ROHM BD5468GUL

Small-sized Class-D Speaker Amplifiers
Analog Input
Monaural Class-D Speaker Amplifier
No.10101EAT08
BD5468GUL
●Description
BD5468GUL is a monaural Class-D speaker amplifier that contained ALC function for mobile phone, portable type
electronic devices etc. LC filter of speaker output is not needed, can form monaural speaker amplifier. with 3 external parts.
ALC, short for Automatic Level Control, is a function that automatically adjusts up to the level of suppression of distortion
(clip) of output wave form during excessive input. The time until the limit release operation of output level is called the
release time (or recovery time). This IC adopts high-speed release time (4ms/1dB Typ.) and suits the application which
repeats big volume in the short time such as the camera shutter sound.
Through Class-D operation, efficiency is high low power consumption that is why it’s suitable for battery drive application.
The current consumption during shutdown when lowered to 0.01μA(Typ.), from the shutdown to the operation time is early
and at the same time pop sound is few that is why its also suitable in repeating active and shutdown.
●Feature
1) Contains Digital ALC (Automatic Level Control) Function
2) External Parts: 3points
3) Ultra slim type package: 9pin WL-CSP(1.7×1.7×0.55mmMax.)
4) BD5460/61GUL (No ALC Function, Gain Fixed Goods) Pin Compatible Specs
BD5465/66/67GUL (ALC Function, Gain Fixed Goods) Pin Compatible Specs
5) Maximum Gain: 13dB (Typ.) [during ALC operation, 13~-2dB@1dB Step]
6) ALC high speed release (recovery) time: 4ms/1dB(Typ.)
7) Limit output power : 0.7W (Typ.) [VDD=4.2V, RL=8Ω, THD+N≦1%]
: 0.5W (Typ.) [VDD=3.6V, RL=8Ω, THD+N≦1%]
8) Audio Analog Input (corresponds to single-end input / differential input)
9) Output LC filter free
10) Pop noise suppression circuit
11) Shutdown Function (use as mute at the same time) [low shutdown current = 0.01μA (Typ.)]
12) Contains protection circuit: output short, thermal shutdown, under voltage lockout (UVLO)
●Applications
Mobile phone, Portable audio device, PND, DSC, Note-PC etc.
●Absolute Maximum Rating (Ta=+25℃)
Parameter
Power Supply Voltage
Power Dissipation
Storage Temperature Range
SDNB Pin Input Range
IN+, IN- Pin Input Range
Symbol
Ratings
Unit
VDDmax
PVDDmax
7.0
V
Pd
690※
mW
Tstg
-55 ~ +150
℃
VSDNB
-0.3~VDD+0.3
V
VIN
-0.3~VDD+0.3
V
※ In case Ta=+25℃ or more, 5.52 mW decrease per 1℃
When mounting Rohm Typical Board 50.0mm×58.0mm (Material :Glass Epoxy)
●Operation Range
Parameter
Temperature
Power Supply Voltage
Common Mode Input Voltage Range
Symbol
Range
Unit
Topr
-40 ~ +85
℃
VDD
PVDD
+2.5 ~ +5.5
V
VIC
+0.5 ~ VDD-0.8
V
◎ This product is not designed for protection against radioactive rays.
www.rohm.com
© 2010 ROHM Co., Ltd. All rights reserved.
1/19
2010.09 - Rev.A
Technical Note
BD5468GUL
●Electrical Characteristic (Ta=+25℃, VDD=+3.6V, Unless specified otherwise)
Parameter
Symbol
Limits
Min.
Typ.
Max.
Unit
Conditions
<All Device>
IC Active, No Load
VSDNB =VDD
IC Shutdown
VSDNB =GND
Circuit current (no signal)
ICC
―
3
6
mA
Circuit current (shutdown)
ISDN
―
0.01
2
μA
PO
0.035
2
×VDD
0.044
2
×VDD
0.055
2
×VDD
W
Total harmonic distortion
THD+N
―
0.2
1
%
Maximum Gain
GMAX
12
13
14
dB
BTL, *1
ALC Limit level
VLIM
1.89
×VDD
1.5
×VDD
BTL, *1
VREL
1.68
×VDD
1.34
×VDD
Vpp
ALC Release level
1.5
×VDD
1.19
×VDD
Vpp
BTL, *1
Switching frequency
fOSC
150
250
350
kHz
Start-up time
TON
0.73
1.02
1.71
msec
Ri
36
55
74
kΩ
Gain=13dB
H
VSDNBH
1.4
―
VDD
V
IC Active
L
VSDNBL
0
―
0.4
V
IC Shutdown
H
ISDBNH
12
24
36
μA
VSDNB =3.6V
L
ISDNBL
-5
―
5
μA
VSDNB =0V
<Audio Feature>
Limit output power
Audio input resistance
BTL, f=1kHz, RL=8Ω
THD+N≦1% , *1
BTL, fin=1kHz, RL=8Ω
PO =0.3W, *1
<Control Terminal>
SDNB terminal
Threshold voltage
SDNB terminal
Inflow Current
*1
Filter bandwidth for measurement :400~30kHz, LC filter for AC measurement :L=22μH / C=1μF, BTL :Voltage between A3,C3
●Shutdown control
Control terminal
Conditions
SDNB
H
IC operation (active)
L
IC stop (shutdown)
●ALC Parameter
ALC Parameter
Attack Time
(Typ.)
~1ms/1dB @ fin=100Hz
~0.5ms/1dB @ fin=1kHz
~0.05ms/1dB @ fin=10kHz
Release Time(Typ.)
