Small-sized Class-D Speaker Amplifiers Analog Input Monaural Class-D Speaker Amplifiers BD5632NUX,BD5634NUX,BD5638NUX No.10101EAT04 ●Description BD5632NUX, BD5634NUX and BD5638NUX are a low voltage drive class-D speaker amplifier that was developed for mobile phones, mobile audio products and the others. BD5632NUX has a fixed gain of 6dB, BD5634NUX has a fixed gain of 12dB, and BD5638NUX has a fixed gain of 18dB. It is suitable for the application of battery drive because of high efficiency and low power consumption. Also, stand-by current is 0µA (typ.), and fast transitions from standby to active with little pop noise. It is suitable for applications that switch repeatedly between stand-by and active. ●Features 1) LC Filter less 2) Only 3 external components 3) High power 2.5W/4ohm/BTL (VDD=5V, RL=4ohm, THD+N=10%, typ.) 4) High power 0.85W/8ohm/BTL (VDD=3.6V, RL=8ohm, THD+N=10%, typ.) 5) Analog differential input / PWM digital output 6) Pop noise suppression circuit 7) Standby function (Mute function) 8) Protection circuit (Short protection [Auto recover without power cycling], Thermal shutdown, under voltage lockout) 9) Ultra small package VSON008X2030 (2.0×3.0×0.6mmMAX) ●Applications Mobile phones, PND (Personal Navigation Device), DSC, PDA, etc ●Line up matrix Production Name BD5632NUX BD5634NUX BD5638NUX 6 12 18 100 50 25 Gain (dB) Input Impedance (kΩ) Package VSON008X2030 ●Absolute maximum ratings (Ta=25℃) Parameter Power Supply Voltage Power Dissipation Symbol Ratings Unit VDD 7.0 V Pd 0.52 *1 W Storage Temperature Range Tstg -55 ~ +150 ℃ STBY Terminal Input Range Vstby -0.3 ~ VDD+0.3 V Vin -0.3 ~ VDD+0.3 V IN+, IN- Terminal Input Range (*1) ROHM standard board mounted (Board size 70mm×70mm×1.6mmt, 1layer), de-rate the value 4.16mW/deg above Ta=+25deg. ●Operating conditions Parameter Symbol Ratings Unit Power Supply Voltage VDD +2.5 ~ +5.5 V Temperature Range Topr -40 ~ +85 ℃ *This product is not designed for protection against radioactive rays. www.rohm.com © 2010 ROHM Co., Ltd. All rights reserved. 1/14 2010.06 - Rev.A Technical Note BD5632NUX, BD5634NUX, BD5638NUX ●Electric characteristics (Unless otherwise specified, Ta=+25deg, VDD=+3.6V, f=1 kHz, RL=8Ω, AC item=LC Filter; L=22µH, C=1µF) Limits Parameter Symbol Unit Conditions MIN. TYP. MAX. Circuit current (No signal) ICC ― 2.7 5.4 mA Active mode, No load Circuit current (Standby) ISTBY ― 0.1 2 µA Standby mode Output power1 PO1 450 680 ― mW BTL, f=1kHz, THD+N=1% *1 Output power2 PO2 550 850 ― mW BTL, f=1kHz, THD+N=10% *1 5.5 6.0 6.5 11.5 12.0 12.5 dB BTL 17.0 18.0 19.0 Voltage gain (BD5632NUX) Voltage gain (BD5634NUX) GV Voltage gain (BD5638NUX) Switching Frequency fosc 150 250 350 kHz Start-up time Ton 0.36 0.51 0.85 msec STBY threshold voltage VSTBY 0.4 ― 1.4 V Input impedance (STBY) RSTBY 210 300 390 kohm 70 100 130 35 50 65 17.5 25 32.5 Input impedance (IN+/-) (BD5632NUX) Input impedance (IN+/-) (BD5634NUX) Input impedance (IN+/-) (BD5638NUX) RIN Active to standby shift kohm *1:B.W. =20 kHz-LPF, BTL: The voltage between 5 pin and 8 pin ●Measurement Circuit Diagram VSTBY A STBY 1 Bias Vin 0.47µF Vin 1µF 8Ω V V VSE V VSE VBTL 10µF 6 3 PWM IN- 22µH GND 7 NC 2 0.47µF IN+ OUT- 8 OSC HBridge VDD OUT+ 22µH 5 4 1µF A VDD ●Active/Standby Control STBY Pin (1pin) Mode Pin Level Conditions Active H IC Active Standby L IC Shutdown www.rohm.com © 2010 ROHM Co., Ltd. All rights reserved. 