Parallel Flash Loader IP Core User Guide 2015.06.15 UG-01082 Send Feedback Subscribe This document describes how to instantiate the Parallel Flash Loader (PFL) IP core in your design, programming flash memory, and configuring your FPGA from the flash memory. FPGAs’ increasing density requires larger configuration storage. If your system contains a flash memory device, you can use your flash memory as the FPGA configuration storage as well. You can use the PFL IP core in Altera® MAX® Series (MAX II, MAX V and MAX 10 devices) or all other FPGAs to program flash memory devices efficiently through the JTAG interface and to control configuration from the flash memory device to the Altera FPGA. Features Use the PFL IP core to: • Program Common Flash Interface (CFI) flash, quad Serial Peripheral Interface (SPI) flash, or NAND flash memory devices with the device JTAG interface. • Control Altera FPGA configuration from a CFI flash, quad SPI flash, or NAND flash memory device for Arria series, Cyclone series, and Stratix series FPGA devices. Installing and Licensing IP Cores The Altera IP Library provides many useful IP core functions for your production use without purchasing an additional license. Some Altera MegaCore® IP functions require that you purchase a separate license for production use. However, the OpenCore® feature allows evaluation of any Altera® IP core in simulation and compilation in the Quartus® II software. After you are satisfied with functionality and perfformance, visit the Self Service Licensing Center to obtain a license number for any Altera product. Figure 1: IP Core Installation Path acds quartus - Contains the Quartus II software ip - Contains the Altera IP Library and third-party IP cores altera - Contains the Altera IP Library source code <IP core name> - Contains the IP core source files Note: The default IP installation directory on Windows is <drive>:\altera\<version number>; on Linux it is <home directory>/altera/ <version number>. © 2015 Altera Corporation. All rights reserved. ALTERA, ARRIA, CYCLONE, ENPIRION, MAX, MEGACORE, NIOS, QUARTUS and STRATIX words and logos are trademarks of Altera Corporation and registered in the U.S. Patent and Trademark Office and in other countries. All other words and logos identified as trademarks or service marks are the property of their respective holders as described at www.altera.com/common/legal.html. Altera warrants performance of its semiconductor products to current specifications in accordance with Altera's standard warranty, but reserves the right to make changes to any products and services at any time without notice. Altera assumes no responsibility or liability arising out of the application or use of any information, product, or service described herein except as expressly agreed to in writing by Altera. Altera customers are advised to obtain the latest version of device specifications before relying on any published information and before placing orders for products or services. www.altera.com 101 Innovation Drive, San Jose, CA 95134 ISO 9001:2008 Registered 2 UG-01082 2015.06.15 Device Support Related Information • Altera Licensing Site • Altera Software Installation and Licensing Manual Device Support This user guide focuses on implementing the PFL IP core in an Altera CPLD. The PFL IP core supports all Altera FPGAs. You can implement the PFL IP core in an Arria®, Cyclone®, or Stratix® device family FPGA to program flash memory or to configure other FPGAs. Related Information AN478: Using FPGA-Based Parallel Flash Loader with the Quartus II Software Provides more information about using the FPGA-based PFL IP core to program a flash memory device. Supported Flash Memory Devices The Quartus II software generates the PFL IP core logic for the flash programming bridge and FPGA configuration. Table 1: CFI Flash Memory Devices Supported by PFL IP Core If your CFI device is not in the following table, but is compatible with an Intel or Spansion CFI flash device, Altera recommends selecting Define CFI Flash Device in the Quartus II software. Manufacturer Product Family C3 Data Width 16 Micron J3 8 or 16 16 (1) (2) Density (Megabit) Device Name(1)(2) 8 28F800C3 16 28F160C3 32 28F320C3 64 28F640C3 32 28F320J3 64 28F640J3 128 28F128J3 256 JS29F256J3 Spansion has discontinued the Spansion S29GL-N flash memory device family. Altera does not recommend using this flash memory device. For more information about an alternative recommendation, see related information. The PFL IP core supports top and bottom boot block of the flash memory devices. For Micron flash memory devices, the PFL IP core supports top, bottom, and symmetrical blocks of flash memory devices. Altera Corporation Parallel Flash Loader IP Core User Guide Send Feedback UG-01082 2015.06.15 Supported Flash Memory Devices Manufacturer Product Family P30 P33 M29EW Data Width 16 16 8 or 16 Density (Megabit) 3 Device Name(1)(2) 64 28F640P30 128 28F128P30 256 28F256P30 512 28F512P30 1000 28F00AP30 2000 28F00BP30 128 28F128P33 256 28F256P33 512 28F512P33 640 28F640P33 1000 28F00AP33 2000 28F00BP33 256 28F256M29EW 512 28F512M29EW 1000 28F00AM29EW M28W160CT M28W160CB 16 M29W160F7 M29W160FB M29W320E M29W 8 or 16 32 M29W320FT M29W320FB M29W640F 64 M29DW (1) (2) 8 or 16 32 M29W640G 128 M29W128G 256 M29W256G M29DW323DT M29DW323DB Spansion has discontinued the Spansion S29GL-N flash memory device family. Altera does not recommend using this flash memory device. For more information about an alternative recommendation, see related information. The PFL IP core supports top and bottom boot block of the flash memory devices. For Micron flash memory devices, the PFL IP core supports top, bottom, and symmetrical blocks of flash memory devices. Parallel Flash Loader IP Core User Guide Send Feedback Altera Corporation 4 UG-01082 2015.06.15 Supported Flash Memory Devices Manufacturer Product Family G18 M58BW Data Width 16 32 16 or 32 GL-P(3) AL-D Spansion 8 or 16 8 or 16 MT28GU512AAA1E GC-0SIT 1024 MT28GU01GAAA1E GC-0SIT 16 M58BW16FT M58BW16FB 32 M58BW32FT 32 M58BW32FB 128 S29GL128P 256 S29GL256P 512 S29GL512P 1024 S29GL01GP 16 S29AL016D 32 S29AL032D 16 S29AL016J AL-M 8 or 16 16 S29AL016M 32 S29JL032H 64 S29JL064H 128 S29WS128N 128 S29GL128S 256 S29GL256S 512 S29GL512S 1024 S29GL01GS 16 MX29LV160D 32 MX29LV320D GL-S MX29LV 8 or 16 16 16 16 Macronix 64 MX29GL (3) 512 8 or 16 WS-N (2) Device Name(1)(2) AL-J JL-H (1) Density (Megabit) 16 MX29LV640D MX29LV640E 128 MX29GL128E 256 MX29GL256E Spansion has discontinued the Spansion S29GL-N flash memory device family. Altera does not recommend using this flash memory device. For more information about an alternative recommendation, see related information. The PFL IP core supports top and bottom boot block of the flash memory devices. For Micron flash memory devices, the PFL IP core supports top, bottom, and symmetrical blocks of flash memory devices. Supports page mode. Altera Corporation Parallel Flash Loader IP Core User Guide Send Feedback UG-01082 2015.06.15 Supported Flash Memory Devices Manufacturer Eon Silicon Solution Product Family Data Width EN29LV 16 EN29GL 16 Density (Megabit) 5 Device Name(1)(2) 16 EN29LV160B 32 EN29LV320B 128 EN29GL128 Table 2: Quad SPI Flash Memory Device Supported by PFL IP Core Manufacturer Micron Product Family N25Q 1.8V N25Q 3.3V FL Spansion FS (1) (2) Density (Megabit) Device Name 128 N25Q128 32 S25FL032P 64 S25FL064P 128 S25FL129P 256 S25FS256S 512 S25FS512S Spansion has discontinued the Spansion S29GL-N flash memory device family. Altera does not recommend using this flash memory device. For more information about an alternative recommendation, see related information. The PFL IP core supports top and bottom boot block of the flash memory devices. For Micron flash memory devices, the PFL IP core supports top, bottom, and symmetrical blocks of flash memory devices. Parallel Flash Loader IP Core User Guide Send Feedback Altera Corporation 6 UG-01082 2015.06.15 Supported Flash Memory Devices Manufacturer Product Family Density (Megabit) 8 Device Name MX25L8035E MX25L8036E MX25L1635D 16 MX25L1635E MX25L1636D MX25L1636E MX25L3225D MX25L3235D 32 MX25L MX25L3235D MX25L3236D MX25L3237D MX25L6436E Macronix 64 MX25L6445E MX25L6465E MX25L12836E 128 MX25L12845E MX25L12865E 256 8 MX25U MX25L25635E MX25L25735E MX25U8035 MX25U8035E 16 MX25U1635E 32 MX25U3235E 64 MX25U6435E Table 3: NAND Flash Memory Device Supported by PFL IP Core Manufacturer Density (Megabit) Device Name NAND512 1.8V Micron 512 NAND512 3.0V NAND512 3.3V Micron(MT29) Samsung 512 K9F1208R0C Toshiba 1000 TC58DVG02A1 Hynix 512 HY27US0812(1/2)B Altera Corporation Parallel Flash Loader IP Core User Guide Send Feedback UG-01082 2015.06.15 Supported Schemes and Features 7 Related Information Spansion Website Supported Schemes and Features The PFL IP core allows you to configure the FPGA in passive serial (PS) or fast passive parallel (FPP) scheme. The PFL IP core supports configuration with FPGA on-chip data compression and data encryption. When you use compressed or encrypted configuration data for FPP configuration, the PFL IP core holds one data byte for one, two, four, or eight DCLK cycles to ensure the DCLK frequency runs at the required data rate as specified by the DCLK-to-DATA[] Ratio. The PFL IP core checks if the compression or encryption feature is turned on in the configuration image before configuring in FPP mode. Hence, no additional setting is required in the PFL IP core to specify whether the configuration file stored in the flash memory device is a compressed or uncompressed image. Note: When you turn on the enhanced bitstream compression feature, data encryption is disabled. You can program the Altera CPLDs and flash memory device in Programmer Object File (.pof), Jam™ Standard Test and Programming Language (STAPL) Format File (.jam), or JAM Byte Code File (.jbc) file format. The PFL IP core does not support Raw Binary File (.rbf) format. Logic element (LE) usage varies with different PFL IP core and Quartus II software settings. To determine the exact LE usage number, compile a PFL design with your settings using the Quartus II software. IP Catalog and Parameter Editor The Quartus II IP Catalog (Tools > IP Catalog) and parameter editor help you easily customize and integrate IP cores into your project. You can use the IP Catalog and parameter editor to select, customize, and generate files representing your custom IP variation. Note: The IP Catalog (Tools > IP Catalog) and parameter editor replace the MegaWizard Plug-In Manager for IP selection and parameterization, beginning in Quartus II software version 14.0. Use the IP Catalog and parameter editor to locate and paramaterize Altera IP cores. ™ The IP Catalog lists installed IP cores available for your design. Double-click any IP core to launch the parameter editor and generate files representing your IP variation. The parameter editor prompts you to specify an IP variation name, optional ports, and output file generation options. The parameter editor generates a top-level Qsys system file (.qsys) or Quartus II IP file (.qip) representing the IP core in your project. You can also parameterize an IP variation without an open project. Use the following features to help you quickly locate and select an IP core: • Filter IP Catalog to Show IP for active device family or Show IP for all device families. If you have no project open, select the Device Family in IP Catalog. • Type in the Search field to locate any full or partial IP core name in IP Catalog. • Right-click an IP core name in IP Catalog to display details about supported devices, open the IP core's installation folder, and view links to documentation. • Click Search for Partner IP, to access partner IP information on the Altera website. Parallel Flash Loader IP Core User Guide Send Feedback Altera Corporation 8 UG-01082 2015.06.15 Using the Parameter Editor Figure 2: Quartus II IP Catalog Show IP only for target device Search for installed IP cores Double-click to customize, right-click for detailed information Note: The IP Catalog is also available in Qsys (View > IP Catalog). The Qsys IP Catalog includes exclusive system interconnect, video and image processing, and other system-level IP that are not available in the Quartus II IP Catalog. For more information about using the Qsys IP Catalog, refer to Creating a System with Qsys in the Quartus II Handbook. Using the Parameter Editor The parameter editor helps you to configure IP core ports, parameters, and output file generation options. • Use preset settings in the parameter editor (where provided) to instantly apply preset parameter values for specific applications. • View port and parameter descriptions, and links to documentation. • Generate testbench systems or example designs (where provided). Altera Corporation Parallel Flash Loader IP Core User Guide Send Feedback UG-01082 2015.06.15 Functional Description 9 Figure 3: IP Parameter Editors View IP port and parameter details Legacy parameter editors Specify your IP variation name and target device Apply preset parameters for specific applications Functional Description The PFL IP core allows you to program flash memory devices