Gain Switch Step (Typ.)
4ms/1dB
@ fin=100~10kHz
±1dB
The gain switch timing during ALC operation occurs at zero cross point of audio output voltage.
For that, attack time, release time will change at input frequency “fin”.
ALC Parameter is fixed. ALC operation doesn’t correspond to noise of impulse.
www.rohm.com
© 2010 ROHM Co., Ltd. All rights reserved.
2/19
2010.09 - Rev.A
Technical Note
BD5468GUL
●Measurement Circuit Diagram
<Audio Characteristics Method of Evaluation >
■In case LC filter is not used
+Battery
C3
10uF
VDD
SDNB
Shutdown Signal
B2
Shutdown
Control
C2
150k
(Typ .)
H : IC Active
L : IC Shutdown
B1
PVDD
BIAS
OSC
ALC
0. 1uF
IN +
A1
Ri
OUT +
Rf
C3
C2
PWM
0. 1uF
HBridge
OUT -
IN C1
A3
Ri
C1
Rf
BTL
GND
A2
B3
Measurement Instrument
PGND
LPF
AP AUX-0025
Audio
Precision
(AP)
■In case LC filter is used
+Battery
C3
10uF
VDD
Shutdown Signal
SDNB
B2
Shutdown
Control
C2
150k
(Typ .)
H : IC Active
L : IC Shutdown
B1
PVDD
BIAS
OSC
ALC
0. 1uF
IN +
A1
Ri
22uH
Rf
C3
C2
PWM
0. 1uF
1 uF
HBridge
1uF
IN C1
C1
A3
Ri
Rf
22uH
BTL
GND
A2
B3
PGND
Audio Precision
(AP )
Audio characteristics can be measured to insert LC filter between output pin and speaker load, if you don’t have
measurement equipment for switching amplifier, like AUX-0025, Audio Precision.
Arrange the LC filter directly close to output pin.
In case of L=22μH, C=1μF, cut off frequency becomes:
1
1

 34kHz
2 LC 2 22 H  1F
For Inductor L, please use huge current type.
fc 
www.rohm.com
© 2010 ROHM Co., Ltd. All rights reserved.
(Reference)TDK : SLF12575T-220M4R0
3/19
2010.09 - Rev.A
Technical Note
BD5468GUL
●External Dimension Diagram
Top View
Bottom View
5468
LOT No.
9pin WL-CSP (VCSP50L1)
[ 1.7×1.7×0.55mm Max, 0.5mm Pitch ]
(Unit : mm)
Side View
●Block Diagram
●Pin Arrangement (Bottom View)
VDD B1
SDNB
Shutdown
Control
C2
B2 PVDD
BIAS
150k
(Typ.)
OSC
ALC
IN+
Ri
OUT+
Rf
A1
C3
PWM
HBridge
IN-
OUT-
C1
A3
Ri
Rf
GND A2
●Pin Explanation
Pin No.
Pin Name
C3
IN-
SDNB
OUT+
B1
B2
B3
VDD
PVDD
PGND
A1
A2
A3
IN+
GND
OUT-
Explanation
IN+
A2
GND
A3
OUT-
Class-D BTL output - terminal
B1
VDD
VDD terminal (signal)
B2
PVDD
VDD terminal (power)
Audio differential input+ terminal
GND terminal (signal)
B3
PGND
C1
IN-
C2
SDNB
Shutdown control terminal
C3
OUT+
Class-D BTL output+ terminal
www.rohm.com
C2
B3 PGND
A1
© 2010 ROHM Co., Ltd. All rights reserved.
Index Post
C1
GND terminal (power)
Audio differential input - terminal
4/19
2010.09 - Rev.A
Technical Note
BD5468GUL
●Application circuit example
SHORT the power supply pin VDD (B1), PVDD (B2) at board pattern, then use singleness power supply.
Singleness power supply (+2.5~+5.5V)
+Battery
C3
10 uF
Signal VDD
Shutdown Control
Shutdown Signal
SDNB
B1
B2
Shutdown
Control
C2
150k
(Typ.)
H: IC Active
L: IC Shutdown
VDD
PVDD
Power VDD
BIAS
OSC
Class-D BTL Output
ALC
Audio
Input +
Differential
Input
0 .1 uF
IN+
A1
Ri
OUT +
Rf
C3
PWM
Audio
Input -
0 .1 uF
HBridge
IN-
OUT -
C1
A3
Rf
Ri
Signal GND
Audio Differential Input
GND
A2
B3
PGND
Power GND
Fig1. Differential Input (With Input Coupling Capacitor)
+Battery
Singleness power supply(+2.5~+5.5V)
C3
10 uF
Signal VDD
Shutdown Control
Shutdown Signal
SDNB
B1
B2
Shutdown
Control
C2
150k
(Typ.)
H: IC Active
L: IC Shutdown
VDD
PVDD
Power VDD
BIAS
OSC
Class-D BTL Output
ALC
IN+
Audio
Input +
Differential
Input
A1
Ri
OUT +
Rf
C3
PWM
Audio
Input -
HBridge
IN-
OUT -
C1
A3
Audio Differential Input
Ri
Rf
Signal GND
GND
A2
B3
PGND
Power GND
Fig2. Differential Input (Without Input Coupling Capacitor)
www.rohm.com
© 2010 ROHM Co., Ltd. All rights reserved.
5/19
2010.09 - Rev.A
Technical Note
BD5468GUL
Singleness power supply (+2.5~+5.5V)
+Battery
C3
10uF
Signal VDD
VDD
Shutdown Control
Shutdown Signal
SDNB
B2
Shutdown
Control
C2
150k
(Typ.)