2/14 2010.06 - Rev.A Technical Note BD5632NUX, BD5634NUX, BD5638NUX ●Package Outline Top View BD5632NUX BD5634NUX D56 32 D56 34 Lot No. Lot No. Bottom View BD5638NUX D56 38 Lot No. (Unit: mm) PKG: VSON008X2030 ●Block Diagram STBY 1 NC 2 IN+ ●Pin Assignment Chart Bias OSC OUT- 7 GND 6 3 PWM IN- 8 4 www.rohm.com © 2010 ROHM Co., Ltd. All rights reserved. VDD HBridge 5 3/14 OUT+ PIN No. PIN Name 1 STBY 2 NC 3 IN+ 4 IN- 5 OUT+ 6 VDD 7 GND 8 OUT- ※NC : Non Connection 2010.06 - Rev.A Technical Note BD5632NUX, BD5634NUX, BD5638NUX ●Application Circuit Example 10μ VDD 6 H：Active STBY 1 L：Shutdown Audio Input+ Differential Input Bias OSC OUT- IN+ 3 8 HBridge PWM Audio Input- IN4 OUT+ 6 GND 7 Fig.1 Differential Input for mobile phone 10μ VDD 6 H：Active STBY 1 L：Shutdown Audio Input+ 0.47μ Bias OSC IN+ OUT8 3 Differential Input Audio Input- HBridge PWM 0.47μ IN4 OUT+ 5 GND 7 Fig.2 Differential input with coupling input capacitors 10μ VDD 6 H：Active STBY 1 L：Shutdown Audio Input 0.47μ Bias OSC IN+ OUT- 3 8 PWM 0.47μ IN4 HBridge OUT+ 5 GND 7 Fig.3 Single-Ended input www.rohm.com © 2010 ROHM Co., Ltd. All rights reserved. 4/14 2010.06 - Rev.A Technical Note BD5632NUX, BD5634NUX, BD5638NUX ●Evaluation board Circuit Diagram VDD C3 10μ VDD 6 U1 S1 H：Active STBY 1 L：Shutdown Bias OSC 300k Audio Input+ 0.47μ OUT8 IN+ Ri 3 C2 Differential Input Audio Input- 0.47μ PWM IN- HBridge 4 C1 OUT+ 5 Ri GND 7 Please connect to GND line. Please connect to Power Supply (VDD=+2.5～5.5V) line. Please connect to Input Signal line. www.rohm.com © 2010 ROHM Co., Ltd. All rights reserved. 5/14 Please connect to Speaker. 2010.06 - Rev.A Technical Note BD5632NUX, BD5634NUX, BD5638NUX ●Evaluation board Parts List Qty. Item Description SMD Size 2 C1, C2 1 C3 Capacitor, 10μF 1 S1 Slide Switch 4mm X 10.2mm Murata GRM188R71A474KA01D ROHM TCFGA1A106M8R NKK SS-12SDP2 1 U1 IC Mono Class-D audio amplifier 2.0mm X 3.0mm VSON Package ROHM BD5632/34/38NUX 1 PCB1 Capacitor, 0.47μF 0603 A (3216) Printed-circuit board, BD5632/34/38NUX EVM ― Manufacturer / Part Number ― ●Description of External components 1. Input coupling capacitor (C1, C2) It makes an Input coupling capacitor 0.47µF. It sets cutoff frequency fc by the following formula by input coupling capacitor C1 (=C2) and input impedance Ri. fc 1 [Hz] 2π Ri C 1 In case of C1 (=C2) =0.47µF BD5632NUX Ri =100kΩ : fc=3.5Hz BD5634NUX Ri =50kΩ : fc=7Hz BD5638NUX Ri =25kΩ : fc=14Hz 2. Power decoupling capacitor (C3) It makes a power decoupling capacitor 10µF. When making capacitance of the power decoupling capacitor, there is an influence in the Audio characteristic. When making small, careful for the Audio characteristic at the actual application. www.rohm.com © 2010 ROHM Co., Ltd. All rights reserved. 6/14 2010.06 - Rev.A Technical Note BD5632NUX, BD5634NUX, BD5638NUX ●Evaluation board PCB layer TOP Layer silk pattern TOP Layer Bottom Layer www.rohm.com © 2010 ROHM Co., Ltd. All rights reserved. 7/14 2010.06 - Rev.A Technical Note BD5632NUX, BD5634NUX, BD5638NUX ●The way of evaluating Audio characteristic Evaluation Circuit Diagram VDD C3 0.1μ VDD H：Active C4 10μ VDD 6 STBY L：Shutdown 1 Bias OSC 300k Audio Input+ 0.47μ OUT- IN+ Ri=100k 3 C2 Differential Input Audio Input- HBridge PWM 0.47μ IN4 C1 1μF Audio Precision etc RL BTL OUT+ 1μF 5 Ri=100k Measument Instrumen 22μH 8 + 22μH RL=Speaker Load GND 7 When measuring Audio characteristics, insert LC filter during the output terminal of IC and the speaker load and measure it. Arrange LC filter as close as possible to the output terminal of IC. In case of L=22µH, C=1µF, the cut-off frequency becomes the following. Use a big current type - Inductor L. (Reference) TDK : SLF12575T-220M4R0 fc 1 2π LC 1 2π 22 μH 1μF www.rohm.com © 2010 ROHM Co., Ltd. All rights reserved. 