with Altera CPLDs through the JTAG interface and provides the logic to control configuration from the flash memory device to the Altera FPGA. Programming Flash Memory You can use the PFL IP core to program the following flash memory devices with JTAG interface: • Programming CFI Flash • Programming Quad SPI Flash • Programming NAND Flash Related Information • Supported Flash Memory Devices on page 2 • Third-party Programmer Support on page 39 Provides more information about programming the flash memory using third-party tools. Programming CFI Flash Altera configuration devices support programming through the JTAG interface to allow in-system programming and updates. However, standard flash memory devices do not support the JTAG interface. You can use the JTAG interface in Altera CPLDs to indirectly program the flash memory device. The Altera CPLD JTAG block interfaces directly with the logic array in a special JTAG mode. This mode brings the JTAG chain through the logic array instead of the Altera CPLD boundary-scan cells (BSCs). Parallel Flash Loader IP Core User Guide Send Feedback Altera Corporation 10 UG-01082 2015.06.15 Programming Quad SPI Flash The PFL IP core provides JTAG interface logic to convert the JTAG stream provided by the Quartus II software and to program the CFI flash memory devices connected to the CPLD I/O pins. Figure 4: Programming the CFI Flash Memory With the JTAG Interface Figure shows an Altera CPLD configured as a bridge to program the CFI flash memory device through the JTAG interface. Altera CPLD Quartus II Software via JTAG Configuration Data Altera FPGA PFL Common Flash Interface Altera FPGA Not Used for Flash Programming CFI Flash Memory The PFL IP core supports dual P30 or P33 CFI flash memory devices in burst read mode to achieve faster configuration time. Two identical P30 or P33 CFI flash memory devices connect to the CPLD in parallel using the same data bus, clock, and control signals. During FPGA configuration, the FPGA DCLK frequency is four times faster than the flash_clk frequency. Figure 5: PFL IP core With Dual P30 or P33 CFI Flash Memory Devices The flash memory devices in the dual P30 or P33 CFI flash solution must have the same memory density from the same device family and manufacturer. In the Quartus II software version 9.1 SP1 onwards, dual P30 or P33 flash support is available in the PFL IP core. ADDR[24..0] NCE NWE NOE DATA[15..0] 16 P30/P33 CFI Flash ADDR[24..0] NCE NWE NOE DATA[15..0] VCC Altera CPLD P30/P33 CFI Flash flash_addr[24..0] flash_nce flash_nwe flash_noe flash_data[31..0] 10kΩ fpga_conf_done fpga_nstatus fpga_nconfig fpga_data fpga_dclk VCC 10kΩ VCC 10kΩ Altera FPGA CONF_DONE nSTATUS nCONFIG DATA DCLK nCE 16 Programming Quad SPI Flash You can also use the JTAG interface in Altera CPLDs to program a quad SPI flash memory device with the PFL IP core. Altera Corporation Parallel Flash Loader IP Core User Guide Send Feedback UG-01082 2015.06.15 Programming Quad SPI Flash 11 The PFL IP core instantiated in the Altera CPLD functions as a bridge between the CPLD JTAG program‐ ming interface and the quad SPI flash memory device interface that connects to the Altera CPLD I/O pins. You can connect up to four identical quad SPI flashes in parallel to implement more configuration data storage. Note: When connecting quad SPI flashes in parallel, use identical flash memory devices with the same memory density from the same device family and manufacturer. In the Quartus II software version 10.0 onwards, quad SPI flash support is available in the PFL IP core. Figure 6: Programming Quad SPI Flash Memory Devices With the CPLD JTAG Interface Figure shows an Altera CPLD functioning as a bridge to program the quad SPI flash memory device through the JTAG interface. The PFL IP core supports multiple quad SPI flash programming of up to four devices. Quad SPI Flash flash_sck flash_ncs flash_io0 flash_io1 flash_io2 flash_io3 Quad SPI Flash Altera CPLD flash_sck[3..0] flash_ncs[3..0] flash_io0[3..0] flash_io1[3..0] flash_io2[3..0] flash_io3[3..0] VCC 10kΩ VCC 10kΩ VCC 10kΩ Altera FPGA fpga_conf_done fpga_nstatus fpga_nconfig fpga_data fpga_dclk flash_sck flash_ncs flash_io0 flash_io1 flash_io2 flash_io3 CONF_DONE nSTATUS nCONFIG DATA DCLK nCE Quad SPI Flash flash_sck flash_ncs flash_io0 flash_io1 flash_io2 flash_io3 Quad SPI Flash flash_sck flash_ncs flash_io0 flash_io1 flash_io2 flash_io3 Related Information Supported Flash Memory Devices on page 2 Parallel Flash Loader IP Core User Guide Send Feedback Altera Corporation 12 UG-01082 2015.06.15 Programming NAND Flash Programming NAND Flash You can use the JTAG interface in Altera CPLDs to program the NAND flash memory device with the PFL IP core. The NAND flash memory device is a simpler device that has faster erase and write speed with higher memory density in comparison with the CFI flash. You can use the JTAG interface in Altera CPLDs to indirectly program the flash memory device. The CPLD JTAG block interfaces directly with the logic array in a special JTAG mode. This mode brings the JTAG chain through the logic array instead of the Altera CPLD BSCs. The PFL IP core provides JTAG interface logic to convert the JTAG stream from the Quartus II software and to program the NAND flash memory device that connects to the CPLD I/O pins. Figure 7: Programming NAND Flash Memory Devices With the JTAG Interface Figure shows an Altera CPLD functioning as a bridge to program the NAND flash memory device through the JTAG interface. Altera CPLD Quartus II Software using JTAG Configuration Data Altera FPGA PFL Open NAND Flash Interface Altera FPGA Not Used for Flash Programming NAND Flash Memory Controlling Altera FPGA Configuration from Flash Memory You can use the PFL logic in Altera CPLDs as a configuration controller for FPGA configuration. The PFL logic in the CPLD determines when to start the configuration process, read the data from the flash memory device, and configure the Altera FPGA in PS or FPP configuration scheme. Figure 8: FPGA Configuration With Flash Memory Data Figure shows the Altera CPLD as the configuration controller for the FPGA. The flash memory includes CFI, quad SPI and NAND flash. Altera CPLD PFL Passive Serial or Fast Passive Parallel Interface Altera FPGA Flash Interface Flash Memory Altera Corporation Parallel Flash Loader IP Core User Guide Send Feedback UG-01082 2015.06.15 Mapping PFL and Flash Address 13 You can use the PFL IP core to either program the flash memory devices, configure your FPGA, or both; however, to perform both functions, create separate PFL functions if any of the following conditions apply to your design: • • • • You want to use fewer LEs. You modify the flash data infrequently. You have JTAG or In-System Programming (ISP) access to the Altera CPLD. You want to program the flash memory device with non-Altera data. For example, the flash memory device contains initialization storage for an ASSP. You can use the PFL IP core to program the flash memory device with the initialization data and also create your own design source code to implement the read and initialization control with the CPLD logic. Creating Separate PFL Functions To create separate PFL functions, follow these steps: 1. 2. 3. 4. 5. 6. To create a PFL instantiation, select Flash Programming Only mode. Assign the pins appropriately. Compile and generate a .pof for the flash memory device. Ensure that you tri-state all unused I/O pins. To create another PFL instantiation, select Configuration Control Only mode. Instantiate this configuration controller into your production design. Whenever you must program the flash memory device, program the CPLD with the flash memory device .pof and update the flash memory device contents. 7. Reprogram the CPLD with the production design .pof that includes the configuration controller. Note: All unused pins are set to ground by default. When programming the configuration flash memory device through the CPLD JTAG pins, you must tri-state the FPGA configuration pins common to the CPLD and the configuration flash memory device. You can use the pfl_flash_access_request and pfl_flash_access_granted signals of the PFL block to tri-state the correct FPGA configuration pins. Related Information • • • • Mapping PFL and Flash Address on page 13 Implementing Page in the Flash .pof on page 15 Using Enhanced Bitstream Compression and Decompression on page 18 Using Remote System Upgrade on page 20 Mapping PFL and Flash Address The address connections between the PFL IP core and the flash memory device vary depending on the flash memory device vendor and data bus width. Parallel Flash Loader IP Core User Guide Send Feedback Altera Corporation 14 UG-01082 2015.06.15 Mapping PFL and Flash Address Figure 9: Micron J3 Flash Memory in 8-Bit Mode The address connection between the PFL IP core and the flash memory device are the same. PFL address: 24 bits 23 22 21 2 1 0 Flash Memory address: 24 bits 23 22 21 2 1 0 Figure 10: Micron J3, P30, and P33 Flash Memories in 16-Bit Mode The flash memory addresses in Micron J3, P30, and P33 16-bit flash memory shift one bit down in comparison with the flash addresses in the PFL IP core. The flash address in the Micron J3, P30, and P33 flash memory starts from bit 1 instead of bit 0. PFL address: 23 bits 22 21 20 2 1 0 Flash Memory address: 23 bits 23 22 21 3 2 1 Figure 11: Spansion and Micron M28, M29 Flash Memory in 8-Bit Mode The flash memory addresses in Spansion 8-bit flash shifts one bit up. Address bit 0 of the PFL IP core connects to data pin D15 of the flash memory. PFL address: 24 bits 23 22 21 2 1 0 Altera Corporation Flash Memory address: 24 bits 22 21 20 1 0 D15 Parallel Flash Loader IP Core User Guide Send Feedback UG-01082 2015.06.15 Implementing Page in the Flash .pof 15 Figure 12: Spansion and Micron M28, M29 Flash Memory in 16-Bit Mode The address bit numbers in the PFL IP core and the flash memory device are the same. PFL address: 23 bits 22 21 20 2 1 0 Flash Memory address: 23 bits 22 21 20 2 1 0 Implementing Page in the Flash .pof The PFL IP core stores configuration data in a maximum of eight pages in a flash memory block. Each page holds the configuration data for a single FPGA chain. A single FPGA chain can contain more than one FPGA. For an FPGA chain with multiple FPGAs, the PFL IP core stores multiple SRAM Object Files (.sof) in the same page. The total number of pages and the size of each page depends on the density of the flash. These pages allow you to store designs for different FPGA chains or different designs for the same FPGA chain in different pages. Use the generated .sof files to create a flash memory device .pof. When converting these .sof files to a .pof, use the following address modes to determine the page address: • Block mode—Allows you to specify the start and end addresses for the page. • Start mode—Allows you to specify only the start address. You can locate the start address for each page on an 8-KB boundary. If the first valid start address is 0×000000, the next valid start address is an increment of 0×2000. • Auto mode—Allows the Quartus II software to automatically determine the start address of the page. The Quartus II software aligns the pages on a 128-KB boundary; for example, if the first valid start address is 0×000000, the next valid start address is an increment of 0×20000. Note: If you are programming NAND flash, you must specify the NAND flash memory device reserved block start address and the start address to ensure the files reside within a 128-KB boundary Storing Option Bits The PFL IP core requires you to allocate space in the flash memory device for option bits. The option bits sector contains information about the start address for each page, the .pof version used for flash programming, and the Page-Valid bits. You must specify the options bits sector address in the flash memory device when converting the .sof files to a .pof and creating a PFL design. Parallel Flash Loader IP Core User Guide Send Feedback Altera Corporation 16 UG-01082 2015.06.15 Storing Option Bits Table 4: Option Bits Sector Format Offset address 0x80 stores the .pof version required for programming flash memory. This .pof version applies to all eight pages of the configuration data. The PFL IP core requires the .pof version to perform a successful FPGA configuration process. Sector Offset Value 0x00–0x03 Page 0 start address 0x04–0x07 Page 1 start address 0x08–0x0B Page 2 start address 0x0C–0x0F Page 3 start address 0x10–0x13 Page 4 start address 0x14–0x17 Page 5 start address 0x18–0x1B Page 6 start address 0x1C–0x1F Page 7 start address 0x20–0x7F Reserved 0x80(4) .pof version 0x81–0xFF Reserved The Quartus II Convert Programming File tool generates the information for the .pof version when you convert the .sof files to .pof files. The value for the .pof version generated by the Quartus II software version 7.1 onwards is 0x03. However, if you turn on the enhanced bitstream-compression feature, the value for the .pof version is 0x04. Caution: Do not overwrite any information in the option bits sector to prevent the PFL IP core from malfunctioning, and always store the option bits in unused addresses in the flash memory device. (4) .pof version occupies only one byte in the option bits sector. Altera Corporation Parallel Flash Loader IP Core User Guide Send Feedback UG-01082 2015.06.15 Storing Option Bits 17 Figure 13: Implementing Page Mode and Option Bits in the CFI Flash Memory Device • The end address depends on the density of the flash memory device. For the address range for devices with different densities, refer Byte Address Range table. • You must specify the byte address for the option bits sector. End Address 8 Bits Option Bits Configuration Data (Page 2) 32 Bits Page 2 Address + Page-Valid Page 1 Address + Page-Valid Page 0 Address + Page-Valid Configuration Data (Page 1) Configuration Data (Page 0) 0x000000 Figure 14: Page Start Address, End Address, and Page-Valid Bit Stored as Option Bits Bits 0 to 12 for the page start address are set to zero and are not stored as option bits. The Page-Valid bits indicate whether each page is successfully programmed. The PFL IP core programs the Page-Valid bits after successfully programming the pages. 