H: IC Active
L: IC Shutdown
B1
PVDD
Power VDD
BIAS
OSC
Class-D BTL Output
Audio Single End Input
Audio
0. 1uF
ALC
IN +
A1
Input
Ri
OUT +
Rf
C3
PWM
0. 1uF
H Bridge
IN -
OUT -
C1
A3
Ri
Rf
Signal GND
GND
A2
B3
PGND
Power GND
Fig3. Single end input (during IN+ input)
Singleness power supply (+2.5~+5.5V)
+Battery
C3
10uF
Signal VDD
Shutdown Control
Shutdown Signal
SDNB
B1
B2
Shutdown
Control
C2
150k
(Typ.)
H: IC Active
L: IC Shutdown
VDD
PVDD
Power VDD
BIAS
OSC
Class-D BTL Output
ALC
0. 1uF
IN +
A1
Ri
OUT +
Rf
C3
PWM
Audio
0. 1uF
Input
HBridge
IN -
OUT -
C1
Audio Single End Input
A3
Ri
Rf
Signal GND
GND
A2
B3
PGND
Power GND
Fig4. Single end input (during IN- Input)
www.rohm.com
© 2010 ROHM Co., Ltd. All rights reserved.
6/19
2010.09 - Rev.A
Technical Note
BD5468GUL
●About the difference of differential input and single end input
・BD5468GUL uses full differential amplifier.
BD5468GUL is a Class-D but, in relation to Audio Input and Output, is same with the conventional Class-AB Amplifier.
For simplicity purposes of the diagram, the Class-D amplifier output stage is omitted in the following explanation.
About the resistor, signal
on the diagram
Gives meaning to changes of gain setting by means of ALC Control.
1) Differential Input
Opposite
phase
Audio
Input
0V
IN+
A1
OUTA3
(IN+ - IN- )
Audio
Input
(OUT+ - OUT- )
0V
C1
C3
IN-
OUT+
Opposite
phase
2) Single end input (during IN+input )
Audio
Input
0V
Opposite
phase
IN+
OUT-
A1
A3
Same p
hase
(IN+ - IN- )
0V
ー
(OUT+ - OUT- )
C1
C3
IN-
ー
OUT+
IN+
ー
OUT-
3) Single end input (during IN-input )
0V
ー
A1
A3
(IN+ - IN- )
e
e phas
Opposit
(OUT+ - OUT- )
0V
Audio
Input
C1
C3
INOpposite
phase
OUT+
○About single end input
・Input is possible whether IN+ or IN- Pin.
Don’t make input pin open, through the input coupling capacitor, please connect to GND as seen on the example above.
Audio input pin should make “mute” condition, not “open” condition when you don’t input any signal.
・During single end input IN+ and IN-, there is a difference with the phase relation of input and output.
Because of differential amplifier, if input (IN+ - IN-), output(OUT+ - OUT-), the audio input and output phase relation will
become:
Phase
IN+ Input
IN- Input
Audio Input ⇒ output (OUT+ - OUT-)
Same phase
Opposite phase
www.rohm.com
© 2010 ROHM Co., Ltd. All rights reserved.
7/19
2010.09 - Rev.A
Technical Note
BD5468GUL
○Gain calculation
【Differential Input】
【single end input】
+Battery
+Battery
Cs
Cs
VDD
Shutdown Signal
SDNB
B2 PVDD
150k
(Typ.)
VDD
Shutdown Signal
Shutdown
Control
C2
H: IC Active
L: IC Shutdown
B1
SDNB
BIAS
Shutdown
Control
C2
150k
(Typ.)
H: IC Active
L: IC Shutdown
B1
ALC
ALC
IN+
Vins
Vins
A1
Ci
Ri
A1
C3
HBridge
PWM
INC1
Vins
Ci
OUT+
Rf
C3
PWM
IN-
HBridge
C1
Rf
Ci
GND A2
Ri
VIN
(=Vins)
0.1uF
OUTA3
Ri
Ci
IN+
< Audio Source > 0.1uF
OUT+
Rf
VIN
(=2Vins)
0.1uF
BIAS
OSC
OSC
< Audio Source > 0.1uF
B2 PVDD
OUTA3
Ri
Rf
GND A2
B 3 PGND
B 3 PGND
When Input Level is calculated at IC typical and audio source typical, when input coupling capacitor (Ci) value is large
enough,every gain during the differential input and single end input will become:
Typical Input Level
Differential Output
IC
Audio Source
Single End Output
Formula①
Formula②
Formula①
1. IC reference(Difference Input, Single End Input) :Formula ①
VIN means the Input Voltage between IC Input Pin (IN+, IN-), VOUT means the output voltage between IC Output Pin
( OUT+, OUT- ). During differential input and single end input, the gain calculation formula at IC reference which
includes ALC operation is written below:
Gain = 20×log | VOUT/VIN | =+13~-2 (Typ.) [dB] ・・・ Formula①
2. Audio Source reference(Differential Input) : Formula ②
When the input level of audio source is Vins, the relation with the input voltage VIN between IC input pin is written
below:
Vins = VIN / 2
During differential input, at audio source referece that includes ALC operation, gain calculation formula will become :
Gain = 20×log | VOUT / Vins | = 20×log | 2×VOUT / VIN | = +19~+4 (Typ.) [dB] ・・・Formula②
3. Audio Source reference (Single End Input) :Formula ①
When the Input level of audio source is Vins, the relation with input voltage VIN between IC input pin (IN+,IN-)
becomes:
Vins = VIN
During single end input, at the audio source that includes ALC operation, gain calculation formula becomes:
Gain = 20×log | VOUT / Vins | = 20×log | VOUT / VIN | = +13~-2 (Typ.) [dB] ・・・ Formula①
www.rohm.com
© 2010 ROHM Co., Ltd. All rights reserved.