34 kHz 8/14 2010.06 - Rev.A Technical Note BD5632NUX, BD5634NUX, BD5638NUX ●About the thermal design by the IC Characteristics of an IC have a great deal to do with the temperature at which it is used, and exceeding absolute maximum ratings may degrade and destroy elements. Careful consideration must be given to the heat of the IC from the two standpoints of immediate damage and long-term reliability of operation. Pay attention to points such as the following. Since a maximum junction temperature (TjMAX.)or operating temperature range (Topr) is shown in the absolute maximum ratings of the IC, to reference the value, find it using the Pd-Ta characteristic (temperature derating curve). If an input signal is too great when there is insufficient radiation, TSD (thermal shutdown) may operate. TSD, which operates at a chip temperature of approximately +180deg, is canceled when this goes below approximately +100deg. Since TSD operates persistently with the purpose of preventing chip damage, be aware that long-term use in the vicinity that TSD affects decrease IC reliability. Temperature Derating Curve Reference Data VSON008X2030 Power Dissipation Pd(W） 1.0 Measurement conditions: IC unit and Rohm standard board mount board size : 70mm×70mm x 1.6mm 1layer 0.52W θja = 240.4 deg/W 0.5 0.0 0 25 50 75 85 100 125 150 Ambient Temperature Ta (deg) Note) Values are actual measurements and are not guaranteed. Power dissipation values vary according to the board on which the IC is mounted. The Power dissipation of this IC when mounted on a multilayer board designed to radiate is greater than the values in the graph above. www.rohm.com © 2010 ROHM Co., Ltd. All rights reserved. 9/14 2010.06 - Rev.A Technical Note BD5632NUX, BD5634NUX, BD5638NUX ●Reference Data Efficiency - Output power f=1kHz RL=8Ω+33uH LC-filter(22uH+1uF) Icc vs Output power f=1kHz RL=8Ω+33uH LC-filter(22uH+1uF) 350 100.0 90.0 300 80.0 250 Icc [mA] Efficiency [%] 70.0 60.0 200 50.0 150 VDD=2.5V VDD=3.6V VDD=5.0V 40.0 30.0 20.0 VDD=2.5V VDD=3.6V VDD=5.0V 100 50 10.0 0.0 0 0 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 Po [W] 1 0 1.1 1.2 0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9 Po [W] Fig.4 1 1.1 1.2 Fig.5 Efficiency vs Output power f=1kHz RL=4Ω+33uH LC-filter(22uH+1uF) 90 Icc vs Output power f=1kHz RL=4Ω+33uH LC-filter(22uH+1uF) 700 80 600 500 60 50 Icc [mA] Efficiency [%] 70 VDD=2.5V VDD=3.6V VDD=5.0V 40 30 400 300 VDD=2.5V VDD=3.6V VDD=5.0V 200 20 100 10 0 0 0 0.2 0.4 0.6 0.8 1 1.2 1.4 1.6 1.8 0 2 0.2 0.4 0.6 Po [W] Fig.6 0.8 1 1.2 Po [W] 1.4 1.6 1.8 2 Fig.7 Icc - VDD No load, No signal Istby - VDD 4 0.5 3.5 0.4 2.5 0.3 Istby [uA] Icc [mA] 3 2 1.5 1 0.2 0.1 0.5 0 0 0 1 2 3 VDD [V] 4 5 6 0 1 2 Fig.8 5 6 Output power vs RL THD+N=1% f=1kHz LC-filter(22uH+1uF) 400Hz-30kHz 2.0 1.8 2.4 Po [W] 1.6 VDD=2.5V VDD=3.6V VDD=5.0V 1.6 1.4 VDD=2.5V VDD=3.6V VDD=5.0V 2.0 Po [W] 4 Fig.9 Output power vs RL THD+N=10% f=1kHz LC-filter(22uH+1uF) 400Hz-30kHz 2.8 3 VDD [V] 1.2 1.2 1.0 0.8 0.6 0.4 0.8 0.4 0.2 0.0 0.0 4 8 12 16 20 24 28 32 4 8 12 16 20 RL [Ω] RL [Ω] Fig.10 Fig.11 www.rohm.com © 2010 ROHM Co., Ltd. All rights reserved. 10/14 24 28 32 2010.06 - Rev.A Technical Note BD5632NUX, BD5634NUX, BD5638NUX Output power vs VDD f=1kHz LC-filter(22uH+1uF) 400Hz-30kHz THD+N vs Output power RL=4Ω f=1kHz LC-filter(22uH+1uF) 400Hz-30kHz 10 2.5 RL=8Ω：THD+N=1% RL=8Ω：THD+N=10% 2.0 RL=4Ω：THD+N=1% RL=4Ω：THD+N=10% VDD=2.5V VDD=3.6V THD+N [%] Po [W] 3.0 1.5 1.0 VDD=5.0V 1 0.5 0.1 0.01 0.0 2.5 3 3.5 VDD [V] 4 4.5 5 0.1 Fig.12 Po [W] 1 10 Fig.13 THD+N vs Output power RL=8Ω f=1kHz LC-filter(22uH+1uF) 400Hz-30kHz THD+N vs Frequency VDD=5.0V RL=8Ω LC-filter(22uH+1uF) 30kHz-LPF 10 10 THD+N [%] THD+N [%] VDD=2.5V