0x002000 (For flash byte addressing mode) Bit 7...Bit 1 Bit 0 Page Start Address [19:13] Page-Valid Bit 7...Bit 0 0x002001 Page Start Address [27:20] Bit 7...Bit 1 0x002002 Page End Address [19:13] Bit 7...Bit 0 0x002003 Page End Address [27:20] Table 5: Byte Address Range for CFI Flash Memory Devices with Different Densities CFI Device (Megabit) Address Range 8 0x0000000–0x00FFFFF Parallel Flash Loader IP Core User Guide Send Feedback Altera Corporation 18 UG-01082 2015.06.15 Using Enhanced Bitstream Compression and Decompression CFI Device (Megabit) Address Range 16 0x0000000–0x01FFFFF 32 0x0000000–0x03FFFFF 64 0x0000000–0x07FFFFF 128 0x0000000–0x0FFFFFF 256 0x0000000–0x1FFFFFF 512 0x0000000–0x3FFFFFF 1024 0x0000000–0x7FFFFFF Using Enhanced Bitstream Compression and Decompression The enhanced bitstream compression and decompression feature in the PFL IP core reduces the size of the configuration file in the flash memory device. On average, you can reduce the file size by as much as 50% depending on the designs. When you turn on the enhanced bitstream compression feature, the PFL IP core disables data encryption. Table 6: Comparison Between Typical, Enhanced, and Double Compression FPGA Configuration Typical Bitstream Compression Feature Enhanced Bitstream Compression Feature Double Compression Technique FPGA on-chip bitstream decompression enabled Yes No Yes PFL enhanced bitstream decompression enabled No Yes Yes 35%–55% 45%–75% 40%–60% Moderate(5) Slow Moderate(5) Fast(6) Very fast(7) Not supported Typical configuration file size reduction PS configuration time FPP configuration time Note: When using the PFL with compression, set the device MSEL pins set for compression or decompression. When generating or converting a programming file, you can enable compression. In the first few bytes during the generation of the programming file (with compression enabled), a bit set notifies the PFL that the incoming files is a compressed file. The ×4 DCLK-to-data are handled automatically in the PFL. Note: For more information about the typical data compression feature, refer to the Configuration Data Decompression section in the configuration chapter of the relevant device handbook. (5) (6) (7) The FPGA receives compressed bitstream which decreases the duration to transmit the bitstream to the FPGA. For FPP with on-chip bitstream decompression enabled, the DCLK frequency is ×2, ×4, or ×8 the data rate, depending on the device. You can check the relationship of the DCLK and data rate in the FPP Configuration section in the configuration chapter of the respective device handbook. For FPP with enhanced bitstream decompression enabled, the DCLK frequency is ×1 the data rate. Altera Corporation Parallel Flash Loader IP Core User Guide Send Feedback UG-01082 2015.06.15 Using Enhanced Bitstream Compression and Decompression 19 For the FPP configuration scheme, the enhanced bitstream compression feature helps achieve higher configuration data compression ratio and faster configuration time. For the PS configuration scheme, the double compression technique helps achieve higher configuration data compression ratio and moderate configuration time. To enable the double compression technique, turn on both the typical bitstream compression feature and the enhanced bitstream compression feature in the PFL parameter editor. Figure 15: FPGA Configuration Data Flow with Enhanced Bitstream Compression Feature in PS or FPP Configuration Scheme Passive Serial or Fast Passive Parallel With Uncompressed Data Altera CPLD PFL with Enhanced Bitstream Decompression Feature Altera FPGA Compressed Data CFI or Quad SPI Flash Memory Figure 16: FPGA Configuration Data Flow with Double Compression Technique in PS Configuration Scheme Altera CPLD PFL with Enhanced Bitstream Decompression Feature Passive Serial With Compressed Data Altera FPGA On-Chip Bitstream Decompression Feature Double Compressed Data CFI or Quad SPI Flash Memory Note: The enhanced bitstream compression and decompression feature is available in the PFL IP core in the Quartus II software version 10.0 onwards. Parallel Flash Loader IP Core User Guide Send Feedback Altera Corporation 20 UG-01082 2015.06.15 Using Remote System Upgrade Using Remote System Upgrade When you instantiate the PFL IP core in the Altera CPLD for FPP or PS configuration, you can use the features in the PFL IP core to perform remote system upgrade. You can download a new configuration image from a remote location, store it in the flash memory device, and direct the PFL IP core to trigger an FPGA reconfiguration to load the new configuration image. You must store each configuration image as a new page in the flash memory device. The PFL IP core supports a maximum of eight pages. When using remote system upgrade, the configuration images are classified as a factory image or as application images. A factory image is a user-defined fall-back or safe configuration that performs system recovery when unintended errors occur during or after application image configuration. The factory image is written to the flash memory device only once by the system manufacturer and you must not modify or overwrite the factory image. Application images implement user-defined functionality in the target FPGA and you can remotely update in the system. Figure 17: Remote System Upgrade Implementation with the PFL IP Core in FPP and PS Configuration Scheme Altera CPLD Quartus II Software via JTAG Configuration Data PFL Common Flash Interface Altera FPGA Altera FPGA Not Used for Flash Programming CFI Flash Memory Remote System Upgrade State Machine in the PFL IP Core After FPGA powers up, you have the flexibility to determine whether a factory image or any application image is to be loaded by setting the fpga_pgm[2..0] input pin to the page in which the intended configuration image is stored. If an error occurs while loading the configuration image, the PFL IP core triggers a reconfiguration to automatically load the factory image. After the FPGA successfully loads the configuration image, the FPGA enters user mode. After the FPGA enters user mode, you can initiate a reconfiguration to a new page by following these steps: 1. 2. 3. 4. Altera Corporation Set the fpga_pgm[2.0] input pin. Release the pfl_nreset to high if the pfl_nreset is asserted to low. After four or five clock cycles, pulse the pfl_nreconfigure input pin to low. Ensure that all transition is synchronized to pfl_clk. Parallel Flash Loader IP Core User Guide Send Feedback UG-01082 2015.06.15 Remote System Upgrade State Machine in the PFL IP Core 21 Figure 18: Transitions Between Different Configurations in Remote System Upgrade • The remote system upgrade feature in the PFL IP core does not restrict the factory image to page 0, but allows the factory image to be located on other pages in the flash. • You can load the FPGA with either a factory image or any application image after power up, depending on the fpga_pgm[2..0] setting. Configuration Error Factory Configuration fpga_pgm[2..0] is set to factory page Set fpga_pgm[2..0] to intended page and pulse pfl_nreconfig Power-up fpga_pgm[2..0] is set to application 1 page Configuration Error Application 1 Configuration Set fpga_pgm[2..0] to intended page and pulse pfl_nreconfig Set fpga_pgm[2..0] to intended page and pulse pfl_nreconfig fpga_pgm[2..0] is set to application n page Application n Configuration Configuration Error Note: The PFL IP core can implement a Last Revision First programming order. The application image is updated with remote system upgrade capabilities. If a flash programming error causes the FPGA configuration to fail, the FPGA is reconfigured from the factory image address. A system shipped from the factory has the same configuration file at the application image address and the factory Parallel Flash Loader IP Core User Guide Send Feedback Altera Corporation 22 UG-01082 2015.06.15 Implementing Remote System Upgrade with the PFL IP Core image address. Altera recommends that you write-protect the factory image blocks in the flash memory device. Implementing Remote System Upgrade with the PFL IP Core You can achieve the remote system upgrade capabilities with the PFL IP core by controlling the fpga_pgm[2..0] and the pfl_nreconfigure ports. To control the fpga_pgm[2..0] and the pfl_nreconfigure ports, user-defined logic must perform the following capabilities: • After FPGA power up, user logic sets the fpga_pgm[2..0] ports to specify which page of configuration image is to be loaded from the flash. • After the remote host completes the new image update to the flash, user logic triggers a reconfigura‐ tion by pulling the pfl_nreconfigure pin low and setting the fpga_pgm[2..0] to the page in which the new image is located. The pfl_nreconfigure signal pulsed low for greater than one pfl_clk cycle. • If you have enabled the user watchdog timer, user logic can monitor the pfl_watchdog_error port to detect any occurrence of watchdog time-out error. If the pfl_watchdog_error pin is asserted high, this indicates watchdog time-out error. You can use the user logic to set the fpga_pgm[2..0] and pull the pfl_nreconfigure port low to initiate FPGA reconfiguration. The recovery page to be loaded from the flash memory device after watchdog timer error depends on the fpga_pgm[2..0] setting. Figure 19: Implementation of Remote System Upgrade with the PFL IP Core Altera CPLD Altera FPGA Watchdog timer reset circuitry Watchdog timer reset Image update circuitry Flash FPP or PS configuration PFL pfl_nreconfigure fpga_pgm[2..0] User logic Remote Host User Watchdog Timer The user watchdog timer prevents faulty configuration from stalling the device indefinitely. The system uses the timer to detect functional errors after a configuration image is successfully loaded into the FPGA. The user watchdog timer is a time counter that runs at the pfl_clk frequency. The timer begins counting after the FPGA enters user mode and continues until the timer reaches the watchdog time out Altera Corporation Parallel Flash Loader IP Core User Guide Send Feedback UG-01082 2015.06.15 Using the PFL IP Core 23 period. You must periodically reset this timer by asserting the pfl_reset_watchdog pin before the watchdog time-out period. If the timer does not reset before the watchdog time-out period, the PFL IP core detects watchdog time-out error and initiates a reconfiguration to load the factory image. Instantiate the watchdog timer reset circuitry in the configuration image loaded into the FPGA. Connect one output signal from the reset circuitry to the pfl_reset_watchdog pin of the PFL in the CPLD to periodically send a reset signal to the user watchdog timer. To reset the watchdog timer correctly, hold the pfl_reset_watchdog pin high or low for at least two pfl_clk cycles. Note: The user watchdog timer feature for remote system upgrade is available in the PFL IP core in the Quartus II software version 10.0 onwards. Using the PFL IP Core This section describes the procedures on how to use the PFL IP core. Figure 20: Process for Using the PFL IP Core Figure shows the process for using the PFL IP core, using MAX II as an example. Create new FPGA designs Create a new MAX II design, instantiate the PFL Megafunction in the MAX II design, and create Pin Assignments Compile and obtain the FPGA .sof(s) Compile and obtain MAX II .pof Add the .sof(s) for conversion to .pof Convert to .pof for the Targeted Flash Add the MAX II .pof to the Quartus II Programmer Add the flash .pof in the Quartus II Programmer Create the optional Jam programming file Program the MAX II and Flash Devices MAX II configures the FPGA with the configuration data from the Flash Device Parallel Flash Loader IP Core User Guide Send Feedback Altera Corporation 24 UG-01082 2015.06.15 Customizing and Generating IP Cores Related Information AN478: Using FPGA-Based Parallel Flash Loader with the Quartus II Software Provides more information about using the FPGA-based PFL IP core to program a flash memory device. Customizing and Generating IP Cores You can customize IP cores to support a wide variety of applications. The Quartus II IP Catalog displays IP cores available for the current target device. The parameter editor guides you to set parameter values for optional ports, features, and output files. To customize and generate a custom IP core variation, follow these steps: 1. In the IP Catalog (Tools > IP Catalog), locate and double-click the name of the IP core to customize. The parameter editor appears. 