8/19
2010.09 - Rev.A
Technical Note
BD5468GUL
●Audio Input Pin External LPF connection example
■External LPF connection example
st
The connection example of 1 -order LPF which is formed at Resistor RLPF and Capacitor CLPF , to the Audio Input Pin
IN+/- (A1, C1 Pin) is shown below. The cut frequency of input LPF, together with the single end input and differential input
is written below:
fcLPF = 1 / (2×π×RLPF×CLPF) [Hz]
Ex)
fcLPF=10kHz ⇒ CLPF =0.01μF, RLPF=1.59kΩ
1) During single end input
When LPF is connected to audio input pin at single end input setting, at start-up characteristics of audio input pin IN+/-,
during start-up with unbalance (power supply ON/OFF, or shutdown ON/OFF), there is a risk that POP sound will occur
so please be careful.
When no audio input, and in order to prevent output noise, please make previous IC “mute” condition, not “open”
condition. Please refer at the same time to POP Sound countermeasure example.
+Battery
Cs
VDD B1 B2 PVDD
Shutdown Signal
H: IC Active
L :IC Shutdown
SDNB
Shutdown
Control
C2
BIAS
150k
(Typ .)
ALC
Input Impedance
OSC
Front IC
Ro
RLPF
IN+
A1
Ci
Ri
C3
CLPF
RLPF
Pop sound
→
countermeasure
Ci
OUT+
Rf
PWM
IN-
HBridge
C1
CLPF
Ri
Rf
Speaker
A3
OUT-
GND A2 B3 PGND
www.rohm.com
© 2010 ROHM Co., Ltd. All rights reserved.
9/19
2010.09 - Rev.A
Technical Note
BD5468GUL
2) Differential Input
+Battery
Cs
VDD B1 B2 PVDD
Shutdown Signal
SDNB
H: IC Active
L: IC Shutdown
Shutdown
Control
C2
BIAS
150k
(Typ.)
ALC
Input Impedance
Front IC
Ro
OSC
LPF
Ci
RLPF
IN+
Ri
OUT+
Rf
A1
C3
CLPF
Ro
PWM
Ci
RLPF
INC1
CLPF
Ri
HBridge
A3
Rf
GND A2 B3
Speaker
PGND
OUT-
■Caution during External LPF Setting
External LPF Resistor RLPF which is composed of IC input resistor Ri, forms input impedance.
The bigger the resistor value of LPF resistor RLPF, the more it will decrease the gain.
When the input capacitor Ci has enough large capacity value, the relation among external LPF resistor RLPF and IC input
resistor Ri and Gain will become:
Gain = 20×log | Rf / (Ri + RLPF ) | [dB]
Input resistor Ri of BD5468GUL and resistor value of feedback resistor Rf will become the following below,
during ALC operation, changes at ±1dB step, and becomes 16 stages switch specs.
#1. Ri=55kΩ(Typ.), Rf=245kΩ(Typ.) @Gain=13dB
#2. Ri=60kΩ(Typ.), Rf=240kΩ(Typ.) @Gain=12dB
#3. Ri=66kΩ(Typ.), Rf=234kΩ(Typ.) @Gain=11dB
↓
#15. Ri=159kΩ(Typ.), Rf=141kΩ(Typ.) @Gain=-1dB
#16. Ri=167kΩ(Typ.), Rf=132kΩ(Typ.) @Gain=-2dB
Also with the driver ability of previous IC step, after checking, constant setting of external LPF and Resistor RLPF.
www.rohm.com
© 2010 ROHM Co., Ltd. All rights reserved.
10/19
2010.09 - Rev.A
Technical Note
BD5468GUL
●Evaluation Board Circuit Diagram
Connect to GND
Connect to Power Supply
(VDD=+2.5~5.5V)
VDD
C3
10uF
VDD
VDD B1
SDNB
Shutdown Signal
Shutdown
Control
C2
H: IC Active
B2
PVDD
BIAS
150k
(Typ.)
L: IC Shutdown
OSC
Audio Input
Audio
Input+
ALC
0.1uF
IN+
A1
Differential
Input
Ri
OUT+
Rf
C3
C2
Audio
Input-
PWM
0.1uF
HBridge
OUT-
INC1
C1
Ri
BD5468GUL
A3
Rf
GND A2
GND
Connect to input signal
B3 PGND
Connect to Speaker
※Power Supply terminals VDD(B1), PVDD(B2) are SHORT in the board pattern and use a single power.
●Evaluation Board Parts List
Qty.
Item
Description
SMD Size
Manufacturer/
Part Number
2
C1, C2
Capacitor, 0.1μF
0603
Murata
GRM188R71C104KA01D
1
C3
Capacitor, 10μF
A (3216)
ROHM
TCFGA1A106M8R
1
S1
Slide Switch
4mm X 10.2mm
NKK
SS-12SDP2
1
U1
IC, BD5468GUL,
Mono Class-D Audio Amplifier
1.7mm X 1.7mm
WLCSP Package
ROHM
BD5468GUL
1
PCB1
Printed-Circuit Board,
BD5468GUL EVM
―
―
●About the external part
① Input coupling capacitor (C1, C2)
Input coupling capacitor is 0.1μF.