VDD=3.6V VDD=5.0V 1 Po=50mW Po=250mW Po=1W 1 0.1 0.01 0.1 0.01 0.1 Po [W] 1 10 10 100 Fig.14 Po=25mW Po=125mW Po=500mW Po=15mW Po=75mW Po=200mW 1 THD+N [%] THD+N [%] 100k THD+N vs Frequency VDD=2.5V RL=8Ω LC-filter(22uH+1uF) 30kHz-LPF 10 1 10k Fig.15 THD+N vs Frequency VDD=3.6V RL=8Ω LC-filter(22uH+1uF) 30kHz-LPF 10 1k freq [Hz] 0.1 0.1 0.01 0.01 10 100 1k freq [Hz] 10k 10 100k 100 1k 10k 100k freq [Hz] Fig.16 Fig.17 THD+N_vs_Common Mode Input Voltage f=1kHz RL=8Ω Po=200mW LC-filter(22uH+1uF) 400Hz-30kHz THD+N vs Frequency RL=4Ω Po=250mW LC-filter(22uH+1uF) 30kHz-LPF 10 2 VDD-3.6V 1.6 VDD=5.0V 1.4 THD+N [%] THD+N [%] 1 VDD=2.5V 1.8 VDD=2.5V VDD=3.6V VDD=5.0V 0.1 1.2 1 0.8 0.6 0.4 0.2 0.01 0 10 100 1k freq [Hz] 10k 100k 0 www.rohm.com 8 Fig.19 Fig.18 © 2010 ROHM Co., Ltd. All rights reserved. 2 4 6 Vic - Common Mode Input Voltage [V] 11/14 2010.06 - Rev.A Technical Note BD5632NUX, BD5634NUX, BD5638NUX PSRR RL=4Ω Vripple=0.1Vpp Inputs ac-Grounded LC-filter(22uH+1uF) 30kHz-LPF 0 PSRR RL=8Ω Vripple=0.1Vpp Inputs ac-Grounded LC-filter(22uH+1uF) 30kHz-LPF 0 -10 -10 VDD=2.5V VDD=3.6V VDD=5.0V VDD=2.5V -20 -20 PSRR [dB] PSRR [dB] VDD=3.6V VDD=5.0V -30 -30 -40 -40 -50 -50 -60 -60 10 100 1k f [Hz] 10k 10 100k 100 1k f [Hz] Fig.20 THD+N vs Frequency VDD=5.0V RL=4Ω LC-filter(22uH+1uF) 30kHz-LPF 10 -30 Po=50mW Po=250mW Po=1W -35 VDD=2.5V VDD=3.6V VDD=5.0V 1 THD+N [%] CMRR [dB] 100k Fig.21 CMRR RL=8Ω Vin=1Vpp LC-filter(22uH+1uF) 30kHz-LPF -40 10k -45 0.1 -50 0.01 -55 10 100 1k freq [Hz] 10k 10 100k 100 Fig.22 10k 100k Fig.23 THD+N vs Frequency VDD=3.6V RL=4Ω LC-filter(22uH+1uF) 30kHz-LPF THD+N vs Frequency VDD=2.5V RL=4Ω LC-filter(22uH+1uF) 30kHz-LPF 10 10 Po=25mW Po=125mW Po=500mW Po=15mW Po=75mW 1 Po=200mW THD+N [%] THD+N [%] 1 0.1 0.1 0.01 0.01 10 100 1k freq [Hz] 10k 10 100k 100 20 15 15 10 10 gain [dB] 20 VDD=2.5V VDD=3.6V VDD=5.0V 0 10k 100k Gain vs Frequency RL=8Ω Vin=0.5Vpp LC-filter(22uH+1uF) 30kHz-LPF Gain_vs_Frequency RL=4Ω Vin=0.5Vpp LC-filter(22uH+1uF) 30kHz-LPF 5 1k freq [Hz] Fig.25 Fig.24 gain [dB] 1k freq [Hz] VDD=2.5V VDD=3.6V VDD=5.0V 5 0 -5 -5 10 100 1k freq [Hz] 10k 100k www.rohm.com 100 1k freq [Hz] 10k 100k Fig.27 Fig.26 © 2010 ROHM Co., Ltd. All rights reserved. 10 12/14 2010.06 - Rev.A Technical Note BD5632NUX, BD5634NUX, BD5638NUX ●Notes for use (1) Numbers and data in entries are representative design values and are not guaranteed values of the items. (2) Although we are confident recommending the sample application circuit, carefully check their characteristics further when using them. When modifying externally attached component constants before use, determine them so that they have sufficient margins by taking into account variations in externally attached components and the Rohm IC, not only for static characteristics but also including transient characteristics. (3) Absolute maximum ratings This IC may be damaged if the absolute maximum ratings for the applied voltage, temperature range, or other parameters are exceeded. Therefore, avoid using a voltage or temperature that exceeds the absolute maximum ratings. If it is possible that absolute maximum ratings will be exceeded, use fuses or other physical safety measures and determine ways to avoid exceeding the IC's absolute maximum ratings. (4) GND terminal’s potential Try to set the minimum voltage for GND terminal’s potential, regardless of the operation mode. (5) Shorting between pins and mounting errors When mounting the IC chip on a board, be very careful to set the chip's orientation and position precisely. When the power is turned on, the IC may be damaged if it is not mounted correctly. The