2. Specify a top-level name for your custom IP variation. This name identifies the IP core variation files in your project. If prompted, also specify the target Altera device family and output file HDL preference. Click OK. 3. Specify the desired parameters, output, and options for your IP core variation: • Optionally select preset parameter values. Presets specify all initial parameter values for specific applications (where provided). • Specify parameters defining the IP core functionality, port configuration, and device-specific features. • Specify options for generation of a timing netlist, simulation model, testbench, or example design (where applicable). • Specify options for processing the IP core files in other EDA tools. 4. Click Finish or Generate to generate synthesis and other optional files matching your IP variation specifications. The parameter editor generates the top-level .qip or .qsys IP variation file and HDL files for synthesis and simulation. Some IP cores also simultaneously generate a testbench or example design for hardware testing. 5. To generate a simulation testbench, click Generate > Generate Testbench System. Generate > Generate Testbench System is not available for some IP cores. 6. To generate a top-level HDL design example for hardware verification, click Generate > HDL Example. Generate > HDL Example is not available for some IP cores. When you generate the IP variation with a Quartus II project open, the parameter editor automatically adds the IP variation to the project. Alternatively, click Project > Add/Remove Files in Project to manually add a top-level .qip or .qsys IP variation file to a Quartus II project. To fully integrate the IP into the design, make appropriate pin assignments to connect ports. You can define a virtual pin to avoid making specific pin assignments to top-level signals. Note: By default, all unused pins are tied to ground. Altera recommends setting all unused pins to tristate because doing otherwise might cause interference. To set all unused pins to tri-state, in the Quartus II software, click Assignments > Device > Device and Pin Options > Unused Pins and select an item from the Reserve all unused pins list. Converting .sof Files to a .pof To generate a programming file with different compression features, you must convert the .sof files to a .pof. Altera Corporation Parallel Flash Loader IP Core User Guide Send Feedback UG-01082 2015.06.15 Converting .sof Files to a .pof 25 To convert the .sof files to a .pof, follow these steps: 1. On the File menu, click Convert Programming Files. 2. For Programming file type, specify Programmer Object File (.pof) and name the file. 3. For Configuration device, select the CFI or NAND flash memory device with the correct density. For example, CFI_32Mb is a CFI device with 32-Megabit (Mb) capacity. 4. To add the configuration data, under Input files to convert, select SOF Data. 5. Click Add File and browse to the .sof files you want to add. You can place more than one .sof in the same page if you intend to configure a chain of FPGAs. The order of the .sof files must follow the order of the devices in the chain. If you want to store the data from other .sof files in a different page, click Add SOF page. Add the .sof files to the new page. 6. Select SOF Data and click Properties to set the page number and name. Under Address mode for selected pages, select Auto to let the Quartus II software automatically set the start address for that page. Select Block to specify the start and end addresses, or select Start to specify the start address only. 7. Click OK. 8. You can also store Hexadecimal (Intel-Format) File (.hex) user data in the flash memory device: a. In the Input files to convert sub-window of the Convert Programming Files window, select Add Hex Data. b. In the Add Hex Data dialog box, select either absolute or relative addressing mode. • If you select absolute addressing mode, the data in the .hex is programmed in the flash memory device at the exact same address location listed in the .hex. • If you select relative addressing mode, specify a start address. The data in the .hex is programmed into the flash memory device with the specific start address, and the differences between the addresses are kept. If no address is specified, the Quartus II software selects an address. Note: You can also add other non-configuration data to the .pof by selecting the .hex that contains your data when creating the flash memory device .pof. 9. Click Options to specify the start address to store the option bits. This start address must be identical to the address you specify when creating the PFL IP core. Ensure that the option bits sector does not overlap with the configuration data pages and that the start address resides on an 8-KB boundary. 10.If you are using a NAND flash memory device, specify the reserved block start address and the start address (including the option bits) within a 128-KB boundary. To specify the address, in the File/Data area column, select NAND flash Reserved Block and click Properties. 11.To generate programming files with either the typical or enhanced bitstream compression feature, or both, perform one of the following steps: Parallel Flash Loader IP Core User Guide Send Feedback Altera Corporation 26 UG-01082 2015.06.15 Constraining PFL Timing • Typical bitstream compression feature 1. Select .sof under SOF Data. 2. Click Properties, and then turn on the Compression option. 3. Click OK. • Enhanced bitstream compression feature 1. In the Options dialog box, turn on the Enable enhanced bitstream-compression when available option. 2. Click OK. • Double compression technique • Perform all the steps for the typical bitstream compression and enhanced bitstream compression features listed above. Note: For more information about the compression feature in the PFL IP core, refer to “Using Enhanced Bitstream Compression and Decompression”. 12.To generate programming files with encrypted data, select .sof under SOF Data and click Properties. Turn on the Generate encrypted bitstream check box. 13.Click OK to create the .pof. Related Information Using Enhanced Bitstream Compression and Decompression on page 18 Constraining PFL Timing The PFL IP core supports the Quartus II TimeQuest Timing Analyzer for accurate timing analysis on the Altera IP cores. To perform timing analysis, you must define the clock characteristics, external path delays, and timing exceptions for the PFL input and output ports. This section provides guidelines for defining this information for PFL input and output ports for use by the TimeQuest analyzer. Note: The TimeQuest analyzer is a timing analysis tool that validates the timing performance of the logic in the design using industry-standard constraint, analysis, and reporting methodology. For more information about the TimeQuest analyzer, refer to the Quartus II TimeQuest Timing Analyzer chapter in volume 3 of the Quartus II Handbook. Note: After you specify the timing constraint settings for the clock signal and for the asynchronous and synchronous input and output ports in the TimeQuest analyzer, on the Constraints menu, click Write SDC File to write all the constraints to a specific System Design Constraints File (.sdc). After the .sdc is written, run full compilation for the PFL design. Related Information Quartus II TimeQuest Timing Analyzer of Quartus II Handbook Provides more information about the TimeQuest analyzer. Constraining Clock Signal At any given time, one of the following two clock sources clocks the blocks and modules of the PFL IP core: • Clock signals from the pfl_clk ports of the PFL during FPGA configuration • TCK pins of the JTAG programming interface during flash programming Altera Corporation Parallel Flash Loader IP Core User Guide Send Feedback UG-01082 2015.06.15 Constraining Synchronous Input and Output Ports 27 The clock signal on the TCK pins is internally constrained to the maximum frequency supported by the selected JTAG programming hardware. It is not necessary to constrain the clock signal. You can constrain pfl_clk to the maximum frequency that the PFL IP core supports. You can use the create_clock command or the Create Clock dialog box to specify the period and duty cycle of the clock constraint. To constrain the pfl_clk signal in the TimeQuest analyzer, follow these steps: 1. Run full compilation for the PFL design. Ensure that the timing analysis tool is set to TimeQuest Timing Analyzer. 2. After full compilation completes, on the Tools menu, select TimeQuest Timing Analyzer to launch the TimeQuest analyzer window. 3. In the Tasks list, under Diagnostic, click Report Unconstrained Paths to view the list of unconstrained parts and ports of the PFL design. 4. In the Report list, under Unconstrained Paths, click Clock Summary to view the clock that requires constraints. The default setting for all unconstrained clocks is 1 GHz. To constrain the clock signal, right-click the clock name and select Edit Clock Constraint. 5. In the Create Clock dialog box, set the period and the duty cycle of the clock constraint. 6. Click Run. Constraining Synchronous Input and Output Ports The setup and hold time of synchronous input and output ports is critical to the system designer. To avoid setup and hold time violations, you can specify the signal delay from the FPGA or the flash memory device to the synchronous input and output ports of the PFL IP core. The Quartus II Fitter places and routes the input and output registers of the PFL IP core to meet the specified timing constraints. Note: For more information about the synchronous input and output ports of the PFL IP core, refer to PFL Timing Constraints table. The signal delay from FPGA or flash memory device to the PFL synchronous input port is specified by set_input_delay. The delay calculation is: Input delay value = Board delay from FPGA or flash output port to the PFL input port + TCO of the FPGA or flash memory device The signal delay from PFL synchronous output port to FPGA or flash memory device is specified by set_output_delay. The delay calculation is: Output delay value = Board delay from the PFL output port to the FPGA or flash input port + TSU of FPGA or flash device. Note: TCO is the clock-to-output time from the timing specification in the FPGA, CPLD or flash datasheet. Parallel Flash Loader IP Core User Guide Send Feedback Altera Corporation 28 UG-01082 2015.06.15 Constraining Asynchronous Input and Output Ports To constrain the synchronous input and output signals in the TimeQuest analyzer, follow these steps: 1. Run full compilation for the PFL design. Ensure that the timing analysis tool is set to TimeQuest Timing Analyzer. 2. After full compilation completes, on the Tools menu, select TimeQuest Timing Analyzer to launch the TimeQuest analyzer window. 3. In the Tasks list, under Diagnostic, click Report Unconstrained Paths to view the list of unconstrained parts and ports of the PFL design. 4. In the Report list, under the Unconstrained Paths category, select Setup Analysis, and then click Unconstrained Input Port Paths. 