Input impedance during maximum gain 13dB is 55kΩ (Typ.). A high-pass filter is composed by the input coupling
capacitor and the input impedance.
Cut-off frequency”fc” by the formula below, through input coupling capacitor C1(=C2) and input impedance Ri.
1
fc 
ٛٛٛٛ
2  Ri  C1
In case of Ri=55kΩ, C1(=C2)=0.1μF, cut-off frequency is about 29Hz
② Power Supply Decoupling Capacitor (C3)
Power Supply Decoupling Capacitor is 10uF. When the capacity value of Power Supply Decoupling Capacitor is made
small, it will have an influence to the audio characteristics. When making it small, be careful with the audio characteristics
at actual application. ESR (equivalent series resistor) is low enough; please use capacitor with capacity value of 1μF or
more.
www.rohm.com
© 2010 ROHM Co., Ltd. All rights reserved.
11/19
2010.09 - Rev.A
Technical Note
BD5468GUL
●Evaluation Board PCB Layer
TOP Layer Silk Pattern
BD5468GUL
TOP Layer
Bottom Layer
www.rohm.com
© 2010 ROHM Co., Ltd. All rights reserved.
12/19
2010.09 - Rev.A
Technical Note
BD5468GUL
●About IC Thermal Design
The IC Characteristics has a big relation with the temperature that will be used, to exceed the maximum tolerance junction
temperature, can deteriorate and destroy it. Instant destruction and long-time operation, from these 2 standpoints, there is a
need to be careful with regards to IC thermal. Please be careful with the next points.
The absolute maximum rating of IC shows the maximum junction temperature (TjMAX.) or the operation temperature range
(Topr), so refer to this value, use Pd-Ta characteristics (Thermal reduction ratio curve). If input signal is excessive at a state
where heat radiation is not sufficient, there will be TSD(Thermal Shutdown)
For TSD, the chip temperature operates at around 180℃, releases if its around 120℃ or less. Since the aim is to prevent
damage on the chip, please be careful because the long use time at the vicinity where TSD operates can deteriorate the
dependency of the IC.
Thermal Reduction Ratio Curve
Reference Data
VCSP50L1
2.0
Measurement Condition: ROHM Typical Board Mount
Board Size: 50mmx58mm
Power Dissipation Pd(W)
1.5
1.0
0.69W
θja =
0.5
0.0
0
25
50
75
85
181.8℃/W
100
125
150
Perimeter Temperature Ta(℃)
Note : This value is the real measurement, but not the guaranteed value.
The value of power dissipation changes based on the board that will be mounted.
The power dissipation of main IC during the heat dissipation design of many mounted boards, will become bigger than the
value of the above graph.
www.rohm.com
© 2010 ROHM Co., Ltd. All rights reserved.
13/19
2010.09 - Rev.A
Technical Note
BD5468GUL
Evaluation data - Typical Characteristics (1/4)
●Evaluation data – Typical characteristics (1/4)
Efficiency - Output power
f=1kHz, RL=8Ω+33uH
90
80
70
VDD = 5.0V
VDD = 3.6V
VDD = 3.6V
70
60
VDD = 2.5V
50
40
30
VDD=2.5V
VDD=3.6V
VDD=5.0V
20
10
0.1
0.2
0.3
0.4
0.5 0.6 0.7 0.8
Output Power [W]
0.9
1
50
40
30
VDD=2.5V
VDD=3.6V
VDD=5.0V
20
10
0
0
1.1
0
1.2
0
0.2
0.4
0.6
0.8
1
1.2
Output Power [W]
Fig.5
Figure.1
1.4
1.6
1.8
2
Fig.6
Figure.2
Supply Current vs Output power
f=1kHz, RL=8Ω+33uH
300
VDD = 5.0V
VDD = 2.5V
60
Efficiency [%]
Efficiency [%]
Efficiency vs Output power
f=1kHz, RL=4Ω+33uH
80
Supply Current vs Output power
f=1kHz, RL=4Ω+33uH
450
400
250
350
VDD = 5.0V
VDD = 3.6V
Icc [mA]
Icc [mA]
VDD = 5.0V
300
200
150
VDD = 2.5V
50
250
VDD = 2.5V
200
150
VDD=2.5V
VDD=3.6V
VDD=5.0V
100
VDD = 3.6V
VDD=2.5V
VDD=3.6V
VDD=5.0V
100
50
0
0
0
0.1
0.2
0.3
0.4 0.5 0.6 0.7
Output Power [W]
0.8
0.9
1
1.1
0
1.2
0.2
0.4
0.6
0.8
1
1.2 1.4
Output Power [W]
Fig.7
Figure.3
1.8
2
Fig.8
Figure.4
Power dissipation vs Output power
f=1kHz, RL=4Ω+33uH
Power dissipation vs Output power
f=1kHz, RL=8Ω+33uH
0.3
1.6
0.45
0.40
0.25
VDD = 5.0V
0.35
0.30
VDD = 5.0V
0.15
Pd [W]
Pd [W]
0.2
VDD = 3.6V
VDD = 3.6V
0.25
0.20
VDD = 2.5V
0.1
0.05
VDD=2.5V
VDD=3.6V
VDD=5.0V
0.15
VDD=2.5V
VDD=3.6V
VDD=5.0V
VDD = 2.5V
0.10
0.05
0
0.00
0
0.1
0.2
0.3
0.4
0.5 0.6 0.7 0.8
Output Power [W]
0.9
1
1.1
1.2
0
0.2
0.4
0.6
1.4
1.6
1.8
2
Fig.10
Figure.6
Figure.5
Fig.9
Supply Current vs Power Supply
RL=No load, No signal
5.0
5.0
4.5
4.5
4.0
4.0
3.5
3.5
3.0
3.0
ISDN [μA]
ICC [mA]
0.8
1
1.2
Output Power [W]
2.5
2.0
2.5
2.0
1.5
1.5
1.0
1.0
0.5
0.5
0.0
Shutdown Current vs Power Supply
RL=No load, No signal
0.0
0
1
2
3
VDD [V]
4
5
6
0
www.rohm.com
2
3
VDD [V]
4
5
6
Fig.12
Figure.8
Fig.11
Figure.7
© 2010 ROHM Co., Ltd. All rights reserved.