IC may also be damaged if a short occurs (due to a foreign object, etc.) between two pins, between a pin and the power supply, or between a pin and the GND. (6) Operation in strong magnetic fields Note with caution that operation faults may occur when this IC operates in a strong magnetic field. (7) Thermal design Ensure sufficient margins to the thermal design by taking in to account the allowable power dissipation during actual use modes, because this IC is power amp. When excessive signal inputs which the heat dissipation is insufficient condition, it is possible that thermal shutdown circuit is active. (8) Thermal shutdown circuit This product is provided with a built-in thermal shutdown circuit. When the thermal shutdown circuit operates, the output transistors are placed under open status. The thermal shutdown circuit is primarily intended to shut down the IC avoiding thermal runaway under abnormal conditions with a chip temperature exceeding Tjmax = +150deg, and is not intended to protect and secure an electrical appliance. (9) Load of the output terminal This IC corresponds to dynamic speaker load, and doesn't correspond to the load except for dynamic speakers. (10) The short protection of the output terminal The short-circuiting protection of this IC corresponds only to “VDD-short” (the short-circuiting with the power) of the output terminal and “GND-short” (the short-circuiting with GND) of the output terminal. It doesn't correspond to the short-circuiting among the output terminals. Also, when the short-circuiting condition of the output terminal is canceled, it detects the high impedance of the output terminal and it is equipped with the auto recover without power cycling(the cancellation) function in the short-circuiting protection. Be careful of the output terminal, because, there is a fear not to return automatically when the short-circuiting condition occurs in pull-up or the pull-down at equal to or less than about 1MΩ impedance. (11) Operating ranges The rated operating power supply voltage range (VDD=+2.5V ~ +5.5V) and the rated operating temperature range (Ta=-40deg ~ +85deg) are the range by which basic circuit functions is operated. Characteristics and rated output power are not guaranteed in all power supply voltage ranges or temperature ranges. (12) Electrical characteristics Electrical characteristics show the typical performance of device and depend on board layout, parts, power supply. The standard value is in mounting device and parts on surface of ROHM’s board directly. (13) Power decoupling capacitor Because the big peak current flows through the power line, the class-D amplifier has an influence on the Audio characteristic by the capacitance value or the arrangement part of the power decoupling capacitor. Arrange a power decoupling capacitor as close as possible to the VDD terminal of IC. (14) NC terminal (Pin2) NC terminal (Non Connection Pin) does not connect to the inside circuit. Therefore, please open or connect to GND. www.rohm.com © 2010 ROHM Co., Ltd. All rights reserved. 13/14 2010.06 - Rev.A Technical Note BD5632NUX, BD5634NUX, BD5638NUX ●Ordering part number B D 5 Part No. 6 3 2 Part No. 5632 5634 5638 N U X - T Package NUX:VSON008X2030 R Packaging and forming specification TR: Embossed tape and reel VSON008X2030 <Tape and Reel information> 3.0±0.1 2.0±0.1 0.6MAX 1PIN MARK 0.25 TR The direction is the 1pin of product is at the upper right when you hold ( reel on the left hand and you pull out the tape on the right hand ) (0.12) +0.03 0.02 −0.02 1.5±0.1 4000pcs 0.5 1 4 8 5 1.4±0.1 0.3±0.1 C0.25 Embossed carrier tape Quantity Direction of feed S 0.08 S Tape 1pin +0.05 0.25 −0.04 Reel (Unit : mm) www.rohm.com © 2010 ROHM Co., Ltd. All rights reserved. 