5. Right-click each synchronous input or output port in the From list or To list and select set_input_delay for the input port or set_output_delay for the output port, then specify the input delay or output delay value. Related Information Summary of PFL Timing Constraints on page 28 Constraining Asynchronous Input and Output Ports You can exclude asynchronous input and output ports from the timing analysis of the PFL IP core because the signals on these ports are not synchronous to a IP core clock source. The internal structure of the PFL IP core handles the metastability of these asynchronous signals. To exclude asynchronous input and output ports from the timing analysis, use the set_false_path command to ignore these ports during timing analysis. Note: After you specify all timing constraint settings for the clock signal, on the Constraints menu, click Write SDC File to write all the constraints to a specific .sdc. Then, run full compilation for the PFL design again. Summary of PFL Timing Constraints Table 7: PFL Timing Constraints Type Port Constraint Type Input clock pfl_clk create_clock pfl_nreset set_false_path — fpga_pgm set_false_path — fpga_conf_done set_false_path — fpga_nstatus set_false_path — pfl_flash_access_granted set_false_path — pfl_nreconfigure set_false_path — Input asynchro‐ nous Altera Corporation Delay Value Can be constrained up to the maximum frequency supported by the PFL IP core. Parallel Flash Loader IP Core User Guide Send Feedback UG-01082 2015.06.15 Simulating PFL Design Type Port Constraint Type Delay Value fpga_nconfig set_false_path — pfl_flash_access_request set_false_path — flash_nce set_false_path — flash_nwe set_false_path — flash_noe set_false_path — flash_addr set_false_path — Output asynchro‐ nous Bidirectional synchronous flash_data • Normal read mode: set_false_path • Burst read mode: set_input_delay Output synchro‐ nous fpga_data set_input_delay fpga_dclk set_input_delay 29 Burst read mode: Board delay from fpga_dclk pin of the CPLD to DCLK pin of the FPGA Board delay + TSU of the FPGA Board delay from fpga_dclk pin of the CPLD to DCLK pin of the FPGA Simulating PFL Design You can simulate the behavior of the PFL IP core with the ModelSim®-Altera software as it configures an FPGA. This section provides guidelines on the PFL simulation for FPGA configuration. Note: PFL simulation is based on functional netlist, and does not support gate-level simulation. PFL simulation does not reflect the true behavior of the hardware. Altera certifies the PFL IP core based on actual hardware testing, and not through PFL simulation. The PFL simulation only provides primitive behavioral simulation. Table 8: Files Required for PFL Simulation in the ModelSim-Altera Software File/Library Description .vo or .vho The Verilog HDL or VHDL output file of the PFL IP core. .sdo The Standard Delay Format Output file (.sdo) of the PFL IP core. Simulation libraries: The precompiled library files for Altera IP core primitives and Altera CPLDs in the ModelSim-Altera software. • • • • altera altera_mf maxii maxv Test bench Test bench file to establish the interface between the PFL IP core and the flash memory device. Flash simulation model files The simulation model files for the flash memory devices in the PS or FPP configuration. For the flash simulation model file for each flash memory device, refer to the respective flash memory device manufacturer. Parallel Flash Loader IP Core User Guide Send Feedback Altera Corporation 30 UG-01082 2015.06.15 Creating a Test Bench File for PFL Simulation Related Information • ModelSim-Altera Software Support Provides more information about simulation setup in ModelSim-Altera software. • Altera Knowledge Center Provides more information about known PFL simulation issues. • About Using the ModelSim Software with the Quartus II Software Provides more information about obtaining the .vo or .vho, .sdo, and simulation libraries in the ModelSim-Altera software. Creating a Test Bench File for PFL Simulation You can use a test bench file to establish the interface between the PFL IP core and the flash memory device. You must map the input and output ports of the PFL IP core to the appropriate data or address bus, and to the control signals of the flash. To perform the signal mapping, you must include the PFL primitive block and the flash primitive block in the test bench. The primitive blocks contain the input and output ports of the device. You can obtain the flash primitive blocks from the simulation model files provided by the flash memory device manufacturer. To establish the connection between the PFL IP core and the flash memory device, you must connect the flash data bus, the flash address bus, and the flash control signals from the PFL primitive block to the appropriate ports of the flash primitive block. Example 1: PFL Primitive Block pfl pfl_inst ( .fpga_pgm(<fpga_pgm source>), .pfl_clk(<pfl clock source>), .pfl_flash_access_granted(<pfl_flash_access_granted source>), .pfl_flash_access_request(<pfl_flash_access_granted destination>), .pfl_nreconfigure(<pfl_nreconfigure source>), .pfl_nreset(<pfl_nreset source>), .flash_addr(<flash address bus destination>), .flash_data(<flash_data bus destination>), .flash_nce(<flash_nce destination>), .flash_noe(<flash_noe destination>), .flash_nreset(<flash_nreset destination>), .flash_nwe(<flash_nwe destination>), .fpga_conf_done(<fpga_conf_done source>), .fpga_nstatus(<fpga_nstatus source>), .fpga_data(<fpga_data destination>), .fpga_dclk(<fpga_dclk destination>), .fpga_nconfig(<fpga_nconfig destination>), ); Note: For more information about the flash simulation model files, contact the flash memory device manufacturer. Performing PFL Simulation in the ModelSim-Altera Software To perform PFL simulation in the ModelSim-Altera software, you must specify the .sdo or load the ModelSim precompiled libraries listed in Files Required for PFL Simulation in the ModelSim-Altera Software table. Altera Corporation Parallel Flash Loader IP Core User Guide Send Feedback UG-01082 2015.06.15 Performing PFL Simulation for FPGA Configuration 31 Related Information • Simulating PFL Design on page 29 • About Using the ModelSim Software with the Quartus II Software Provides more information about obtaining the .vo or .vho, .sdo, and simulation libraries in the ModelSim-Altera software. Performing PFL Simulation for FPGA Configuration Before beginning the FPGA configuration, the PFL IP core reads the option bits stored in the option bits sector to obtain information about the .pof version used for flash programming, the start and end address of each page of the configuration image stored in the flash, and the Page-Valid bit. In this simulation example, the start and end addresses of the option bits sector are 0×800000 and 0×800080, respectively. The PFL IP core first reads from the final address, which is 0×800080, to obtain the .pof version information. Because fpga_pgm[2..0] is set to 000, the PFL IP core reads from address 0×800000 to address 0×800003 to get the start and end address of page 0 and the Page-Valid bit. The LSB in address 0×800000 is the Page-Valid bit. The Page-Valid bit must be 0 for the PFL IP core to proceed with FPGA configuration. While the PFL IP core reads from the flash, it asserts the active-low flash_nce and flash_noe signals, and asserts the active-high pfl_flash_access_request signal. Note: Before you perform the device configuration simulation, ensure that the PFL IP core receives the correct option bits address and associated values to guarantee correct simulation output. Figure 21: Simulation Before Configuration Figure shows the simulation when the PFL IP core reads the option bits from the flash memory device before configuration starts. Parallel Flash Loader IP Core User Guide Send Feedback Altera Corporation 32 UG-01082 2015.06.15 Programming Altera CPLDs and Flash Memory Devices After reading the option bits for page 0, the PFL IP core waits for a period of time before the configuration starts. The flash_data remains at 0×ZZ within this period. Configuration starts when the fpga_dclk starts to toggle. During configuration, the PFL IP core asserts the flash_nce and flash_noe signals low, and the pfl_flash_access_request signal high. Figure 22: Simulation When FPGA Configuration Starts The FPGA configuration continues until the fpga_conf_done signal is asserted high, which indicates the configuration is complete. After the configuration process completes, the PFL IP core pulls the flash_nce and flash_noe signals high and the pfl_flash_access_request signal low to indicate the configuration data is no longer being read from the flash memory device. Programming Altera CPLDs and Flash Memory Devices Using the Quartus II Programmer, you can program Altera CPLDs and flash memory device in a single step or separate steps. To program both in a single step, first program the CPLD, then the flash memory device. Follow these steps: 1. 2. 3. 4. Altera Corporation Open the Quartus II Programmer window and click Add File to add the .pof for the CPLD. Right-click the CPLD .pof and click Attach Flash Device. In the Flash Device menu, select the density of the flash memory device to be programmed. Right-click the necessary flash memory device density and click Change File. Parallel Flash Loader IP Core User Guide Send Feedback UG-01082 2015.06.15 Programming Altera CPLDs and Flash Memory Devices Separately 33 5. Select the .pof generated for the flash memory device. The .pof for the flash memory device is attached to the .pof of the CPLD. 6. Add other programming files if your chain has other devices. 7. Check all the boxes in the Program/Configure column for the new .pof and click Start to program the CPLD and flash memory device. The Quartus II Programmer allows you to program, verify, erase, blank-check, or examine the configuration data page, the user data page, and the option bits sector separately, provided the CPLD contains the PFL IP core. Note: The Quartus II programmer erases the flash memory device if you select the .pof of the flash memory device before programming. To prevent the Quartus II Programmer from erasing other sectors in the flash memory device, select only the pages, .hex data, and option bits. Programming Altera CPLDs and Flash Memory Devices Separately To program the CPLD and the flash memory devices separately, follow these steps: 1. 2. 3. 4. 5. 6. Open the Quartus II Programmer window. Click Add File. The Add Programming File Window dialog box appears. Add the targeted .pof, and click OK. Check the boxes under the Program/Configure column of the .pof. Click Start to program the CPLD. After the programming progress bar reaches 100%, click Auto Detect. For example, if you are using dual P30 or P33, the programmer window shows a dual P30 or P33 chain in your setup. Alternatively, you can add the flash memory device to the programmer manually. Right-click the CPLD .pof and click Select Flash Device. In the Select Flash Device dialog box, select the device of your choice. 7. Right-click the necessary flash memory device density and click Change File. Note: You must select the density that is equivalent to the sum of the density of two CFI or NAND flash memory devices. For example, if you require two 512-Mb CFI flash memory devices, then select CFI 1 Gbit. For more than one quad SPI flash memory device, select the density that is equivalent to the sum of all the density of the quad SPI flash memory devices. For example, a four quad SPI flash memory devices (128 Mb for each device), the total density is equivalent to 512 Mb. A .pof with 512-Mb flash density is required to program these quad SPI flash devices. The PFL IP core handles the 512-Mb .pof programming to the four quad SPI flash memory devices. 8. Select the .pof generated for the flash memory device. The .pof for the flash memory device is attached to the .pof of the CPLD. 9. Check the boxes under the Program/Configure column for the added .pof and click Start to program the flash memory devices. Defining New CFI Flash Device The PFL IP core supports Intel-compatible and AMD-compatible flash memory devices. In addition to the supported flash memory devices, you can define the new Intel- or AMD-compatible CFI flash memory device in the PFL-supported flash database using the Define new CFI flash memory device feature. Parallel Flash Loader IP Core User Guide Send Feedback Altera Corporation 34 UG-01082 2015.06.15 Defining New CFI Flash Device To add a new CFI flash memory device to the database or update a CFI flash device in the database, follow these steps: 1. In the Programmer window, on the Edit menu, select Define New CFI Flash Device. The Define CFI Flash Device window appears. The following table lists the three functions available in the Define CFI Flash Device window. Table 9: Functions of the Define CFI Flash Device Feature Function Description New Add new Intel- or AMD-compatible CFI flash memory device into the PFLsupported flash database. Edit Edit the parameters of the newly added Intel- or AMD-compatible CFI flash memory device in the PFL-supported flash database. Remove Remove the newly added Intel- or AMD-compatible CFI flash memory device from the PFL-supported flash database. 2. To add a new CFI flash memory device or edit the parameters of the newly added CFI flash memory device, select New or Edit. The New CFI Flash Device dialog box appears. 3. In the New CFI Flash Device dialog box, specify or update the parameters of the new flash memory device. You can obtain the values for these parameters from the datasheet of the flash memory device manufacturer. Table 10: Parameter Settings for New CFI Flash Device Parameter Description CFI flash device name Define the CFI flash name CFI flash device ID Specify the CFI flash identifier code CFI flash manufacturer ID Specify the CFI flash manufacturer identification number CFI flash extended device ID Specify the CFI flash extended device identifier, only applicable for AMD-compatible CFI flash memory device Flash device is Intel compatible Turn on the option if the CFI flash is Intel compatible Typical word programming time Typical word programming time value in µs unit Maximum word programming time Maximum word programming time value in µs unit Typical buffer programming time Typical buffer programming time value in µs unit Maximum buffer programming time Maximum buffer programming time value in µs unit Note: You must specify either the word programming time parameters, buffer programming time parameters, or both. Do not leave both programming time parameters with the default value of zero. 4. Click OK to save the parameter settings. 