1
14/19
2010.09 - Rev.A
Technical Note
BD5468GUL
Evaluation data - Typical Characteristics (2/4)
●Evaluation data – Typical characteristics (2/4)
Output power vs Load Resistance
THD+N=1%, f=1kHz, 400Hz-30kHz BPF
2.0
VDD=2.5V
VDD=3.6V
VDD=5.0V
1.8
Output Power [W]
1.6
1.4
VDD = 5.0V
1.2
1.0
0.8
0.6
VDD = 3.6V
VDD = 2.5V
0.4
0.2
0.0
4
8
12
16
20
RL[Ω]
24
28
32
Fig.13
Figure.9
Output Power vs Power Supply
RL=4Ω, f=1kHz, 400Hz-30kHz BPF
1.2
2.5
1.0
2.0
Output Power [W]
Output Power [W]
Output Power vs Power Supply
RL=8Ω, f=1kHz, 400Hz-30kHz BPF
0.8
0.6
0.4
1.5
1.0
THD+N≦1%
THD+N≦1%
0.2
0.5
0.0
2
2.5
3
3.5
4
VDD[V]
4.5
5
5.5
0.0
6
2
2.5
3
3.5
Fig.14
Figure.10
100
4
VDD[V]
4.5
5
5.5
6
Fig.15
Figure.11
Total Harmonic Distortion + Noise vs Output Power
RL=4Ω, f=1kHz, 400Hz-30kHz BPF
Total Harmonic Distortion + Noise vs Output Power
RL=8Ω, f=1kHz, 400Hz-30kHz BPF
100
VDD = 2.5V
VDD = 3.6V
VDD = 5.0V
VDD = 2.5V
VDD = 3.6V
VDD = 5.0V
VDD = 3.6V
VDD = 3.6V
VDD = 2.5V
10
VDD = 2.5V
THD+N [%]
THD+N [%]
10
VDD = 5.0V
1
VDD = 5.0V
1
0.1
0.01
0.1
1
10
0.1
0.01
0.1
Output Power [W]
Fig.16
Figure.12
1
10
Fig.17
Figure.13
Total Harmonic Distortion + Noise vs Frequency
VDD=3.6V RL=8Ω, 400Hz-30kHzBPF
Total Harmonic Distortion + Noise vs Frequency
VDD=5.0V RL=8Ω, 400Hz-30kHz BPF
10
Output Power [W]
10
Po=25mW
Po=100mW
Po=250mW
Po=25mW
Po=100mW
Po=250mW
Po = 100mW
1
Po = 100mW
THD+N [%]
THD+N [%]
1
Po = 25mW
Po = 250mW
0.1
Po = 25mW
Po = 250mW
0.1
0.01
0.01
10
100
1k
Frequency [Hz]
10k
100k
Fig.18
Figure.14
www.rohm.com
© 2010 ROHM Co., Ltd. All rights reserved.
10
100
1k
Frequency [Hz]
10k
100k
Fig.19
Figure.15
15/19
2010.09 - Rev.A
Technical Note
BD5468GUL
Evaluation
- Typical
Characteristics
(3/4)
●Evaluation
data –data
Typical
characteristics
(3/4)
Total Harmonic Distortion + Noise vs Frequency
VDD=2.5V, RL=8Ω, 400Hz-30kHz BPF
Total Harmonic Distortion + Noise vs Frequency
RL=8Ω, Po=125mW, 400Hz-30kHz BPF
10
10
Po=25mW
Po=100mW
Po=150mW
Po = 100mW
1
THD+N [%]
1
THD+N [%]
VDD=2.5V
VDD=3.6V
VDD=5.0V
Po = 25mW
Po = 150mW
0.1
VDD = 3.6V
0.1
VDD = 5.0V
VDD = 2.5V
0.01
0.01
10
100
1k
Frequency [Hz]
10k
10
100k
100
1k
Frequency [Hz]
Fig.20
Figure.16
10
10
Gain [dB]
12
Gain [dB]
12
8
6
VDD = 3.6V
VDD=2.5V
VDD=3.6V
VDD=5.0V
2
Gain_vs_Frequency
RL=4Ω, Vin=0.5Vpp, 400Hz-30kHz BPF
14
VDD = 5.0V
4
100k
Fig.21
Figure.17
Gain vs Frequency
RL=8Ω, Vin=0.5Vpp, 400Hz-30kHz BPF
14
10k
VDD = 5.0V
8
6
4
VDD=2.5V
VDD=3.6V
VDD=5.0V
2
VDD = 2.5V
0
VDD = 3.6V
VDD = 2.5V
0
10
100
1k
Frequency [Hz]
10k
100k
10
100
1k
Frequency [Hz]
Fig.22
Figure.18
10k
100k
Fig.23
Figure.19
Output Power vs Input Level @ sweep up
RL=8Ω, f=1kHz, 400Hz-30kHz BPF
Output Power vs Input Level @ sweep up
RL=4Ω,f=1kHz, 400Hz-30kHz BPF
10
10
VDD = 5.0V
VDD = 5.0V
1
Output Power [W]
Output Power [W]
1
VDD = 3.6V
100m
VDD = 2.5V
10m
VDD = 2.5V
VDD = 3.6V
VDD = 5.0V
1m
-30
-25
-20
-15
-10
Vin [dBV]
-5
0
VDD = 3.6V
100m
10m
1m
-30
5
VDD = 2.5V
VDD = 2.5V
VDD = 3.6V
VDD = 5.0V
-25
-20
-15
Fig.24
Figure.20
-10
-5
Vin [dBV]
0
5
10
15
Fig.25
Figure.21
Total Harmonic Distortion + Noise vs Input Level @ sweep up
RL=8Ω,f=1kHz, 400Hz-30kHz BPF
Total Harmonic Distortion + Noise vs Input Level @ sweep up
RL=4Ω,f=1kHz, 400Hz-30kHz BPF
100
100
VDD = 2.5V
VDD = 3.6V
VDD = 5.0V
VDD = 2.5V
VDD = 3.6V
VDD = 5.0V
VDD = 3.6V
VDD = 2.5V
1
10
VDD = 2.5V
THD+N [%]
THD+N [%]
10
1
VDD = 3.6V
VDD = 5.0V
VDD = 5.0V
0.1
-30
-25
-20
-15
-10
Vin [dBV]
-5
0
0.1
-30
5
Fig.26
Figure.22
www.rohm.com
© 2010 ROHM Co., Ltd. All rights reserved.
-25
-20
-15
-10
-5
Vin [dBV]
0
5
10
15
Fig.27
Figure.23
16/19
2010.09 - Rev.A
Technical Note
BD5468GUL
●Evaluation
data – Typical
(4/4)
(4/4)
Evaluation
data -characteristics
Typical Characteristics
ALC Limit Operation Waveform
