
It will take 10 to 20 minutes to download the entire flash image. Do
not reset the board during this time. When the download is
complete, the Nios SDK Shell will return to a bash prompt.
5.
Push the Force Safe button to perform a power-on reset and
reconfigure the Cyclone device from flash memory. You should see
the Safe LED turned on and activity on LEDs D0 — D7.
Your board is now re-configured to the default factory condition.
44
Altera Corporation
Appendix C: Board
Ethernet Connection
The default reference design shipped on the Nios development board
implements a web server, among other functions. The Ethernet port
provides a very fast and easy method to download hardware and
software images to the board via a web browser on your host computer.
The software reference design implements a web server on the Ethernet
port as soon as the board powers up and configures with the factoryprogrammed safe configuration. The web server responds to any HTTP
requests, regardless of origin, that arrive on its Ethernet connection.
This section assumes that you are familiar with the Nios SDK shell, the
nios-run utility for serial communication with the Nios development
board, and the GERMS monitor.
f
See the Nios Embedded Processor Software Development Reference Manual for
information on these topics.
Connecting the Ethernet Cable
The Nios Development Kit includes an Ethernet (RJ45) cable and a
male/female RJ45 crossover adapter. Before you connect these
components, you must decide how you want to use the network features
of your board. Select one of the two following connection methods:
Altera Corporation
Point-to-Point Connection — To use your Nios Development Board
connected directly to a host computer point-to-point (not on a LAN),
do the following:
a.
Connect one end of your RJ45 cable to the female socket in the
crossover adapter.
b.
Insert the male end of the crossover adapter into RJ1 on the Nios
Development Board.
c.
Connect the other end of the RJ45 connector directly to the
network (Ethernet) port on your host computer (see Figure 25).
45
4
Appendix C
1.
Board Ethernet Connection
Nios Development Board Reference Manual, Cyclone Edition
Figure 25. Point-to-Point Connection
2.
LAN Connection — To use your Nios development board on a LAN (for
example, connecting to an Ethernet hub) do the following:
a.
Connect one end of the RJ45 cable to the Ethernet connector on
the development board (RJ1).
b.
Connect the other end to your LAN connection (hub, router, wall
plug, etc.).
Connecting the LCD Display
Your Nios Development Kit was delivered with a two-line x 16-character LCD
text display. The web-server software displays useful status and progress
messages on this display. If you wish to use the network features of the
board, connect the LCD display to the Expansion Prototype Header J12 as
shown in Figure 26 (take special care of the location of pin 1).
Figure 26. Expansion Prototype Header - J12
Obtaining an IP address: DHCP
In order to function on a network (either a point–to–point or LAN), your
board must have an IP address. Upon reset, the web-server will attempt
to acquire an IP address via the DHCP protocol. Many LANs support
DHCP.
1
46
If you do not know whether or not your LAN supports DHCP,
it’s probably best to try DHCP first.
Altera Corporation
Nios Development Board Reference Manual, Cyclone Edition
Board Ethernet Connection
The board will continue to attempt DHCP self-configuration for one full
minute. You can tell whether DHCP has succeeded, or is still in progress,
by reading status-messages on the LCD display. If your LAN does not
support DHCP, or if you are using the point-to-point option above, then
DHCP configuration will ultimately fail.
You can stop the DHCP process at any time by pressing push button
switch SW3. Sending an exclamation point (!) to the board on the console
serial port will also immediately terminate DHCP configuration.
If DHCP succeeds, the board will display a success message on the LCD
display. It will also continuously display its IP address.
If DHCP fails (or is aborted), the board will obtain its IP address from flash
memory. All boards are delivered from the factory with the IP address
10.0.0.51. You can change the IP address using commands sent via the
console serial port (see “IP Addresses for Point–to–Point Connections”
below).
IP Addresses for Point–to–Point Connections
Your host computer and the development board are the only two devices
connected to a very simple (one-wire) network. When the board is
delivered from the factory, it is pre-programmed with the default IP
address 10.0.0.51. (The 10.0.0.x subnet is conventionally reserved for
development, testing, and prototyping.) For most operating systems, it
will be necessary to assign your host computer an IP address on this same
subnet.
Upon reset, the board will power-up and attempt DHCP selfconfiguration. On a point–to–point network, you should abort DHCP by
pressing SW3. If you frequently use your board in a point–to–point
configuration, you may wish to disable DHCP entirely by typing the
command: xdhcp:off to the console serial port.