5. After you add, update, or remove the new CFI flash memory device, click OK. Altera Corporation Parallel Flash Loader IP Core User Guide Send Feedback UG-01082 2015.06.15 Programming Multiple Flash Memory Devices 35 Related Information Supported Flash Memory Devices on page 2 Programming Multiple Flash Memory Devices The PFL IP core supports multiple-flash programming of as many as 16 flash memory devices. This feature allows the PFL IP core to connect to multiple flash memory devices to perform flash programming sequentially. PFL multiple-flash programming supports both speed and area mode flash programming. For FPGA configuration, use the content in the flash memory device that connects to the nCE[0] pin as configuration data. To use the multiple flash programming feature, follow these steps: 1. Select the number of flash memory devices connected to the CPLD in the PFL IP core parameter editor. 2. Connect the nCE pins of the PFL to the nCE pins of the flash memory device in the block diagram. Compile the design. 3. Click Auto Detect in the Quartus II programmer. The CPLD appears as the main item, followed by a list of CFI flash memory devices detected as secondary items in the device tree. 4. Attach the flash memory device .pof to each flash memory device. 5. Check the boxes in the Quartus II Programmer for the necessary operation and click Start. Creating Jam Files for Altera CPLDs and Flash Memory Device Programming To use .jam files to program the CPLD and flash memory device, follow these steps: 1. 2. 3. 4. 5. Open the Quartus II Programmer window and click Add File to add the .pof for the CPLD. Right-click the CPLD .pof and click Attach Flash Device. In the Flash Device menu, select the density of the flash memory device to be programmed. Right-click the necessary flash memory device density and click Change File. Select the .pof generated for the flash memory device. The .pof for the flash memory device is attached to the .pof of the CPLD. 6. On the File menu, point to Create/Update and click Create JAM, JBC, SVF, or ISF File. 7. Enter a name and select the file format (.jam). 8. Click OK. Note: Use the .jam files with the Quartus II Programmer or quartus_jli executable file. Related Information AN425: Using the Command-Line Jam STAPL Solution for Device Programming. Provides more information about the quartus_jli executable. PFL IP Core In Embedded Systems The PFL IP core allows processors, such as the Nios® II processor, to access the flash memory device while programming flash and configuring an FPGA. The following figure shows how you can use the PFL IP core to program the flash memory device and to configure the FPGA with a Nios II processor. The configured Nios II processor uses the non-configura‐ tion data stored in the same flash memory device. Parallel Flash Loader IP Core User Guide Send Feedback Altera Corporation 36 UG-01082 2015.06.15 PFL IP Core In Embedded Systems Figure 23: Single-Device Configuration Using the PFL With the Controller VCC (1) VCC (1) VCC (1) VCC CFI Flash VCC nRP nWP 10kΩ Altera CPLD 10kΩ 10kΩ Altera FPGA pfl_nreset pfl_flash_access_granted pfl_flash_access_request fpga_conf_done flash_addr fpga_nstatus flash_data fpga_nconfig flash_nwe fpga_data(2) flash_nce fpga_dclk flash_noe ADDR DATA nWE nCE nOE WP#/ACC BYTE# CONF_DONE nSTATUS nCONFIG DATA DCLK nCE nCEO NC (3) Nios II Processor Interface (4) flash_access_request flash_access_granted ext_ram_bus_addr ext_ram_bus_data write_n_to_ext_flash chip_n_to_ext_flash output_n_to_ext_flash WP#/ACC BYTE# (1) You must connect the pull-up resistor to a supply that provides an acceptable input signal for the devices. V CC must be high enough to meet the VIH specification of the I/O on both devices. For example, the Stratix II V IH specification ranges from 1.7 to 3.3 V; therefore, the supply for the pull-up resistor, V CC, must be within 1.7 to 3.3 V to meet the VIH specification. (2) For PS configuration mode, this is a 1-bit data line. For FPP configuration mode, this is an 8-bit data bus. (3) Do not connect anything to the NC pin (the no connect pin), not even VCC or GND. (4) You can use the Nios II processor in other Altera FPGA, except when you are configuring the FPGA. Figure 24: Relationship Between the Four Sections in the Design Example CFI Flash Memory Common Flash Interface Altera CPLD PFL pfl_flash_access_granted pfl_flash_access_request Altera FPGA with NIOS II Processor You must configure the Altera FPGA with the Nios II processor when you power up the board. You can store the Nios II processor image in the flash memory device and use the PFL IP core to configure the image to the Altera FPGA. If you store the Nios II processor image in the same flash memory device you Altera Corporation Parallel Flash Loader IP Core User Guide Send Feedback UG-01082 2015.06.15 PFL IP Core In Embedded Systems 37 intend to program, do not overwrite the Nios II processor image when you program the flash memory device with other user data. If you do not want to store the image in the flash memory device, you can store the Nios II image in a different storage device, for example an enhanced configuration (EPC) device or an erasable program‐ mable configurable serial (EPCS) memory. In Relationship Between the Four Sections in the Design Example figure above, the Nios II processor and the PFL IP core share the same bus line to the flash memory device. However, to avoid data contention, the processor and the IP core cannot access or program the flash memory device at the same time. To ensure that only one controller (the processor or the IP core), is accessing the flash memory device at any given time, you must tri-state all output pins from one controller to the flash memory device, while the other controller is accessing the flash memory device using the pfl_flash_access_request and pfl_flash_access_granted pins in the PFL IP core. Table 11: PFL Flash Access Pins and Functions Pin Description pfl_flash_access_request pfl_flash_access_granted The PFL IP core drives this pin high to request access to the flash memory device. The PFL IP core enables the access to the flash memory device whenever the PFL IP core receives a high input signal at this pin. Table 12: pfl_flash_access_request and pfl_flash_access_granted Pins With the Nios II and PFL IP Core Table lists the methods to use the pfl_flash_access_request and pfl_flash_access_granted pins to ensure both processors are not accessing the flash memory device at the same time. Signal High output signal at pfl_flash_access_ request Low output signal at pfl_flash_access_ request Nios II Processor PFL IP Core Tri-state all output pins to Connect all input and output pins to the flash the flash memory device. memory device when the pfl_flash_access_ granted pin receives a high input. Reconnect all pins to the flash memory device. Tri-state all output pins to the flash memory device when the pfl_flash_access_granted pin receives a low input. Note: The Set bus pins to tri-state when not in use option for the PFL IP core disables the PFL IP core whenever the pfl_flash_access_granted pin is pulled low. Parallel Flash Loader IP Core User Guide Send Feedback Altera Corporation 38 UG-01082 2015.06.15 PFL IP Core In Embedded Systems Figure 25: Nios II Processor and PFL Accessing the Flash Memory Device Sequence Nios II processor connects to the flash device By default, the Nios II processor is connected to the flash device. All PFL megafunction output pins are tri-stated. PFL megafunction requests access to flash device The PFL megafunction pulls the pfl_flash_access_request pin high to request access to the flash device. Nios II processor releases the flash device The Nios II processor tri-states all output pins to the flash device and routes the output of pfl_flash_access_request to pfl_flash_access _granted. PFL megafunction accesses the flash device The PFL megafunction accesses the flash device after receiving a high input at the pfl_flash_access_granted input pin. The pfl_flash_access_request pin stays high as long as the PFL megafunction is connected to the flash device. PFL megafunction releases the flash device The PFL megafunction pulls the pfl_flash_access_request output pin low after accessing the flash device. Note: Altera recommends that you enable the safe state machine setting to prevent the PFL IP core from entering an undefined state. To set this option, on the Assignments menu, click Settings. In the Settings dialog box, on the Analysis and Synthesis page, click More Settings, and select safe state machine. The Altera CPLD and Nios II processor can each program the CFI flash memory device individually. To prevent both processors from accessing the CFI flash memory device at the same time, the flash_access_granted and flash_access_request pins of the CPLD and Nios II processor are connected together. To use other processors or controllers in place of the Nios II processor, ensure that the pfl_flash_access_granted and pfl_flash_access_request pins of the PFL IP core connect to your processor using the method in pfl_flash_access_request and pfl_flash_access_granted Pins With the Nios II and PFL IP Core table above. You must also specify the flash memory device read or write access time for your processor or controller. To avoid data contention when the PFL IP core is accessing the flash memory device, ensure that the output pins from your processor are tri-stated when the pfl_flash_access_request signal is high. Related Information Nios II Processor Reference Handbook Provides more information about the Nios II processor. Altera Corporation Parallel Flash Loader IP Core User Guide Send Feedback UG-01082 2015.06.15 Third-party Programmer Support 39 Third-party Programmer Support You can program the flash memory using a third-party programmer instead of using Parallel Flash Loader IP core. To program using third-party programmer, you need to convert the .pof to an .rbf by following the steps below: 1. Compile and generate a .pof file for the flash memory device. 2. Convert .pof file to .hexout file using the following command: quartus_cpf -c <pof_file_base_name>.pof <hex_file_base_name>.hexout 3. Convert .hexout file created above to .rbf using the nios2-elf-objcopy command on Nios II Command Shell: nios2-elf-objcopy –I ihex –O binary <input file>.hexout <output file>.rbf Related Information • Programming Flash Memory on page 9 • NIOS II Command-Line Tools Provides more information on the nios2-elf-objcopy command. Parameters This section contains information about the GUI parameters of the PFL IP core. Table 13: PFL Parameters Options Value Description General Operating mode • Flash Programming and FPGA Configuration • Flash Programming • FPGA Configuration Specifies the operating mode of flash program‐ ming and FPGA configuration control in one IP core or separate these functions into individual blocks and functionality. Targeted flash device • • • • Specifies the flash memory device connected to the PFL IP core. Tri-state flash bus On or Off CFI Parallel Flash Altera Active Serial ×4 Quad SPI Flash NAND Flash Allows the PFL IP core to tri-state all pins interfacing with the flash memory device when the PFL IP core does not require an access to the flash memory. Flash Interface Setting Parallel Flash Loader IP Core User Guide Send Feedback Altera Corporation 40 UG-01082 2015.06.15 Parameters Options Value Number of flash devices used • • • • Largest flash density • CFI Parallel Flash: 8 Mbit–4 Gbit • NAND Flash: 512 Mbit/2 Gbit - Micron(NAND) • 1 Gbit - Micron (MT29) Description Specifies the number of flash memory devices CFI Parallel Flash: 1–16 connected to the PFL IP core. Allows up to four Altera Active Serial ×4: 1,2,4 flash memory devices. Quad SPI Flash: 1,2,4 NAND Flash: 1,2,4 Specifies the density of the flash memory device to be programmed or used for FPGA configuration. If you have more than one flash memory device connected to the PFL IP core, specify the largest flash memory device density. For CFI flash, select the density that is equivalent to the sum of the density of two CFI flashes. For example, if you use two 512-Mb CFI flashes, you must select CFI 1 Gbit. (Available only if you select CFI Parallel Flash or NAND Flash.) Flash interface data • CFI Parallel Flash: 8, 16, or width 32 bits • NAND Flash: 8 bits or 16 bits Specifies the flash data width in bits. The flash data width depends on the flash memory device you use. For multiple flash memory device support, the data width must be the same for all connected flash memory devices. For CFI flash, select the flash data width that is equivalent to the sum of the data width of two CFI flashes. For example, if you are targeting dual P30 or P33 solution, you must select 32 bits because each CFI flash data width is 16 bits. (Available only if you select CFI Parallel Flash or NAND Flash.) User control flash_nreset pin On or Off Creates a flash_nreset pin in the PFL IP core to connect to the reset pin of the flash memory device. A low signal resets the flash memory device. In burst mode, this pin is available by default. When using a Spansion GL flash device, connect this pin to the RESET# pin of the flash device. (Available only if you select CFI Parallel Flash.) Quad SPI flash device manufac‐ turer • Macronix • Micron • Spansion Specifies the device manufacturer of the quad SPI flash. (Available only if you select Quad SPI