f=1kHz
ALC Release Operation Waveform
f=1kHz
2V / Div.
2V / Div.
INPUT
INPUT
OUTPUT
-1
OUTPUT
0
1
2
3
4
Time [msec]
5
6
-10
7
0
10
20
Fig.28
Figure.24
30
40
Time [msec]
50
60
70
1
1.2
1.4
Fig.29
Figure.25
Waveform during Start-up
Waveform during Shutdown
1V / Div.
1V / Div.
INPUT
INPUT
OUTPUT
Ton ( Wake-up Time)
OUTPUT
-0.2
0
0.2
0.4
0.6
0.8
Time [msec]
1
1.2
-0.2
1.4
Figure.26
Fig.30
www.rohm.com
© 2010 ROHM Co., Ltd. All rights reserved.
0
0.2
0.4
0.6
0.8
Time [msec]
Figure.27
Fig.31
17/19
2010.09 - Rev.A
Technical Note
BD5468GUL
●Notes for use
(1) The numerical value and the data of the mention are a design representative value and are not the one which guarantees
the value.
(2) It is convinced that it should recommend application circuit example but in case of use, we request the confirmation of the
characteristic more sufficiently. When changing an external part fixed number and becoming use, it considers sprawl of
the external part and our company's LSI including the transition characteristic in addition to the stillness characteristic and
so on, see and fix an enough margin.
(3) Absolute maximum ratings
This IC may be damaged if the absolute maximum ratings for the applied voltage, temperature range, or other
parameters are exceeded. Therefore, avoid using a voltage or temperature that exceeds the absolute maximum ratings.
If it is possible that absolute maximum ratings will be exceeded, use fuses or other physical safety measures and
determine ways to avoid exceeding the IC's absolute maximum ratings.
(4) GND terminal’s potential
Try to set the minimum voltage for GND terminal’s potential, regardless of the operation mode.
(5) Shorting between pins and mounting errors
When mounting the IC chip on a board, be very careful to set the chip's orientation and position precisely. When the
power is turned on, the IC may be damaged if it is not mounted correctly. The IC may also be damaged if a short occurs
(due to a foreign object, etc.) between two pins, between a pin and the power supply, or between a pin and the GND.
(6) Operation in strong magnetic fields
Note with caution that operation faults may occur when this IC operates in a strong magnetic field.
(7) Thermal design
Ensure sufficient margins to the thermal design by taking in to account the allowable power dissipation during actual use
modes, because this IC is power amplifier. When excessive signal inputs which the heat dissipation is insufficient
condition, it is possible that thermal shutdown circuit is active.
(8) Thermal shutdown circuit
This product is provided with a built-in thermal shutdown circuit. When the thermal shutdown circuit operates, the output
transistors are placed under open status. The thermal shutdown circuit is primarily intended to shut down the IC avoiding
thermal runaway under abnormal conditions with a chip temperature exceeding Tjmax=+150℃, and is not intended to
protect and secure an electrical appliance.
(9) Load of the output terminal
This IC corresponds to dynamic speaker load, and doesn't correspond to the load except for dynamic speakers. When
using speaker load 8Ω or less (especially 4Ω), there will be a risk of generating distortion at the speaker output wave form
during ALC limit operation.
(10) The short protection of the output terminal
This IC is built in the short protection for a protection of output transistors. When the short protection is operated, output
terminal become Hi-Z condition and is stopped with latch. Once output is stopped with latch, output does not recover
automatically by canceling the short-circuiting condition. The condition of stopping with latch is cancelled, when power
supply or mute signal is turned off and turned on again.