14/14 Direction of feed ∗ Order quantity needs to be multiple of the minimum quantity. 2010.06 - Rev.A Notice Notes No copying or reproduction of this document, in part or in whole, is permitted without the consent of ROHM Co.,Ltd. The content specified herein is subject to change for improvement without notice. The content specified herein is for the purpose of introducing ROHM's products (hereinafter "Products"). If you wish to use any such Product, please be sure to refer to the specifications, which can be obtained from ROHM upon request. Examples of application circuits, circuit constants and any other information contained herein illustrate the standard usage and operations of the Products. The peripheral conditions must be taken into account when designing circuits for mass production. Great care was taken in ensuring the accuracy of the information specified in this document. However, should you incur any damage arising from any inaccuracy or misprint of such information, ROHM shall bear no responsibility for such damage. The technical information specified herein is intended only to show the typical functions of and examples of application circuits for the Products. ROHM does not grant you, explicitly or implicitly, any license to use or exercise intellectual property or other rights held by ROHM and other parties. ROHM shall bear no responsibility whatsoever for any dispute arising from the use of such technical information. The Products specified in this document are intended to be used with general-use electronic equipment or devices (such as audio visual equipment, office-automation equipment, communication devices, electronic appliances and amusement devices). The Products specified in this document are not designed to be radiation tolerant. While ROHM always makes efforts to enhance the quality and reliability of its Products, a Product may fail or malfunction for a variety of reasons. Please be sure to implement in your equipment using the Products safety measures to guard against the possibility of physical injury, fire or any other damage caused in the event of the failure of any Product, such as derating, redundancy, fire control and fail-safe designs. ROHM shall bear no responsibility whatsoever for your use of any Product outside of the prescribed scope or not in accordance with the instruction manual. The Products are not designed or manufactured to be used with any equipment, device or system which requires an extremely high level of reliability the failure or malfunction of which may result in a direct threat to human life or create a risk of human injury (such as a medical instrument, transportation equipment, aerospace machinery, nuclear-reactor controller, fuelcontroller or other safety device). ROHM shall bear no responsibility in any way for use of any of the Products for the above special purposes. If a Product is intended to be used for any such special purpose, please contact a ROHM sales representative before purchasing. If you intend to export or ship overseas any Product or technology specified herein that may be controlled under the Foreign Exchange and the Foreign Trade Law, you will be required to obtain a license or permit under the Law. Thank you for your accessing to ROHM product informations. More detail product informations and catalogs are available, please contact us. ROHM Customer Support System http://www.rohm.com/contact/ www.rohm.com © 2010 ROHM Co., Ltd. All rights reserved. R1010A