Altera Corporation
47
4
Appendix C
For example, the address 10.0.0.1 will work fine. Your computer and your
development board are the only two devices connected on this simple
network, so it is not necessary to get an address assigned to you by your
system administrator. Any address in the 10.0.0.x subnet will work and
there is no possibility of conflicting with another device on the network.
You do, however, need the ability to change the IP address of your host
computer. On Windows machines, this is accomplished through the
Network Connections control panel.
Board Ethernet Connection
Nios Development Board Reference Manual, Cyclone Edition
IP Addresses for LAN Connections
If your LAN does not support DHCP, or if DHCP self configuration failed, then
you will need to assign your board a fixed IP address before you can access
it over a network. All boards arrive with a default IP address of 10.0.0.51.
(The 10.0.0.x subnet is conventionally reserved for development, test, and
prototyping.) You need to obtain a safe IP address in your LAN's subnet
from your system administrator.
Once you have obtained a safe IP address, you can assign it to your board
using GERMS commands over the serial connection. The GERMS monitor
in the default software reference design has been extended to implement
the xip command. The xip command sets the IP address for your board,
and saves this address in flash memory. In general, you will only need to
assign an IP address to your board once. However, you may change it at
any time by issuing another xip command.
For example, to assign the IP address 137.57.136.165, you would type the
following command at the GERMS + prompt:
xip:137.57.136.165 (no spaces)
1
The GERMS monitor does not recognize the Backspace key or
Delete key. If you make a mistake typing, press the Escape key to
get a fresh GERMS prompt and re-enter the command. To read
back the IP address, you can use the xip command with no colon
or arguments. To activate the new IP address, you must reset
your board by pushing the Force Safe button or the Reset, Config
button.
Browsing your Board
Once your board has a valid IP address (obtained from either DHCP self
configuration or from flash memory), you can access the board via a web
browser (e.g., Microsoft Internet Explorer). The board serves a website
which includes both extensive documentation and useful networkdownload utility functions. To browse this site, open a web browser and
type the IP address of the board (four numbers separated by decimalpoints) as a URL directly into the browser’s Address input field. You can
determine your board’s IP address by reading the messages displayed on
the LCD display (the IP address is continuously displayed) or by typing
xip on the Console Serial Port.
f
48
Extensive additional information on the board’s network
communications and download utilities are available via this web
interface.
Altera Corporation
Index
A
D
Appendix A
Shared bus table 39
Appendix B
Restore the factory configuration 43
Appendix C
Board Ethernet connection 45
Development board
Component illustration 12
Features 9
General description 9
Dual 7-segment display 26
U8 & U9 pin information 26
Dual SRAM devices 18
B
E
Block diagram 11
Board Ethernet connection
Browse the board 48
Connecting the Ethernet cable 45
Connecting the LCD display 46
Obtaining an IP address - DHCP 46
LAN connections 48
Point-to-point connections 47
C
Altera Corporation
F
Flash memory allocation 31
Flash memory device 13
I
Individual LEDs (D0 - D7) 27
Pin information 27
5
J
JTAG connections 36
JTAG to Cyclone device (J24) 36
JTAG to MAX device (J5) 38
Index
Clock circuitry 35
Compact flash connector 14
Configuration and reset buttons 33
SW10 - Reset config 34
SW8 - CPU reset 34
SW9 - Safe config 34
Configuration controller device 28
Configuration data 29
Configuration-status LEDs 33
Cyclone configuration 28
Reset distribution 28
Safe and user configurations 30
Starting configuration 28
Configuration-status LEDs
Indicators 33
Conventional flash memory usage 30
Cyclone EP1C20 device 13
Ethernet PHY/MAC 19
Expansion connector header (PROTO1) 19
J11 pin information 20
J12 pin information 21
J13 pin information 21
Expansion connector header (PROTO2) 21
J15 pin information 23
J16 pin information 22
J17 pin out information 23
49
Index
Nios Development Board Reference Manual, Cyclone Edition
M
Mictor connector 23
Debug port to OCI debug module 24
J25 pin information 25
P
Power-supply circuitry 35
Push-button switches 26
pin information 26
R
Reference design
default 9
restoring 10
Restore factory configuration
Configuring the Cyclone device 43
Reprogramming flash memory 44
S
Schematics 12
SDRAM device 16
Serial configuration device 27
Serial flash connector 27
Serial port connectors 25
Console
J19 pin information 25
Debug
J27 pin information 26
SRAM devices 18
SW10 button 34
SW8 button 34
SW9 button 34
50
Altera Corporation