Flash.) Quad SPI flash device density 8 Mbit–256 Mbit Specifies the density of the quad SPI flash to be programmed or used for FPGA configuration. (Available only if you select Quad SPI Flash.) Altera Corporation Parallel Flash Loader IP Core User Guide Send Feedback UG-01082 2015.06.15 Parameters Options Byte address for reserved block area Value — 41 Description Specifies the start address of the reserved block area for bad block management. NAND flash memory may contain bad blocks that contain one or more invalid bits. The reserve blocks replace any bad blocks that the PFL IP core encounters. Altera recommends that you reserve a minimum of 2% of the total block. (Available only if you select NAND Flash.) On-die ECC support On or Off Enables the support for on-die ECC. Certain NAND flash memory devices has on-die ECC. Allows the PFL IP core to use the on-die ECC of the flash memory device. Turning off this option allows the PFL IP core to generate its own ECC engine. (Available only if you select NAND Flash.) Flash Programming Flash programming Area, Speed IP optimization Specifies the flash programming IP optimization. If you optimize the PFL IP core for speed, the flash programming time is shorter but the IP core uses more LEs. If you optimize the PFL IP core for area, the IP core uses less LEs, but the flash program‐ ming time is longer. (Available only if you select CFI Parallel Flash.) FIFO size Specifies the FIFO size if you select Speed for flash programming IP optimization. The PFL IP core uses additional LEs to implement FIFO as temporary storage for programming data during flash programming. With a larger FIFO size, programming time is shorter. (Available only if you select CFI Parallel Flash.) — Add Block-CRC On or Off verification acceler‐ ation support Adds a block to accelerate verification. (Available only if you select CFI Parallel Flash.) FPGA Configuration External clock frequency — Parallel Flash Loader IP Core User Guide Send Feedback Specifies the user-supplied clock frequency for the IP core to configure the FPGA. The clock frequency must not exceed two times the maximum clock (DCLK) frequency acceptable by the FPGA for configuration. The PFL IP core can divide the frequency of the input clock maximum by two. Altera Corporation 42 UG-01082 2015.06.15 Parameters Options Flash access time Value — Description Specifies the access time of the flash. You can get the maximum access time that a flash memory device requires from the flash datasheet. Altera recommends specifying a flash access time that is the same as or longer than the required time. For CFI parallel flash, the unit is in ns and for NAND flash, the unit is in us. NAND flash uses page instead of byte, and requires more access time. This option is disabled for quad SPI flash. Option bits byte address — Specifies the start address in which the option bits are stored in the flash memory. The start address must reside on an 8-KB boundary. See related for more information about option bits. FPGA configura‐ tion scheme • PS • FPP • FPP ×16 (for Stratix V devices) • FPP ×32(for Stratix V devices) Configuration failure response options Halt, Retry same page, or Retry Configuration behavior after configuration failure. from fixed address • If you select Halt, the FPGA configuration stops completely after failure. • If you select Retry same page, after failure, the PFL IP core reconfigures the FPGA with data from the same page of the failure. • If you select Retry from fixed address, the PFL IP core reconfigures the FPGA with data from a fixed address in the next option field after failure. Byte address to retry from on configuration failure — If you select Retry from fixed address for configu‐ ration failure option, this option specifies the flash address for the PFL IP core to read from the reconfiguration for a configuration failure. Include input to force reconfigura‐ tion On or Off Includes an optional reconfiguration input pin (pfl_nreconfigure) to enable a reconfiguration of the FPGA. Watchdog timer On or Off Enables a watchdog timer for remote system upgrade support. Turning on this option enables the pfl_reset_watchdog input pin and pfl_ watchdog_error output pin, and specifies the time period before the watchdog timer times out. This watchdog timer is a time counter which runs at the pfl_clk frequency. Altera Corporation Select the FPGA configuration scheme. The default FPP is FPP ×8. If you are using Stratix V devices, two additional FPP mode is available: FPP ×16 and FPP ×32. Parallel Flash Loader IP Core User Guide Send Feedback UG-01082 2015.06.15 Parameters Options Value Description Time period before — the watchdog timer times out Specifies the time out period of the watchdog timer. The default time out period is 100 ms Ratio between input 1, 2, 4, or 8 clock and DCLK output clock Specifies the ratio between the input clock and DCLK. Use advance read mode • Normal Mode • Intel Burst Mode (P30 or P33) • Spansion Page Mode (GL) • Micron Burst Mode (M58BW) 43 • Ratio 8 means every eight external clocks to pfl_clk generate one fpga_dclk. • Ratio 4 means every four external clocks to pfl_clk generate one fpga_dclk. • Ratio 2 means every two external clocks to pfl_clk generate one fpga_dclk. • Ratio 1 means every one external clock to pfl_ clk generate one fpga_dclk. An option to improve the overall flash access time for the read process during the FPGA configura‐ tion. • Normal mode—Applicable for all flash memory • Intel Burst mode—Applicable for Micron P30 and P33 flash memory only. Reduces sequential read access time • Spansion page mode—Applicable for Spansion GL flash memory only • Micron burst mode—Applicable for Micron M58BW flash memory only For more information about the read-access modes of the flash memory device, refer to the respective flash memory data sheet. Enhanced bitstream • None decompression • Area • Speed Select to enable or disable the enhanced bitstream decompression block. • If you select None, the core disables the enhanced bitstream decompression block. • If you select Area, the core optimizes the logic resources used by the enhanced bitstream decompression block in the PFL IP core. • If you select Speed, the core optimizes the speed of the data decompression. You can only optimize speed if you select FPP as the FPGA configuration scheme. Related Information • Storing Option Bits on page 15 • Configuration Handbook Provides more information about pull-up configuring pins for specific Altera FPGA families Parallel Flash Loader IP Core User Guide Send Feedback Altera Corporation 44 UG-01082 2015.06.15 Signals Signals This section contains information about the PFL IP core input and output signals. Table 14: PFL Signals For maximum FPGA configuration DCLK frequencies, refer to the Configuration Handbook. Pin Description Weak PullUp pfl_nreset Input — Asynchronous reset for the PFL IP core. Pull high to enable FPGA configuration. To prevent FPGA configuration, pull low when you do not use the PFL IP core. This pin does not affect the flash programming functionality of the PFL IP core. pfl_flash_access_granted Input — Used for system-level synchronization. This pin is driven by a processor or any arbitrator that controls access to the flash. This activehigh pin is connected permanently high if you want the PFL IP core to function as the flash master. Pulling the pfl_flash_ access_granted pin low prevents the JTAG interface from accessing the flash and FPGA configuration. pfl_clk Input — User input clock for the device. Frequency must match the frequency specified in the IP core and must not be higher than the maximum DCLK frequency specified for the specific FPGA during configuration. This pins are not available for the flash program‐ ming option in the PFL IP core. fpga_pgm[] Input — Determines the page for the configuration. This pins are not available for the flash programming option in the PFL IP core. fpga_conf_done Input Altera Corporation Function 10-kW Pull- Connects to the CONF_DONE pin of the FPGA. Up Resistor The FPGA releases the pin high if the configuration is successful. During FPGA configuration, this pin remains low. This pins are not available for the flash program‐ ming option in the PFL IP core. Parallel Flash Loader IP Core User Guide Send Feedback UG-01082 2015.06.15 Signals Pin Weak PullUp Function fpga_nstatus Input pfl_nreconfigure Input — A low signal at this pin initiates FPGA reconfiguration. You can reconnect this pin to a switch for more flexibility to set this input pin high or low to control FPGA reconfiguration. When FPGA reconfigura‐ tion is initiated, the fpga_nconfig pin is pulled low to reset the FPGA device. The pfl_clk. pin registers this signal. This pins are not available for the flash programming option in the PFL IP core. pfl_flash_access_request Output — Used for system-level synchronization. When necessary, this pin connects to a processor or an arbitrator. The PFL IP core drives this pin high when the JTAG interface accesses the flash or the PFL IP core configures the FPGA. This output pin works in conjunction with the flash_noe and flash_nwe pins. flash_addr[] Output — Address inputs for memory addresses. The width of the address bus line depends on the density of the flash memory device and the width of the flash_data bus. The output of this pin depends on the setting of the unused pins if you did not select the PFL interface tri-state option when the PFL is not accessing the flash memory device. Input or Output (bidirection al pin) — Data bus to transmit or receive 8- or 16-bit data to or from the flash memory in parallel. The output of this pin depends on the setting of the unused pins if you did not select the PFL interface tri-state option when the PFL is not accessing the flash memory device. (8) flash_data[] (8) Description 45 10-kW Pull- Connects to the nSTATUS pin of the FPGA. Up Resistor This pin must be released high before the FPGA configuration and must stay high throughout FPGA configuration. If a configuration error occurs, the FPGA pulls this pin low and the PFL IP core stops reading the data from the flash memory device. This pins are not available for the flash programming option in the PFL IP core. Altera recommends not inserting logic between the PFL pins and the CPLD I/O pins, especially on the flash_data and fpga_nconfig pins. Parallel Flash Loader IP Core User Guide Send Feedback Altera Corporation 46 UG-01082 2015.06.15 Signals Pin Description Weak PullUp flash_nce[] Output — Connects to the nCE pin of the flash memory device. A low signal enables the flash memory device. Use this pin for multiple flash memory device support. The flash_ nce pin is connected to each nCE pin of all the connected flash memory devices. The width of this port depends on the number of flash memory devices in the chain. flash_nwe Output — Connects to the nWE pin of the flash memory device. A low signal enables write operation to the flash memory device. flash_noe Output — Connects to the nOE pin of the flash memory device. A low signal enables the outputs of the flash memory device during a read operation. flash_clk Output — Used for burst mode. Connects to the CLK input pin of the flash memory device. The active edges of CLK increment the flash memory device internal address counter. The flash_clk frequency is half of the pfl_ clk frequency in burst mode for single CFI flash. In dual P30 or P33 CFI flash solution, the flash_clk frequency runs at a quarter of the pfl_clk frequency. Use this pin for burst mode only. Do not connect these pins from the flash memory device to the CPLD device if you are not using burst mode. flash_nadv Output — Used for burst mode. Connects to the address valid input pin of the flash memory device. Use this signal for latching the start address. Use this pin for burst mode only. Do not connect these pins from the flash memory device to the CPLD device if you are not using burst mode. flash_nreset Output — Connects to the reset pin of the flash memory device. A low signal resets the flash memory device. fpga_data[] Output — Data output from the flash to the FPGA device during configuration. For PS mode, this is a 1-bit bus fpga_data[0] data line. For FPP mode, this is an 8-bit fpga_ data[7..0] data bus. This pins are not available for the flash programming option in the PFL IP core. Altera Corporation Function Parallel Flash Loader IP Core User Guide Send Feedback UG-01082 2015.06.15 Signals Pin fpga_dclk fpga_nconfig Description Weak PullUp Output — 47 Function Connects to the DCLK pin of the FPGA. Clock input data to the FPGA device during configuration. This pins are not available for the flash programming option in the PFL IP core. Open Drain 10-kW Pull- Connects to the nCONFIG pin of the FPGA. A Output Up Resistor low pulse resets the FPGA and initiates configuration. This pins are not available for the flash programming option in the PFL IP core. (8) flash_sck[] Output — Clock source for flash data read operation. Connects to the CLK input pin of the quad SPI flash. If you use more than one quad SPI flash, connect this pin to the CLK input of all the quad SPI flashes. The width of the port is equivalent to the