(11) Operation Range
The rated operating power supply voltage range (VDD=+2.5V~+5.5V) and the rated operating temperature range
(Ta=-40℃~+85℃) are the range by which basic circuit functions is operated. Characteristics and rated output power are
not guaranteed in all power supply voltage ranges or temperature ranges.
(12) Electrical Characteristics
Every audio characteristics list of the limit output power, total harmonic distortion, maximum gain, ALC limit level, ALC
release level etc. shows the typical characteristics of the device, highly dependent to the board lay-out, parts to be used,
power supply. The value when the device and each component are directly mounted to the board of Rohm.
(13) Power Supply
Since the Power Supply Pin for signal (VDD) and power supply for Power (PVDD) is SHORT at internal, short the board
pattern, then use a single power supply. Also, the power supply line of class-D speaker amplifier flows big peak energy. It
will influence the audio characteristics based on the capacity value of power supply decoupling capacitor, arrangement.
For the power supply decoupling capacitor, please arrange appropriately the low capacity (1μF or more) of ESR
(equivalent series resistor) directly near to IC Pin.
(14) ALC (Automatic Level Control) Function
The ALC automatically adjusts the audio output level, and a function that prevents the over output to the speaker. When
ALC function is working, gain switches at zero-cross point of audio output normally. If the time that audio output reaches
to zero-cross point is long, gain switches at about 1msec later (attack time), at about 25msec later (release time). So,
attack time and release time will change at audio input frequency. ALC parameter is fixed. The system does not
correspond to noise of impulse.Also, ALC limit control will become a power supply tracking type, limit output power is
dependent to power supply voltage. The ALC characteristics of limit output power, ALC limit and release limit will be
influenced by the shaking so please be careful.
www.rohm.com
© 2010 ROHM Co., Ltd. All rights reserved.
18/19
2010.09 - Rev.A
Technical Note
BD5468GUL
●Ordering part number
B
D
5
Part No.
4
6
8
Part No.
G
U
L
-
Package
GUL :VCSP50L1
E
2
Packaging and forming specification
E2: Embossed tape and reel
VCSP50L1(BD5468GUL)
<Tape and Reel information>
1.70±0.05
Tape
Embossed carrier tape
Quantity
3000pcs
Direction
of feed
0.55MAX
0.1±0.05
1.70±0.05
1PIN MARK
E2
The direction is the 1pin of product is at the upper left when you hold
( reel on the left hand and you pull out the tape on the right hand
)
(φ0.15)INDEX POST
A
C
B
B
A
1
0.35±0.05
2
P=0.5×2
0.06 S
9-φ0.25±0.05
0.05 A B
0.35±0.05
S
3
1pin
P=0.5×2
(Unit : mm)
www.rohm.com
© 2010 ROHM Co., Ltd. All rights reserved.
Reel
19/19
Direction of feed
∗ Order quantity needs to be multiple of the minimum quantity.
2010.09 - Rev.A
Notice
Notes
No copying or reproduction of this document, in part or in whole, is permitted without the
consent of ROHM Co.,Ltd.
The content specified herein is subject to change for improvement without notice.
The content specified herein is for the purpose of introducing ROHM's products (hereinafter
"Products"). If you wish to use any such Product, please be sure to refer to the specifications,
which can be obtained from ROHM upon request.
Examples of application circuits, circuit constants and any other information contained herein
illustrate the standard usage and operations of the Products. The peripheral conditions must
be taken into account when designing circuits for mass production.
Great care was taken in ensuring the accuracy of the information specified in this document.
However, should you incur any damage arising from any inaccuracy or misprint of such
information, ROHM shall bear no responsibility for such damage.
The technical information specified herein is intended only to show the typical functions of and
examples of application circuits for the Products. ROHM does not grant you, explicitly or
implicitly, any license to use or exercise intellectual property or other rights held by ROHM and
other parties. ROHM shall bear no responsibility whatsoever for any dispute arising from the
use of such technical information.
The Products specified in this document are intended to be used with general-use electronic
equipment or devices (such as audio visual equipment, office-automation equipment, communication devices, electronic appliances and amusement devices).
The Products specified in this document are not designed to be radiation tolerant.
While ROHM always makes efforts to enhance the quality and reliability of its Products, a
Product may fail or malfunction for a variety of reasons.
Please be sure to implement in your equipment using the Products safety measures to guard
against the possibility of physical injury, fire or any other damage caused in the event of the
failure of any Product, such as derating, redundancy, fire control and fail-safe designs. ROHM
shall bear no responsibility whatsoever for your use of any Product outside of the prescribed
scope or not in accordance with the instruction manual.
The Products are not designed or manufactured to be used with any equipment, device or
system which requires an extremely high level of reliability the failure or malfunction of which
may result in a direct threat to human life or create a risk of human injury (such as a medical
instrument, transportation equipment, aerospace machinery, nuclear-reactor controller, fuelcontroller or other safety device). ROHM shall bear no responsibility in any way for use of any
of the Products for the above special purposes. If a Product is intended to be used for any
such special purpose, please contact a ROHM sales representative before purchasing.
If you intend to export or ship overseas any Product or technology specified herein that may
be controlled under the Foreign Exchange and the Foreign Trade Law, you will be required to
obtain a license or permit under the Law.
Thank you for your accessing to ROHM product informations.
More detail product informations and catalogs are available, please contact us.
ROHM Customer Support System
http://www.rohm.com/contact/
www.rohm.com
© 2010 ROHM Co., Ltd. All rights reserved.
R1010A