number of quad SPI flash in the chain. flash_ncs[] Output — Connects to the ncs pin of the quad SPI flash. If you use more than one quad SPI flash, connect this pin to the ncs pin of all the quad SPI flashes. The width of this port is equivalent to the number of quad SPI flashes in the chain. flash_io0[] Output — The first bit of the data bus to or from the quad SPI flash. If you use more than one quad SPI flash, connect this pin to the first bit of the data bus of all the quad SPI flashes. The width of this port is equivalent to the number of quad SPI flashes in the chain. flash_io1[] Output — The second bit of the data bus to or from the quad SPI flash. If you use more than one quad SPI flash, connect this pin to the second bit of the data bus of all the quad SPI flashes. The width of this port is equivalent to the number of quad SPI flashes in the chain. flash_io2[] Output — The third bit of the data bus to or from the quad SPI flash. If you use more than one quad SPI flash, connect this pin to the third bit of the data bus of all the quad SPI flashes. The width of this port is equivalent to the number of quad SPI flashes in the chain. Parallel Flash Loader IP Core User Guide Send Feedback Altera Corporation 48 UG-01082 2015.06.15 Specifications Pin Description Weak PullUp Output — The fourth bit of the data bus to or from the quad SPI flash. If you use more than one quad SPI flash, connect this pin to the fourth bit of the data bus of all the quad SPI flashes. The width of this port is equivalent to the number of quad SPI flashes in the chain. pfl_reset_watchdog Input — A toggle signal to reset the watchdog timer before the watchdog timer times out. Hold the signal high or low for at least two clock cycles of the pfl_clk frequency to correctly reset the watchdog timer. pfl_watchdog_error Output — A high signal indicates an error to the watchdog timer. flash_io3[] Function Related Information Configuration Handbook Provides more information about pull-up configuring pins for specific Altera FPGA families Specifications This section provides the equations to estimate the time for reconfiguring the FPGA with the PFL IP core. The equations in the following table assume the following definitions: • Cflash is the number of clock cycles required to read from flash memory. • Ccfg is the number of input clock cycles to clock out the data (producing between one and 16 DCLK cycles, depending on the choice of flash data bus width and FPP or PS mode). Only the larger number between Cflash and Ccfg is important because reading from the flash and clocking out the data for configuration are performed in parallel. • Fclk is the input clock frequency to the PFL IP core. • Taccess is the flash access time. • Caccess is the number of clock cycles required before the data from the flash is ready. • Tpage_access is the page read time for Spansion flash memory devices and is only applicable for page mode access. Tpage_access is set to 30 ns in the PFL IP core. • N is the number of bytes to be clocked out. This value is obtained from the .rbf for the specific FPGA. Altera Corporation Parallel Flash Loader IP Core User Guide Send Feedback UG-01082 2015.06.15 Specifications 49 Table 15: FPP and PS Mode Equations for the PFL Flash Access Mode Configura‐ tion Data Option Flash Data Width (bits) 8 Normal Normal Mode/Page Mode (10) 8 Compressed and/or encrypted (9) 16 16 DCLK Ratio = 1, 2, 4, or 8 (9) FPP Mode PS Mode Cflash = Caccess Cflash = Caccess Ccfg = DCLK Ratio Ccfg = 8*DCLK Ratio Coverhead = 5*Caccess Coverhead = 5*Caccess Cflash = Caccess/2 Cflash = Caccess/2 Ccfg = DCLK Ratio Ccfg = 8*DCLK Ratio Coverhead = 3*Caccess Coverhead = 3*Caccess Cflash = Caccess Cflash = Caccess Ccfg = 4*DCLK Ratio Ccfg = 8*DCLK Ratio Coverhead = 5*Caccess Coverhead = 5*Caccess Cflash = Caccess/2 Cflash = Caccess/2 Ccfg = 4*DCLK Ratio Ccfg = 8*DCLK Ratio Coverhead = 3*Caccess Coverhead = 3*Caccess Ratio between input clock and DCLK output clock. For more information, see related information Parallel Flash Loader IP Core User Guide Send Feedback Altera Corporation 50 UG-01082 2015.06.15 Specifications Flash Access Mode Configura‐ tion Data Option 4 8 Normal 16 Burst Mode 4 Compressed and/or encrypted 8 16 (9) DCLK Ratio = 1, 2, 4, or 8 (9) Flash Data Width (bits) FPP Mode PS Mode Cflash = 4 Cflash = 4 Ccfg = DCLK Ratio Ccfg = 8*DCLK Ratio Coverhead = 48 Coverhead = 48 Cflash = 2 Cflash = 2 Ccfg = DCLK Ratio Ccfg = 8*DCLK Ratio Coverhead = 22*Caccess+8 Coverhead = 22*Caccess+8 Cflash = 1 Cflash = 1 Ccfg = DCLK Ratio Ccfg = 8*DCLK Ratio Coverhead = 20*Caccess+8 Coverhead = 20*Caccess+8 Cflash = 4 Cflash = 4 Ccfg = 4*DCLK Ratio Ccfg = 8*DCLK Ratio Coverhead = 48 Coverhead = 48 Cflash = 2 Cflash = 2 Ccfg = 4*DCLK Ratio Ccfg = 8*DCLK Ratio Coverhead = 22*Caccess+8 Coverhead = 22*Caccess+8 Cflash = 1 Cflash = 1 Ccfg = 4*DCLK Ratio Ccfg = 8*DCLK Ratio Coverhead = 20*Caccess+8 Coverhead = 20*Caccess+8 Ratio between input clock and DCLK output clock. For more information, see related information Altera Corporation Parallel Flash Loader IP Core User Guide Send Feedback UG-01082 2015.06.15 Specifications Flash Access Mode Configura‐ tion Data Option Flash Data Width (bits) 51 DCLK Ratio = 1, 2, 4, or 8 (9) FPP Mode PS Mode • For Normal Mode and Burst Mode: Caccess = Taccess*Fclk+1 Total Clock Cycles (from nRESET asserted high to N bytes of data clocked out) = Coverhead + max(Cflash, Ccfg)*N Total Configuration Time = Total Clock Cycle/ PFL Input Clock • For Page Mode Caccess =[(Taccess*Fclk+1) + (Tpage_access*Fclk*15)]/16 Total Clock Cycles (from nRESET asserted high to N bytes of data clocked out) = Coverhead + max (Cflash, Ccfg)*N Total Configuration Time = Total Clock Cycle/ PFL Input Clock • For FPP (×8) Total Clock Cycles (from nRESET asserted high to N bytes of data clocked out) Cflash remains the same • For FPP (×16) Total Clock Cycles (from nRESET asserted high to N word of data clocked out) Cflash = Cflash × 2 (×2 of Cflash from FPP ×8) • For FPP (×32) Total Clock Cycles (from nRESET asserted high to N double word of data clocked out) Cflash = Cflash × 4 (×4 of Cflash from FPP ×8) Configuration Time Calculation Examples The following are the configuration time calculation examples for normal mode, page mode, and burst mode: Note: Any reference to the core clock speed of 100 MHz is only an example of the configuration time calculation and not a recommendation of the actual clock. (9) (10) Ratio between input clock and DCLK output clock. For more information, see related information Spansion page mode support is only available in the Quartus II software versions 8.0 onwards. Parallel Flash Loader IP Core User Guide Send Feedback Altera Corporation 52 UG-01082 2015.06.15 Specifications Example 2: Normal Mode • Normal mode configuration time calculation: .rbf size for EP2S15 = 577KB = 590,848 Bytes Configuration mode = FPP without data compression or encryption Flash access mode = Normal Mode Flash data bus width = 16 bits Flash access time = 100 ns PFL input Clock = 100 MHz DCLK ratio = 2 • Use the following formulas in this calculation: Caccess = Taccess*Fclk+1 Cflash for Normal Mode = Caccess / 2 Ccfg = 2.5 Coverhead = 3*Caccess Total Clock Cycles = Coverhead + max (Cflash, Ccfg)*N Total Configuration Time = Total Clock Cycle/ PFL Input Clock • Substitute these values in the following formulas: Caccess = (100ns * 100MHz) + 1 = 11 Cflash = 11/2 = 5.5 Ccfg = 2.5 Coverhead = 3*11 = 33 Total Clock Cycles = 33 + 5.5 * 590848 = 3249697 Total Configuration Time at 100 MHz = 3249697/ 100 × 106 = 32.5ms Altera Corporation Parallel Flash Loader IP Core User Guide Send Feedback UG-01082 2015.06.15 Specifications 53 Example 3: Page Mode • Page mode configuration time calculation: .rbf size for EP2S15 = 577 KB = 590,848 Bytes Configuration mode = FPP without data compression or encryption Flash access mode = Page Mode Flash data bus width = 16 bits Flash access time = 100 ns PFL input Clock = 100 MHz DCLK ratio = 2 • Use the following formulas in this calculation: Tpage_access = 30 ns Caccess = [(Taccess*Fclk+1) + (Tpage_access*Fclk*15)]/16 Cflash for Page Mode = Caccess / 2 Ccfg = 2.5 Coverhead = 3* Caccess Total Clock Cycles = Coverhead + max (Cflash, Ccfg)*N Total Configuration Time = Total Clock Cycle/ PFL Input Clock • Substitute these values in the following formulas: Caccess = [((100ns * 100 MHz) + 1) + (30ns*100 MHz*15)]/16 = 3.5 Cflash for Page Mode = 3.5/ 2 = 1.75 = 2 Ccfg = 2.5 Coverhead = 3*3.5 = 10.5 Total Clock Cycles = 10.5 + 2.5*590848 = 1477130.5 Total Configuration Time at 100 MHz = 1477130.5 / 100 × 106 = 14.77 ms Parallel Flash Loader IP Core User Guide Send Feedback Altera Corporation 54 UG-01082 2015.06.15 Specifications Example 4: Burst Mode • Burst mode configuration time calculation: .rbf size for EP2S15 = 577KB = 590,848 Bytes Configuration mode = FPP without data compression or encryption Flash access mode = Burst Mode Flash data bus width = 16 bits Flash access time = 100 ns PFL input Clock = 100 MHz DCLK ratio = 2 • Use the following formulas in this calculation: Caccess = Taccess*Fclk+1 Cflash for Burst Mode = 1 Ccfg = 2 Coverhead = 20* Caccess + 8 Total Clock Cycles = Coverhead + max (Cflash, Ccfg)*N Total Configuration Time = Total Clock Cycle/ PFL Input Clock • Substitute these values in the following formulas: Caccess = (100ns * 100 MHz) + 1 = 11 Cflash = 1 Ccfg = 2 Coverhead = (20*11)+8 = 228 Total Clock Cycles = 228 + 2 * 590848 = 1181924 Total Configuration Time at 100 MHz = 1181924 / 100 × 106 = 11.82 ms Altera Corporation Parallel Flash Loader IP Core User Guide Send Feedback UG-01082 2015.06.15 Specifications 55 Example 5: Single Quad SPI Flash • Single quad SPI flash configuration time calcualtion .rbf size for EP2S15 = 577KB = 590,848 Bytes Configuration mode = FPP without data compression or encryption Flash access mode = Burst Mode Flash data bus width = 4 bits (only one quad SPI flash is used) Flash access time = 100 ns PFL input Clock = 100 MHz DCLK ratio = 2 • Use the following formulas in this calculation: Cflash = 4 Ccfg = 2 Coverhead = 48 Total Clock Cycles = Coverhead + max (Cflash, Ccfg)*N Total Configuration Time = Total Clock Cycle/ PFL Input Clock • Substitute these values in the following formulas: Cflash = 4 Ccfg = 2 Coverhead = 48 Total Clock Cycles = 48 + 4 * 590848 = 2363440 Total Configuration Time at 100 MHz = 2363440 / 100 × 106 = 23.63 ms Example 6: Four Cascaded Quad SPI Flashes • Four cascaded quad SPI flashes configuration time calcualtion: .rbf size for EP2S15 = 577KB = 590,848 Bytes Configuration mode = FPP without data compression or encryption Flash access mode = Burst Mode Flash data bus width = 16 bits (total bus width for four quad SPI flashes) Flash access time = 100 ns PFL input Clock = 100 MHz DCLK ratio = 2 The configuration time calculation for four cascaded quad SPI flash is identical to the configura‐ tion time calculation for CFI flash with 16 bit flash data width. Parallel Flash Loader IP Core User Guide Send Feedback Altera Corporation 56 UG-01082 2015.06.15 Document Revision History Document Revision History Date Version Changes June 2015 2015.06.15 Added support for Spansion S25FS256S and S25FS512S. January 2015 2015.01.23 • Corrected DATA width in PFL IP core With Dual P30 or P33 CFI Flash Memory Devices figure. • Corrected Spansion part number for S29JL032H and S29JL032H from 229JL032H and 229JL032H respectively. • Added Micron MT28GU512AAA1EGC-0SIT and MT28GU01GAAA1EGC-0SIT • Added example of programming PFL using command line. • Rearranged the supported flash memory device by grouping device families. • Added third-party programmer support. June 2014 2014.06.30 Replaced MegaWizard Plug-In Manager information with IP Catalog. May 2014 3.2 Updated Table 16 on page 41 to remove Stratix V limitation for the Enhanced bitstream decompression IP core option. May 2013 3.1 Updated Table 2 on page 5 to add 28F00BP30 and 28F00BP33. September 2012 3.0 • Updated manufacturer name from Numonyx to Micron. • Updated “Implementing Remote System Upgrade with the PFL IP Core” on page 22, and “Specifications” on page 49 • Updated Table 4 on page 7, Table 10 on page 30, Table 16 on page 41, Table 17 on page 45, and Table 18 on page 50. • Removed figures. August 2012 2.1 Updated Table 1. December 2011 2.0 • Updated “Using Enhanced Bitstream Compression and Decompression” to include reference. • Updated Table 1 to include Eon Silicon CFI device EN29GL128 and to remove S29GL-N devices. • Updated Table 2 to include Micron QSPI device N25Q128. • Updated “Specifications” • Updated Table 13 to include FPP x16 and FPP x32 configuration scheme for Stratix V devices. • Updated Figure 27. • Added Figure 31. • Minor text edits February 2011 1.1 • Restructured the user guide. • Added information about the new feature for the Quartus II software 10.1 release: Support for NAND flash. Altera Corporation Parallel Flash Loader IP Core User Guide Send Feedback UG-01082 2015.06.15 Document Revision History Date July 2010 Version 1.0 Parallel Flash Loader IP Core User Guide Send Feedback 57 Changes Converted from AN386: Using the Parallel Flash Loader With the Quartus II Software. Altera Corporation